kernel/drivers/tty/serial/zs.c

   1 /*
   2  * zs.c: Serial port driver for IOASIC DECstations.
   3  *
   4  * Derived from drivers/sbus/char/sunserial.c by Paul Mackerras.
   5  * Derived from drivers/macintosh/macserial.c by Harald Koerfgen.
   6  *
   7  * DECstation changes
   8  * Copyright (C) 1998-2000 Harald Koerfgen
   9  * Copyright (C) 2000, 2001, 2002, 2003, 2004, 2005, 2007  Maciej W. Rozycki
  10  *
  11  * For the rest of the code the original Copyright applies:
  12  * Copyright (C) 1996 Paul Mackerras (Paul.Mackerras@cs.anu.edu.au)
  13  * Copyright (C) 1995 David S. Miller (davem@caip.rutgers.edu)
  14  *
  15  *
  16  * Note: for IOASIC systems the wiring is as follows:
  17  *
  18  * mouse/keyboard:
  19  * DIN-7 MJ-4  signal        SCC
  20  * 2     1     TxD       <-  A.TxD
  21  * 3     4     RxD       ->  A.RxD
  22  *
  23  * EIA-232/EIA-423:
  24  * DB-25 MMJ-6 signal        SCC
  25  * 2     2     TxD       <-  B.TxD
  26  * 3     5     RxD       ->  B.RxD
  27  * 4           RTS       <- ~A.RTS
  28  * 5           CTS       -> ~B.CTS
  29  * 6     6     DSR       -> ~A.SYNC
  30  * 8           CD        -> ~B.DCD
  31  * 12          DSRS(DCE) -> ~A.CTS  (*)
  32  * 15          TxC       ->  B.TxC
  33  * 17          RxC       ->  B.RxC
  34  * 20    1     DTR       <- ~A.DTR
  35  * 22          RI        -> ~A.DCD
  36  * 23          DSRS(DTE) <- ~B.RTS
  37  *
  38  * (*) EIA-232 defines the signal at this pin to be SCD, while DSRS(DCE)
  39  *     is shared with DSRS(DTE) at pin 23.
  40  *
  41  * As you can immediately notice the wiring of the RTS, DTR and DSR signals
  42  * is a bit odd.  This makes the handling of port B unnecessarily
  43  * complicated and prevents the use of some automatic modes of operation.
  44  */
  45
  46 #if defined(CONFIG_SERIAL_ZS_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
  47 #define SUPPORT_SYSRQ
  48 #endif
  49
  50 #include <linux/bug.h>
  51 #include <linux/console.h>
  52 #include <linux/delay.h>
  53 #include <linux/errno.h>
  54 #include <linux/init.h>
  55 #include <linux/interrupt.h>
  56 #include <linux/io.h>
  57 #include <linux/ioport.h>
  58 #include <linux/irqflags.h>
  59 #include <linux/kernel.h>
  60 #include <linux/module.h>
  61 #include <linux/major.h>
  62 #include <linux/serial.h>
  63 #include <linux/serial_core.h>
  64 #include <linux/spinlock.h>
  65 #include <linux/sysrq.h>
  66 #include <linux/tty.h>
  67 #include <linux/tty_flip.h>
  68 #include <linux/types.h>
  69
  70 #include <linux/atomic.h>
  71
  72 #include <asm/dec/interrupts.h>
  73 #include <asm/dec/ioasic_addrs.h>
  74 #include <asm/dec/system.h>
  75
  76 #include "zs.h"
  77
  78
  79 MODULE_AUTHOR("Maciej W. Rozycki <macro@linux-mips.org>");
  80 MODULE_DESCRIPTION("DECstation Z85C30 serial driver");
  81 MODULE_LICENSE("GPL");
  82
  83
  84 static char zs_name[] __initdata = "DECstation Z85C30 serial driver version ";
  85 static char zs_version[] __initdata = "0.10";
  86
  87 /*
  88  * It would be nice to dynamically allocate everything that
  89  * depends on ZS_NUM_SCCS, so we could support any number of
  90  * Z85C30s, but for now...
  91  */
  92 #define ZS_NUM_SCCS     2               /* Max # of ZS chips supported.  */
  93 #define ZS_NUM_CHAN     2               /* 2 channels per chip.  */
  94 #define ZS_CHAN_A       0               /* Index of the channel A.  */
  95 #define ZS_CHAN_B       1               /* Index of the channel B.  */
  96 #define ZS_CHAN_IO_SIZE 8               /* IOMEM space size.  */
  97 #define ZS_CHAN_IO_STRIDE 4             /* Register alignment.  */
  98 #define ZS_CHAN_IO_OFFSET 1             /* The SCC resides on the high byte
  99                                            of the 16-bit IOBUS.  */
 100 #define ZS_CLOCK        7372800         /* Z85C30 PCLK input clock rate.  */
 101
 102 #define to_zport(uport) container_of(uport, struct zs_port, port)
 103
 104 struct zs_parms {
 105         resource_size_t scc[ZS_NUM_SCCS];
 106         int irq[ZS_NUM_SCCS];
 107 };
 108
 109 static struct zs_scc zs_sccs[ZS_NUM_SCCS];
 110
 111 static u8 zs_init_regs[ZS_NUM_REGS] __initdata = {
 112         0,                              /* write 0 */
 113         PAR_SPEC,                       /* write 1 */
 114         0,                              /* write 2 */
 115         0,                              /* write 3 */
 116         X16CLK | SB1,                   /* write 4 */
 117         0,                              /* write 5 */
 118         0, 0, 0,                        /* write 6, 7, 8 */
 119         MIE | DLC | NV,                 /* write 9 */
 120         NRZ,                            /* write 10 */
 121         TCBR | RCBR,                    /* write 11 */
 122         0, 0,                           /* BRG time constant, write 12 + 13 */
 123         BRSRC | BRENABL,                /* write 14 */
 124         0,                              /* write 15 */
 125 };
 126
 127 /*
 128  * Debugging.
 129  */
 130 #undef ZS_DEBUG_REGS
 131
 132
 133 /*
 134  * Reading and writing Z85C30 registers.
