1 #ifndef LINUX_SSB_CHIPCO_H_
2 #define LINUX_SSB_CHIPCO_H_
4 /* SonicsSiliconBackplane CHIPCOMMON core hardware definitions
6 * The chipcommon core provides chip identification, SB control,
7 * jtag, 0/1/2 uarts, clock frequency control, a watchdog interrupt timer,
8 * gpio interface, extbus, and support for serial and parallel flashes.
10 * Copyright 2005, Broadcom Corporation
11 * Copyright 2006, Michael Buesch <m@bues.ch>
13 * Licensed under the GPL version 2. See COPYING for details.
16 /** ChipCommon core registers. **/
18 #define SSB_CHIPCO_CHIPID 0x0000
19 #define SSB_CHIPCO_IDMASK 0x0000FFFF
20 #define SSB_CHIPCO_REVMASK 0x000F0000
21 #define SSB_CHIPCO_REVSHIFT 16
22 #define SSB_CHIPCO_PACKMASK 0x00F00000
23 #define SSB_CHIPCO_PACKSHIFT 20
24 #define SSB_CHIPCO_NRCORESMASK 0x0F000000
25 #define SSB_CHIPCO_NRCORESSHIFT 24
26 #define SSB_CHIPCO_CAP 0x0004 /* Capabilities */
27 #define SSB_CHIPCO_CAP_NRUART 0x00000003 /* # of UARTs */
28 #define SSB_CHIPCO_CAP_MIPSEB 0x00000004 /* MIPS in BigEndian Mode */
29 #define SSB_CHIPCO_CAP_UARTCLK 0x00000018 /* UART clock select */
30 #define SSB_CHIPCO_CAP_UARTCLK_INT 0x00000008 /* UARTs are driven by internal divided clock */
31 #define SSB_CHIPCO_CAP_UARTGPIO 0x00000020 /* UARTs on GPIO 15-12 */
32 #define SSB_CHIPCO_CAP_EXTBUS 0x000000C0 /* External buses present */
33 #define SSB_CHIPCO_CAP_FLASHT 0x00000700 /* Flash Type */
34 #define SSB_CHIPCO_FLASHT_NONE 0x00000000 /* No flash */
35 #define SSB_CHIPCO_FLASHT_STSER 0x00000100 /* ST serial flash */
36 #define SSB_CHIPCO_FLASHT_ATSER 0x00000200 /* Atmel serial flash */
37 #define SSB_CHIPCO_FLASHT_PARA 0x00000700 /* Parallel flash */
38 #define SSB_CHIPCO_CAP_PLLT 0x00038000 /* PLL Type */
39 #define SSB_PLLTYPE_NONE 0x00000000
40 #define SSB_PLLTYPE_1 0x00010000 /* 48Mhz base, 3 dividers */
41 #define SSB_PLLTYPE_2 0x00020000 /* 48Mhz, 4 dividers */
42 #define SSB_PLLTYPE_3 0x00030000 /* 25Mhz, 2 dividers */
43 #define SSB_PLLTYPE_4 0x00008000 /* 48Mhz, 4 dividers */
44 #define SSB_PLLTYPE_5 0x00018000 /* 25Mhz, 4 dividers */
45 #define SSB_PLLTYPE_6 0x00028000 /* 100/200 or 120/240 only */
46 #define SSB_PLLTYPE_7 0x00038000 /* 25Mhz, 4 dividers */
47 #define SSB_CHIPCO_CAP_PCTL 0x00040000 /* Power Control */
48 #define SSB_CHIPCO_CAP_OTPS 0x00380000 /* OTP size */
49 #define SSB_CHIPCO_CAP_OTPS_SHIFT 19
50 #define SSB_CHIPCO_CAP_OTPS_BASE 5
51 #define SSB_CHIPCO_CAP_JTAGM 0x00400000 /* JTAG master present */
52 #define SSB_CHIPCO_CAP_BROM 0x00800000 /* Internal boot ROM active */
53 #define SSB_CHIPCO_CAP_64BIT 0x08000000 /* 64-bit Backplane */
54 #define SSB_CHIPCO_CAP_PMU 0x10000000 /* PMU available (rev >= 20) */
55 #define SSB_CHIPCO_CAP_ECI 0x20000000 /* ECI available (rev >= 20) */
56 #define SSB_CHIPCO_CAP_SPROM 0x40000000 /* SPROM present */
57 #define SSB_CHIPCO_CORECTL 0x0008
58 #define SSB_CHIPCO_CORECTL_UARTCLK0 0x00000001 /* Drive UART with internal clock */
59 #define SSB_CHIPCO_CORECTL_SE 0x00000002 /* sync clk out enable (corerev >= 3) */
60 #define SSB_CHIPCO_CORECTL_UARTCLKEN 0x00000008 /* UART clock enable (rev >= 21) */
61 #define SSB_CHIPCO_BIST 0x000C
62 #define SSB_CHIPCO_OTPS 0x0010 /* OTP status */
63 #define SSB_CHIPCO_OTPS_PROGFAIL 0x80000000
64 #define SSB_CHIPCO_OTPS_PROTECT 0x00000007
65 #define SSB_CHIPCO_OTPS_HW_PROTECT 0x00000001
66 #define SSB_CHIPCO_OTPS_SW_PROTECT 0x00000002
67 #define SSB_CHIPCO_OTPS_CID_PROTECT 0x00000004
68 #define SSB_CHIPCO_OTPC 0x0014 /* OTP control */
69 #define SSB_CHIPCO_OTPC_RECWAIT 0xFF000000
70 #define SSB_CHIPCO_OTPC_PROGWAIT 0x00FFFF00
71 #define SSB_CHIPCO_OTPC_PRW_SHIFT 8
72 #define SSB_CHIPCO_OTPC_MAXFAIL 0x00000038
73 #define SSB_CHIPCO_OTPC_VSEL 0x00000006
74 #define SSB_CHIPCO_OTPC_SELVL 0x00000001
75 #define SSB_CHIPCO_OTPP 0x0018 /* OTP prog */
76 #define SSB_CHIPCO_OTPP_COL 0x000000FF
77 #define SSB_CHIPCO_OTPP_ROW 0x0000FF00
