These changes are the raw update to linux-4.4.6-rt14. Kernel sources
[kvmfornfv.git] / kernel / drivers / scsi / pm8001 / pm8001_hwi.c
1 /*
2  * PMC-Sierra SPC 8001 SAS/SATA based host adapters driver
3  *
4  * Copyright (c) 2008-2009 USI Co., Ltd.
5  * All rights reserved.
6  *
7  * Redistribution and use in source and binary forms, with or without
8  * modification, are permitted provided that the following conditions
9  * are met:
10  * 1. Redistributions of source code must retain the above copyright
11  *    notice, this list of conditions, and the following disclaimer,
12  *    without modification.
13  * 2. Redistributions in binary form must reproduce at minimum a disclaimer
14  *    substantially similar to the "NO WARRANTY" disclaimer below
15  *    ("Disclaimer") and any redistribution must be conditioned upon
16  *    including a substantially similar Disclaimer requirement for further
17  *    binary redistribution.
18  * 3. Neither the names of the above-listed copyright holders nor the names
19  *    of any contributors may be used to endorse or promote products derived
20  *    from this software without specific prior written permission.
21  *
22  * Alternatively, this software may be distributed under the terms of the
23  * GNU General Public License ("GPL") version 2 as published by the Free
24  * Software Foundation.
25  *
26  * NO WARRANTY
27  * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
28  * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
29  * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTIBILITY AND FITNESS FOR
30  * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
31  * HOLDERS OR CONTRIBUTORS BE LIABLE FOR SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
32  * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
33  * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
34  * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
35  * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING
36  * IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
37  * POSSIBILITY OF SUCH DAMAGES.
38  *
39  */
40  #include <linux/slab.h>
41  #include "pm8001_sas.h"
42  #include "pm8001_hwi.h"
43  #include "pm8001_chips.h"
44  #include "pm8001_ctl.h"
45
46 /**
47  * read_main_config_table - read the configure table and save it.
48  * @pm8001_ha: our hba card information
49  */
50 static void read_main_config_table(struct pm8001_hba_info *pm8001_ha)
51 {
52         void __iomem *address = pm8001_ha->main_cfg_tbl_addr;
53         pm8001_ha->main_cfg_tbl.pm8001_tbl.signature    =
54                                 pm8001_mr32(address, 0x00);
55         pm8001_ha->main_cfg_tbl.pm8001_tbl.interface_rev =
56                                 pm8001_mr32(address, 0x04);
57         pm8001_ha->main_cfg_tbl.pm8001_tbl.firmware_rev =
58                                 pm8001_mr32(address, 0x08);
59         pm8001_ha->main_cfg_tbl.pm8001_tbl.max_out_io   =
60                                 pm8001_mr32(address, 0x0C);
61         pm8001_ha->main_cfg_tbl.pm8001_tbl.max_sgl      =
62                                 pm8001_mr32(address, 0x10);
63         pm8001_ha->main_cfg_tbl.pm8001_tbl.ctrl_cap_flag =
64                                 pm8001_mr32(address, 0x14);
65         pm8001_ha->main_cfg_tbl.pm8001_tbl.gst_offset   =
66                                 pm8001_mr32(address, 0x18);
67         pm8001_ha->main_cfg_tbl.pm8001_tbl.inbound_queue_offset =
68                 pm8001_mr32(address, MAIN_IBQ_OFFSET);
69         pm8001_ha->main_cfg_tbl.pm8001_tbl.outbound_queue_offset =
70                 pm8001_mr32(address, MAIN_OBQ_OFFSET);
71         pm8001_ha->main_cfg_tbl.pm8001_tbl.hda_mode_flag        =
72                 pm8001_mr32(address, MAIN_HDA_FLAGS_OFFSET);
73
74         /* read analog Setting offset from the configuration table */
75         pm8001_ha->main_cfg_tbl.pm8001_tbl.anolog_setup_table_offset =
76                 pm8001_mr32(address, MAIN_ANALOG_SETUP_OFFSET);
77
78         /* read Error Dump Offset and Length */
79         pm8001_ha->main_cfg_tbl.pm8001_tbl.fatal_err_dump_offset0 =
80                 pm8001_mr32(address, MAIN_FATAL_ERROR_RDUMP0_OFFSET);
81         pm8001_ha->main_cfg_tbl.pm8001_tbl.fatal_err_dump_length0 =
82                 pm8001_mr32(address, MAIN_FATAL_ERROR_RDUMP0_LENGTH);
83         pm8001_ha->main_cfg_tbl.pm8001_tbl.fatal_err_dump_offset1 =
84                 pm8001_mr32(address, MAIN_FATAL_ERROR_RDUMP1_OFFSET);
85         pm8001_ha->main_cfg_tbl.pm8001_tbl.fatal_err_dump_length1 =
86                 pm8001_mr32(address, MAIN_FATAL_ERROR_RDUMP1_LENGTH);
87 }
88
89 /**
90  * read_general_status_table - read the general status table and save it.
91  * @pm8001_ha: our hba card information
92  */
93 static void read_general_status_table(struct pm8001_hba_info *pm8001_ha)
94 {
95         void __iomem *address = pm8001_ha->general_stat_tbl_addr;
96         pm8001_ha->gs_tbl.pm8001_tbl.gst_len_mpistate   =
97                                 pm8001_mr32(address, 0x00);
98         pm8001_ha->gs_tbl.pm8001_tbl.iq_freeze_state0   =
99                                 pm8001_mr32(address, 0x04);
100         pm8001_ha->gs_tbl.pm8001_tbl.iq_freeze_state1   =
101                                 pm8001_mr32(address, 0x08);
102         pm8001_ha->gs_tbl.pm8001_tbl.msgu_tcnt          =
103                                 pm8001_mr32(address, 0x0C);
104         pm8001_ha->gs_tbl.pm8001_tbl.iop_tcnt           =
105                                 pm8001_mr32(address, 0x10);
106         pm8001_ha->gs_tbl.pm8001_tbl.rsvd               =
107                                 pm8001_mr32(address, 0x14);
108         pm8001_ha->gs_tbl.pm8001_tbl.phy_state[0]       =
109                                 pm8001_mr32(address, 0x18);
110         pm8001_ha->gs_tbl.pm8001_tbl.phy_state[1]       =
111                                 pm8001_mr32(address, 0x1C);
112         pm8001_ha->gs_tbl.pm8001_tbl.phy_state[2]       =
113                                 pm8001_mr32(address, 0x20);
114         pm8001_ha->gs_tbl.pm8001_tbl.phy_state[3]       =
115                                 pm8001_mr32(address, 0x24);
116         pm8001_ha->gs_tbl.pm8001_tbl.phy_state[4]       =
117                                 pm8001_mr32(address, 0x28);
118         pm8001_ha->gs_tbl.pm8001_tbl.phy_state[5]       =
119                                 pm8001_mr32(address, 0x2C);
120         pm8001_ha->gs_tbl.pm8001_tbl.phy_state[6]       =
121                                 pm8001_mr32(address, 0x30);
122         pm8001_ha->gs_tbl.pm8001_tbl.phy_state[7]       =
123                                 pm8001_mr32(address, 0x34);
124         pm8001_ha->gs_tbl.pm8001_tbl.gpio_input_val     =
125                                 pm8001_mr32(address, 0x38);
126         pm8001_ha->gs_tbl.pm8001_tbl.rsvd1[0]           =
127                                 pm8001_mr32(address, 0x3C);
128         pm8001_ha->gs_tbl.pm8001_tbl.rsvd1[1]           =
129                                 pm8001_mr32(address, 0x40);
130         pm8001_ha->gs_tbl.pm8001_tbl.recover_err_info[0]        =
131                                 pm8001_mr32(address, 0x44);
132         pm8001_ha->gs_tbl.pm8001_tbl.recover_err_info[1]        =
133                                 pm8001_mr32(address, 0x48);
134         pm8001_ha->gs_tbl.pm8001_tbl.recover_err_info[2]        =
135                                 pm8001_mr32(address, 0x4C);
136         pm8001_ha->gs_tbl.pm8001_tbl.recover_err_info[3]        =
137                                 pm8001_mr32(address, 0x50);
138         pm8001_ha->gs_tbl.pm8001_tbl.recover_err_info[4]        =
139                                 pm8001_mr32(address, 0x54);
140         pm8001_ha->gs_tbl.pm8001_tbl.recover_err_info[5]        =
141                                 pm8001_mr32(address, 0x58);
142         pm8001_ha->gs_tbl.pm8001_tbl.recover_err_info[6]        =
143                                 pm8001_mr32(address, 0x5C);
144         pm8001_ha->gs_tbl.pm8001_tbl.recover_err_info[7]        =
145                                 pm8001_mr32(address, 0x60);
146 }
147
148 /**
149  * read_inbnd_queue_table - read the inbound queue table and save it.
150  * @pm8001_ha: our hba card information
151  */
152 static void read_inbnd_queue_table(struct pm8001_hba_info *pm8001_ha)
153 {
154         int i;
155         void __iomem *address = pm8001_ha->inbnd_q_tbl_addr;
156         for (i = 0; i < PM8001_MAX_INB_NUM; i++) {
157                 u32 offset = i * 0x20;
158                 pm8001_ha->inbnd_q_tbl[i].pi_pci_bar =
159                       get_pci_bar_index(pm8001_mr32(address, (offset + 0x14)));
160                 pm8001_ha->inbnd_q_tbl[i].pi_offset =
161                         pm8001_mr32(address, (offset + 0x18));
162         }
163 }
164
165 /**
166  * read_outbnd_queue_table - read the outbound queue table and save it.
167  * @pm8001_ha: our hba card information
168  */
169 static void read_outbnd_queue_table(struct pm8001_hba_info *pm8001_ha)
170 {
171         int i;
172         void __iomem *address = pm8001_ha->outbnd_q_tbl_addr;
173         for (i = 0; i < PM8001_MAX_OUTB_NUM; i++) {
174                 u32 offset = i * 0x24;
175                 pm8001_ha->outbnd_q_tbl[i].ci_pci_bar =
176                       get_pci_bar_index(pm8001_mr32(address, (offset + 0x14)));
177                 pm8001_ha->outbnd_q_tbl[i].ci_offset =
178                         pm8001_mr32(address, (offset + 0x18));
179         }
180 }
181
182 /**
183  * init_default_table_values - init the default table.