 135  */
 136 static void recovery_delay(void)
 137 {
 138         udelay(2);
 139 }
 140
 141 static u8 read_zsreg(struct zs_port *zport, int reg)
 142 {
 143         void __iomem *control = zport->port.membase + ZS_CHAN_IO_OFFSET;
 144         u8 retval;
 145
 146         if (reg != 0) {
 147                 writeb(reg & 0xf, control);
 148                 fast_iob();
 149                 recovery_delay();
 150         }
 151         retval = readb(control);
 152         recovery_delay();
 153         return retval;
 154 }
 155
 156 static void write_zsreg(struct zs_port *zport, int reg, u8 value)
 157 {
 158         void __iomem *control = zport->port.membase + ZS_CHAN_IO_OFFSET;
 159
 160         if (reg != 0) {
 161                 writeb(reg & 0xf, control);
 162                 fast_iob(); recovery_delay();
 163         }
 164         writeb(value, control);
 165         fast_iob();
 166         recovery_delay();
 167         return;
 168 }
 169
 170 static u8 read_zsdata(struct zs_port *zport)
 171 {
 172         void __iomem *data = zport->port.membase +
 173                              ZS_CHAN_IO_STRIDE + ZS_CHAN_IO_OFFSET;
 174         u8 retval;
 175
 176         retval = readb(data);
 177         recovery_delay();
 178         return retval;
 179 }
 180
 181 static void write_zsdata(struct zs_port *zport, u8 value)
 182 {
 183         void __iomem *data = zport->port.membase +
 184                              ZS_CHAN_IO_STRIDE + ZS_CHAN_IO_OFFSET;
 185
 186         writeb(value, data);
 187         fast_iob();
 188         recovery_delay();
 189         return;
 190 }
 191
 192 #ifdef ZS_DEBUG_REGS
 193 void zs_dump(void)
 194 {
 195         struct zs_port *zport;
 196         int i, j;
 197
 198         for (i = 0; i < ZS_NUM_SCCS * ZS_NUM_CHAN; i++) {
 199                 zport = &zs_sccs[i / ZS_NUM_CHAN].zport[i % ZS_NUM_CHAN];
 200
 201                 if (!zport->scc)
 202                         continue;
 203
 204                 for (j = 0; j < 16; j++)
 205                         printk("W%-2d = 0x%02x\t", j, zport->regs[j]);
 206                 printk("\n");
 207                 for (j = 0; j < 16; j++)
 208                         printk("R%-2d = 0x%02x\t", j, read_zsreg(zport, j));
 209                 printk("\n\n");
 210         }
 211 }
 212 #endif
 213
 214
 215 static void zs_spin_lock_cond_irq(spinlock_t *lock, int irq)
 216 {
 217         if (irq)
 218                 spin_lock_irq(lock);
 219         else
 220                 spin_lock(lock);
 221 }
 222
 223 static void zs_spin_unlock_cond_irq(spinlock_t *lock, int irq)
 224 {
 225         if (irq)
 226                 spin_unlock_irq(lock);
 227         else
 228                 spin_unlock(lock);
 229 }
 230
 231 static int zs_receive_drain(struct zs_port *zport)
 232 {
 233         int loops = 10000;
 234
 235         while ((read_zsreg(zport, R0) & Rx_CH_AV) && --loops)
 236                 read_zsdata(zport);
 237         return loops;
 238 }
 239
 240 static int zs_transmit_drain(struct zs_port *zport, int irq)
 241 {
 242         struct zs_scc *scc = zport->scc;
 243         int loops = 10000;
 244
 245         while (!(read_zsreg(zport, R0) & Tx_BUF_EMP) && --loops) {
 246                 zs_spin_unlock_cond_irq(&scc->zlock, irq);
 247                 udelay(2);
 248                 zs_spin_lock_cond_irq(&scc->zlock, irq);
 249         }
 250         return loops;
 251 }
 252
 253 static int zs_line_drain(struct zs_port *zport, int irq)
 254 {
 255         struct zs_scc *scc = zport->scc;
 256         int loops = 10000;
 257
 258         while (!(read_zsreg(zport, R1) & ALL_SNT) && --loops) {
 259                 zs_spin_unlock_cond_irq(&scc->zlock, irq);
 260                 udelay(2);
 261                 zs_spin_lock_cond_irq(&scc->zlock, irq);
 262         }
 263         return loops;
 264 }
 265
 266
 267 static void load_zsregs(struct zs_port *zport, u8 *regs, int irq)
 268 {
 269         /* Let the current transmission finish.  */
 270         zs_line_drain(zport, irq);
 271         /* Load 'em up.  */
 272         write_zsreg(zport, R3, regs[3] & ~RxENABLE);
 273         write_zsreg(zport, R5, regs[5] & ~TxENAB);
 274         write_zsreg(zport, R4, regs[4]);
 275         write_zsreg(zport, R9, regs[9]);
 276         write_zsreg(zport, R1, regs[1]);
 277         write_zsreg(zport, R2, regs[2]);
 278         write_zsreg(zport, R10, regs[10]);
 279         write_zsreg(zport, R14, regs[14] & ~BRENABL);
 280         write_zsreg(zport, R11, regs[11]);
 281         write_zsreg(zport, R12, regs[12]);
 282         write_zsreg(zport, R13, regs[13]);
 283         write_zsreg(zport, R14, regs[14]);
 284         write_zsreg(zport, R15, regs[15]);
 285         if (regs[3] & RxENABLE)
 286                 write_zsreg(zport, R3, regs[3]);
 287         if (regs[5] & TxENAB)
 288                 write_zsreg(zport, R5, regs[5]);
 289         return;
 290 }
 291
 292
 293 /*
 294  * Status handling routines.
 295  */
 296
 297 /*
 298  * zs_tx_empty() -- get the transmitter empty status
 299  *
 300  * Purpose: Let user call ioctl() to get info when the UART physically
 301  *          is emptied.  On bus types like RS485, the transmitter must
 302  *          release the bus after transmitting.  This must be done when
 303  *          the transmit shift register is empty, not be done when the
 304  *          transmit holding register is empty.  This functionality
 305  *          allows an RS485 driver to be written in user space.