78 #define SSB_CHIPCO_OTPP_ROW_SHIFT 8
79 #define SSB_CHIPCO_OTPP_READERR 0x10000000
80 #define SSB_CHIPCO_OTPP_VALUE 0x20000000
81 #define SSB_CHIPCO_OTPP_READ 0x40000000
82 #define SSB_CHIPCO_OTPP_START 0x80000000
83 #define SSB_CHIPCO_OTPP_BUSY 0x80000000
84 #define SSB_CHIPCO_IRQSTAT 0x0020
85 #define SSB_CHIPCO_IRQMASK 0x0024
86 #define SSB_CHIPCO_IRQ_GPIO 0x00000001 /* gpio intr */
87 #define SSB_CHIPCO_IRQ_EXT 0x00000002 /* ro: ext intr pin (corerev >= 3) */
88 #define SSB_CHIPCO_IRQ_WDRESET 0x80000000 /* watchdog reset occurred */
89 #define SSB_CHIPCO_CHIPCTL 0x0028 /* Rev >= 11 only */
90 #define SSB_CHIPCO_CHIPSTAT 0x002C /* Rev >= 11 only */
91 #define SSB_CHIPCO_JCMD 0x0030 /* Rev >= 10 only */
92 #define SSB_CHIPCO_JCMD_START 0x80000000
93 #define SSB_CHIPCO_JCMD_BUSY 0x80000000
94 #define SSB_CHIPCO_JCMD_PAUSE 0x40000000
95 #define SSB_CHIPCO_JCMD0_ACC_MASK 0x0000F000
96 #define SSB_CHIPCO_JCMD0_ACC_IRDR 0x00000000
97 #define SSB_CHIPCO_JCMD0_ACC_DR 0x00001000
98 #define SSB_CHIPCO_JCMD0_ACC_IR 0x00002000
99 #define SSB_CHIPCO_JCMD0_ACC_RESET 0x00003000
100 #define SSB_CHIPCO_JCMD0_ACC_IRPDR 0x00004000
101 #define SSB_CHIPCO_JCMD0_ACC_PDR 0x00005000
102 #define SSB_CHIPCO_JCMD0_IRW_MASK 0x00000F00
103 #define SSB_CHIPCO_JCMD_ACC_MASK 0x000F0000 /* Changes for corerev 11 */
104 #define SSB_CHIPCO_JCMD_ACC_IRDR 0x00000000
105 #define SSB_CHIPCO_JCMD_ACC_DR 0x00010000
106 #define SSB_CHIPCO_JCMD_ACC_IR 0x00020000
107 #define SSB_CHIPCO_JCMD_ACC_RESET 0x00030000
108 #define SSB_CHIPCO_JCMD_ACC_IRPDR 0x00040000
109 #define SSB_CHIPCO_JCMD_ACC_PDR 0x00050000
110 #define SSB_CHIPCO_JCMD_IRW_MASK 0x00001F00
111 #define SSB_CHIPCO_JCMD_IRW_SHIFT 8
112 #define SSB_CHIPCO_JCMD_DRW_MASK 0x0000003F
113 #define SSB_CHIPCO_JIR 0x0034 /* Rev >= 10 only */
114 #define SSB_CHIPCO_JDR 0x0038 /* Rev >= 10 only */
115 #define SSB_CHIPCO_JCTL 0x003C /* Rev >= 10 only */
116 #define SSB_CHIPCO_JCTL_FORCE_CLK 4 /* Force clock */
117 #define SSB_CHIPCO_JCTL_EXT_EN 2 /* Enable external targets */
118 #define SSB_CHIPCO_JCTL_EN 1 /* Enable Jtag master */
119 #define SSB_CHIPCO_FLASHCTL 0x0040
120 #define SSB_CHIPCO_FLASHCTL_START 0x80000000
121 #define SSB_CHIPCO_FLASHCTL_BUSY SSB_CHIPCO_FLASHCTL_START
122 #define SSB_CHIPCO_FLASHADDR 0x0044
123 #define SSB_CHIPCO_FLASHDATA 0x0048
124 #define SSB_CHIPCO_BCAST_ADDR 0x0050
125 #define SSB_CHIPCO_BCAST_DATA 0x0054
126 #define SSB_CHIPCO_GPIOPULLUP 0x0058 /* Rev >= 20 only */
127 #define SSB_CHIPCO_GPIOPULLDOWN 0x005C /* Rev >= 20 only */
128 #define SSB_CHIPCO_GPIOIN 0x0060
129 #define SSB_CHIPCO_GPIOOUT 0x0064
130 #define SSB_CHIPCO_GPIOOUTEN 0x0068
131 #define SSB_CHIPCO_GPIOCTL 0x006C
132 #define SSB_CHIPCO_GPIOPOL 0x0070
133 #define SSB_CHIPCO_GPIOIRQ 0x0074
134 #define SSB_CHIPCO_WATCHDOG 0x0080
135 #define SSB_CHIPCO_GPIOTIMER 0x0088 /* LED powersave (corerev >= 16) */
136 #define SSB_CHIPCO_GPIOTIMER_OFFTIME 0x0000FFFF
137 #define SSB_CHIPCO_GPIOTIMER_OFFTIME_SHIFT 0
138 #define SSB_CHIPCO_GPIOTIMER_ONTIME 0xFFFF0000
139 #define SSB_CHIPCO_GPIOTIMER_ONTIME_SHIFT 16
140 #define SSB_CHIPCO_GPIOTOUTM 0x008C /* LED powersave (corerev >= 16) */
141 #define SSB_CHIPCO_CLOCK_N 0x0090
142 #define SSB_CHIPCO_CLOCK_SB 0x0094
143 #define SSB_CHIPCO_CLOCK_PCI 0x0098
144 #define SSB_CHIPCO_CLOCK_M2 0x009C
145 #define SSB_CHIPCO_CLOCK_MIPS 0x00A0
146 #define SSB_CHIPCO_CLKDIV 0x00A4 /* Rev >= 3 only */
147 #define SSB_CHIPCO_CLKDIV_SFLASH 0x0F000000
148 #define SSB_CHIPCO_CLKDIV_SFLASH_SHIFT 24
149 #define SSB_CHIPCO_CLKDIV_OTP 0x000F0000
150 #define SSB_CHIPCO_CLKDIV_OTP_SHIFT 16
151 #define SSB_CHIPCO_CLKDIV_JTAG 0x00000F00
152 #define SSB_CHIPCO_CLKDIV_JTAG_SHIFT 8
153 #define SSB_CHIPCO_CLKDIV_UART 0x000000FF
154 #define SSB_CHIPCO_PLLONDELAY 0x00B0 /* Rev >= 4 only */
155 #define SSB_CHIPCO_FREFSELDELAY 0x00B4 /* Rev >= 4 only */
156 #define SSB_CHIPCO_SLOWCLKCTL 0x00B8 /* 6 <= Rev <= 9 only */