184  * @pm8001_ha: our hba card information
185  */
186 static void init_default_table_values(struct pm8001_hba_info *pm8001_ha)
187 {
188         int i;
189         u32 offsetib, offsetob;
190         void __iomem *addressib = pm8001_ha->inbnd_q_tbl_addr;
191         void __iomem *addressob = pm8001_ha->outbnd_q_tbl_addr;
192
193         pm8001_ha->main_cfg_tbl.pm8001_tbl.inbound_q_nppd_hppd          = 0;
194         pm8001_ha->main_cfg_tbl.pm8001_tbl.outbound_hw_event_pid0_3     = 0;
195         pm8001_ha->main_cfg_tbl.pm8001_tbl.outbound_hw_event_pid4_7     = 0;
196         pm8001_ha->main_cfg_tbl.pm8001_tbl.outbound_ncq_event_pid0_3    = 0;
197         pm8001_ha->main_cfg_tbl.pm8001_tbl.outbound_ncq_event_pid4_7    = 0;
198         pm8001_ha->main_cfg_tbl.pm8001_tbl.outbound_tgt_ITNexus_event_pid0_3 =
199                                                                          0;
200         pm8001_ha->main_cfg_tbl.pm8001_tbl.outbound_tgt_ITNexus_event_pid4_7 =
201                                                                          0;
202         pm8001_ha->main_cfg_tbl.pm8001_tbl.outbound_tgt_ssp_event_pid0_3 = 0;
203         pm8001_ha->main_cfg_tbl.pm8001_tbl.outbound_tgt_ssp_event_pid4_7 = 0;
204         pm8001_ha->main_cfg_tbl.pm8001_tbl.outbound_tgt_smp_event_pid0_3 = 0;
205         pm8001_ha->main_cfg_tbl.pm8001_tbl.outbound_tgt_smp_event_pid4_7 = 0;
206
207         pm8001_ha->main_cfg_tbl.pm8001_tbl.upper_event_log_addr         =
208                 pm8001_ha->memoryMap.region[AAP1].phys_addr_hi;
209         pm8001_ha->main_cfg_tbl.pm8001_tbl.lower_event_log_addr         =
210                 pm8001_ha->memoryMap.region[AAP1].phys_addr_lo;
211         pm8001_ha->main_cfg_tbl.pm8001_tbl.event_log_size               =
212                 PM8001_EVENT_LOG_SIZE;
213         pm8001_ha->main_cfg_tbl.pm8001_tbl.event_log_option             = 0x01;
214         pm8001_ha->main_cfg_tbl.pm8001_tbl.upper_iop_event_log_addr     =
215                 pm8001_ha->memoryMap.region[IOP].phys_addr_hi;
216         pm8001_ha->main_cfg_tbl.pm8001_tbl.lower_iop_event_log_addr     =
217                 pm8001_ha->memoryMap.region[IOP].phys_addr_lo;
218         pm8001_ha->main_cfg_tbl.pm8001_tbl.iop_event_log_size           =
219                 PM8001_EVENT_LOG_SIZE;
220         pm8001_ha->main_cfg_tbl.pm8001_tbl.iop_event_log_option         = 0x01;
221         pm8001_ha->main_cfg_tbl.pm8001_tbl.fatal_err_interrupt          = 0x01;
222         for (i = 0; i < PM8001_MAX_INB_NUM; i++) {
223                 pm8001_ha->inbnd_q_tbl[i].element_pri_size_cnt  =
224                         PM8001_MPI_QUEUE | (pm8001_ha->iomb_size << 16) | (0x00<<30);
225                 pm8001_ha->inbnd_q_tbl[i].upper_base_addr       =
226                         pm8001_ha->memoryMap.region[IB + i].phys_addr_hi;
227                 pm8001_ha->inbnd_q_tbl[i].lower_base_addr       =
228                 pm8001_ha->memoryMap.region[IB + i].phys_addr_lo;
229                 pm8001_ha->inbnd_q_tbl[i].base_virt             =
230                         (u8 *)pm8001_ha->memoryMap.region[IB + i].virt_ptr;
231                 pm8001_ha->inbnd_q_tbl[i].total_length          =
232                         pm8001_ha->memoryMap.region[IB + i].total_len;
233                 pm8001_ha->inbnd_q_tbl[i].ci_upper_base_addr    =
234                         pm8001_ha->memoryMap.region[CI + i].phys_addr_hi;
235                 pm8001_ha->inbnd_q_tbl[i].ci_lower_base_addr    =
236                         pm8001_ha->memoryMap.region[CI + i].phys_addr_lo;
237                 pm8001_ha->inbnd_q_tbl[i].ci_virt               =
238                         pm8001_ha->memoryMap.region[CI + i].virt_ptr;
239                 offsetib = i * 0x20;
240                 pm8001_ha->inbnd_q_tbl[i].pi_pci_bar            =
241                         get_pci_bar_index(pm8001_mr32(addressib,
242                                 (offsetib + 0x14)));
243                 pm8001_ha->inbnd_q_tbl[i].pi_offset             =
244                         pm8001_mr32(addressib, (offsetib + 0x18));
245                 pm8001_ha->inbnd_q_tbl[i].producer_idx          = 0;
246                 pm8001_ha->inbnd_q_tbl[i].consumer_index        = 0;
247         }
248         for (i = 0; i < PM8001_MAX_OUTB_NUM; i++) {
249                 pm8001_ha->outbnd_q_tbl[i].element_size_cnt     =
250                         PM8001_MPI_QUEUE | (pm8001_ha->iomb_size << 16) | (0x01<<30);
251                 pm8001_ha->outbnd_q_tbl[i].upper_base_addr      =
252                         pm8001_ha->memoryMap.region[OB + i].phys_addr_hi;
253                 pm8001_ha->outbnd_q_tbl[i].lower_base_addr      =
254                         pm8001_ha->memoryMap.region[OB + i].phys_addr_lo;
255                 pm8001_ha->outbnd_q_tbl[i].base_virt            =
256                         (u8 *)pm8001_ha->memoryMap.region[OB + i].virt_ptr;
257                 pm8001_ha->outbnd_q_tbl[i].total_length         =
258                         pm8001_ha->memoryMap.region[OB + i].total_len;
259                 pm8001_ha->outbnd_q_tbl[i].pi_upper_base_addr   =
260                         pm8001_ha->memoryMap.region[PI + i].phys_addr_hi;
261                 pm8001_ha->outbnd_q_tbl[i].pi_lower_base_addr   =
262                         pm8001_ha->memoryMap.region[PI + i].phys_addr_lo;
263                 pm8001_ha->outbnd_q_tbl[i].interrup_vec_cnt_delay       =
264                         0 | (10 << 16) | (i << 24);
265                 pm8001_ha->outbnd_q_tbl[i].pi_virt              =
266                         pm8001_ha->memoryMap.region[PI + i].virt_ptr;
267                 offsetob = i * 0x24;
268                 pm8001_ha->outbnd_q_tbl[i].ci_pci_bar           =
269                         get_pci_bar_index(pm8001_mr32(addressob,
270                         offsetob + 0x14));
271                 pm8001_ha->outbnd_q_tbl[i].ci_offset            =
272                         pm8001_mr32(addressob, (offsetob + 0x18));
273                 pm8001_ha->outbnd_q_tbl[i].consumer_idx         = 0;
274                 pm8001_ha->outbnd_q_tbl[i].producer_index       = 0;
275         }
276 }
277
278 /**
279  * update_main_config_table - update the main default table to the HBA.
280  * @pm8001_ha: our hba card information
281  */
282 static void update_main_config_table(struct pm8001_hba_info *pm8001_ha)
283 {
284         void __iomem *address = pm8001_ha->main_cfg_tbl_addr;
285         pm8001_mw32(address, 0x24,
286                 pm8001_ha->main_cfg_tbl.pm8001_tbl.inbound_q_nppd_hppd);
287         pm8001_mw32(address, 0x28,
288                 pm8001_ha->main_cfg_tbl.pm8001_tbl.outbound_hw_event_pid0_3);
289         pm8001_mw32(address, 0x2C,
290                 pm8001_ha->main_cfg_tbl.pm8001_tbl.outbound_hw_event_pid4_7);
291         pm8001_mw32(address, 0x30,
292                 pm8001_ha->main_cfg_tbl.pm8001_tbl.outbound_ncq_event_pid0_3);
293         pm8001_mw32(address, 0x34,
294                 pm8001_ha->main_cfg_tbl.pm8001_tbl.outbound_ncq_event_pid4_7);
295         pm8001_mw32(address, 0x38,
296                 pm8001_ha->main_cfg_tbl.pm8001_tbl.
297                                         outbound_tgt_ITNexus_event_pid0_3);
298         pm8001_mw32(address, 0x3C,
299                 pm8001_ha->main_cfg_tbl.pm8001_tbl.
300                                         outbound_tgt_ITNexus_event_pid4_7);
301         pm8001_mw32(address, 0x40,
302                 pm8001_ha->main_cfg_tbl.pm8001_tbl.
303                                         outbound_tgt_ssp_event_pid0_3);
304         pm8001_mw32(address, 0x44,
305                 pm8001_ha->main_cfg_tbl.pm8001_tbl.
306                                         outbound_tgt_ssp_event_pid4_7);
307         pm8001_mw32(address, 0x48,
308                 pm8001_ha->main_cfg_tbl.pm8001_tbl.
309                                         outbound_tgt_smp_event_pid0_3);
310         pm8001_mw32(address, 0x4C,
311                 pm8001_ha->main_cfg_tbl.pm8001_tbl.
312                                         outbound_tgt_smp_event_pid4_7);
313         pm8001_mw32(address, 0x50,
314                 pm8001_ha->main_cfg_tbl.pm8001_tbl.upper_event_log_addr);
315         pm8001_mw32(address, 0x54,
316                 pm8001_ha->main_cfg_tbl.pm8001_tbl.lower_event_log_addr);
317         pm8001_mw32(address, 0x58,
318                 pm8001_ha->main_cfg_tbl.pm8001_tbl.event_log_size);
319         pm8001_mw32(address, 0x5C,
320                 pm8001_ha->main_cfg_tbl.pm8001_tbl.event_log_option);
321         pm8001_mw32(address, 0x60,
322                 pm8001_ha->main_cfg_tbl.pm8001_tbl.upper_iop_event_log_addr);
323         pm8001_mw32(address, 0x64,
324                 pm8001_ha->main_cfg_tbl.pm8001_tbl.lower_iop_event_log_addr);
325         pm8001_mw32(address, 0x68,
326                 pm8001_ha->main_cfg_tbl.pm8001_tbl.iop_event_log_size);
327         pm8001_mw32(address, 0x6C,
328                 pm8001_ha->main_cfg_tbl.pm8001_tbl.iop_event_log_option);
329         pm8001_mw32(address, 0x70,
330                 pm8001_ha->main_cfg_tbl.pm8001_tbl.fatal_err_interrupt);
331 }
332
333 /**
334  * update_inbnd_queue_table - update the inbound queue table to the HBA.
335  * @pm8001_ha: our hba card information
336  */
337 static void update_inbnd_queue_table(struct pm8001_hba_info *pm8001_ha,
338                                      int number)
339 {
340         void __iomem *address = pm8001_ha->inbnd_q_tbl_addr;
341         u16 offset = number * 0x20;
342         pm8001_mw32(address, offset + 0x00,
343                 pm8001_ha->inbnd_q_tbl[number].element_pri_size_cnt);
344         pm8001_mw32(address, offset + 0x04,
345                 pm8001_ha->inbnd_q_tbl[number].upper_base_addr);
346         pm8001_mw32(address, offset + 0x08,
347                 pm8001_ha->inbnd_q_tbl[number].lower_base_addr);
348         pm8001_mw32(address, offset + 0x0C,
349                 pm8001_ha->inbnd_q_tbl[number].ci_upper_base_addr);
350         pm8001_mw32(address, offset + 0x10,
351                 pm8001_ha->inbnd_q_tbl[number].ci_lower_base_addr);
352 }
353
354 /**
355  * update_outbnd_queue_table - update the outbound queue table to the HBA.
356  * @pm8001_ha: our hba card information
357  */
358 static void update_outbnd_queue_table(struct pm8001_hba_info *pm8001_ha,
359                                       int number)
360 {
361         void __iomem *address = pm8001_ha->outbnd_q_tbl_addr;
362         u16 offset = number * 0x24;
363         pm8001_mw32(address, offset + 0x00,
364                 pm8001_ha->outbnd_q_tbl[number].element_size_cnt);
365         pm8001_mw32(address, offset + 0x04,
366                 pm8001_ha->outbnd_q_tbl[number].upper_base_addr);
367         pm8001_mw32(address, offset + 0x08,
368                 pm8001_ha->outbnd_q_tbl[number].lower_base_addr);
369         pm8001_mw32(address, offset + 0x0C,
370                 pm8001_ha->outbnd_q_tbl[number].pi_upper_base_addr);
371         pm8001_mw32(address, offset + 0x10,
372                 pm8001_ha->outbnd_q_tbl[number].pi_lower_base_addr);
373         pm8001_mw32(address, offset + 0x1C,
374                 pm8001_ha->outbnd_q_tbl[number].interrup_vec_cnt_delay);
375 }
376
377 /**
378  * pm8001_bar4_shift - function is called to shift BAR base address
379  * @pm8001_ha : our hba card infomation
380  * @shiftValue : shifting value in memory bar.