 306  */
 307 static unsigned int zs_tx_empty(struct uart_port *uport)
 308 {
 309         struct zs_port *zport = to_zport(uport);
 310         struct zs_scc *scc = zport->scc;
 311         unsigned long flags;
 312         u8 status;
 313
 314         spin_lock_irqsave(&scc->zlock, flags);
 315         status = read_zsreg(zport, R1);
 316         spin_unlock_irqrestore(&scc->zlock, flags);
 317
 318         return status & ALL_SNT ? TIOCSER_TEMT : 0;
 319 }
 320
 321 static unsigned int zs_raw_get_ab_mctrl(struct zs_port *zport_a,
 322                                         struct zs_port *zport_b)
 323 {
 324         u8 status_a, status_b;
 325         unsigned int mctrl;
 326
 327         status_a = read_zsreg(zport_a, R0);
 328         status_b = read_zsreg(zport_b, R0);
 329
 330         mctrl = ((status_b & CTS) ? TIOCM_CTS : 0) |
 331                 ((status_b & DCD) ? TIOCM_CAR : 0) |
 332                 ((status_a & DCD) ? TIOCM_RNG : 0) |
 333                 ((status_a & SYNC_HUNT) ? TIOCM_DSR : 0);
 334
 335         return mctrl;
 336 }
 337
 338 static unsigned int zs_raw_get_mctrl(struct zs_port *zport)
 339 {
 340         struct zs_port *zport_a = &zport->scc->zport[ZS_CHAN_A];
 341
 342         return zport != zport_a ? zs_raw_get_ab_mctrl(zport_a, zport) : 0;
 343 }
 344
 345 static unsigned int zs_raw_xor_mctrl(struct zs_port *zport)
 346 {
 347         struct zs_port *zport_a = &zport->scc->zport[ZS_CHAN_A];
 348         unsigned int mmask, mctrl, delta;
 349         u8 mask_a, mask_b;
 350
 351         if (zport == zport_a)
 352                 return 0;
 353
 354         mask_a = zport_a->regs[15];
 355         mask_b = zport->regs[15];
 356
 357         mmask = ((mask_b & CTSIE) ? TIOCM_CTS : 0) |
 358                 ((mask_b & DCDIE) ? TIOCM_CAR : 0) |
 359                 ((mask_a & DCDIE) ? TIOCM_RNG : 0) |
 360                 ((mask_a & SYNCIE) ? TIOCM_DSR : 0);
 361
 362         mctrl = zport->mctrl;
 363         if (mmask) {
 364                 mctrl &= ~mmask;
 365                 mctrl |= zs_raw_get_ab_mctrl(zport_a, zport) & mmask;
 366         }
 367
 368         delta = mctrl ^ zport->mctrl;
 369         if (delta)
 370                 zport->mctrl = mctrl;
 371
 372         return delta;
 373 }
 374
 375 static unsigned int zs_get_mctrl(struct uart_port *uport)
 376 {
 377         struct zs_port *zport = to_zport(uport);
 378         struct zs_scc *scc = zport->scc;
 379         unsigned int mctrl;
 380
 381         spin_lock(&scc->zlock);
 382         mctrl = zs_raw_get_mctrl(zport);
 383         spin_unlock(&scc->zlock);
 384
 385         return mctrl;
 386 }
 387
 388 static void zs_set_mctrl(struct uart_port *uport, unsigned int mctrl)
 389 {
 390         struct zs_port *zport = to_zport(uport);
 391         struct zs_scc *scc = zport->scc;
 392         struct zs_port *zport_a = &scc->zport[ZS_CHAN_A];
 393         u8 oldloop, newloop;
 394
 395         spin_lock(&scc->zlock);
 396         if (zport != zport_a) {
 397                 if (mctrl & TIOCM_DTR)
 398                         zport_a->regs[5] |= DTR;
 399                 else
 400                         zport_a->regs[5] &= ~DTR;
 401                 if (mctrl & TIOCM_RTS)
 402                         zport_a->regs[5] |= RTS;
 403                 else
 404                         zport_a->regs[5] &= ~RTS;
 405                 write_zsreg(zport_a, R5, zport_a->regs[5]);
 406         }
 407
 408         /* Rarely modified, so don't poke at hardware unless necessary. */
 409         oldloop = zport->regs[14];
 410         newloop = oldloop;
 411         if (mctrl & TIOCM_LOOP)
 412                 newloop |= LOOPBAK;
 413         else
 414                 newloop &= ~LOOPBAK;
 415         if (newloop != oldloop) {
 416                 zport->regs[14] = newloop;
 417                 write_zsreg(zport, R14, zport->regs[14]);
 418         }
 419         spin_unlock(&scc->zlock);
 420 }
 421
 422 static void zs_raw_stop_tx(struct zs_port *zport)
 423 {
 424         write_zsreg(zport, R0, RES_Tx_P);
 425         zport->tx_stopped = 1;
 426 }
 427
 428 static void zs_stop_tx(struct uart_port *uport)
 429 {
 430         struct zs_port *zport = to_zport(uport);
 431         struct zs_scc *scc = zport->scc;
 432
 433         spin_lock(&scc->zlock);
 434         zs_raw_stop_tx(zport);
 435         spin_unlock(&scc->zlock);
 436 }
 437
 438 static void zs_raw_transmit_chars(struct zs_port *);
 439
 440 static void zs_start_tx(struct uart_port *uport)
 441 {
 442         struct zs_port *zport = to_zport(uport);
 443         struct zs_scc *scc = zport->scc;
 444
 445         spin_lock(&scc->zlock);
 446         if (zport->tx_stopped) {
 447                 zs_transmit_drain(zport, 0);
 448                 zport->tx_stopped = 0;
 449                 zs_raw_transmit_chars(zport);
 450         }
 451         spin_unlock(&scc->zlock);
 452 }
 453
 454 static void zs_stop_rx(struct uart_port *uport)
 455 {
 456         struct zs_port *zport = to_zport(uport);
 457         struct zs_scc *scc = zport->scc;
 458         struct zs_port *zport_a = &scc->zport[ZS_CHAN_A];
 459
 460         spin_lock(&scc->zlock);
 461         zport->regs[15] &= ~BRKIE;
 462         zport->regs[1] &= ~(RxINT_MASK | TxINT_ENAB);
 463         zport->regs[1] |= RxINT_DISAB;
 464
 465         if (zport != zport_a) {
 466                 /* A-side DCD tracks RI and SYNC tracks DSR.  */
 467                 zport_a->regs[15] &= ~(DCDIE | SYNCIE);
 468                 write_zsreg(zport_a, R15, zport_a->regs[15]);
 469                 if (!(zport_a->regs[15] & BRKIE)) {
 470                         zport_a->regs[1] &= ~EXT_INT_ENAB;
 471                         write_zsreg(zport_a, R1, zport_a->regs[1]);
 472                 }
 473
 474                 /* This-side DCD tracks DCD and CTS tracks CTS.  */
 475                 zport->regs[15] &= ~(DCDIE | CTSIE);
 476                 zport->regs[1] &= ~EXT_INT_ENAB;
 477         } else {
 478                 /* DCD tracks RI and SYNC tracks DSR for the B side.  */
 479                 if (!(zport->regs[15] & (DCDIE | SYNCIE)))