157 #define SSB_CHIPCO_SLOWCLKCTL_SRC 0x00000007 /* slow clock source mask */
158 #define SSB_CHIPCO_SLOWCLKCTL_SRC_LPO 0x00000000 /* source of slow clock is LPO */
159 #define SSB_CHIPCO_SLOWCLKCTL_SRC_XTAL 0x00000001 /* source of slow clock is crystal */
160 #define SSB_CHIPCO_SLOECLKCTL_SRC_PCI 0x00000002 /* source of slow clock is PCI */
161 #define SSB_CHIPCO_SLOWCLKCTL_LPOFREQ 0x00000200 /* LPOFreqSel, 1: 160Khz, 0: 32KHz */
162 #define SSB_CHIPCO_SLOWCLKCTL_LPOPD 0x00000400 /* LPOPowerDown, 1: LPO is disabled, 0: LPO is enabled */
163 #define SSB_CHIPCO_SLOWCLKCTL_FSLOW 0x00000800 /* ForceSlowClk, 1: sb/cores running on slow clock, 0: power logic control */
164 #define SSB_CHIPCO_SLOWCLKCTL_IPLL 0x00001000 /* IgnorePllOffReq, 1/0: power logic ignores/honors PLL clock disable requests from core */
165 #define SSB_CHIPCO_SLOWCLKCTL_ENXTAL 0x00002000 /* XtalControlEn, 1/0: power logic does/doesn't disable crystal when appropriate */
166 #define SSB_CHIPCO_SLOWCLKCTL_XTALPU 0x00004000 /* XtalPU (RO), 1/0: crystal running/disabled */
167 #define SSB_CHIPCO_SLOWCLKCTL_CLKDIV 0xFFFF0000 /* ClockDivider (SlowClk = 1/(4+divisor)) */
168 #define SSB_CHIPCO_SLOWCLKCTL_CLKDIV_SHIFT 16
169 #define SSB_CHIPCO_SYSCLKCTL 0x00C0 /* Rev >= 3 only */
170 #define SSB_CHIPCO_SYSCLKCTL_IDLPEN 0x00000001 /* ILPen: Enable Idle Low Power */
171 #define SSB_CHIPCO_SYSCLKCTL_ALPEN 0x00000002 /* ALPen: Enable Active Low Power */
172 #define SSB_CHIPCO_SYSCLKCTL_PLLEN 0x00000004 /* ForcePLLOn */
173 #define SSB_CHIPCO_SYSCLKCTL_FORCEALP 0x00000008 /* Force ALP (or HT if ALPen is not set */
174 #define SSB_CHIPCO_SYSCLKCTL_FORCEHT 0x00000010 /* Force HT */
175 #define SSB_CHIPCO_SYSCLKCTL_CLKDIV 0xFFFF0000 /* ClkDiv (ILP = 1/(4+divisor)) */
176 #define SSB_CHIPCO_SYSCLKCTL_CLKDIV_SHIFT 16
177 #define SSB_CHIPCO_CLKSTSTR 0x00C4 /* Rev >= 3 only */
178 #define SSB_CHIPCO_PCMCIA_CFG 0x0100
179 #define SSB_CHIPCO_PCMCIA_MEMWAIT 0x0104
180 #define SSB_CHIPCO_PCMCIA_ATTRWAIT 0x0108
181 #define SSB_CHIPCO_PCMCIA_IOWAIT 0x010C
182 #define SSB_CHIPCO_IDE_CFG 0x0110
183 #define SSB_CHIPCO_IDE_MEMWAIT 0x0114
184 #define SSB_CHIPCO_IDE_ATTRWAIT 0x0118
185 #define SSB_CHIPCO_IDE_IOWAIT 0x011C
186 #define SSB_CHIPCO_PROG_CFG 0x0120
187 #define SSB_CHIPCO_PROG_WAITCNT 0x0124
188 #define SSB_CHIPCO_FLASH_CFG 0x0128
189 #define SSB_CHIPCO_FLASH_WAITCNT 0x012C
190 #define SSB_CHIPCO_CLKCTLST 0x01E0 /* Clock control and status (rev >= 20) */
191 #define SSB_CHIPCO_CLKCTLST_FORCEALP 0x00000001 /* Force ALP request */
192 #define SSB_CHIPCO_CLKCTLST_FORCEHT 0x00000002 /* Force HT request */
193 #define SSB_CHIPCO_CLKCTLST_FORCEILP 0x00000004 /* Force ILP request */
194 #define SSB_CHIPCO_CLKCTLST_HAVEALPREQ 0x00000008 /* ALP available request */
195 #define SSB_CHIPCO_CLKCTLST_HAVEHTREQ 0x00000010 /* HT available request */
196 #define SSB_CHIPCO_CLKCTLST_HWCROFF 0x00000020 /* Force HW clock request off */
197 #define SSB_CHIPCO_CLKCTLST_HAVEALP 0x00010000 /* ALP available */
198 #define SSB_CHIPCO_CLKCTLST_HAVEHT 0x00020000 /* HT available */
199 #define SSB_CHIPCO_CLKCTLST_4328A0_HAVEHT 0x00010000 /* 4328a0 has reversed bits */
200 #define SSB_CHIPCO_CLKCTLST_4328A0_HAVEALP 0x00020000 /* 4328a0 has reversed bits */
201 #define SSB_CHIPCO_HW_WORKAROUND 0x01E4 /* Hardware workaround (rev >= 20) */
202 #define SSB_CHIPCO_UART0_DATA 0x0300
203 #define SSB_CHIPCO_UART0_IMR 0x0304
204 #define SSB_CHIPCO_UART0_FCR 0x0308
205 #define SSB_CHIPCO_UART0_LCR 0x030C
206 #define SSB_CHIPCO_UART0_MCR 0x0310
207 #define SSB_CHIPCO_UART0_LSR 0x0314
208 #define SSB_CHIPCO_UART0_MSR 0x0318
209 #define SSB_CHIPCO_UART0_SCRATCH 0x031C
210 #define SSB_CHIPCO_UART1_DATA 0x0400
211 #define SSB_CHIPCO_UART1_IMR 0x0404
212 #define SSB_CHIPCO_UART1_FCR 0x0408
213 #define SSB_CHIPCO_UART1_LCR 0x040C
214 #define SSB_CHIPCO_UART1_MCR 0x0410
215 #define SSB_CHIPCO_UART1_LSR 0x0414