381  */
382 int pm8001_bar4_shift(struct pm8001_hba_info *pm8001_ha, u32 shiftValue)
383 {
384         u32 regVal;
385         unsigned long start;
386
387         /* program the inbound AXI translation Lower Address */
388         pm8001_cw32(pm8001_ha, 1, SPC_IBW_AXI_TRANSLATION_LOW, shiftValue);
389
390         /* confirm the setting is written */
391         start = jiffies + HZ; /* 1 sec */
392         do {
393                 regVal = pm8001_cr32(pm8001_ha, 1, SPC_IBW_AXI_TRANSLATION_LOW);
394         } while ((regVal != shiftValue) && time_before(jiffies, start));
395
396         if (regVal != shiftValue) {
397                 PM8001_INIT_DBG(pm8001_ha,
398                         pm8001_printk("TIMEOUT:SPC_IBW_AXI_TRANSLATION_LOW"
399                         " = 0x%x\n", regVal));
400                 return -1;
401         }
402         return 0;
403 }
404
405 /**
406  * mpi_set_phys_g3_with_ssc
407  * @pm8001_ha: our hba card information
408  * @SSCbit: set SSCbit to 0 to disable all phys ssc; 1 to enable all phys ssc.
409  */
410 static void mpi_set_phys_g3_with_ssc(struct pm8001_hba_info *pm8001_ha,
411                                      u32 SSCbit)
412 {
413         u32 value, offset, i;
414         unsigned long flags;
415
416 #define SAS2_SETTINGS_LOCAL_PHY_0_3_SHIFT_ADDR 0x00030000
417 #define SAS2_SETTINGS_LOCAL_PHY_4_7_SHIFT_ADDR 0x00040000
418 #define SAS2_SETTINGS_LOCAL_PHY_0_3_OFFSET 0x1074
419 #define SAS2_SETTINGS_LOCAL_PHY_4_7_OFFSET 0x1074
420 #define PHY_G3_WITHOUT_SSC_BIT_SHIFT 12
421 #define PHY_G3_WITH_SSC_BIT_SHIFT 13
422 #define SNW3_PHY_CAPABILITIES_PARITY 31
423
424    /*
425     * Using shifted destination address 0x3_0000:0x1074 + 0x4000*N (N=0:3)
426     * Using shifted destination address 0x4_0000:0x1074 + 0x4000*(N-4) (N=4:7)
427     */
428         spin_lock_irqsave(&pm8001_ha->lock, flags);
429         if (-1 == pm8001_bar4_shift(pm8001_ha,
430                                 SAS2_SETTINGS_LOCAL_PHY_0_3_SHIFT_ADDR)) {
431                 spin_unlock_irqrestore(&pm8001_ha->lock, flags);
432                 return;
433         }
434
435         for (i = 0; i < 4; i++) {
436                 offset = SAS2_SETTINGS_LOCAL_PHY_0_3_OFFSET + 0x4000 * i;
437                 pm8001_cw32(pm8001_ha, 2, offset, 0x80001501);
438         }
439         /* shift membase 3 for SAS2_SETTINGS_LOCAL_PHY 4 - 7 */
440         if (-1 == pm8001_bar4_shift(pm8001_ha,
441                                 SAS2_SETTINGS_LOCAL_PHY_4_7_SHIFT_ADDR)) {
442                 spin_unlock_irqrestore(&pm8001_ha->lock, flags);
443                 return;
444         }
445         for (i = 4; i < 8; i++) {
446                 offset = SAS2_SETTINGS_LOCAL_PHY_4_7_OFFSET + 0x4000 * (i-4);
447                 pm8001_cw32(pm8001_ha, 2, offset, 0x80001501);
448         }
449         /*************************************************************
450         Change the SSC upspreading value to 0x0 so that upspreading is disabled.
451         Device MABC SMOD0 Controls
452         Address: (via MEMBASE-III):
453         Using shifted destination address 0x0_0000: with Offset 0xD8
454
455         31:28 R/W Reserved Do not change
456         27:24 R/W SAS_SMOD_SPRDUP 0000
457         23:20 R/W SAS_SMOD_SPRDDN 0000
458         19:0  R/W  Reserved Do not change
459         Upon power-up this register will read as 0x8990c016,
460         and I would like you to change the SAS_SMOD_SPRDUP bits to 0b0000
461         so that the written value will be 0x8090c016.
462         This will ensure only down-spreading SSC is enabled on the SPC.
463         *************************************************************/
464         value = pm8001_cr32(pm8001_ha, 2, 0xd8);
465         pm8001_cw32(pm8001_ha, 2, 0xd8, 0x8000C016);
466
467         /*set the shifted destination address to 0x0 to avoid error operation */
468         pm8001_bar4_shift(pm8001_ha, 0x0);
469         spin_unlock_irqrestore(&pm8001_ha->lock, flags);
470         return;
471 }
472
473 /**
474  * mpi_set_open_retry_interval_reg
475  * @pm8001_ha: our hba card information
476  * @interval - interval time for each OPEN_REJECT (RETRY). The units are in 1us.
477  */
478 static void mpi_set_open_retry_interval_reg(struct pm8001_hba_info *pm8001_ha,
479                                             u32 interval)
480 {
481         u32 offset;
482         u32 value;
483         u32 i;
484         unsigned long flags;
485
486 #define OPEN_RETRY_INTERVAL_PHY_0_3_SHIFT_ADDR 0x00030000
487 #define OPEN_RETRY_INTERVAL_PHY_4_7_SHIFT_ADDR 0x00040000
488 #define OPEN_RETRY_INTERVAL_PHY_0_3_OFFSET 0x30B4
489 #define OPEN_RETRY_INTERVAL_PHY_4_7_OFFSET 0x30B4
490 #define OPEN_RETRY_INTERVAL_REG_MASK 0x0000FFFF
491
492         value = interval & OPEN_RETRY_INTERVAL_REG_MASK;
493         spin_lock_irqsave(&pm8001_ha->lock, flags);
494         /* shift bar and set the OPEN_REJECT(RETRY) interval time of PHY 0 -3.*/
495         if (-1 == pm8001_bar4_shift(pm8001_ha,
496                              OPEN_RETRY_INTERVAL_PHY_0_3_SHIFT_ADDR)) {
497                 spin_unlock_irqrestore(&pm8001_ha->lock, flags);
498                 return;
499         }
500         for (i = 0; i < 4; i++) {
501                 offset = OPEN_RETRY_INTERVAL_PHY_0_3_OFFSET + 0x4000 * i;
502                 pm8001_cw32(pm8001_ha, 2, offset, value);
503         }
504
505         if (-1 == pm8001_bar4_shift(pm8001_ha,
506                              OPEN_RETRY_INTERVAL_PHY_4_7_SHIFT_ADDR)) {
507                 spin_unlock_irqrestore(&pm8001_ha->lock, flags);
508                 return;
509         }
510         for (i = 4; i < 8; i++) {
511                 offset = OPEN_RETRY_INTERVAL_PHY_4_7_OFFSET + 0x4000 * (i-4);
512                 pm8001_cw32(pm8001_ha, 2, offset, value);
513         }
514         /*set the shifted destination address to 0x0 to avoid error operation */
515         pm8001_bar4_shift(pm8001_ha, 0x0);
516         spin_unlock_irqrestore(&pm8001_ha->lock, flags);
517         return;
518 }
519
520 /**
521  * mpi_init_check - check firmware initialization status.
522  * @pm8001_ha: our hba card information
523  */
524 static int mpi_init_check(struct pm8001_hba_info *pm8001_ha)
525 {
526         u32 max_wait_count;
527         u32 value;
528         u32 gst_len_mpistate;
529         /* Write bit0=1 to Inbound DoorBell Register to tell the SPC FW the
530         table is updated */
531         pm8001_cw32(pm8001_ha, 0, MSGU_IBDB_SET, SPC_MSGU_CFG_TABLE_UPDATE);
532         /* wait until Inbound DoorBell Clear Register toggled */
533         max_wait_count = 1 * 1000 * 1000;/* 1 sec */
534         do {
535                 udelay(1);
536                 value = pm8001_cr32(pm8001_ha, 0, MSGU_IBDB_SET);
537                 value &= SPC_MSGU_CFG_TABLE_UPDATE;
538         } while ((value != 0) && (--max_wait_count));
539
540         if (!max_wait_count)
541                 return -1;
542         /* check the MPI-State for initialization */
543         gst_len_mpistate =
544                 pm8001_mr32(pm8001_ha->general_stat_tbl_addr,
545                 GST_GSTLEN_MPIS_OFFSET);
546         if (GST_MPI_STATE_INIT != (gst_len_mpistate & GST_MPI_STATE_MASK))
547                 return -1;
548         /* check MPI Initialization error */
549         gst_len_mpistate = gst_len_mpistate >> 16;
550         if (0x0000 != gst_len_mpistate)
551                 return -1;
552         return 0;
553 }
554
555 /**
556  * check_fw_ready - The LLDD check if the FW is ready, if not, return error.
557  * @pm8001_ha: our hba card information
558  */
559 static int check_fw_ready(struct pm8001_hba_info *pm8001_ha)
560 {
561         u32 value, value1;
562         u32 max_wait_count;
563         /* check error state */
564         value = pm8001_cr32(pm8001_ha, 0, MSGU_SCRATCH_PAD_1);
565         value1 = pm8001_cr32(pm8001_ha, 0, MSGU_SCRATCH_PAD_2);
566         /* check AAP error */
567         if (SCRATCH_PAD1_ERR == (value & SCRATCH_PAD_STATE_MASK)) {
568                 /* error state */
569                 value = pm8001_cr32(pm8001_ha, 0, MSGU_SCRATCH_PAD_0);
570                 return -1;
571         }
572
573         /* check IOP error */
574         if (SCRATCH_PAD2_ERR == (value1 & SCRATCH_PAD_STATE_MASK)) {
575                 /* error state */
576                 value1 = pm8001_cr32(pm8001_ha, 0, MSGU_SCRATCH_PAD_3);
577                 return -1;
578         }
579
580         /* bit 4-31 of scratch pad1 should be zeros if it is not
581         in error state*/
582         if (value & SCRATCH_PAD1_STATE_MASK) {
583                 /* error case */
584                 pm8001_cr32(pm8001_ha, 0, MSGU_SCRATCH_PAD_0);
585                 return -1;
586         }
587
588         /* bit 2, 4-31 of scratch pad2 should be zeros if it is not
589         in error state */
590         if (value1 & SCRATCH_PAD2_STATE_MASK) {
591                 /* error case */
592                 return -1;
593         }
594
595         max_wait_count = 1 * 1000 * 1000;/* 1 sec timeout */
596
597         /* wait until scratch pad 1 and 2 registers in ready state  */
598         do {
599                 udelay(1);
600                 value = pm8001_cr32(pm8001_ha, 0, MSGU_SCRATCH_PAD_1)
601                         & SCRATCH_PAD1_RDY;
602                 value1 = pm8001_cr32(pm8001_ha, 0, MSGU_SCRATCH_PAD_2)
603                         & SCRATCH_PAD2_RDY;
604                 if ((--max_wait_count) == 0)
605                         return -1;
606         } while ((value != SCRATCH_PAD1_RDY) || (value1 != SCRATCH_PAD2_RDY));
607         return 0;
608 }
609
610 static void init_pci_device_addresses(struct pm8001_hba_info *pm8001_ha)
611 {
612         void __iomem *base_addr;
613         u32     value;
614         u32     offset;
615         u32     pcibar;
616         u32     pcilogic;
617
618         value = pm8001_cr32(pm8001_ha, 0, 0x44);
619         offset = value & 0x03FFFFFF;
620         PM8001_INIT_DBG(pm8001_ha,
621                 pm8001_printk("Scratchpad 0 Offset: %x\n", offset));
622         pcilogic = (value & 0xFC000000) >> 26;
623         pcibar = get_pci_bar_index(pcilogic);
624         PM8001_INIT_DBG(pm8001_ha,
625                 pm8001_printk("Scratchpad 0 PCI BAR: %d\n", pcibar));
626         pm8001_ha->main_cfg_tbl_addr = base_addr =
627                 pm8001_ha->io_mem[pcibar].memvirtaddr + offset;
628         pm8001_ha->general_stat_tbl_addr =
629                 base_addr + pm8001_cr32(pm8001_ha, pcibar, offset + 0x18);
630         pm8001_ha->inbnd_q_tbl_addr =
631                 base_addr + pm8001_cr32(pm8001_ha, pcibar, offset + 0x1C);
632         pm8001_ha->outbnd_q_tbl_addr =
633                 base_addr + pm8001_cr32(pm8001_ha, pcibar, offset + 0x20);
634 }
635
636 /**
637  * pm8001_chip_init - the main init function that initialize whole PM8001 chip.
