Add the rt linux 4.1.3-rt3 as base
[kvmfornfv.git] / kernel / sound / soc / cirrus / ep93xx-ac97.c
1 /*
2  * ASoC driver for Cirrus Logic EP93xx AC97 controller.
3  *
4  * Copyright (c) 2010 Mika Westerberg
5  *
6  * Based on s3c-ac97 ASoC driver by Jaswinder Singh.
7  *
8  * This program is free software; you can redistribute it and/or modify
9  * it under the terms of the GNU General Public License version 2 as
10  * published by the Free Software Foundation.
11  */
12
13 #include <linux/delay.h>
14 #include <linux/err.h>
15 #include <linux/io.h>
16 #include <linux/init.h>
17 #include <linux/module.h>
18 #include <linux/platform_device.h>
19 #include <linux/slab.h>
20
21 #include <sound/core.h>
22 #include <sound/dmaengine_pcm.h>
23 #include <sound/ac97_codec.h>
24 #include <sound/soc.h>
25
26 #include <linux/platform_data/dma-ep93xx.h>
27
28 #include "ep93xx-pcm.h"
29
30 /*
31  * Per channel (1-4) registers.
32  */
33 #define AC97CH(n)               (((n) - 1) * 0x20)
34
35 #define AC97DR(n)               (AC97CH(n) + 0x0000)
36
37 #define AC97RXCR(n)             (AC97CH(n) + 0x0004)
38 #define AC97RXCR_REN            BIT(0)
39 #define AC97RXCR_RX3            BIT(3)
40 #define AC97RXCR_RX4            BIT(4)
41 #define AC97RXCR_CM             BIT(15)
42
43 #define AC97TXCR(n)             (AC97CH(n) + 0x0008)
44 #define AC97TXCR_TEN            BIT(0)
45 #define AC97TXCR_TX3            BIT(3)
46 #define AC97TXCR_TX4            BIT(4)
47 #define AC97TXCR_CM             BIT(15)
48
49 #define AC97SR(n)               (AC97CH(n) + 0x000c)
50 #define AC97SR_TXFE             BIT(1)
51 #define AC97SR_TXUE             BIT(6)
52
53 #define AC97RISR(n)             (AC97CH(n) + 0x0010)
54 #define AC97ISR(n)              (AC97CH(n) + 0x0014)
55 #define AC97IE(n)               (AC97CH(n) + 0x0018)
56
57 /*
58  * Global AC97 controller registers.
59  */
60 #define AC97S1DATA              0x0080
61 #define AC97S2DATA              0x0084
62 #define AC97S12DATA             0x0088
63
64 #define AC97RGIS                0x008c
65 #define AC97GIS                 0x0090
66 #define AC97IM                  0x0094
67 /*
68  * Common bits for RGIS, GIS and IM registers.
69  */
70 #define AC97_SLOT2RXVALID       BIT(1)
71 #define AC97_CODECREADY         BIT(5)
72 #define AC97_SLOT2TXCOMPLETE    BIT(6)
73
74 #define AC97EOI                 0x0098
75 #define AC97EOI_WINT            BIT(0)
76 #define AC97EOI_CODECREADY      BIT(1)
77
78 #define AC97GCR                 0x009c
79 #define AC97GCR_AC97IFE         BIT(0)
80
81 #define AC97RESET               0x00a0
82 #define AC97RESET_TIMEDRESET    BIT(0)
83
84 #define AC97SYNC                0x00a4
85 #define AC97SYNC_TIMEDSYNC      BIT(0)
86
87 #define AC97_TIMEOUT            msecs_to_jiffies(5)
88
89 /**
90  * struct ep93xx_ac97_info - EP93xx AC97 controller info structure
91  * @lock: mutex serializing access to the bus (slot 1 & 2 ops)
92  * @dev: pointer to the platform device dev structure
93  * @regs: mapped AC97 controller registers
94  * @done: bus ops wait here for an interrupt
95  */
96 struct ep93xx_ac97_info {
97         struct mutex            lock;
98         struct device           *dev;
99         void __iomem            *regs;
100         struct completion       done;
101         struct snd_dmaengine_dai_dma_data dma_params_rx;
102         struct snd_dmaengine_dai_dma_data dma_params_tx;
103 };
104
105 /* currently ALSA only supports a single AC97 device */
106 static struct ep93xx_ac97_info *ep93xx_ac97_info;
107
108 static struct ep93xx_dma_data ep93xx_ac97_pcm_out = {
109         .name           = "ac97-pcm-out",
110         .port           = EP93XX_DMA_AAC1,
111         .direction      = DMA_MEM_TO_DEV,
112 };
113