216 #define SSB_CHIPCO_UART1_MSR 0x0418
217 #define SSB_CHIPCO_UART1_SCRATCH 0x041C
218 /* PMU registers (rev >= 20) */
219 #define SSB_CHIPCO_PMU_CTL 0x0600 /* PMU control */
220 #define SSB_CHIPCO_PMU_CTL_ILP_DIV 0xFFFF0000 /* ILP div mask */
221 #define SSB_CHIPCO_PMU_CTL_ILP_DIV_SHIFT 16
222 #define SSB_CHIPCO_PMU_CTL_PLL_UPD 0x00000400
223 #define SSB_CHIPCO_PMU_CTL_NOILPONW 0x00000200 /* No ILP on wait */
224 #define SSB_CHIPCO_PMU_CTL_HTREQEN 0x00000100 /* HT req enable */
225 #define SSB_CHIPCO_PMU_CTL_ALPREQEN 0x00000080 /* ALP req enable */
226 #define SSB_CHIPCO_PMU_CTL_XTALFREQ 0x0000007C /* Crystal freq */
227 #define SSB_CHIPCO_PMU_CTL_XTALFREQ_SHIFT 2
228 #define SSB_CHIPCO_PMU_CTL_ILPDIVEN 0x00000002 /* ILP div enable */
229 #define SSB_CHIPCO_PMU_CTL_LPOSEL 0x00000001 /* LPO sel */
230 #define SSB_CHIPCO_PMU_CAP 0x0604 /* PMU capabilities */
231 #define SSB_CHIPCO_PMU_CAP_REVISION 0x000000FF /* Revision mask */
232 #define SSB_CHIPCO_PMU_STAT 0x0608 /* PMU status */
233 #define SSB_CHIPCO_PMU_STAT_INTPEND 0x00000040 /* Interrupt pending */
234 #define SSB_CHIPCO_PMU_STAT_SBCLKST 0x00000030 /* Backplane clock status? */
235 #define SSB_CHIPCO_PMU_STAT_HAVEALP 0x00000008 /* ALP available */
236 #define SSB_CHIPCO_PMU_STAT_HAVEHT 0x00000004 /* HT available */
237 #define SSB_CHIPCO_PMU_STAT_RESINIT 0x00000003 /* Res init */
238 #define SSB_CHIPCO_PMU_RES_STAT 0x060C /* PMU res status */
239 #define SSB_CHIPCO_PMU_RES_PEND 0x0610 /* PMU res pending */
240 #define SSB_CHIPCO_PMU_TIMER 0x0614 /* PMU timer */
241 #define SSB_CHIPCO_PMU_MINRES_MSK 0x0618 /* PMU min res mask */
242 #define SSB_CHIPCO_PMU_MAXRES_MSK 0x061C /* PMU max res mask */
243 #define SSB_CHIPCO_PMU_RES_TABSEL 0x0620 /* PMU res table sel */
244 #define SSB_CHIPCO_PMU_RES_DEPMSK 0x0624 /* PMU res dep mask */
245 #define SSB_CHIPCO_PMU_RES_UPDNTM 0x0628 /* PMU res updown timer */
246 #define SSB_CHIPCO_PMU_RES_TIMER 0x062C /* PMU res timer */
247 #define SSB_CHIPCO_PMU_CLKSTRETCH 0x0630 /* PMU clockstretch */
248 #define SSB_CHIPCO_PMU_WATCHDOG 0x0634 /* PMU watchdog */
249 #define SSB_CHIPCO_PMU_RES_REQTS 0x0640 /* PMU res req timer sel */
250 #define SSB_CHIPCO_PMU_RES_REQT 0x0644 /* PMU res req timer */
251 #define SSB_CHIPCO_PMU_RES_REQM 0x0648 /* PMU res req mask */
252 #define SSB_CHIPCO_CHIPCTL_ADDR 0x0650
253 #define SSB_CHIPCO_CHIPCTL_DATA 0x0654
254 #define SSB_CHIPCO_REGCTL_ADDR 0x0658
255 #define SSB_CHIPCO_REGCTL_DATA 0x065C
256 #define SSB_CHIPCO_PLLCTL_ADDR 0x0660
257 #define SSB_CHIPCO_PLLCTL_DATA 0x0664
261 /** PMU PLL registers */
263 /* PMU rev 0 PLL registers */
264 #define SSB_PMU0_PLLCTL0 0
265 #define SSB_PMU0_PLLCTL0_PDIV_MSK 0x00000001
266 #define SSB_PMU0_PLLCTL0_PDIV_FREQ 25000 /* kHz */
267 #define SSB_PMU0_PLLCTL1 1
268 #define SSB_PMU0_PLLCTL1_WILD_IMSK 0xF0000000 /* Wild int mask (low nibble) */
269 #define SSB_PMU0_PLLCTL1_WILD_IMSK_SHIFT 28
270 #define SSB_PMU0_PLLCTL1_WILD_FMSK 0x0FFFFF00 /* Wild frac mask */
271 #define SSB_PMU0_PLLCTL1_WILD_FMSK_SHIFT 8
272 #define SSB_PMU0_PLLCTL1_STOPMOD 0x00000040 /* Stop mod */
273 #define SSB_PMU0_PLLCTL2 2
274 #define SSB_PMU0_PLLCTL2_WILD_IMSKHI 0x0000000F /* Wild int mask (high nibble) */
275 #define SSB_PMU0_PLLCTL2_WILD_IMSKHI_SHIFT 0
277 /* PMU rev 1 PLL registers */
278 #define SSB_PMU1_PLLCTL0 0
279 #define SSB_PMU1_PLLCTL0_P1DIV 0x00F00000 /* P1 div */
280 #define SSB_PMU1_PLLCTL0_P1DIV_SHIFT 20
281 #define SSB_PMU1_PLLCTL0_P2DIV 0x0F000000 /* P2 div */
282 #define SSB_PMU1_PLLCTL0_P2DIV_SHIFT 24
283 #define SSB_PMU1_PLLCTL1 1
284 #define SSB_PMU1_PLLCTL1_M1DIV 0x000000FF /* M1 div */
285 #define SSB_PMU1_PLLCTL1_M1DIV_SHIFT 0
286 #define SSB_PMU1_PLLCTL1_M2DIV 0x0000FF00 /* M2 div */
287 #define SSB_PMU1_PLLCTL1_M2DIV_SHIFT 8
288 #define SSB_PMU1_PLLCTL1_M3DIV 0x00FF0000 /* M3 div */
289 #define SSB_PMU1_PLLCTL1_M3DIV_SHIFT 16
290 #define SSB_PMU1_PLLCTL1_M4DIV 0xFF000000 /* M4 div */