638  * @pm8001_ha: our hba card information
639  */
640 static int pm8001_chip_init(struct pm8001_hba_info *pm8001_ha)
641 {
642         u8 i = 0;
643         u16 deviceid;
644         pci_read_config_word(pm8001_ha->pdev, PCI_DEVICE_ID, &deviceid);
645         /* 8081 controllers need BAR shift to access MPI space
646         * as this is shared with BIOS data */
647         if (deviceid == 0x8081 || deviceid == 0x0042) {
648                 if (-1 == pm8001_bar4_shift(pm8001_ha, GSM_SM_BASE)) {
649                         PM8001_FAIL_DBG(pm8001_ha,
650                                 pm8001_printk("Shift Bar4 to 0x%x failed\n",
651                                         GSM_SM_BASE));
652                         return -1;
653                 }
654         }
655         /* check the firmware status */
656         if (-1 == check_fw_ready(pm8001_ha)) {
657                 PM8001_FAIL_DBG(pm8001_ha,
658                         pm8001_printk("Firmware is not ready!\n"));
659                 return -EBUSY;
660         }
661
662         /* Initialize pci space address eg: mpi offset */
663         init_pci_device_addresses(pm8001_ha);
664         init_default_table_values(pm8001_ha);
665         read_main_config_table(pm8001_ha);
666         read_general_status_table(pm8001_ha);
667         read_inbnd_queue_table(pm8001_ha);
668         read_outbnd_queue_table(pm8001_ha);
669         /* update main config table ,inbound table and outbound table */
670         update_main_config_table(pm8001_ha);
671         for (i = 0; i < PM8001_MAX_INB_NUM; i++)
672                 update_inbnd_queue_table(pm8001_ha, i);
673         for (i = 0; i < PM8001_MAX_OUTB_NUM; i++)
674                 update_outbnd_queue_table(pm8001_ha, i);
675         /* 8081 controller donot require these operations */
676         if (deviceid != 0x8081 && deviceid != 0x0042) {
677                 mpi_set_phys_g3_with_ssc(pm8001_ha, 0);
678                 /* 7->130ms, 34->500ms, 119->1.5s */
679                 mpi_set_open_retry_interval_reg(pm8001_ha, 119);
680         }
681         /* notify firmware update finished and check initialization status */
682         if (0 == mpi_init_check(pm8001_ha)) {
683                 PM8001_INIT_DBG(pm8001_ha,
684                         pm8001_printk("MPI initialize successful!\n"));
685         } else
686                 return -EBUSY;
687         /*This register is a 16-bit timer with a resolution of 1us. This is the
688         timer used for interrupt delay/coalescing in the PCIe Application Layer.
689         Zero is not a valid value. A value of 1 in the register will cause the
690         interrupts to be normal. A value greater than 1 will cause coalescing
691         delays.*/
692         pm8001_cw32(pm8001_ha, 1, 0x0033c0, 0x1);
693         pm8001_cw32(pm8001_ha, 1, 0x0033c4, 0x0);
694         return 0;
695 }
696
697 static int mpi_uninit_check(struct pm8001_hba_info *pm8001_ha)
698 {
699         u32 max_wait_count;
700         u32 value;
701         u32 gst_len_mpistate;
702         u16 deviceid;
703         pci_read_config_word(pm8001_ha->pdev, PCI_DEVICE_ID, &deviceid);
704         if (deviceid == 0x8081 || deviceid == 0x0042) {
705                 if (-1 == pm8001_bar4_shift(pm8001_ha, GSM_SM_BASE)) {
706                         PM8001_FAIL_DBG(pm8001_ha,
707                                 pm8001_printk("Shift Bar4 to 0x%x failed\n",
708                                         GSM_SM_BASE));
709                         return -1;
710                 }
711         }
712         init_pci_device_addresses(pm8001_ha);
713         /* Write bit1=1 to Inbound DoorBell Register to tell the SPC FW the
714         table is stop */
715         pm8001_cw32(pm8001_ha, 0, MSGU_IBDB_SET, SPC_MSGU_CFG_TABLE_RESET);
716
717         /* wait until Inbound DoorBell Clear Register toggled */
718         max_wait_count = 1 * 1000 * 1000;/* 1 sec */
719         do {
720                 udelay(1);
721                 value = pm8001_cr32(pm8001_ha, 0, MSGU_IBDB_SET);
722                 value &= SPC_MSGU_CFG_TABLE_RESET;
723         } while ((value != 0) && (--max_wait_count));
724
725         if (!max_wait_count) {
726                 PM8001_FAIL_DBG(pm8001_ha,
727                         pm8001_printk("TIMEOUT:IBDB value/=0x%x\n", value));
728                 return -1;
729         }
730
731         /* check the MPI-State for termination in progress */
732         /* wait until Inbound DoorBell Clear Register toggled */
733         max_wait_count = 1 * 1000 * 1000;  /* 1 sec */
734         do {
735                 udelay(1);
736                 gst_len_mpistate =
737                         pm8001_mr32(pm8001_ha->general_stat_tbl_addr,
738                         GST_GSTLEN_MPIS_OFFSET);
739                 if (GST_MPI_STATE_UNINIT ==
740                         (gst_len_mpistate & GST_MPI_STATE_MASK))
741                         break;
742         } while (--max_wait_count);
743         if (!max_wait_count) {
744                 PM8001_FAIL_DBG(pm8001_ha,
745                         pm8001_printk(" TIME OUT MPI State = 0x%x\n",
746                                 gst_len_mpistate & GST_MPI_STATE_MASK));
747                 return -1;
748         }
749         return 0;
750 }
751
752 /**
753  * soft_reset_ready_check - Function to check FW is ready for soft reset.
754  * @pm8001_ha: our hba card information
755  */
756 static u32 soft_reset_ready_check(struct pm8001_hba_info *pm8001_ha)
757 {
758         u32 regVal, regVal1, regVal2;
759         if (mpi_uninit_check(pm8001_ha) != 0) {
760                 PM8001_FAIL_DBG(pm8001_ha,
761                         pm8001_printk("MPI state is not ready\n"));
762                 return -1;
763         }
764         /* read the scratch pad 2 register bit 2 */
765         regVal = pm8001_cr32(pm8001_ha, 0, MSGU_SCRATCH_PAD_2)
766                 & SCRATCH_PAD2_FWRDY_RST;
767         if (regVal == SCRATCH_PAD2_FWRDY_RST) {
768                 PM8001_INIT_DBG(pm8001_ha,
769                         pm8001_printk("Firmware is ready for reset .\n"));
770         } else {
771                 unsigned long flags;
772                 /* Trigger NMI twice via RB6 */
773                 spin_lock_irqsave(&pm8001_ha->lock, flags);
774                 if (-1 == pm8001_bar4_shift(pm8001_ha, RB6_ACCESS_REG)) {
775                         spin_unlock_irqrestore(&pm8001_ha->lock, flags);
776                         PM8001_FAIL_DBG(pm8001_ha,
777                                 pm8001_printk("Shift Bar4 to 0x%x failed\n",
778                                         RB6_ACCESS_REG));
779                         return -1;
780                 }
781                 pm8001_cw32(pm8001_ha, 2, SPC_RB6_OFFSET,
782                         RB6_MAGIC_NUMBER_RST);
783                 pm8001_cw32(pm8001_ha, 2, SPC_RB6_OFFSET, RB6_MAGIC_NUMBER_RST);
784                 /* wait for 100 ms */
785                 mdelay(100);
786                 regVal = pm8001_cr32(pm8001_ha, 0, MSGU_SCRATCH_PAD_2) &
787                         SCRATCH_PAD2_FWRDY_RST;
788                 if (regVal != SCRATCH_PAD2_FWRDY_RST) {
789                         regVal1 = pm8001_cr32(pm8001_ha, 0, MSGU_SCRATCH_PAD_1);
790                         regVal2 = pm8001_cr32(pm8001_ha, 0, MSGU_SCRATCH_PAD_2);
791                         PM8001_FAIL_DBG(pm8001_ha,
792                                 pm8001_printk("TIMEOUT:MSGU_SCRATCH_PAD1"
793                                 "=0x%x, MSGU_SCRATCH_PAD2=0x%x\n",
794                                 regVal1, regVal2));
795                         PM8001_FAIL_DBG(pm8001_ha,
796                                 pm8001_printk("SCRATCH_PAD0 value = 0x%x\n",
797                                 pm8001_cr32(pm8001_ha, 0, MSGU_SCRATCH_PAD_0)));
798                         PM8001_FAIL_DBG(pm8001_ha,
799                                 pm8001_printk("SCRATCH_PAD3 value = 0x%x\n",
800                                 pm8001_cr32(pm8001_ha, 0, MSGU_SCRATCH_PAD_3)));
801                         spin_unlock_irqrestore(&pm8001_ha->lock, flags);
802                         return -1;
803                 }
804                 spin_unlock_irqrestore(&pm8001_ha->lock, flags);
805         }
806         return 0;
807 }
808
809 /**
810  * pm8001_chip_soft_rst - soft reset the PM8001 chip, so that the clear all
811  * the FW register status to the originated status.