114 static struct ep93xx_dma_data ep93xx_ac97_pcm_in = {
115         .name           = "ac97-pcm-in",
116         .port           = EP93XX_DMA_AAC1,
117         .direction      = DMA_DEV_TO_MEM,
118 };
119
120 static inline unsigned ep93xx_ac97_read_reg(struct ep93xx_ac97_info *info,
121                                             unsigned reg)
122 {
123         return __raw_readl(info->regs + reg);
124 }
125
126 static inline void ep93xx_ac97_write_reg(struct ep93xx_ac97_info *info,
127                                          unsigned reg, unsigned val)
128 {
129         __raw_writel(val, info->regs + reg);
130 }
131
132 static unsigned short ep93xx_ac97_read(struct snd_ac97 *ac97,
133                                        unsigned short reg)
134 {
135         struct ep93xx_ac97_info *info = ep93xx_ac97_info;
136         unsigned short val;
137
138         mutex_lock(&info->lock);
139
140         ep93xx_ac97_write_reg(info, AC97S1DATA, reg);
141         ep93xx_ac97_write_reg(info, AC97IM, AC97_SLOT2RXVALID);
142         if (!wait_for_completion_timeout(&info->done, AC97_TIMEOUT)) {
143                 dev_warn(info->dev, "timeout reading register %x\n", reg);
144                 mutex_unlock(&info->lock);
145                 return -ETIMEDOUT;
146         }
147         val = (unsigned short)ep93xx_ac97_read_reg(info, AC97S2DATA);
148
149         mutex_unlock(&info->lock);
150         return val;
151 }
152
153 static void ep93xx_ac97_write(struct snd_ac97 *ac97,
154                               unsigned short reg,
155                               unsigned short val)
156 {
157         struct ep93xx_ac97_info *info = ep93xx_ac97_info;
158
159         mutex_lock(&info->lock);
160
161         /*
162          * Writes to the codec need to be done so that slot 2 is filled in
163          * before slot 1.
164          */
165         ep93xx_ac97_write_reg(info, AC97S2DATA, val);
166         ep93xx_ac97_write_reg(info, AC97S1DATA, reg);
167
168         ep93xx_ac97_write_reg(info, AC97IM, AC97_SLOT2TXCOMPLETE);
169         if (!wait_for_completion_timeout(&info->done, AC97_TIMEOUT))
170                 dev_warn(info->dev, "timeout writing register %x\n", reg);
171
172         mutex_unlock(&info->lock);
173 }
174
175 static void ep93xx_ac97_warm_reset(struct snd_ac97 *ac97)
176 {
177         struct ep93xx_ac97_info *info = ep93xx_ac97_info;
178
179         mutex_lock(&info->lock);
180
181         /*
182          * We are assuming that before this functions gets called, the codec
183          * BIT_CLK is stopped by forcing the codec into powerdown mode. We can
184          * control the SYNC signal directly via AC97SYNC register. Using
185          * TIMEDSYNC the controller will keep the SYNC high > 1us.
186          */
187         ep93xx_ac97_write_reg(info, AC97SYNC, AC97SYNC_TIMEDSYNC);
188         ep93xx_ac97_write_reg(info, AC97IM, AC97_CODECREADY);
189         if (!wait_for_completion_timeout(&info->done, AC97_TIMEOUT))
190                 dev_warn(info->dev, "codec warm reset timeout\n");
191
192         mutex_unlock(&info->lock);
193 }
194
195 static void ep93xx_ac97_cold_reset(struct snd_ac97 *ac97)
196 {
197         struct ep93xx_ac97_info *info = ep93xx_ac97_info;
198
199         mutex_lock(&info->lock);
200
201         /*
202          * For doing cold reset, we disable the AC97 controller interface, clear
203          * WINT and CODECREADY bits, and finally enable the interface again.
204          */
205         ep93xx_ac97_write_reg(info, AC97GCR, 0);
206         ep93xx_ac97_write_reg(info, AC97EOI, AC97EOI_CODECREADY | AC97EOI_WINT);
207         ep93xx_ac97_write_reg(info, AC97GCR, AC97GCR_AC97IFE);
208
209         /*
210          * Now, assert the reset and wait for the codec to become ready.