291 #define SSB_PMU1_PLLCTL1_M4DIV_SHIFT 24
292 #define SSB_PMU1_PLLCTL2 2
293 #define SSB_PMU1_PLLCTL2_M5DIV 0x000000FF /* M5 div */
294 #define SSB_PMU1_PLLCTL2_M5DIV_SHIFT 0
295 #define SSB_PMU1_PLLCTL2_M6DIV 0x0000FF00 /* M6 div */
296 #define SSB_PMU1_PLLCTL2_M6DIV_SHIFT 8
297 #define SSB_PMU1_PLLCTL2_NDIVMODE 0x000E0000 /* NDIV mode */
298 #define SSB_PMU1_PLLCTL2_NDIVMODE_SHIFT 17
299 #define SSB_PMU1_PLLCTL2_NDIVINT 0x1FF00000 /* NDIV int */
300 #define SSB_PMU1_PLLCTL2_NDIVINT_SHIFT 20
301 #define SSB_PMU1_PLLCTL3 3
302 #define SSB_PMU1_PLLCTL3_NDIVFRAC 0x00FFFFFF /* NDIV frac */
303 #define SSB_PMU1_PLLCTL3_NDIVFRAC_SHIFT 0
304 #define SSB_PMU1_PLLCTL4 4
305 #define SSB_PMU1_PLLCTL5 5
306 #define SSB_PMU1_PLLCTL5_CLKDRV 0xFFFFFF00 /* clk drv */
307 #define SSB_PMU1_PLLCTL5_CLKDRV_SHIFT 8
309 /* BCM4312 PLL resource numbers. */
310 #define SSB_PMURES_4312_SWITCHER_BURST 0
311 #define SSB_PMURES_4312_SWITCHER_PWM 1
312 #define SSB_PMURES_4312_PA_REF_LDO 2
313 #define SSB_PMURES_4312_CORE_LDO_BURST 3
314 #define SSB_PMURES_4312_CORE_LDO_PWM 4
315 #define SSB_PMURES_4312_RADIO_LDO 5
316 #define SSB_PMURES_4312_ILP_REQUEST 6
317 #define SSB_PMURES_4312_BG_FILTBYP 7
318 #define SSB_PMURES_4312_TX_FILTBYP 8
319 #define SSB_PMURES_4312_RX_FILTBYP 9
320 #define SSB_PMURES_4312_XTAL_PU 10
321 #define SSB_PMURES_4312_ALP_AVAIL 11
322 #define SSB_PMURES_4312_BB_PLL_FILTBYP 12
323 #define SSB_PMURES_4312_RF_PLL_FILTBYP 13
324 #define SSB_PMURES_4312_HT_AVAIL 14
326 /* BCM4325 PLL resource numbers. */
327 #define SSB_PMURES_4325_BUCK_BOOST_BURST 0
328 #define SSB_PMURES_4325_CBUCK_BURST 1
329 #define SSB_PMURES_4325_CBUCK_PWM 2
330 #define SSB_PMURES_4325_CLDO_CBUCK_BURST 3
331 #define SSB_PMURES_4325_CLDO_CBUCK_PWM 4
332 #define SSB_PMURES_4325_BUCK_BOOST_PWM 5
333 #define SSB_PMURES_4325_ILP_REQUEST 6
334 #define SSB_PMURES_4325_ABUCK_BURST 7
335 #define SSB_PMURES_4325_ABUCK_PWM 8
336 #define SSB_PMURES_4325_LNLDO1_PU 9
337 #define SSB_PMURES_4325_LNLDO2_PU 10
338 #define SSB_PMURES_4325_LNLDO3_PU 11
339 #define SSB_PMURES_4325_LNLDO4_PU 12
340 #define SSB_PMURES_4325_XTAL_PU 13
341 #define SSB_PMURES_4325_ALP_AVAIL 14
342 #define SSB_PMURES_4325_RX_PWRSW_PU 15
343 #define SSB_PMURES_4325_TX_PWRSW_PU 16
344 #define SSB_PMURES_4325_RFPLL_PWRSW_PU 17
345 #define SSB_PMURES_4325_LOGEN_PWRSW_PU 18
346 #define SSB_PMURES_4325_AFE_PWRSW_PU 19
347 #define SSB_PMURES_4325_BBPLL_PWRSW_PU 20
348 #define SSB_PMURES_4325_HT_AVAIL 21
350 /* BCM4328 PLL resource numbers. */
351 #define SSB_PMURES_4328_EXT_SWITCHER_PWM 0
352 #define SSB_PMURES_4328_BB_SWITCHER_PWM 1
353 #define SSB_PMURES_4328_BB_SWITCHER_BURST 2
354 #define SSB_PMURES_4328_BB_EXT_SWITCHER_BURST 3
355 #define SSB_PMURES_4328_ILP_REQUEST 4
356 #define SSB_PMURES_4328_RADIO_SWITCHER_PWM 5
357 #define SSB_PMURES_4328_RADIO_SWITCHER_BURST 6
358 #define SSB_PMURES_4328_ROM_SWITCH 7
359 #define SSB_PMURES_4328_PA_REF_LDO 8
360 #define SSB_PMURES_4328_RADIO_LDO 9
361 #define SSB_PMURES_4328_AFE_LDO 10
362 #define SSB_PMURES_4328_PLL_LDO 11
363 #define SSB_PMURES_4328_BG_FILTBYP 12
364 #define SSB_PMURES_4328_TX_FILTBYP 13
365 #define SSB_PMURES_4328_RX_FILTBYP 14
366 #define SSB_PMURES_4328_XTAL_PU 15
367 #define SSB_PMURES_4328_XTAL_EN 16
368 #define SSB_PMURES_4328_BB_PLL_FILTBYP 17
369 #define SSB_PMURES_4328_RF_PLL_FILTBYP 18
370 #define SSB_PMURES_4328_BB_PLL_PU 19
372 /* BCM5354 PLL resource numbers. */
373 #define SSB_PMURES_5354_EXT_SWITCHER_PWM 0
374 #define SSB_PMURES_5354_BB_SWITCHER_PWM 1
375 #define SSB_PMURES_5354_BB_SWITCHER_BURST 2
376 #define SSB_PMURES_5354_BB_EXT_SWITCHER_BURST 3
377 #define SSB_PMURES_5354_ILP_REQUEST 4
378 #define SSB_PMURES_5354_RADIO_SWITCHER_PWM 5
379 #define SSB_PMURES_5354_RADIO_SWITCHER_BURST 6
380 #define SSB_PMURES_5354_ROM_SWITCH 7
381 #define SSB_PMURES_5354_PA_REF_LDO 8
382 #define SSB_PMURES_5354_RADIO_LDO 9