812  * @pm8001_ha: our hba card information
813  */
814 static int
815 pm8001_chip_soft_rst(struct pm8001_hba_info *pm8001_ha)
816 {
817         u32     regVal, toggleVal;
818         u32     max_wait_count;
819         u32     regVal1, regVal2, regVal3;
820         u32     signature = 0x252acbcd; /* for host scratch pad0 */
821         unsigned long flags;
822
823         /* step1: Check FW is ready for soft reset */
824         if (soft_reset_ready_check(pm8001_ha) != 0) {
825                 PM8001_FAIL_DBG(pm8001_ha, pm8001_printk("FW is not ready\n"));
826                 return -1;
827         }
828
829         /* step 2: clear NMI status register on AAP1 and IOP, write the same
830         value to clear */
831         /* map 0x60000 to BAR4(0x20), BAR2(win) */
832         spin_lock_irqsave(&pm8001_ha->lock, flags);
833         if (-1 == pm8001_bar4_shift(pm8001_ha, MBIC_AAP1_ADDR_BASE)) {
834                 spin_unlock_irqrestore(&pm8001_ha->lock, flags);
835                 PM8001_FAIL_DBG(pm8001_ha,
836                         pm8001_printk("Shift Bar4 to 0x%x failed\n",
837                         MBIC_AAP1_ADDR_BASE));
838                 return -1;
839         }
840         regVal = pm8001_cr32(pm8001_ha, 2, MBIC_NMI_ENABLE_VPE0_IOP);
841         PM8001_INIT_DBG(pm8001_ha,
842                 pm8001_printk("MBIC - NMI Enable VPE0 (IOP)= 0x%x\n", regVal));
843         pm8001_cw32(pm8001_ha, 2, MBIC_NMI_ENABLE_VPE0_IOP, 0x0);
844         /* map 0x70000 to BAR4(0x20), BAR2(win) */
845         if (-1 == pm8001_bar4_shift(pm8001_ha, MBIC_IOP_ADDR_BASE)) {
846                 spin_unlock_irqrestore(&pm8001_ha->lock, flags);
847                 PM8001_FAIL_DBG(pm8001_ha,
848                         pm8001_printk("Shift Bar4 to 0x%x failed\n",
849                         MBIC_IOP_ADDR_BASE));
850                 return -1;
851         }
852         regVal = pm8001_cr32(pm8001_ha, 2, MBIC_NMI_ENABLE_VPE0_AAP1);
853         PM8001_INIT_DBG(pm8001_ha,
854                 pm8001_printk("MBIC - NMI Enable VPE0 (AAP1)= 0x%x\n", regVal));
855         pm8001_cw32(pm8001_ha, 2, MBIC_NMI_ENABLE_VPE0_AAP1, 0x0);
856
857         regVal = pm8001_cr32(pm8001_ha, 1, PCIE_EVENT_INTERRUPT_ENABLE);
858         PM8001_INIT_DBG(pm8001_ha,
859                 pm8001_printk("PCIE -Event Interrupt Enable = 0x%x\n", regVal));
860         pm8001_cw32(pm8001_ha, 1, PCIE_EVENT_INTERRUPT_ENABLE, 0x0);
861
862         regVal = pm8001_cr32(pm8001_ha, 1, PCIE_EVENT_INTERRUPT);
863         PM8001_INIT_DBG(pm8001_ha,
864                 pm8001_printk("PCIE - Event Interrupt  = 0x%x\n", regVal));
865         pm8001_cw32(pm8001_ha, 1, PCIE_EVENT_INTERRUPT, regVal);
866
867         regVal = pm8001_cr32(pm8001_ha, 1, PCIE_ERROR_INTERRUPT_ENABLE);
868         PM8001_INIT_DBG(pm8001_ha,
869                 pm8001_printk("PCIE -Error Interrupt Enable = 0x%x\n", regVal));
870         pm8001_cw32(pm8001_ha, 1, PCIE_ERROR_INTERRUPT_ENABLE, 0x0);
871
872         regVal = pm8001_cr32(pm8001_ha, 1, PCIE_ERROR_INTERRUPT);
873         PM8001_INIT_DBG(pm8001_ha,
874                 pm8001_printk("PCIE - Error Interrupt = 0x%x\n", regVal));
875         pm8001_cw32(pm8001_ha, 1, PCIE_ERROR_INTERRUPT, regVal);
876
877         /* read the scratch pad 1 register bit 2 */
878         regVal = pm8001_cr32(pm8001_ha, 0, MSGU_SCRATCH_PAD_1)
879                 & SCRATCH_PAD1_RST;
880         toggleVal = regVal ^ SCRATCH_PAD1_RST;
881
882         /* set signature in host scratch pad0 register to tell SPC that the
883         host performs the soft reset */
884         pm8001_cw32(pm8001_ha, 0, MSGU_HOST_SCRATCH_PAD_0, signature);
885
886         /* read required registers for confirmming */
887         /* map 0x0700000 to BAR4(0x20), BAR2(win) */
888         if (-1 == pm8001_bar4_shift(pm8001_ha, GSM_ADDR_BASE)) {
889                 spin_unlock_irqrestore(&pm8001_ha->lock, flags);
890                 PM8001_FAIL_DBG(pm8001_ha,
891                         pm8001_printk("Shift Bar4 to 0x%x failed\n",
892                         GSM_ADDR_BASE));
893                 return -1;
894         }
895         PM8001_INIT_DBG(pm8001_ha,
896                 pm8001_printk("GSM 0x0(0x00007b88)-GSM Configuration and"
897                 " Reset = 0x%x\n",
898                 pm8001_cr32(pm8001_ha, 2, GSM_CONFIG_RESET)));
899
900         /* step 3: host read GSM Configuration and Reset register */
901         regVal = pm8001_cr32(pm8001_ha, 2, GSM_CONFIG_RESET);
902         /* Put those bits to low */
903         /* GSM XCBI offset = 0x70 0000
904         0x00 Bit 13 COM_SLV_SW_RSTB 1
905         0x00 Bit 12 QSSP_SW_RSTB 1
906         0x00 Bit 11 RAAE_SW_RSTB 1
907         0x00 Bit 9 RB_1_SW_RSTB 1
908         0x00 Bit 8 SM_SW_RSTB 1
909         */
910         regVal &= ~(0x00003b00);
911         /* host write GSM Configuration and Reset register */
912         pm8001_cw32(pm8001_ha, 2, GSM_CONFIG_RESET, regVal);
913         PM8001_INIT_DBG(pm8001_ha,
914                 pm8001_printk("GSM 0x0 (0x00007b88 ==> 0x00004088) - GSM "
915                 "Configuration and Reset is set to = 0x%x\n",
916                 pm8001_cr32(pm8001_ha, 2, GSM_CONFIG_RESET)));
917
918         /* step 4: */
919         /* disable GSM - Read Address Parity Check */
920         regVal1 = pm8001_cr32(pm8001_ha, 2, GSM_READ_ADDR_PARITY_CHECK);
921         PM8001_INIT_DBG(pm8001_ha,
922                 pm8001_printk("GSM 0x700038 - Read Address Parity Check "
923                 "Enable = 0x%x\n", regVal1));
924         pm8001_cw32(pm8001_ha, 2, GSM_READ_ADDR_PARITY_CHECK, 0x0);
925         PM8001_INIT_DBG(pm8001_ha,
926                 pm8001_printk("GSM 0x700038 - Read Address Parity Check Enable"
927                 "is set to = 0x%x\n",
928                 pm8001_cr32(pm8001_ha, 2, GSM_READ_ADDR_PARITY_CHECK)));
929
930         /* disable GSM - Write Address Parity Check */
931         regVal2 = pm8001_cr32(pm8001_ha, 2, GSM_WRITE_ADDR_PARITY_CHECK);
932         PM8001_INIT_DBG(pm8001_ha,
933                 pm8001_printk("GSM 0x700040 - Write Address Parity Check"
934                 " Enable = 0x%x\n", regVal2));
935         pm8001_cw32(pm8001_ha, 2, GSM_WRITE_ADDR_PARITY_CHECK, 0x0);
936         PM8001_INIT_DBG(pm8001_ha,
937                 pm8001_printk("GSM 0x700040 - Write Address Parity Check "
938                 "Enable is set to = 0x%x\n",
939                 pm8001_cr32(pm8001_ha, 2, GSM_WRITE_ADDR_PARITY_CHECK)));
940
941         /* disable GSM - Write Data Parity Check */
942         regVal3 = pm8001_cr32(pm8001_ha, 2, GSM_WRITE_DATA_PARITY_CHECK);
943         PM8001_INIT_DBG(pm8001_ha,
944                 pm8001_printk("GSM 0x300048 - Write Data Parity Check"
945                 " Enable = 0x%x\n", regVal3));
946         pm8001_cw32(pm8001_ha, 2, GSM_WRITE_DATA_PARITY_CHECK, 0x0);
947         PM8001_INIT_DBG(pm8001_ha,
948                 pm8001_printk("GSM 0x300048 - Write Data Parity Check Enable"
949                 "is set to = 0x%x\n",
950         pm8001_cr32(pm8001_ha, 2, GSM_WRITE_DATA_PARITY_CHECK)));
951
952         /* step 5: delay 10 usec */
953         udelay(10);
954         /* step 5-b: set GPIO-0 output control to tristate anyway */
955         if (-1 == pm8001_bar4_shift(pm8001_ha, GPIO_ADDR_BASE)) {
956                 spin_unlock_irqrestore(&pm8001_ha->lock, flags);
957                 PM8001_INIT_DBG(pm8001_ha,
958                                 pm8001_printk("Shift Bar4 to 0x%x failed\n",
959                                 GPIO_ADDR_BASE));
960                 return -1;
961         }
962         regVal = pm8001_cr32(pm8001_ha, 2, GPIO_GPIO_0_0UTPUT_CTL_OFFSET);
963                 PM8001_INIT_DBG(pm8001_ha,
964                                 pm8001_printk("GPIO Output Control Register:"
965                                 " = 0x%x\n", regVal));
966         /* set GPIO-0 output control to tri-state */
967         regVal &= 0xFFFFFFFC;
968         pm8001_cw32(pm8001_ha, 2, GPIO_GPIO_0_0UTPUT_CTL_OFFSET, regVal);
969
970         /* Step 6: Reset the IOP and AAP1 */
971         /* map 0x00000 to BAR4(0x20), BAR2(win) */
972         if (-1 == pm8001_bar4_shift(pm8001_ha, SPC_TOP_LEVEL_ADDR_BASE)) {
973                 spin_unlock_irqrestore(&pm8001_ha->lock, flags);
974                 PM8001_FAIL_DBG(pm8001_ha,
975                         pm8001_printk("SPC Shift Bar4 to 0x%x failed\n",
976                         SPC_TOP_LEVEL_ADDR_BASE));
977                 return -1;
978         }
979         regVal = pm8001_cr32(pm8001_ha, 2, SPC_REG_RESET);
980         PM8001_INIT_DBG(pm8001_ha,
981                 pm8001_printk("Top Register before resetting IOP/AAP1"
982                 ":= 0x%x\n", regVal));
983         regVal &= ~(SPC_REG_RESET_PCS_IOP_SS | SPC_REG_RESET_PCS_AAP1_SS);
984         pm8001_cw32(pm8001_ha, 2, SPC_REG_RESET, regVal);
985
986         /* step 7: Reset the BDMA/OSSP */
987         regVal = pm8001_cr32(pm8001_ha, 2, SPC_REG_RESET);
988         PM8001_INIT_DBG(pm8001_ha,
989                 pm8001_printk("Top Register before resetting BDMA/OSSP"
990                 ": = 0x%x\n", regVal));
991         regVal &= ~(SPC_REG_RESET_BDMA_CORE | SPC_REG_RESET_OSSP);
992         pm8001_cw32(pm8001_ha, 2, SPC_REG_RESET, regVal);
993
994         /* step 8: delay 10 usec */
995         udelay(10);
996
997         /* step 9: bring the BDMA and OSSP out of reset */
998         regVal = pm8001_cr32(pm8001_ha, 2, SPC_REG_RESET);
999         PM8001_INIT_DBG(pm8001_ha,
1000                 pm8001_printk("Top Register before bringing up BDMA/OSSP"
1001                 ":= 0x%x\n", regVal));
1002         regVal |= (SPC_REG_RESET_BDMA_CORE | SPC_REG_RESET_OSSP);
1003         pm8001_cw32(pm8001_ha, 2, SPC_REG_RESET, regVal);
1004
1005         /* step 10: delay 10 usec */
1006         udelay(10);
1007
1008         /* step 11: reads and sets the GSM Configuration and Reset Register */
1009         /* map 0x0700000 to BAR4(0x20), BAR2(win) */
1010         if (-1 == pm8001_bar4_shift(pm8001_ha, GSM_ADDR_BASE)) {
1011                 spin_unlock_irqrestore(&pm8001_ha->lock, flags);
1012                 PM8001_FAIL_DBG(pm8001_ha,
1013                         pm8001_printk("SPC Shift Bar4 to 0x%x failed\n",
1014                         GSM_ADDR_BASE));
1015                 return -1;
1016         }
1017         PM8001_INIT_DBG(pm8001_ha,
1018                 pm8001_printk("GSM 0x0 (0x00007b88)-GSM Configuration and "
1019                 "Reset = 0x%x\n", pm8001_cr32(pm8001_ha, 2, GSM_CONFIG_RESET)));
1020         regVal = pm8001_cr32(pm8001_ha, 2, GSM_CONFIG_RESET);
1021         /* Put those bits to high */
1022         /* GSM XCBI offset = 0x70 0000
1023         0x00 Bit 13 COM_SLV_SW_RSTB 1
1024         0x00 Bit 12 QSSP_SW_RSTB 1
1025         0x00 Bit 11 RAAE_SW_RSTB 1
1026         0x00 Bit 9   RB_1_SW_RSTB 1
1027         0x00 Bit 8   SM_SW_RSTB 1
1028         */
1029         regVal |= (GSM_CONFIG_RESET_VALUE);
1030         pm8001_cw32(pm8001_ha, 2, GSM_CONFIG_RESET, regVal);
1031         PM8001_INIT_DBG(pm8001_ha,
1032                 pm8001_printk("GSM (0x00004088 ==> 0x00007b88) - GSM"
1033                 " Configuration and Reset is set to = 0x%x\n",
1034                 pm8001_cr32(pm8001_ha, 2, GSM_CONFIG_RESET)));
1035