211          */
212         ep93xx_ac97_write_reg(info, AC97RESET, AC97RESET_TIMEDRESET);
213         ep93xx_ac97_write_reg(info, AC97IM, AC97_CODECREADY);
214         if (!wait_for_completion_timeout(&info->done, AC97_TIMEOUT))
215                 dev_warn(info->dev, "codec cold reset timeout\n");
216
217         /*
218          * Give the codec some time to come fully out from the reset. This way
219          * we ensure that the subsequent reads/writes will work.
220          */
221         usleep_range(15000, 20000);
222
223         mutex_unlock(&info->lock);
224 }
225
226 static irqreturn_t ep93xx_ac97_interrupt(int irq, void *dev_id)
227 {
228         struct ep93xx_ac97_info *info = dev_id;
229         unsigned status, mask;
230
231         /*
232          * Just mask out the interrupt and wake up the waiting thread.
233          * Interrupts are cleared via reading/writing to slot 1 & 2 registers by
234          * the waiting thread.
235          */
236         status = ep93xx_ac97_read_reg(info, AC97GIS);
237         mask = ep93xx_ac97_read_reg(info, AC97IM);
238         mask &= ~status;
239         ep93xx_ac97_write_reg(info, AC97IM, mask);
240
241         complete(&info->done);
242         return IRQ_HANDLED;
243 }
244
245 static struct snd_ac97_bus_ops ep93xx_ac97_ops = {
246         .read           = ep93xx_ac97_read,
247         .write          = ep93xx_ac97_write,
248         .reset          = ep93xx_ac97_cold_reset,
249         .warm_reset     = ep93xx_ac97_warm_reset,
250 };
251
252 static int ep93xx_ac97_trigger(struct snd_pcm_substream *substream,
253                                int cmd, struct snd_soc_dai *dai)
254 {
255         struct ep93xx_ac97_info *info = snd_soc_dai_get_drvdata(dai);
256         unsigned v = 0;
257
258         switch (cmd) {
259         case SNDRV_PCM_TRIGGER_START:
260         case SNDRV_PCM_TRIGGER_RESUME:
261         case SNDRV_PCM_TRIGGER_PAUSE_RELEASE:
262                 if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK) {
263                         /*
264                          * Enable compact mode, TX slots 3 & 4, and the TX FIFO
265                          * itself.
266                          */
267                         v |= AC97TXCR_CM;
268                         v |= AC97TXCR_TX3 | AC97TXCR_TX4;
269                         v |= AC97TXCR_TEN;
270                         ep93xx_ac97_write_reg(info, AC97TXCR(1), v);
271                 } else {
272                         /*
273                          * Enable compact mode, RX slots 3 & 4, and the RX FIFO
274                          * itself.
275                          */
276                         v |= AC97RXCR_CM;
277                         v |= AC97RXCR_RX3 | AC97RXCR_RX4;
278                         v |= AC97RXCR_REN;
279                         ep93xx_ac97_write_reg(info, AC97RXCR(1), v);
280                 }
281                 break;
282
283         case SNDRV_PCM_TRIGGER_STOP:
284         case SNDRV_PCM_TRIGGER_SUSPEND:
285         case SNDRV_PCM_TRIGGER_PAUSE_PUSH:
286                 if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK) {
287                         /*
288                          * As per Cirrus EP93xx errata described below:
289                          *
290                          * http://www.cirrus.com/en/pubs/errata/ER667E2B.pdf
291                          *
292                          * we will wait for the TX FIFO to be empty before
293                          * clearing the TEN bit.