383 #define SSB_PMURES_5354_AFE_LDO 10
384 #define SSB_PMURES_5354_PLL_LDO 11
385 #define SSB_PMURES_5354_BG_FILTBYP 12
386 #define SSB_PMURES_5354_TX_FILTBYP 13
387 #define SSB_PMURES_5354_RX_FILTBYP 14
388 #define SSB_PMURES_5354_XTAL_PU 15
389 #define SSB_PMURES_5354_XTAL_EN 16
390 #define SSB_PMURES_5354_BB_PLL_FILTBYP 17
391 #define SSB_PMURES_5354_RF_PLL_FILTBYP 18
392 #define SSB_PMURES_5354_BB_PLL_PU 19
396 /** Chip specific Chip-Status register contents. */
397 #define SSB_CHIPCO_CHST_4322_SPROM_EXISTS 0x00000040 /* SPROM present */
398 #define SSB_CHIPCO_CHST_4325_SPROM_OTP_SEL 0x00000003
399 #define SSB_CHIPCO_CHST_4325_DEFCIS_SEL 0 /* OTP is powered up, use def. CIS, no SPROM */
400 #define SSB_CHIPCO_CHST_4325_SPROM_SEL 1 /* OTP is powered up, SPROM is present */
401 #define SSB_CHIPCO_CHST_4325_OTP_SEL 2 /* OTP is powered up, no SPROM */
402 #define SSB_CHIPCO_CHST_4325_OTP_PWRDN 3 /* OTP is powered down, SPROM is present */
403 #define SSB_CHIPCO_CHST_4325_SDIO_USB_MODE 0x00000004
404 #define SSB_CHIPCO_CHST_4325_SDIO_USB_MODE_SHIFT 2
405 #define SSB_CHIPCO_CHST_4325_RCAL_VALID 0x00000008
406 #define SSB_CHIPCO_CHST_4325_RCAL_VALID_SHIFT 3
407 #define SSB_CHIPCO_CHST_4325_RCAL_VALUE 0x000001F0
408 #define SSB_CHIPCO_CHST_4325_RCAL_VALUE_SHIFT 4
409 #define SSB_CHIPCO_CHST_4325_PMUTOP_2B 0x00000200 /* 1 for 2b, 0 for to 2a */
411 /** Macros to determine SPROM presence based on Chip-Status register. */
412 #define SSB_CHIPCO_CHST_4312_SPROM_PRESENT(status) \
413 ((status & SSB_CHIPCO_CHST_4325_SPROM_OTP_SEL) != \
414 SSB_CHIPCO_CHST_4325_OTP_SEL)
415 #define SSB_CHIPCO_CHST_4322_SPROM_PRESENT(status) \
416 (status & SSB_CHIPCO_CHST_4322_SPROM_EXISTS)
417 #define SSB_CHIPCO_CHST_4325_SPROM_PRESENT(status) \
418 (((status & SSB_CHIPCO_CHST_4325_SPROM_OTP_SEL) != \
419 SSB_CHIPCO_CHST_4325_DEFCIS_SEL) && \
420 ((status & SSB_CHIPCO_CHST_4325_SPROM_OTP_SEL) != \
421 SSB_CHIPCO_CHST_4325_OTP_SEL))
425 /** Clockcontrol masks and values **/
427 /* SSB_CHIPCO_CLOCK_N */
428 #define SSB_CHIPCO_CLK_N1 0x0000003F /* n1 control */
429 #define SSB_CHIPCO_CLK_N2 0x00003F00 /* n2 control */
430 #define SSB_CHIPCO_CLK_N2_SHIFT 8
431 #define SSB_CHIPCO_CLK_PLLC 0x000F0000 /* pll control */
432 #define SSB_CHIPCO_CLK_PLLC_SHIFT 16
434 /* SSB_CHIPCO_CLOCK_SB/PCI/UART */
435 #define SSB_CHIPCO_CLK_M1 0x0000003F /* m1 control */
436 #define SSB_CHIPCO_CLK_M2 0x00003F00 /* m2 control */
437 #define SSB_CHIPCO_CLK_M2_SHIFT 8
438 #define SSB_CHIPCO_CLK_M3 0x003F0000 /* m3 control */
439 #define SSB_CHIPCO_CLK_M3_SHIFT 16
440 #define SSB_CHIPCO_CLK_MC 0x1F000000 /* mux control */
441 #define SSB_CHIPCO_CLK_MC_SHIFT 24
443 /* N3M Clock control magic field values */
444 #define SSB_CHIPCO_CLK_F6_2 0x02 /* A factor of 2 in */
445 #define SSB_CHIPCO_CLK_F6_3 0x03 /* 6-bit fields like */
446 #define SSB_CHIPCO_CLK_F6_4 0x05 /* N1, M1 or M3 */
447 #define SSB_CHIPCO_CLK_F6_5 0x09
448 #define SSB_CHIPCO_CLK_F6_6 0x11
449 #define SSB_CHIPCO_CLK_F6_7 0x21
451 #define SSB_CHIPCO_CLK_F5_BIAS 5 /* 5-bit fields get this added */
453 #define SSB_CHIPCO_CLK_MC_BYPASS 0x08
454 #define SSB_CHIPCO_CLK_MC_M1 0x04
455 #define SSB_CHIPCO_CLK_MC_M1M2 0x02
456 #define SSB_CHIPCO_CLK_MC_M1M2M3 0x01
457 #define SSB_CHIPCO_CLK_MC_M1M3 0x11
459 /* Type 2 Clock control magic field values */
460 #define SSB_CHIPCO_CLK_T2_BIAS 2 /* n1, n2, m1 & m3 bias */
461 #define SSB_CHIPCO_CLK_T2M2_BIAS 3 /* m2 bias */
463 #define SSB_CHIPCO_CLK_T2MC_M1BYP 1
464 #define SSB_CHIPCO_CLK_T2MC_M2BYP 2
465 #define SSB_CHIPCO_CLK_T2MC_M3BYP 4
467 /* Type 6 Clock control magic field values */
468 #define SSB_CHIPCO_CLK_T6_MMASK 1 /* bits of interest in m */
469 #define SSB_CHIPCO_CLK_T6_M0 120000000 /* sb clock for m = 0 */
470 #define SSB_CHIPCO_CLK_T6_M1 100000000 /* sb clock for m = 1 */
471 #define SSB_CHIPCO_CLK_SB2MIPS_T6(sb) (2 * (sb))
473 /* Common clock base */