1036         /* step 12: Restore GSM - Read Address Parity Check */
1037         regVal = pm8001_cr32(pm8001_ha, 2, GSM_READ_ADDR_PARITY_CHECK);
1038         /* just for debugging */
1039         PM8001_INIT_DBG(pm8001_ha,
1040                 pm8001_printk("GSM 0x700038 - Read Address Parity Check Enable"
1041                 " = 0x%x\n", regVal));
1042         pm8001_cw32(pm8001_ha, 2, GSM_READ_ADDR_PARITY_CHECK, regVal1);
1043         PM8001_INIT_DBG(pm8001_ha,
1044                 pm8001_printk("GSM 0x700038 - Read Address Parity"
1045                 " Check Enable is set to = 0x%x\n",
1046                 pm8001_cr32(pm8001_ha, 2, GSM_READ_ADDR_PARITY_CHECK)));
1047         /* Restore GSM - Write Address Parity Check */
1048         regVal = pm8001_cr32(pm8001_ha, 2, GSM_WRITE_ADDR_PARITY_CHECK);
1049         pm8001_cw32(pm8001_ha, 2, GSM_WRITE_ADDR_PARITY_CHECK, regVal2);
1050         PM8001_INIT_DBG(pm8001_ha,
1051                 pm8001_printk("GSM 0x700040 - Write Address Parity Check"
1052                 " Enable is set to = 0x%x\n",
1053                 pm8001_cr32(pm8001_ha, 2, GSM_WRITE_ADDR_PARITY_CHECK)));
1054         /* Restore GSM - Write Data Parity Check */
1055         regVal = pm8001_cr32(pm8001_ha, 2, GSM_WRITE_DATA_PARITY_CHECK);
1056         pm8001_cw32(pm8001_ha, 2, GSM_WRITE_DATA_PARITY_CHECK, regVal3);
1057         PM8001_INIT_DBG(pm8001_ha,
1058                 pm8001_printk("GSM 0x700048 - Write Data Parity Check Enable"
1059                 "is set to = 0x%x\n",
1060                 pm8001_cr32(pm8001_ha, 2, GSM_WRITE_DATA_PARITY_CHECK)));
1061
1062         /* step 13: bring the IOP and AAP1 out of reset */
1063         /* map 0x00000 to BAR4(0x20), BAR2(win) */
1064         if (-1 == pm8001_bar4_shift(pm8001_ha, SPC_TOP_LEVEL_ADDR_BASE)) {
1065                 spin_unlock_irqrestore(&pm8001_ha->lock, flags);
1066                 PM8001_FAIL_DBG(pm8001_ha,
1067                         pm8001_printk("Shift Bar4 to 0x%x failed\n",
1068                         SPC_TOP_LEVEL_ADDR_BASE));
1069                 return -1;
1070         }
1071         regVal = pm8001_cr32(pm8001_ha, 2, SPC_REG_RESET);
1072         regVal |= (SPC_REG_RESET_PCS_IOP_SS | SPC_REG_RESET_PCS_AAP1_SS);
1073         pm8001_cw32(pm8001_ha, 2, SPC_REG_RESET, regVal);
1074
1075         /* step 14: delay 10 usec - Normal Mode */
1076         udelay(10);
1077         /* check Soft Reset Normal mode or Soft Reset HDA mode */
1078         if (signature == SPC_SOFT_RESET_SIGNATURE) {
1079                 /* step 15 (Normal Mode): wait until scratch pad1 register
1080                 bit 2 toggled */
1081                 max_wait_count = 2 * 1000 * 1000;/* 2 sec */
1082                 do {
1083                         udelay(1);
1084                         regVal = pm8001_cr32(pm8001_ha, 0, MSGU_SCRATCH_PAD_1) &
1085                                 SCRATCH_PAD1_RST;
1086                 } while ((regVal != toggleVal) && (--max_wait_count));
1087
1088                 if (!max_wait_count) {
1089                         regVal = pm8001_cr32(pm8001_ha, 0,
1090                                 MSGU_SCRATCH_PAD_1);
1091                         PM8001_FAIL_DBG(pm8001_ha,
1092                                 pm8001_printk("TIMEOUT : ToggleVal 0x%x,"
1093                                 "MSGU_SCRATCH_PAD1 = 0x%x\n",
1094                                 toggleVal, regVal));
1095                         PM8001_FAIL_DBG(pm8001_ha,
1096                                 pm8001_printk("SCRATCH_PAD0 value = 0x%x\n",
1097                                 pm8001_cr32(pm8001_ha, 0,
1098                                 MSGU_SCRATCH_PAD_0)));
1099                         PM8001_FAIL_DBG(pm8001_ha,
1100                                 pm8001_printk("SCRATCH_PAD2 value = 0x%x\n",
1101                                 pm8001_cr32(pm8001_ha, 0,
1102                                 MSGU_SCRATCH_PAD_2)));
1103                         PM8001_FAIL_DBG(pm8001_ha,
1104                                 pm8001_printk("SCRATCH_PAD3 value = 0x%x\n",
1105                                 pm8001_cr32(pm8001_ha, 0,
1106                                 MSGU_SCRATCH_PAD_3)));
1107                         spin_unlock_irqrestore(&pm8001_ha->lock, flags);
1108                         return -1;
1109                 }
1110
1111                 /* step 16 (Normal) - Clear ODMR and ODCR */
1112                 pm8001_cw32(pm8001_ha, 0, MSGU_ODCR, ODCR_CLEAR_ALL);
1113                 pm8001_cw32(pm8001_ha, 0, MSGU_ODMR, ODMR_CLEAR_ALL);
1114
1115                 /* step 17 (Normal Mode): wait for the FW and IOP to get
1116                 ready - 1 sec timeout */
1117                 /* Wait for the SPC Configuration Table to be ready */
1118                 if (check_fw_ready(pm8001_ha) == -1) {
1119                         regVal = pm8001_cr32(pm8001_ha, 0, MSGU_SCRATCH_PAD_1);
1120                         /* return error if MPI Configuration Table not ready */
1121                         PM8001_INIT_DBG(pm8001_ha,
1122                                 pm8001_printk("FW not ready SCRATCH_PAD1"
1123                                 " = 0x%x\n", regVal));
1124                         regVal = pm8001_cr32(pm8001_ha, 0, MSGU_SCRATCH_PAD_2);
1125                         /* return error if MPI Configuration Table not ready */
1126                         PM8001_INIT_DBG(pm8001_ha,
1127                                 pm8001_printk("FW not ready SCRATCH_PAD2"
1128                                 " = 0x%x\n", regVal));
1129                         PM8001_INIT_DBG(pm8001_ha,
1130                                 pm8001_printk("SCRATCH_PAD0 value = 0x%x\n",
1131                                 pm8001_cr32(pm8001_ha, 0,
1132                                 MSGU_SCRATCH_PAD_0)));
1133                         PM8001_INIT_DBG(pm8001_ha,
1134                                 pm8001_printk("SCRATCH_PAD3 value = 0x%x\n",
1135                                 pm8001_cr32(pm8001_ha, 0,
1136                                 MSGU_SCRATCH_PAD_3)));
1137                         spin_unlock_irqrestore(&pm8001_ha->lock, flags);
1138                         return -1;
1139                 }
1140         }
1141         pm8001_bar4_shift(pm8001_ha, 0);
1142         spin_unlock_irqrestore(&pm8001_ha->lock, flags);
1143
1144         PM8001_INIT_DBG(pm8001_ha,
1145                 pm8001_printk("SPC soft reset Complete\n"));
1146         return 0;
1147 }
1148
1149 static void pm8001_hw_chip_rst(struct pm8001_hba_info *pm8001_ha)
1150 {
1151         u32 i;
1152         u32 regVal;
1153         PM8001_INIT_DBG(pm8001_ha,
1154                 pm8001_printk("chip reset start\n"));
1155
1156         /* do SPC chip reset. */
1157         regVal = pm8001_cr32(pm8001_ha, 1, SPC_REG_RESET);
1158         regVal &= ~(SPC_REG_RESET_DEVICE);
1159         pm8001_cw32(pm8001_ha, 1, SPC_REG_RESET, regVal);
1160
1161         /* delay 10 usec */
1162         udelay(10);
1163
1164         /* bring chip reset out of reset */
1165         regVal = pm8001_cr32(pm8001_ha, 1, SPC_REG_RESET);
1166         regVal |= SPC_REG_RESET_DEVICE;
1167         pm8001_cw32(pm8001_ha, 1, SPC_REG_RESET, regVal);
1168
1169         /* delay 10 usec */
1170         udelay(10);
1171
1172         /* wait for 20 msec until the firmware gets reloaded */
1173         i = 20;
1174         do {
1175                 mdelay(1);
1176         } while ((--i) != 0);
1177
1178         PM8001_INIT_DBG(pm8001_ha,
1179                 pm8001_printk("chip reset finished\n"));
1180 }
1181
1182 /**
1183  * pm8001_chip_iounmap - which maped when initialized.
1184  * @pm8001_ha: our hba card information
1185  */
1186 void pm8001_chip_iounmap(struct pm8001_hba_info *pm8001_ha)
1187 {
1188         s8 bar, logical = 0;
1189         for (bar = 0; bar < 6; bar++) {
1190                 /*
1191                 ** logical BARs for SPC:
1192                 ** bar 0 and 1 - logical BAR0
1193                 ** bar 2 and 3 - logical BAR1
1194                 ** bar4 - logical BAR2
1195                 ** bar5 - logical BAR3
1196                 ** Skip the appropriate assignments:
1197                 */
1198                 if ((bar == 1) || (bar == 3))
1199                         continue;
1200                 if (pm8001_ha->io_mem[logical].memvirtaddr) {
1201                         iounmap(pm8001_ha->io_mem[logical].memvirtaddr);
1202                         logical++;
1203                 }
1204         }
1205 }
1206
1207 /**
1208  * pm8001_chip_interrupt_enable - enable PM8001 chip interrupt
1209  * @pm8001_ha: our hba card information
1210  */
1211 static void
1212 pm8001_chip_intx_interrupt_enable(struct pm8001_hba_info *pm8001_ha)
1213 {
1214         pm8001_cw32(pm8001_ha, 0, MSGU_ODMR, ODMR_CLEAR_ALL);
1215         pm8001_cw32(pm8001_ha, 0, MSGU_ODCR, ODCR_CLEAR_ALL);
1216 }
1217
1218  /**
1219   * pm8001_chip_intx_interrupt_disable- disable PM8001 chip interrupt
1220   * @pm8001_ha: our hba card information
1221   */
1222 static void
1223 pm8001_chip_intx_interrupt_disable(struct pm8001_hba_info *pm8001_ha)
1224 {
1225         pm8001_cw32(pm8001_ha, 0, MSGU_ODMR, ODMR_MASK_ALL);
1226 }
1227
1228 /**
1229  * pm8001_chip_msix_interrupt_enable - enable PM8001 chip interrupt
1230  * @pm8001_ha: our hba card information
1231  */
1232 static void
1233 pm8001_chip_msix_interrupt_enable(struct pm8001_hba_info *pm8001_ha,
1234         u32 int_vec_idx)
1235 {
1236         u32 msi_index;
1237         u32 value;
1238         msi_index = int_vec_idx * MSIX_TABLE_ELEMENT_SIZE;
1239         msi_index += MSIX_TABLE_BASE;
1240         pm8001_cw32(pm8001_ha, 0, msi_index, MSIX_INTERRUPT_ENABLE);
1241         value = (1 << int_vec_idx);
1242         pm8001_cw32(pm8001_ha, 0,  MSGU_ODCR, value);
1243
1244 }
1245
1246 /**
1247  * pm8001_chip_msix_interrupt_disable - disable PM8001 chip interrupt
1248  * @pm8001_ha: our hba card information
1249  */
1250 static void
1251 pm8001_chip_msix_interrupt_disable(struct pm8001_hba_info *pm8001_ha,
1252         u32 int_vec_idx)
1253 {
1254         u32 msi_index;
1255         msi_index = int_vec_idx * MSIX_TABLE_ELEMENT_SIZE;
1256         msi_index += MSIX_TABLE_BASE;
1257         pm8001_cw32(pm8001_ha, 0,  msi_index, MSIX_INTERRUPT_DISABLE);
1258 }
1259
1260 /**
1261  * pm8001_chip_interrupt_enable - enable PM8001 chip interrupt
1262  * @pm8001_ha: our hba card information
1263  */
1264 static void
1265 pm8001_chip_interrupt_enable(struct pm8001_hba_info *pm8001_ha, u8 vec)
1266 {
1267 #ifdef PM8001_USE_MSIX
1268         pm8001_chip_msix_interrupt_enable(pm8001_ha, 0);
1269         return;
1270 #endif
1271         pm8001_chip_intx_interrupt_enable(pm8001_ha);
1272
1273 }
1274
1275 /**
1276  * pm8001_chip_intx_interrupt_disable- disable PM8001 chip interrupt
1277  * @pm8001_ha: our hba card information
1278  */
1279 static void
1280 pm8001_chip_interrupt_disable(struct pm8001_hba_info *pm8001_ha, u8 vec)
1281 {
1282 #ifdef PM8001_USE_MSIX
1283         pm8001_chip_msix_interrupt_disable(pm8001_ha, 0);
1284         return;
1285 #endif
1286         pm8001_chip_intx_interrupt_disable(pm8001_ha);
1287
1288 }
1289
1290 /**
1291  * pm8001_mpi_msg_free_get - get the free message buffer for transfer
1292  * inbound queue.