 480                         zport->regs[1] &= ~EXT_INT_ENAB;
 481         }
 482
 483         write_zsreg(zport, R15, zport->regs[15]);
 484         write_zsreg(zport, R1, zport->regs[1]);
 485         spin_unlock(&scc->zlock);
 486 }
 487
 488 static void zs_enable_ms(struct uart_port *uport)
 489 {
 490         struct zs_port *zport = to_zport(uport);
 491         struct zs_scc *scc = zport->scc;
 492         struct zs_port *zport_a = &scc->zport[ZS_CHAN_A];
 493
 494         if (zport == zport_a)
 495                 return;
 496
 497         spin_lock(&scc->zlock);
 498
 499         /* Clear Ext interrupts if not being handled already.  */
 500         if (!(zport_a->regs[1] & EXT_INT_ENAB))
 501                 write_zsreg(zport_a, R0, RES_EXT_INT);
 502
 503         /* A-side DCD tracks RI and SYNC tracks DSR.  */
 504         zport_a->regs[1] |= EXT_INT_ENAB;
 505         zport_a->regs[15] |= DCDIE | SYNCIE;
 506
 507         /* This-side DCD tracks DCD and CTS tracks CTS.  */
 508         zport->regs[15] |= DCDIE | CTSIE;
 509
 510         zs_raw_xor_mctrl(zport);
 511
 512         write_zsreg(zport_a, R1, zport_a->regs[1]);
 513         write_zsreg(zport_a, R15, zport_a->regs[15]);
 514         write_zsreg(zport, R15, zport->regs[15]);
 515         spin_unlock(&scc->zlock);
 516 }
 517
 518 static void zs_break_ctl(struct uart_port *uport, int break_state)
 519 {
 520         struct zs_port *zport = to_zport(uport);
 521         struct zs_scc *scc = zport->scc;
 522         unsigned long flags;
 523
 524         spin_lock_irqsave(&scc->zlock, flags);
 525         if (break_state == -1)
 526                 zport->regs[5] |= SND_BRK;
 527         else
 528                 zport->regs[5] &= ~SND_BRK;
 529         write_zsreg(zport, R5, zport->regs[5]);
 530         spin_unlock_irqrestore(&scc->zlock, flags);
 531 }
 532
 533
 534 /*
 535  * Interrupt handling routines.
 536  */
 537 #define Rx_BRK 0x0100                   /* BREAK event software flag.  */
 538 #define Rx_SYS 0x0200                   /* SysRq event software flag.  */
 539
 540 static void zs_receive_chars(struct zs_port *zport)
 541 {
 542         struct uart_port *uport = &zport->port;
 543         struct zs_scc *scc = zport->scc;
 544         struct uart_icount *icount;
 545         unsigned int avail, status, ch, flag;
 546         int count;
 547
 548         for (count = 16; count; count--) {
 549                 spin_lock(&scc->zlock);
 550                 avail = read_zsreg(zport, R0) & Rx_CH_AV;
 551                 spin_unlock(&scc->zlock);
 552                 if (!avail)
 553                         break;
 554
 555                 spin_lock(&scc->zlock);
 556                 status = read_zsreg(zport, R1) & (Rx_OVR | FRM_ERR | PAR_ERR);
 557                 ch = read_zsdata(zport);
 558                 spin_unlock(&scc->zlock);
 559
 560                 flag = TTY_NORMAL;
 561
 562                 icount = &uport->icount;
 563                 icount->rx++;
 564
 565                 /* Handle the null char got when BREAK is removed.  */
 566                 if (!ch)
 567                         status |= zport->tty_break;
 568                 if (unlikely(status &
 569                              (Rx_OVR | FRM_ERR | PAR_ERR | Rx_SYS | Rx_BRK))) {
 570                         zport->tty_break = 0;
 571
 572                         /* Reset the error indication.  */
 573                         if (status & (Rx_OVR | FRM_ERR | PAR_ERR)) {
 574                                 spin_lock(&scc->zlock);
 575                                 write_zsreg(zport, R0, ERR_RES);
 576                                 spin_unlock(&scc->zlock);
 577                         }
 578
 579                         if (status & (Rx_SYS | Rx_BRK)) {
 580                                 icount->brk++;
 581                                 /* SysRq discards the null char.  */
 582                                 if (status & Rx_SYS)
 583                                         continue;
 584                         } else if (status & FRM_ERR)
 585                                 icount->frame++;
 586                         else if (status & PAR_ERR)
 587                                 icount->parity++;
 588                         if (status & Rx_OVR)
 589                                 icount->overrun++;
 590
 591                         status &= uport->read_status_mask;
 592                         if (status & Rx_BRK)
 593                                 flag = TTY_BREAK;
 594                         else if (status & FRM_ERR)
 595                                 flag = TTY_FRAME;
 596                         else if (status & PAR_ERR)
 597                                 flag = TTY_PARITY;
 598                 }
 599
 600                 if (uart_handle_sysrq_char(uport, ch))
 601                         continue;
 602
 603                 uart_insert_char(uport, status, Rx_OVR, ch, flag);
 604         }
 605
 606         tty_flip_buffer_push(&uport->state->port);
 607 }
 608
 609 static void zs_raw_transmit_chars(struct zs_port *zport)
 610 {
 611         struct circ_buf *xmit = &zport->port.state->xmit;
 612
 613         /* XON/XOFF chars.  */
 614         if (zport->port.x_char) {
 615                 write_zsdata(zport, zport->port.x_char);
 616                 zport->port.icount.tx++;
 617                 zport->port.x_char = 0;
 618                 return;
 619         }
 620
 621         /* If nothing to do or stopped or hardware stopped.  */
 622         if (uart_circ_empty(xmit) || uart_tx_stopped(&zport->port)) {
 623                 zs_raw_stop_tx(zport);
 624                 return;
 625         }
 626
 627         /* Send char.  */
 628         write_zsdata(zport, xmit->buf[xmit->tail]);
 629         xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
 630         zport->port.icount.tx++;
 631
 632         if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
 633                 uart_write_wakeup(&zport->port);
 634
 635         /* Are we are done?  */
 636         if (uart_circ_empty(xmit))