474 #define SSB_CHIPCO_CLK_BASE1 24000000 /* Half the clock freq */
475 #define SSB_CHIPCO_CLK_BASE2 12500000 /* Alternate crystal on some PLL's */
477 /* Clock control values for 200Mhz in 5350 */
478 #define SSB_CHIPCO_CLK_5350_N 0x0311
479 #define SSB_CHIPCO_CLK_5350_M 0x04020009
482 /** Bits in the config registers **/
484 #define SSB_CHIPCO_CFG_EN 0x0001 /* Enable */
485 #define SSB_CHIPCO_CFG_EXTM 0x000E /* Extif Mode */
486 #define SSB_CHIPCO_CFG_EXTM_ASYNC 0x0002 /* Async/Parallel flash */
487 #define SSB_CHIPCO_CFG_EXTM_SYNC 0x0004 /* Synchronous */
488 #define SSB_CHIPCO_CFG_EXTM_PCMCIA 0x0008 /* PCMCIA */
489 #define SSB_CHIPCO_CFG_EXTM_IDE 0x000A /* IDE */
490 #define SSB_CHIPCO_CFG_DS16 0x0010 /* Data size, 0=8bit, 1=16bit */
491 #define SSB_CHIPCO_CFG_CLKDIV 0x0060 /* Sync: Clock divisor */
492 #define SSB_CHIPCO_CFG_CLKEN 0x0080 /* Sync: Clock enable */
493 #define SSB_CHIPCO_CFG_BSTRO 0x0100 /* Sync: Size/Bytestrobe */
496 /** Flash-specific control/status values */
498 /* flashcontrol opcodes for ST flashes */
499 #define SSB_CHIPCO_FLASHCTL_ST_WREN 0x0006 /* Write Enable */
500 #define SSB_CHIPCO_FLASHCTL_ST_WRDIS 0x0004 /* Write Disable */
501 #define SSB_CHIPCO_FLASHCTL_ST_RDSR 0x0105 /* Read Status Register */
502 #define SSB_CHIPCO_FLASHCTL_ST_WRSR 0x0101 /* Write Status Register */
503 #define SSB_CHIPCO_FLASHCTL_ST_READ 0x0303 /* Read Data Bytes */
504 #define SSB_CHIPCO_FLASHCTL_ST_PP 0x0302 /* Page Program */
505 #define SSB_CHIPCO_FLASHCTL_ST_SE 0x02D8 /* Sector Erase */
506 #define SSB_CHIPCO_FLASHCTL_ST_BE 0x00C7 /* Bulk Erase */
507 #define SSB_CHIPCO_FLASHCTL_ST_DP 0x00B9 /* Deep Power-down */
508 #define SSB_CHIPCO_FLASHCTL_ST_RES 0x03AB /* Read Electronic Signature */
509 #define SSB_CHIPCO_FLASHCTL_ST_CSA 0x1000 /* Keep chip select asserted */
510 #define SSB_CHIPCO_FLASHCTL_ST_SSE 0x0220 /* Sub-sector Erase */
512 /* Status register bits for ST flashes */
513 #define SSB_CHIPCO_FLASHSTA_ST_WIP 0x01 /* Write In Progress */
514 #define SSB_CHIPCO_FLASHSTA_ST_WEL 0x02 /* Write Enable Latch */
515 #define SSB_CHIPCO_FLASHSTA_ST_BP 0x1C /* Block Protect */
516 #define SSB_CHIPCO_FLASHSTA_ST_BP_SHIFT 2
517 #define SSB_CHIPCO_FLASHSTA_ST_SRWD 0x80 /* Status Register Write Disable */
519 /* flashcontrol opcodes for Atmel flashes */
520 #define SSB_CHIPCO_FLASHCTL_AT_READ 0x07E8
521 #define SSB_CHIPCO_FLASHCTL_AT_PAGE_READ 0x07D2
522 #define SSB_CHIPCO_FLASHCTL_AT_BUF1_READ /* FIXME */
523 #define SSB_CHIPCO_FLASHCTL_AT_BUF2_READ /* FIXME */
524 #define SSB_CHIPCO_FLASHCTL_AT_STATUS 0x01D7
525 #define SSB_CHIPCO_FLASHCTL_AT_BUF1_WRITE 0x0384
526 #define SSB_CHIPCO_FLASHCTL_AT_BUF2_WRITE 0x0387
527 #define SSB_CHIPCO_FLASHCTL_AT_BUF1_ERASE_PRGM 0x0283 /* Erase program */
528 #define SSB_CHIPCO_FLASHCTL_AT_BUF2_ERASE_PRGM 0x0286 /* Erase program */
529 #define SSB_CHIPCO_FLASHCTL_AT_BUF1_PROGRAM 0x0288
530 #define SSB_CHIPCO_FLASHCTL_AT_BUF2_PROGRAM 0x0289
531 #define SSB_CHIPCO_FLASHCTL_AT_PAGE_ERASE 0x0281
532 #define SSB_CHIPCO_FLASHCTL_AT_BLOCK_ERASE 0x0250
533 #define SSB_CHIPCO_FLASHCTL_AT_BUF1_WRER_PRGM 0x0382 /* Write erase program */
534 #define SSB_CHIPCO_FLASHCTL_AT_BUF2_WRER_PRGM 0x0385 /* Write erase program */
535 #define SSB_CHIPCO_FLASHCTL_AT_BUF1_LOAD 0x0253
536 #define SSB_CHIPCO_FLASHCTL_AT_BUF2_LOAD 0x0255
537 #define SSB_CHIPCO_FLASHCTL_AT_BUF1_COMPARE 0x0260
538 #define SSB_CHIPCO_FLASHCTL_AT_BUF2_COMPARE 0x0261
539 #define SSB_CHIPCO_FLASHCTL_AT_BUF1_REPROGRAM 0x0258
540 #define SSB_CHIPCO_FLASHCTL_AT_BUF2_REPROGRAM 0x0259
542 /* Status register bits for Atmel flashes */
543 #define SSB_CHIPCO_FLASHSTA_AT_READY 0x80
544 #define SSB_CHIPCO_FLASHSTA_AT_MISMATCH 0x40
545 #define SSB_CHIPCO_FLASHSTA_AT_ID 0x38
546 #define SSB_CHIPCO_FLASHSTA_AT_ID_SHIFT 3
552 #define SSB_CHIPCO_OTP_HW_REGION SSB_CHIPCO_OTPS_HW_PROTECT
553 #define SSB_CHIPCO_OTP_SW_REGION SSB_CHIPCO_OTPS_SW_PROTECT