1293  * @circularQ: the inbound queue  we want to transfer to HBA.
1294  * @messageSize: the message size of this transfer, normally it is 64 bytes
1295  * @messagePtr: the pointer to message.
1296  */
1297 int pm8001_mpi_msg_free_get(struct inbound_queue_table *circularQ,
1298                             u16 messageSize, void **messagePtr)
1299 {
1300         u32 offset, consumer_index;
1301         struct mpi_msg_hdr *msgHeader;
1302         u8 bcCount = 1; /* only support single buffer */
1303
1304         /* Checks is the requested message size can be allocated in this queue*/
1305         if (messageSize > IOMB_SIZE_SPCV) {
1306                 *messagePtr = NULL;
1307                 return -1;
1308         }
1309
1310         /* Stores the new consumer index */
1311         consumer_index = pm8001_read_32(circularQ->ci_virt);
1312         circularQ->consumer_index = cpu_to_le32(consumer_index);
1313         if (((circularQ->producer_idx + bcCount) % PM8001_MPI_QUEUE) ==
1314                 le32_to_cpu(circularQ->consumer_index)) {
1315                 *messagePtr = NULL;
1316                 return -1;
1317         }
1318         /* get memory IOMB buffer address */
1319         offset = circularQ->producer_idx * messageSize;
1320         /* increment to next bcCount element */
1321         circularQ->producer_idx = (circularQ->producer_idx + bcCount)
1322                                 % PM8001_MPI_QUEUE;
1323         /* Adds that distance to the base of the region virtual address plus
1324         the message header size*/
1325         msgHeader = (struct mpi_msg_hdr *)(circularQ->base_virt + offset);
1326         *messagePtr = ((void *)msgHeader) + sizeof(struct mpi_msg_hdr);
1327         return 0;
1328 }
1329
1330 /**
1331  * pm8001_mpi_build_cmd- build the message queue for transfer, update the PI to
1332  * FW to tell the fw to get this message from IOMB.
1333  * @pm8001_ha: our hba card information
1334  * @circularQ: the inbound queue we want to transfer to HBA.
1335  * @opCode: the operation code represents commands which LLDD and fw recognized.
1336  * @payload: the command payload of each operation command.
1337  */
1338 int pm8001_mpi_build_cmd(struct pm8001_hba_info *pm8001_ha,
1339                          struct inbound_queue_table *circularQ,
1340                          u32 opCode, void *payload, u32 responseQueue)
1341 {
1342         u32 Header = 0, hpriority = 0, bc = 1, category = 0x02;
1343         void *pMessage;
1344
1345         if (pm8001_mpi_msg_free_get(circularQ, pm8001_ha->iomb_size,
1346                 &pMessage) < 0) {
1347                 PM8001_IO_DBG(pm8001_ha,
1348                         pm8001_printk("No free mpi buffer\n"));
1349                 return -ENOMEM;
1350         }
1351         BUG_ON(!payload);
1352         /*Copy to the payload*/
1353         memcpy(pMessage, payload, (pm8001_ha->iomb_size -
1354                                 sizeof(struct mpi_msg_hdr)));
1355
1356         /*Build the header*/
1357         Header = ((1 << 31) | (hpriority << 30) | ((bc & 0x1f) << 24)
1358                 | ((responseQueue & 0x3F) << 16)
1359                 | ((category & 0xF) << 12) | (opCode & 0xFFF));
1360
1361         pm8001_write_32((pMessage - 4), 0, cpu_to_le32(Header));
1362         /*Update the PI to the firmware*/
1363         pm8001_cw32(pm8001_ha, circularQ->pi_pci_bar,
1364                 circularQ->pi_offset, circularQ->producer_idx);
1365         PM8001_IO_DBG(pm8001_ha,
1366                 pm8001_printk("INB Q %x OPCODE:%x , UPDATED PI=%d CI=%d\n",
1367                         responseQueue, opCode, circularQ->producer_idx,
1368                         circularQ->consumer_index));
1369         return 0;
1370 }
1371
1372 u32 pm8001_mpi_msg_free_set(struct pm8001_hba_info *pm8001_ha, void *pMsg,
1373                             struct outbound_queue_table *circularQ, u8 bc)
1374 {
1375         u32 producer_index;
1376         struct mpi_msg_hdr *msgHeader;
1377         struct mpi_msg_hdr *pOutBoundMsgHeader;
1378
1379         msgHeader = (struct mpi_msg_hdr *)(pMsg - sizeof(struct mpi_msg_hdr));
1380         pOutBoundMsgHeader = (struct mpi_msg_hdr *)(circularQ->base_virt +
1381                                 circularQ->consumer_idx * pm8001_ha->iomb_size);
1382         if (pOutBoundMsgHeader != msgHeader) {
1383                 PM8001_FAIL_DBG(pm8001_ha,
1384                         pm8001_printk("consumer_idx = %d msgHeader = %p\n",
1385                         circularQ->consumer_idx, msgHeader));
1386
1387                 /* Update the producer index from SPC */
1388                 producer_index = pm8001_read_32(circularQ->pi_virt);
1389                 circularQ->producer_index = cpu_to_le32(producer_index);
1390                 PM8001_FAIL_DBG(pm8001_ha,
1391                         pm8001_printk("consumer_idx = %d producer_index = %d"
1392                         "msgHeader = %p\n", circularQ->consumer_idx,
1393                         circularQ->producer_index, msgHeader));
1394                 return 0;
1395         }
1396         /* free the circular queue buffer elements associated with the message*/
1397         circularQ->consumer_idx = (circularQ->consumer_idx + bc)
1398                                 % PM8001_MPI_QUEUE;
1399         /* update the CI of outbound queue */
1400         pm8001_cw32(pm8001_ha, circularQ->ci_pci_bar, circularQ->ci_offset,
1401                 circularQ->consumer_idx);
1402         /* Update the producer index from SPC*/
1403         producer_index = pm8001_read_32(circularQ->pi_virt);
1404         circularQ->producer_index = cpu_to_le32(producer_index);
1405         PM8001_IO_DBG(pm8001_ha,
1406                 pm8001_printk(" CI=%d PI=%d\n", circularQ->consumer_idx,
1407                 circularQ->producer_index));
1408         return 0;
1409 }
1410
1411 /**
1412  * pm8001_mpi_msg_consume- get the MPI message from outbound queue
1413  * message table.
1414  * @pm8001_ha: our hba card information
1415  * @circularQ: the outbound queue  table.
1416  * @messagePtr1: the message contents of this outbound message.
1417  * @pBC: the message size.
1418  */
1419 u32 pm8001_mpi_msg_consume(struct pm8001_hba_info *pm8001_ha,
1420                            struct outbound_queue_table *circularQ,
1421                            void **messagePtr1, u8 *pBC)
1422 {
1423         struct mpi_msg_hdr      *msgHeader;
1424         __le32  msgHeader_tmp;
1425         u32 header_tmp;
1426         do {
1427                 /* If there are not-yet-delivered messages ... */
1428                 if (le32_to_cpu(circularQ->producer_index)
1429                         != circularQ->consumer_idx) {
1430                         /*Get the pointer to the circular queue buffer element*/
1431                         msgHeader = (struct mpi_msg_hdr *)
1432                                 (circularQ->base_virt +
1433                                 circularQ->consumer_idx * pm8001_ha->iomb_size);
1434                         /* read header */
1435                         header_tmp = pm8001_read_32(msgHeader);
1436                         msgHeader_tmp = cpu_to_le32(header_tmp);
1437                         if (0 != (le32_to_cpu(msgHeader_tmp) & 0x80000000)) {
1438                                 if (OPC_OUB_SKIP_ENTRY !=
1439                                         (le32_to_cpu(msgHeader_tmp) & 0xfff)) {
1440                                         *messagePtr1 =
1441                                                 ((u8 *)msgHeader) +
1442                                                 sizeof(struct mpi_msg_hdr);
1443                                         *pBC = (u8)((le32_to_cpu(msgHeader_tmp)
1444                                                 >> 24) & 0x1f);
1445                                         PM8001_IO_DBG(pm8001_ha,
1446                                                 pm8001_printk(": CI=%d PI=%d "
1447                                                 "msgHeader=%x\n",
1448                                                 circularQ->consumer_idx,
1449                                                 circularQ->producer_index,
1450                                                 msgHeader_tmp));
1451                                         return MPI_IO_STATUS_SUCCESS;
1452                                 } else {
1453                                         circularQ->consumer_idx =
1454                                                 (circularQ->consumer_idx +
1455                                                 ((le32_to_cpu(msgHeader_tmp)
1456                                                  >> 24) & 0x1f))
1457                                                         % PM8001_MPI_QUEUE;
1458                                         msgHeader_tmp = 0;
1459                                         pm8001_write_32(msgHeader, 0, 0);
1460                                         /* update the CI of outbound queue */
1461                                         pm8001_cw32(pm8001_ha,
1462                                                 circularQ->ci_pci_bar,
1463                                                 circularQ->ci_offset,
1464                                                 circularQ->consumer_idx);
1465                                 }
1466                         } else {
1467                                 circularQ->consumer_idx =
1468                                         (circularQ->consumer_idx +
1469                                         ((le32_to_cpu(msgHeader_tmp) >> 24) &
1470                                         0x1f)) % PM8001_MPI_QUEUE;
1471                                 msgHeader_tmp = 0;
1472                                 pm8001_write_32(msgHeader, 0, 0);
1473                                 /* update the CI of outbound queue */
1474                                 pm8001_cw32(pm8001_ha, circularQ->ci_pci_bar,
1475                                         circularQ->ci_offset,
1476                                         circularQ->consumer_idx);
1477                                 return MPI_IO_STATUS_FAIL;
1478                         }
1479                 } else {
1480                         u32 producer_index;
1481                         void *pi_virt = circularQ->pi_virt;
1482                         /* Update the producer index from SPC */
1483                         producer_index = pm8001_read_32(pi_virt);
1484                         circularQ->producer_index = cpu_to_le32(producer_index);
1485                 }
1486         } while (le32_to_cpu(circularQ->producer_index) !=
1487                 circularQ->consumer_idx);
1488         /* while we don't have any more not-yet-delivered message */
1489         /* report empty */
1490         return MPI_IO_STATUS_BUSY;
1491 }
1492
1493 void pm8001_work_fn(struct work_struct *work)
1494 {
1495         struct pm8001_work *pw = container_of(work, struct pm8001_work, work);
1496         struct pm8001_device *pm8001_dev;
1497         struct domain_device *dev;
1498
1499         /*
1500          * So far, all users of this stash an associated structure here.
1501          * If we get here, and this pointer is null, then the action
1502          * was cancelled. This nullification happens when the device
1503          * goes away.