 637                 zs_raw_stop_tx(zport);
 638 }
 639
 640 static void zs_transmit_chars(struct zs_port *zport)
 641 {
 642         struct zs_scc *scc = zport->scc;
 643
 644         spin_lock(&scc->zlock);
 645         zs_raw_transmit_chars(zport);
 646         spin_unlock(&scc->zlock);
 647 }
 648
 649 static void zs_status_handle(struct zs_port *zport, struct zs_port *zport_a)
 650 {
 651         struct uart_port *uport = &zport->port;
 652         struct zs_scc *scc = zport->scc;
 653         unsigned int delta;
 654         u8 status, brk;
 655
 656         spin_lock(&scc->zlock);
 657
 658         /* Get status from Read Register 0.  */
 659         status = read_zsreg(zport, R0);
 660
 661         if (zport->regs[15] & BRKIE) {
 662                 brk = status & BRK_ABRT;
 663                 if (brk && !zport->brk) {
 664                         spin_unlock(&scc->zlock);
 665                         if (uart_handle_break(uport))
 666                                 zport->tty_break = Rx_SYS;
 667                         else
 668                                 zport->tty_break = Rx_BRK;
 669                         spin_lock(&scc->zlock);
 670                 }
 671                 zport->brk = brk;
 672         }
 673
 674         if (zport != zport_a) {
 675                 delta = zs_raw_xor_mctrl(zport);
 676                 spin_unlock(&scc->zlock);
 677
 678                 if (delta & TIOCM_CTS)
 679                         uart_handle_cts_change(uport,
 680                                                zport->mctrl & TIOCM_CTS);
 681                 if (delta & TIOCM_CAR)
 682                         uart_handle_dcd_change(uport,
 683                                                zport->mctrl & TIOCM_CAR);
 684                 if (delta & TIOCM_RNG)
 685                         uport->icount.dsr++;
 686                 if (delta & TIOCM_DSR)
 687                         uport->icount.rng++;
 688
 689                 if (delta)
 690                         wake_up_interruptible(&uport->state->port.delta_msr_wait);
 691
 692                 spin_lock(&scc->zlock);
 693         }
 694
 695         /* Clear the status condition...  */
 696         write_zsreg(zport, R0, RES_EXT_INT);
 697
 698         spin_unlock(&scc->zlock);
 699 }
 700
 701 /*
 702  * This is the Z85C30 driver's generic interrupt routine.
 703  */
 704 static irqreturn_t zs_interrupt(int irq, void *dev_id)
 705 {
 706         struct zs_scc *scc = dev_id;
 707         struct zs_port *zport_a = &scc->zport[ZS_CHAN_A];
 708         struct zs_port *zport_b = &scc->zport[ZS_CHAN_B];
 709         irqreturn_t status = IRQ_NONE;
 710         u8 zs_intreg;
 711         int count;
 712
 713         /*
 714          * NOTE: The read register 3, which holds the irq status,
 715          *       does so for both channels on each chip.  Although
 716          *       the status value itself must be read from the A
 717          *       channel and is only valid when read from channel A.
 718          *       Yes... broken hardware...
 719          */
 720         for (count = 16; count; count--) {
 721                 spin_lock(&scc->zlock);
 722                 zs_intreg = read_zsreg(zport_a, R3);
 723                 spin_unlock(&scc->zlock);
 724                 if (!zs_intreg)
 725                         break;
 726
 727                 /*
 728                  * We do not like losing characters, so we prioritise
 729                  * interrupt sources a little bit differently than
 730                  * the SCC would, was it allowed to.
 731                  */
 732                 if (zs_intreg & CHBRxIP)
 733                         zs_receive_chars(zport_b);
 734                 if (zs_intreg & CHARxIP)
 735                         zs_receive_chars(zport_a);
 736                 if (zs_intreg & CHBEXT)
 737                         zs_status_handle(zport_b, zport_a);
 738                 if (zs_intreg & CHAEXT)
 739                         zs_status_handle(zport_a, zport_a);
 740                 if (zs_intreg & CHBTxIP)
 741                         zs_transmit_chars(zport_b);
 742                 if (zs_intreg & CHATxIP)
 743                         zs_transmit_chars(zport_a);
 744
 745                 status = IRQ_HANDLED;
 746         }
 747
 748         return status;
 749 }
 750
 751
 752 /*
 753  * Finally, routines used to initialize the serial port.
 754  */
 755 static int zs_startup(struct uart_port *uport)
 756 {
 757         struct zs_port *zport = to_zport(uport);
 758         struct zs_scc *scc = zport->scc;
 759         unsigned long flags;
 760         int irq_guard;
 761         int ret;
 762
 763         irq_guard = atomic_add_return(1, &scc->irq_guard);
 764         if (irq_guard == 1) {
 765                 ret = request_irq(zport->port.irq, zs_interrupt,
 766                                   IRQF_SHARED, "scc", scc);
 767                 if (ret) {
 768                         atomic_add(-1, &scc->irq_guard);
 769                         printk(KERN_ERR "zs: can't get irq %d\n",
 770                                zport->port.irq);
 771                         return ret;
 772                 }
 773         }
 774
 775         spin_lock_irqsave(&scc->zlock, flags);
 776
 777         /* Clear the receive FIFO.  */
 778         zs_receive_drain(zport);
 779
 780         /* Clear the interrupt registers.  */
 781         write_zsreg(zport, R0, ERR_RES);
 782         write_zsreg(zport, R0, RES_Tx_P);
 783         /* But Ext only if not being handled already.  */
 784         if (!(zport->regs[1] & EXT_INT_ENAB))
 785                 write_zsreg(zport, R0, RES_EXT_INT);
 786
 787         /* Finally, enable sequencing and interrupts.  */
 788         zport->regs[1] &= ~RxINT_MASK;
 789         zport->regs[1] |= RxINT_ALL | TxINT_ENAB | EXT_INT_ENAB;
 790         zport->regs[3] |= RxENABLE;
 791         zport->regs[15] |= BRKIE;
 792         write_zsreg(zport, R1, zport->regs[1]);
 793         write_zsreg(zport, R3, zport->regs[3]);
 794         write_zsreg(zport, R5, zport->regs[5]);
 795         write_zsreg(zport, R15, zport->regs[15]);