554 #define SSB_CHIPCO_OTP_CID_REGION SSB_CHIPCO_OTPS_CID_PROTECT
556 /* OTP regions (Byte offsets from otp size) */
557 #define SSB_CHIPCO_OTP_SWLIM_OFF (-8)
558 #define SSB_CHIPCO_OTP_CIDBASE_OFF 0
559 #define SSB_CHIPCO_OTP_CIDLIM_OFF 8
561 /* Predefined OTP words (Word offset from otp size) */
562 #define SSB_CHIPCO_OTP_BOUNDARY_OFF (-4)
563 #define SSB_CHIPCO_OTP_HWSIGN_OFF (-3)
564 #define SSB_CHIPCO_OTP_SWSIGN_OFF (-2)
565 #define SSB_CHIPCO_OTP_CIDSIGN_OFF (-1)
567 #define SSB_CHIPCO_OTP_CID_OFF 0
568 #define SSB_CHIPCO_OTP_PKG_OFF 1
569 #define SSB_CHIPCO_OTP_FID_OFF 2
570 #define SSB_CHIPCO_OTP_RSV_OFF 3
571 #define SSB_CHIPCO_OTP_LIM_OFF 4
573 #define SSB_CHIPCO_OTP_SIGNATURE 0x578A
574 #define SSB_CHIPCO_OTP_MAGIC 0x4E56
578 struct ssb_serial_port;
580 /* Data for the PMU, if available.
581 * Check availability with ((struct ssb_chipcommon)->capabilities & SSB_CHIPCO_CAP_PMU)
583 struct ssb_chipcommon_pmu {
584 u8 rev; /* PMU revision */
585 u32 crystalfreq; /* The active crystal frequency (in kHz) */
588 struct ssb_chipcommon {
589 struct ssb_device *dev;
592 /* Fast Powerup Delay constant */
593 u16 fast_pwrup_delay;
594 spinlock_t gpio_lock;
595 struct ssb_chipcommon_pmu pmu;
600 static inline bool ssb_chipco_available(struct ssb_chipcommon *cc)
602 return (cc->dev != NULL);
605 /* Register access */
606 #define chipco_read32(cc, offset) ssb_read32((cc)->dev, offset)
607 #define chipco_write32(cc, offset, val) ssb_write32((cc)->dev, offset, val)
609 #define chipco_mask32(cc, offset, mask) \
610 chipco_write32(cc, offset, chipco_read32(cc, offset) & (mask))
611 #define chipco_set32(cc, offset, set) \
612 chipco_write32(cc, offset, chipco_read32(cc, offset) | (set))
613 #define chipco_maskset32(cc, offset, mask, set) \
614 chipco_write32(cc, offset, (chipco_read32(cc, offset) & (mask)) | (set))
616 extern void ssb_chipcommon_init(struct ssb_chipcommon *cc);
618 extern void ssb_chipco_suspend(struct ssb_chipcommon *cc);
619 extern void ssb_chipco_resume(struct ssb_chipcommon *cc);
621 extern void ssb_chipco_get_clockcpu(struct ssb_chipcommon *cc,
622 u32 *plltype, u32 *n, u32 *m);
623 extern void ssb_chipco_get_clockcontrol(struct ssb_chipcommon *cc,
624 u32 *plltype, u32 *n, u32 *m);
625 extern void ssb_chipco_timing_init(struct ssb_chipcommon *cc,
626 unsigned long ns_per_cycle);
634 extern void ssb_chipco_set_clockmode(struct ssb_chipcommon *cc,
635 enum ssb_clkmode mode);
637 extern u32 ssb_chipco_watchdog_timer_set(struct ssb_chipcommon *cc, u32 ticks);
639 void ssb_chipco_irq_mask(struct ssb_chipcommon *cc, u32 mask, u32 value);
641 u32 ssb_chipco_irq_status(struct ssb_chipcommon *cc, u32 mask);
643 /* Chipcommon GPIO pin access. */
644 u32 ssb_chipco_gpio_in(struct ssb_chipcommon *cc, u32 mask);
645 u32 ssb_chipco_gpio_out(struct ssb_chipcommon *cc, u32 mask, u32 value);
646 u32 ssb_chipco_gpio_outen(struct ssb_chipcommon *cc, u32 mask, u32 value);
647 u32 ssb_chipco_gpio_control(struct ssb_chipcommon *cc, u32 mask, u32 value);
648 u32 ssb_chipco_gpio_intmask(struct ssb_chipcommon *cc, u32 mask, u32 value);
649 u32 ssb_chipco_gpio_polarity(struct ssb_chipcommon *cc, u32 mask, u32 value);
650 u32 ssb_chipco_gpio_pullup(struct ssb_chipcommon *cc, u32 mask, u32 value);
651 u32 ssb_chipco_gpio_pulldown(struct ssb_chipcommon *cc, u32 mask, u32 value);
653 #ifdef CONFIG_SSB_SERIAL
654 extern int ssb_chipco_serial_init(struct ssb_chipcommon *cc,
655 struct ssb_serial_port *ports);
656 #endif /* CONFIG_SSB_SERIAL */
659 extern void ssb_pmu_init(struct ssb_chipcommon *cc);
661 enum ssb_pmu_ldo_volt_id {
668 void ssb_pmu_set_ldo_voltage(struct ssb_chipcommon *cc,
669 enum ssb_pmu_ldo_volt_id id, u32 voltage);
670 void ssb_pmu_set_ldo_paref(struct ssb_chipcommon *cc, bool on);
671 void ssb_pmu_spuravoid_pllupdate(struct ssb_chipcommon *cc, int spuravoid);
673 #endif /* LINUX_SSB_CHIPCO_H_ */
Code Review / kvmfornfv.git / blob