294                          */
295                         unsigned long timeout = jiffies + AC97_TIMEOUT;
296
297                         do {
298                                 v = ep93xx_ac97_read_reg(info, AC97SR(1));
299                                 if (time_after(jiffies, timeout)) {
300                                         dev_warn(info->dev, "TX timeout\n");
301                                         break;
302                                 }
303                         } while (!(v & (AC97SR_TXFE | AC97SR_TXUE)));
304
305                         /* disable the TX FIFO */
306                         ep93xx_ac97_write_reg(info, AC97TXCR(1), 0);
307                 } else {
308                         /* disable the RX FIFO */
309                         ep93xx_ac97_write_reg(info, AC97RXCR(1), 0);
310                 }
311                 break;
312
313         default:
314                 dev_warn(info->dev, "unknown command %d\n", cmd);
315                 return -EINVAL;
316         }
317
318         return 0;
319 }
320
321 static int ep93xx_ac97_dai_probe(struct snd_soc_dai *dai)
322 {
323         struct ep93xx_ac97_info *info = snd_soc_dai_get_drvdata(dai);
324
325         info->dma_params_tx.filter_data = &ep93xx_ac97_pcm_out;
326         info->dma_params_rx.filter_data = &ep93xx_ac97_pcm_in;
327
328         dai->playback_dma_data = &info->dma_params_tx;
329         dai->capture_dma_data = &info->dma_params_rx;
330
331         return 0;
332 }
333
334 static const struct snd_soc_dai_ops ep93xx_ac97_dai_ops = {
335         .trigger        = ep93xx_ac97_trigger,
336 };
337
338 static struct snd_soc_dai_driver ep93xx_ac97_dai = {
339         .name           = "ep93xx-ac97",
340         .id             = 0,
341         .bus_control    = true,
342         .probe          = ep93xx_ac97_dai_probe,
343         .playback       = {
344                 .stream_name    = "AC97 Playback",
345                 .channels_min   = 2,
346                 .channels_max   = 2,
347                 .rates          = SNDRV_PCM_RATE_8000_48000,
348                 .formats        = SNDRV_PCM_FMTBIT_S16_LE,
349         },
350         .capture        = {
351                 .stream_name    = "AC97 Capture",
352                 .channels_min   = 2,
353                 .channels_max   = 2,
354                 .rates          = SNDRV_PCM_RATE_8000_48000,
355                 .formats        = SNDRV_PCM_FMTBIT_S16_LE,
356         },
357         .ops                    = &ep93xx_ac97_dai_ops,
358 };
359
360 static const struct snd_soc_component_driver ep93xx_ac97_component = {
361         .name           = "ep93xx-ac97",
362 };
363
364 static int ep93xx_ac97_probe(struct platform_device *pdev)
365 {
366         struct ep93xx_ac97_info *info;
367         struct resource *res;
368         unsigned int irq;
369         int ret;
370
371         info = devm_kzalloc(&pdev->dev, sizeof(*info), GFP_KERNEL);
372         if (!info)
373                 return -ENOMEM;
374
375         res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
376         info->regs = devm_ioremap_resource(&pdev->dev, res);
377         if (IS_ERR(info->regs))
378                 return PTR_ERR(info->regs);
379
380         irq = platform_get_irq(pdev, 0);
381         if (!irq)
382                 return -ENODEV;
383
384         ret = devm_request_irq(&pdev->dev, irq, ep93xx_ac97_interrupt,
385                                IRQF_TRIGGER_HIGH, pdev->name, info);
386         if (ret)
387                 goto fail;
388
389         dev_set_drvdata(&pdev->dev, info);
390
391         mutex_init(&info->lock);
392         init_completion(&info->done);
393         info->dev = &pdev->dev;
394
395         ep93xx_ac97_info = info;
396         platform_set_drvdata(pdev, info);
397
398         ret = snd_soc_set_ac97_ops(&ep93xx_ac97_ops);
399         if (ret)
400                 goto fail;
401
402         ret = snd_soc_register_component(&pdev->dev, &ep93xx_ac97_component,
403                                          &ep93xx_ac97_dai, 1);
404         if (ret)
405                 goto fail;
406
407         ret = devm_ep93xx_pcm_platform_register(&pdev->dev);
408         if (ret)
409                 goto fail_unregister;
410
411         return 0;
412
413 fail_unregister:
414         snd_soc_unregister_component(&pdev->dev);
415 fail:
416         ep93xx_ac97_info = NULL;
417         snd_soc_set_ac97_ops(NULL);
418         return ret;
419 }
420
421 static int ep93xx_ac97_remove(struct platform_device *pdev)
422 {
423         struct ep93xx_ac97_info *info = platform_get_drvdata(pdev);
424
425         snd_soc_unregister_component(&pdev->dev);
426
427         /* disable the AC97 controller */
428         ep93xx_ac97_write_reg(info, AC97GCR, 0);
429
430         ep93xx_ac97_info = NULL;
431
432         snd_soc_set_ac97_ops(NULL);
433
434         return 0;
435 }
436
437 static struct platform_driver ep93xx_ac97_driver = {
438         .probe  = ep93xx_ac97_probe,
439         .remove = ep93xx_ac97_remove,
440         .driver = {
441                 .name = "ep93xx-ac97",
442         },
443 };
444
445 module_platform_driver(ep93xx_ac97_driver);
446
447 MODULE_DESCRIPTION("EP93xx AC97 ASoC Driver");
448 MODULE_AUTHOR("Mika Westerberg <mika.westerberg@iki.fi>");
449 MODULE_LICENSE("GPL");
450 MODULE_ALIAS("platform:ep93xx-ac97");