 796
 797         /* Record the current state of RR0.  */
 798         zport->mctrl = zs_raw_get_mctrl(zport);
 799         zport->brk = read_zsreg(zport, R0) & BRK_ABRT;
 800
 801         zport->tx_stopped = 1;
 802
 803         spin_unlock_irqrestore(&scc->zlock, flags);
 804
 805         return 0;
 806 }
 807
 808 static void zs_shutdown(struct uart_port *uport)
 809 {
 810         struct zs_port *zport = to_zport(uport);
 811         struct zs_scc *scc = zport->scc;
 812         unsigned long flags;
 813         int irq_guard;
 814
 815         spin_lock_irqsave(&scc->zlock, flags);
 816
 817         zport->regs[3] &= ~RxENABLE;
 818         write_zsreg(zport, R5, zport->regs[5]);
 819         write_zsreg(zport, R3, zport->regs[3]);
 820
 821         spin_unlock_irqrestore(&scc->zlock, flags);
 822
 823         irq_guard = atomic_add_return(-1, &scc->irq_guard);
 824         if (!irq_guard)
 825                 free_irq(zport->port.irq, scc);
 826 }
 827
 828
 829 static void zs_reset(struct zs_port *zport)
 830 {
 831         struct zs_scc *scc = zport->scc;
 832         int irq;
 833         unsigned long flags;
 834
 835         spin_lock_irqsave(&scc->zlock, flags);
 836         irq = !irqs_disabled_flags(flags);
 837         if (!scc->initialised) {
 838                 /* Reset the pointer first, just in case...  */
 839                 read_zsreg(zport, R0);
 840                 /* And let the current transmission finish.  */
 841                 zs_line_drain(zport, irq);
 842                 write_zsreg(zport, R9, FHWRES);
 843                 udelay(10);
 844                 write_zsreg(zport, R9, 0);
 845                 scc->initialised = 1;
 846         }
 847         load_zsregs(zport, zport->regs, irq);
 848         spin_unlock_irqrestore(&scc->zlock, flags);
 849 }
 850
 851 static void zs_set_termios(struct uart_port *uport, struct ktermios *termios,
 852                            struct ktermios *old_termios)
 853 {
 854         struct zs_port *zport = to_zport(uport);
 855         struct zs_scc *scc = zport->scc;
 856         struct zs_port *zport_a = &scc->zport[ZS_CHAN_A];
 857         int irq;
 858         unsigned int baud, brg;
 859         unsigned long flags;
 860
 861         spin_lock_irqsave(&scc->zlock, flags);
 862         irq = !irqs_disabled_flags(flags);
 863
 864         /* Byte size.  */
 865         zport->regs[3] &= ~RxNBITS_MASK;
 866         zport->regs[5] &= ~TxNBITS_MASK;
 867         switch (termios->c_cflag & CSIZE) {
 868         case CS5:
 869                 zport->regs[3] |= Rx5;
 870                 zport->regs[5] |= Tx5;
 871                 break;
 872         case CS6:
 873                 zport->regs[3] |= Rx6;
 874                 zport->regs[5] |= Tx6;
 875                 break;
 876         case CS7:
 877                 zport->regs[3] |= Rx7;
 878                 zport->regs[5] |= Tx7;
 879                 break;
 880         case CS8:
 881         default:
 882                 zport->regs[3] |= Rx8;
 883                 zport->regs[5] |= Tx8;
 884                 break;
 885         }
 886
 887         /* Parity and stop bits.  */
 888         zport->regs[4] &= ~(XCLK_MASK | SB_MASK | PAR_ENA | PAR_EVEN);
 889         if (termios->c_cflag & CSTOPB)
 890                 zport->regs[4] |= SB2;
 891         else
 892                 zport->regs[4] |= SB1;
 893         if (termios->c_cflag & PARENB)
 894                 zport->regs[4] |= PAR_ENA;
 895         if (!(termios->c_cflag & PARODD))
 896                 zport->regs[4] |= PAR_EVEN;
 897         switch (zport->clk_mode) {
 898         case 64:
 899                 zport->regs[4] |= X64CLK;
 900                 break;
 901         case 32:
 902                 zport->regs[4] |= X32CLK;
 903                 break;
 904         case 16:
 905                 zport->regs[4] |= X16CLK;
 906                 break;
 907         case 1:
 908                 zport->regs[4] |= X1CLK;
 909                 break;
 910         default:
 911                 BUG();
 912         }
 913
 914         baud = uart_get_baud_rate(uport, termios, old_termios, 0,
 915                                   uport->uartclk / zport->clk_mode / 4);
 916
 917         brg = ZS_BPS_TO_BRG(baud, uport->uartclk / zport->clk_mode);
 918         zport->regs[12] = brg & 0xff;
 919         zport->regs[13] = (brg >> 8) & 0xff;
 920
 921         uart_update_timeout(uport, termios->c_cflag, baud);
 922
 923         uport->read_status_mask = Rx_OVR;
 924         if (termios->c_iflag & INPCK)
 925                 uport->read_status_mask |= FRM_ERR | PAR_ERR;
 926         if (termios->c_iflag & (IGNBRK | BRKINT | PARMRK))
 927                 uport->read_status_mask |= Rx_BRK;
 928
 929         uport->ignore_status_mask = 0;
 930         if (termios->c_iflag & IGNPAR)
 931                 uport->ignore_status_mask |= FRM_ERR | PAR_ERR;
 932         if (termios->c_iflag & IGNBRK) {
 933                 uport->ignore_status_mask |= Rx_BRK;
 934                 if (termios->c_iflag & IGNPAR)
 935                         uport->ignore_status_mask |= Rx_OVR;
 936         }
 937
 938         if (termios->c_cflag & CREAD)
 939                 zport->regs[3] |= RxENABLE;
 940         else
 941                 zport->regs[3] &= ~RxENABLE;
 942
 943         if (zport != zport_a) {
 944                 if (!(termios->c_cflag & CLOCAL)) {
 945                         zport->regs[15] |= DCDIE;
 946                 } else
 947                         zport->regs[15] &= ~DCDIE;
 948                 if (termios->c_cflag & CRTSCTS) {
 949                         zport->regs[15] |= CTSIE;
 950                 } else
 951                         zport->regs[15] &= ~CTSIE;
 952                 zs_raw_xor_mctrl(zport);
 953         }
 954
 955         /* Load up the new values.  */
 956         load_zsregs(zport, zport->regs, irq);
 957
 958         spin_unlock_irqrestore(&scc->zlock, flags);
 959 }
 960
 961 /*
 962  * Hack alert!
 963  * Required solely so that the initial PROM-based console
 964  * works undisturbed in parallel with this one.
 965  */
 966 static void zs_pm(struct uart_port *uport, unsigned int state,
 967                   unsigned int oldstate)
 968 {
 969         struct zs_port *zport = to_zport(uport);
 970
 971         if (state < 3)
 972                 zport->regs[5] |= TxENAB;
 973         else
 974                 zport->regs[5] &= ~TxENAB;
 975         write_zsreg(zport, R5, zport->regs[5]);
 976 }
 977
 978
 979 static const char *zs_type(struct uart_port *uport)
 980 {
 981         return "Z85C30 SCC";
 982 }
 983
 984 static void zs_release_port(struct uart_port *uport)
 985 {
 986         iounmap(uport->membase);
 987         uport->membase = 0;
 988         release_mem_region(uport->mapbase, ZS_CHAN_IO_SIZE);
 989 }
 990
 991 static int zs_map_port(struct uart_port *uport)
 992 {
 993         if (!uport->membase)
 994                 uport->membase = ioremap_nocache(uport->mapbase,
 995                                                  ZS_CHAN_IO_SIZE);
 996         if (!uport->membase) {
 997                 printk(KERN_ERR "zs: Cannot map MMIO\n");
 998                 return -ENOMEM;
 999         }
1000         return 0;
1001 }
1002
1003 static int zs_request_port(struct uart_port *uport)
1004 {
1005         int ret;
1006
1007         if (!request_mem_region(uport->mapbase, ZS_CHAN_IO_SIZE, "scc")) {
1008                 printk(KERN_ERR "zs: Unable to reserve MMIO resource\n");
1009                 return -EBUSY;
1010         }
1011         ret = zs_map_port(uport);
1012         if (ret) {
1013                 release_mem_region(uport->mapbase, ZS_CHAN_IO_SIZE);
1014                 return ret;
1015         }
1016         return 0;
1017 }
1018
1019 static void zs_config_port(struct uart_port *uport, int flags)
1020 {
1021         struct zs_port *zport = to_zport(uport);
1022
1023         if (flags & UART_CONFIG_TYPE) {
1024                 if (zs_request_port(uport))
1025                         return;
1026
1027                 uport->type = PORT_ZS;
1028
1029                 zs_reset(zport);
1030         }
1031 }
1032
1033 static int zs_verify_port(struct uart_port *uport, struct serial_struct *ser)
1034 {
1035         struct zs_port *zport = to_zport(uport);
1036         int ret = 0;
1037
1038         if (ser->type != PORT_UNKNOWN && ser->type != PORT_ZS)
1039                 ret = -EINVAL;
1040         if (ser->irq != uport->irq)
1041                 ret = -EINVAL;
1042         if (ser->baud_base != uport->uartclk / zport->clk_mode / 4)
1043                 ret = -EINVAL;
1044         return ret;
1045 }
1046
1047
1048 static struct uart_ops zs_ops = {
1049         .tx_empty       = zs_tx_empty,
1050         .set_mctrl      = zs_set_mctrl,
1051         .get_mctrl      = zs_get_mctrl,
1052         .stop_tx        = zs_stop_tx,
1053         .start_tx       = zs_start_tx,
1054         .stop_rx        = zs_stop_rx,
1055         .enable_ms      = zs_enable_ms,
1056         .break_ctl      = zs_break_ctl,
1057         .startup        = zs_startup,
1058         .shutdown       = zs_shutdown,
1059         .set_termios    = zs_set_termios,
1060         .pm             = zs_pm,
1061         .type           = zs_type,
1062         .release_port   = zs_release_port,
1063         .request_port   = zs_request_port,
1064         .config_port    = zs_config_port,
1065         .verify_port    = zs_verify_port,
1066 };
1067
1068 /*
1069  * Initialize Z85C30 port structures.
1070  */
1071 static int __init zs_probe_sccs(void)
1072 {
1073         static int probed;
1074         struct zs_parms zs_parms;
1075         int chip, side, irq;
1076         int n_chips = 0;
1077         int i;
1078
1079         if (probed)
1080                 return 0;
1081
1082         irq = dec_interrupt[DEC_IRQ_SCC0];
1083         if (irq >= 0) {
1084                 zs_parms.scc[n_chips] = IOASIC_SCC0;
1085                 zs_parms.irq[n_chips] = dec_interrupt[DEC_IRQ_SCC0];
1086                 n_chips++;
1087         }
1088         irq = dec_interrupt[DEC_IRQ_SCC1];
1089         if (irq >= 0) {
1090                 zs_parms.scc[n_chips] = IOASIC_SCC1;
1091                 zs_parms.irq[n_chips] = dec_interrupt[DEC_IRQ_SCC1];
1092                 n_chips++;
1093         }
1094         if (!n_chips)
1095                 return -ENXIO;
1096
1097         probed = 1;
1098
1099         for (chip = 0; chip < n_chips; chip++) {
1100                 spin_lock_init(&zs_sccs[chip].zlock);
1101                 for (side = 0; side < ZS_NUM_CHAN; side++) {
1102                         struct zs_port *zport = &zs_sccs[chip].zport[side];
1103                         struct uart_port *uport = &zport->port;
1104
1105                         zport->scc      = &zs_sccs[chip];
1106                         zport->clk_mode = 16;
1107
1108                         uport->irq      = zs_parms.irq[chip];
1109                         uport->uartclk  = ZS_CLOCK;
1110                         uport->fifosize = 1;
1111                         uport->iotype   = UPIO_MEM;
1112                         uport->flags    = UPF_BOOT_AUTOCONF;
1113                         uport->ops      = &zs_ops;
1114                         uport->line     = chip * ZS_NUM_CHAN + side;
1115                         uport->mapbase  = dec_kn_slot_base +
1116                                           zs_parms.scc[chip] +
1117                                           (side ^ ZS_CHAN_B) * ZS_CHAN_IO_SIZE;
1118
1119                         for (i = 0; i < ZS_NUM_REGS; i++)
1120                                 zport->regs[i] = zs_init_regs[i];
1121                 }
1122         }
1123
1124         return 0;
1125 }
1126
1127
1128 #ifdef CONFIG_SERIAL_ZS_CONSOLE
1129 static void zs_console_putchar(struct uart_port *uport, int ch)
1130 {
1131         struct zs_port *zport = to_zport(uport);
1132         struct zs_scc *scc = zport->scc;
1133         int irq;
1134         unsigned long flags;
1135
1136         spin_lock_irqsave(&scc->zlock, flags);
1137         irq = !irqs_disabled_flags(flags);
1138         if (zs_transmit_drain(zport, irq))
1139                 write_zsdata(zport, ch);
1140         spin_unlock_irqrestore(&scc->zlock, flags);
1141 }
1142
1143 /*
1144  * Print a string to the serial port trying not to disturb
1145  * any possible real use of the port...
1146  */
1147 static void zs_console_write(struct console *co, const char *s,
1148                              unsigned int count)
1149 {
1150         int chip = co->index / ZS_NUM_CHAN, side = co->index % ZS_NUM_CHAN;
1151         struct zs_port *zport = &zs_sccs[chip].zport[side];
1152         struct zs_scc *scc = zport->scc;
1153         unsigned long flags;
1154         u8 txint, txenb;
1155         int irq;
1156
1157         /* Disable transmit interrupts and enable the transmitter. */
1158         spin_lock_irqsave(&scc->zlock, flags);
1159         txint = zport->regs[1];
1160         txenb = zport->regs[5];
1161         if (txint & TxINT_ENAB) {
1162                 zport->regs[1] = txint & ~TxINT_ENAB;
1163                 write_zsreg(zport, R1, zport->regs[1]);
1164         }
1165         if (!(txenb & TxENAB)) {
1166                 zport->regs[5] = txenb | TxENAB;
1167                 write_zsreg(zport, R5, zport->regs[5]);
1168         }
1169         spin_unlock_irqrestore(&scc->zlock, flags);
1170
1171         uart_console_write(&zport->port, s, count, zs_console_putchar);
1172
1173         /* Restore transmit interrupts and the transmitter enable. */
1174         spin_lock_irqsave(&scc->zlock, flags);
1175         irq = !irqs_disabled_flags(flags);
1176         zs_line_drain(zport, irq);
1177         if (!(txenb & TxENAB)) {
1178                 zport->regs[5] &= ~TxENAB;
1179                 write_zsreg(zport, R5, zport->regs[5]);
1180         }
1181         if (txint & TxINT_ENAB) {
1182                 zport->regs[1] |= TxINT_ENAB;
1183                 write_zsreg(zport, R1, zport->regs[1]);
1184         }
1185         spin_unlock_irqrestore(&scc->zlock, flags);
1186 }
1187
1188 /*
1189  * Setup serial console baud/bits/parity.  We do two things here:
1190  * - construct a cflag setting for the first uart_open()
1191  * - initialise the serial port
1192  * Return non-zero if we didn't find a serial port.
1193  */
1194 static int __init zs_console_setup(struct console *co, char *options)
1195 {
1196         int chip = co->index / ZS_NUM_CHAN, side = co->index % ZS_NUM_CHAN;
1197         struct zs_port *zport = &zs_sccs[chip].zport[side];
1198         struct uart_port *uport = &zport->port;
1199         int baud = 9600;
1200         int bits = 8;
1201         int parity = 'n';
1202         int flow = 'n';
1203         int ret;
1204
1205         ret = zs_map_port(uport);
1206         if (ret)
1207                 return ret;
1208
1209         zs_reset(zport);
1210         zs_pm(uport, 0, -1);
1211
1212         if (options)
1213                 uart_parse_options(options, &baud, &parity, &bits, &flow);
1214         return uart_set_options(uport, co, baud, parity, bits, flow);
1215 }
1216
1217 static struct uart_driver zs_reg;
1218 static struct console zs_console = {
1219         .name   = "ttyS",
1220         .write  = zs_console_write,
1221         .device = uart_console_device,
1222         .setup  = zs_console_setup,
1223         .flags  = CON_PRINTBUFFER,
1224         .index  = -1,
1225         .data   = &zs_reg,
1226 };
1227
1228 /*
1229  *      Register console.
1230  */
1231 static int __init zs_serial_console_init(void)
1232 {
1233         int ret;
1234
1235         ret = zs_probe_sccs();
1236         if (ret)
1237                 return ret;
1238         register_console(&zs_console);
1239
1240         return 0;
1241 }
1242
1243 console_initcall(zs_serial_console_init);
1244
1245 #define SERIAL_ZS_CONSOLE       &zs_console
1246 #else
1247 #define SERIAL_ZS_CONSOLE       NULL
1248 #endif /* CONFIG_SERIAL_ZS_CONSOLE */
1249
1250 static struct uart_driver zs_reg = {
1251         .owner                  = THIS_MODULE,
1252         .driver_name            = "serial",
1253         .dev_name               = "ttyS",
1254         .major                  = TTY_MAJOR,
1255         .minor                  = 64,
1256         .nr                     = ZS_NUM_SCCS * ZS_NUM_CHAN,
1257         .cons                   = SERIAL_ZS_CONSOLE,
1258 };
1259
1260 /* zs_init inits the driver. */
1261 static int __init zs_init(void)
1262 {
1263         int i, ret;
1264
1265         pr_info("%s%s\n", zs_name, zs_version);
1266
1267         /* Find out how many Z85C30 SCCs we have.  */
1268         ret = zs_probe_sccs();
1269         if (ret)
1270                 return ret;
1271
1272         ret = uart_register_driver(&zs_reg);
1273         if (ret)
1274                 return ret;
1275
1276         for (i = 0; i < ZS_NUM_SCCS * ZS_NUM_CHAN; i++) {
1277                 struct zs_scc *scc = &zs_sccs[i / ZS_NUM_CHAN];
1278                 struct zs_port *zport = &scc->zport[i % ZS_NUM_CHAN];
1279                 struct uart_port *uport = &zport->port;
1280
1281                 if (zport->scc)
1282                         uart_add_one_port(&zs_reg, uport);
1283         }
1284
1285         return 0;
1286 }
1287
1288 static void __exit zs_exit(void)
1289 {
1290         int i;
1291
1292         for (i = ZS_NUM_SCCS * ZS_NUM_CHAN - 1; i >= 0; i--) {
1293                 struct zs_scc *scc = &zs_sccs[i / ZS_NUM_CHAN];
1294                 struct zs_port *zport = &scc->zport[i % ZS_NUM_CHAN];
1295                 struct uart_port *uport = &zport->port;
1296
1297                 if (zport->scc)
1298                         uart_remove_one_port(&zs_reg, uport);
1299         }
1300
1301         uart_unregister_driver(&zs_reg);
1302 }
1303
1304 module_init(zs_init);
1305 module_exit(zs_exit);