1504          */
1505         pm8001_dev = pw->data; /* Most stash device structure */
1506         if ((pm8001_dev == NULL)
1507          || ((pw->handler != IO_XFER_ERROR_BREAK)
1508           && (pm8001_dev->dev_type == SAS_PHY_UNUSED))) {
1509                 kfree(pw);
1510                 return;
1511         }
1512
1513         switch (pw->handler) {
1514         case IO_XFER_ERROR_BREAK:
1515         {       /* This one stashes the sas_task instead */
1516                 struct sas_task *t = (struct sas_task *)pm8001_dev;
1517                 u32 tag;
1518                 struct pm8001_ccb_info *ccb;
1519                 struct pm8001_hba_info *pm8001_ha = pw->pm8001_ha;
1520                 unsigned long flags, flags1;
1521                 struct task_status_struct *ts;
1522                 int i;
1523
1524                 if (pm8001_query_task(t) == TMF_RESP_FUNC_SUCC)
1525                         break; /* Task still on lu */
1526                 spin_lock_irqsave(&pm8001_ha->lock, flags);
1527
1528                 spin_lock_irqsave(&t->task_state_lock, flags1);
1529                 if (unlikely((t->task_state_flags & SAS_TASK_STATE_DONE))) {
1530                         spin_unlock_irqrestore(&t->task_state_lock, flags1);
1531                         spin_unlock_irqrestore(&pm8001_ha->lock, flags);
1532                         break; /* Task got completed by another */
1533                 }
1534                 spin_unlock_irqrestore(&t->task_state_lock, flags1);
1535
1536                 /* Search for a possible ccb that matches the task */
1537                 for (i = 0; ccb = NULL, i < PM8001_MAX_CCB; i++) {
1538                         ccb = &pm8001_ha->ccb_info[i];
1539                         tag = ccb->ccb_tag;
1540                         if ((tag != 0xFFFFFFFF) && (ccb->task == t))
1541                                 break;
1542                 }
1543                 if (!ccb) {
1544                         spin_unlock_irqrestore(&pm8001_ha->lock, flags);
1545                         break; /* Task got freed by another */
1546                 }
1547                 ts = &t->task_status;
1548                 ts->resp = SAS_TASK_COMPLETE;
1549                 /* Force the midlayer to retry */
1550                 ts->stat = SAS_QUEUE_FULL;
1551                 pm8001_dev = ccb->device;
1552                 if (pm8001_dev)
1553                         pm8001_dev->running_req--;
1554                 spin_lock_irqsave(&t->task_state_lock, flags1);
1555                 t->task_state_flags &= ~SAS_TASK_STATE_PENDING;
1556                 t->task_state_flags &= ~SAS_TASK_AT_INITIATOR;
1557                 t->task_state_flags |= SAS_TASK_STATE_DONE;
1558                 if (unlikely((t->task_state_flags & SAS_TASK_STATE_ABORTED))) {
1559                         spin_unlock_irqrestore(&t->task_state_lock, flags1);
1560                         PM8001_FAIL_DBG(pm8001_ha, pm8001_printk("task 0x%p"
1561                                 " done with event 0x%x resp 0x%x stat 0x%x but"
1562                                 " aborted by upper layer!\n",
1563                                 t, pw->handler, ts->resp, ts->stat));
1564                         pm8001_ccb_task_free(pm8001_ha, t, ccb, tag);
1565                         spin_unlock_irqrestore(&pm8001_ha->lock, flags);
1566                 } else {
1567                         spin_unlock_irqrestore(&t->task_state_lock, flags1);
1568                         pm8001_ccb_task_free(pm8001_ha, t, ccb, tag);
1569                         mb();/* in order to force CPU ordering */
1570                         spin_unlock_irqrestore(&pm8001_ha->lock, flags);
1571                         t->task_done(t);
1572                 }
1573         }       break;
1574         case IO_XFER_OPEN_RETRY_TIMEOUT:
1575         {       /* This one stashes the sas_task instead */
1576                 struct sas_task *t = (struct sas_task *)pm8001_dev;
1577                 u32 tag;
1578                 struct pm8001_ccb_info *ccb;
1579                 struct pm8001_hba_info *pm8001_ha = pw->pm8001_ha;
1580                 unsigned long flags, flags1;
1581                 int i, ret = 0;
1582
1583                 PM8001_IO_DBG(pm8001_ha,
1584                         pm8001_printk("IO_XFER_OPEN_RETRY_TIMEOUT\n"));
1585
1586                 ret = pm8001_query_task(t);
1587
1588                 PM8001_IO_DBG(pm8001_ha,
1589                         switch (ret) {
1590                         case TMF_RESP_FUNC_SUCC:
1591                                 pm8001_printk("...Task on lu\n");
1592                                 break;
1593
1594                         case TMF_RESP_FUNC_COMPLETE:
1595                                 pm8001_printk("...Task NOT on lu\n");
1596                                 break;
1597
1598                         default:
1599                                 pm8001_printk("...query task failed!!!\n");
1600                                 break;
1601                         });
1602
1603                 spin_lock_irqsave(&pm8001_ha->lock, flags);
1604
1605                 spin_lock_irqsave(&t->task_state_lock, flags1);
1606
1607                 if (unlikely((t->task_state_flags & SAS_TASK_STATE_DONE))) {
1608                         spin_unlock_irqrestore(&t->task_state_lock, flags1);
1609                         spin_unlock_irqrestore(&pm8001_ha->lock, flags);
1610                         if (ret == TMF_RESP_FUNC_SUCC) /* task on lu */
1611                                 (void)pm8001_abort_task(t);
1612                         break; /* Task got completed by another */
1613                 }
1614
1615                 spin_unlock_irqrestore(&t->task_state_lock, flags1);
1616
1617                 /* Search for a possible ccb that matches the task */
1618                 for (i = 0; ccb = NULL, i < PM8001_MAX_CCB; i++) {
1619                         ccb = &pm8001_ha->ccb_info[i];
1620                         tag = ccb->ccb_tag;
1621                         if ((tag != 0xFFFFFFFF) && (ccb->task == t))
1622                                 break;
1623                 }
1624                 if (!ccb) {
1625                         spin_unlock_irqrestore(&pm8001_ha->lock, flags);
1626                         if (ret == TMF_RESP_FUNC_SUCC) /* task on lu */
1627                                 (void)pm8001_abort_task(t);
1628                         break; /* Task got freed by another */
1629                 }
1630
1631                 pm8001_dev = ccb->device;
1632                 dev = pm8001_dev->sas_device;
1633
1634                 switch (ret) {
1635                 case TMF_RESP_FUNC_SUCC: /* task on lu */
1636                         ccb->open_retry = 1; /* Snub completion */
1637                         spin_unlock_irqrestore(&pm8001_ha->lock, flags);
1638                         ret = pm8001_abort_task(t);
1639                         ccb->open_retry = 0;
1640                         switch (ret) {
1641                         case TMF_RESP_FUNC_SUCC:
1642                         case TMF_RESP_FUNC_COMPLETE:
1643                                 break;
1644                         default: /* device misbehavior */
1645                                 ret = TMF_RESP_FUNC_FAILED;
1646                                 PM8001_IO_DBG(pm8001_ha,
1647                                         pm8001_printk("...Reset phy\n"));
1648                                 pm8001_I_T_nexus_reset(dev);
1649                                 break;
1650                         }
1651                         break;
1652
1653                 case TMF_RESP_FUNC_COMPLETE: /* task not on lu */
1654                         spin_unlock_irqrestore(&pm8001_ha->lock, flags);
1655                         /* Do we need to abort the task locally? */
1656                         break;
1657
1658                 default: /* device misbehavior */
1659                         spin_unlock_irqrestore(&pm8001_ha->lock, flags);
1660                         ret = TMF_RESP_FUNC_FAILED;
1661                         PM8001_IO_DBG(pm8001_ha,
1662                                 pm8001_printk("...Reset phy\n"));
1663                         pm8001_I_T_nexus_reset(dev);
1664                 }
1665
1666                 if (ret == TMF_RESP_FUNC_FAILED)
1667                         t = NULL;
1668                 pm8001_open_reject_retry(pm8001_ha, t, pm8001_dev);
1669                 PM8001_IO_DBG(pm8001_ha, pm8001_printk("...Complete\n"));
1670         }       break;
1671         case IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS:
1672                 dev = pm8001_dev->sas_device;
1673                 pm8001_I_T_nexus_event_handler(dev);
1674                 break;
1675         case IO_OPEN_CNX_ERROR_STP_RESOURCES_BUSY:
1676                 dev = pm8001_dev->sas_device;
1677                 pm8001_I_T_nexus_reset(dev);
1678                 break;
1679         case IO_DS_IN_ERROR:
1680                 dev = pm8001_dev->sas_device;
1681                 pm8001_I_T_nexus_reset(dev);
1682                 break;
1683         case IO_DS_NON_OPERATIONAL:
1684                 dev = pm8001_dev->sas_device;
1685                 pm8001_I_T_nexus_reset(dev);
1686                 break;
1687         }
1688         kfree(pw);
1689 }
1690
1691 int pm8001_handle_event(struct pm8001_hba_info *pm8001_ha, void *data,
1692                                int handler)
1693 {
1694         struct pm8001_work *pw;
1695         int ret = 0;
1696
1697         pw = kmalloc(sizeof(struct pm8001_work), GFP_ATOMIC);
1698         if (pw) {
1699                 pw->pm8001_ha = pm8001_ha;
1700                 pw->data = data;
1701                 pw->handler = handler;
1702                 INIT_WORK(&pw->work, pm8001_work_fn);
1703                 queue_work(pm8001_wq, &pw->work);
1704         } else
1705                 ret = -ENOMEM;
1706
1707         return ret;
1708 }
1709
1710 static void pm8001_send_abort_all(struct pm8001_hba_info *pm8001_ha,
1711                 struct pm8001_device *pm8001_ha_dev)
1712 {
1713         int res;
1714         u32 ccb_tag;
1715         struct pm8001_ccb_info *ccb;
1716         struct sas_task *task = NULL;
1717         struct task_abort_req task_abort;
1718         struct inbound_queue_table *circularQ;
1719         u32 opc = OPC_INB_SATA_ABORT;
1720         int ret;
1721
1722         if (!pm8001_ha_dev) {
1723                 PM8001_FAIL_DBG(pm8001_ha, pm8001_printk("dev is null\n"));
1724                 return;
1725         }
1726
1727         task = sas_alloc_slow_task(GFP_ATOMIC);
1728
1729         if (!task) {
1730                 PM8001_FAIL_DBG(pm8001_ha, pm8001_printk("cannot "
1731                                                 "allocate task\n"));
1732                 return;
1733         }
1734
1735         task->task_done = pm8001_task_done;
1736
1737         res = pm8001_tag_alloc(pm8001_ha, &ccb_tag);
1738         if (res)
1739                 return;
1740
1741         ccb = &pm8001_ha->ccb_info[ccb_tag];
1742         ccb->device = pm8001_ha_dev;
1743         ccb->ccb_tag = ccb_tag;
1744         ccb->task = task;
1745
1746         circularQ = &pm8001_ha->inbnd_q_tbl[0];
1747
1748         memset(&task_abort, 0, sizeof(task_abort));
1749         task_abort.abort_all = cpu_to_le32(1);
1750         task_abort.device_id = cpu_to_le32(pm8001_ha_dev->device_id);
1751         task_abort.tag = cpu_to_le32(ccb_tag);
1752
1753         ret = pm8001_mpi_build_cmd(pm8001_ha, circularQ, opc, &task_abort, 0);
1754         if (ret)
1755                 pm8001_tag_free(pm8001_ha, ccb_tag);
1756
1757 }
1758
1759 static void pm8001_send_read_log(struct pm8001_hba_info *pm8001_ha,
1760                 struct pm8001_device *pm8001_ha_dev)
1761 {
1762         struct sata_start_req sata_cmd;
1763         int res;
1764         u32 ccb_tag;
1765         struct pm8001_ccb_info *ccb;
1766         struct sas_task *task = NULL;
1767         struct host_to_dev_fis fis;
1768         struct domain_device *dev;
1769         struct inbound_queue_table *circularQ;
1770         u32 opc = OPC_INB_SATA_HOST_OPSTART;
1771
1772         task = sas_alloc_slow_task(GFP_ATOMIC);
1773
1774         if (!task) {
1775                 PM8001_FAIL_DBG(pm8001_ha,
1776                         pm8001_printk("cannot allocate task !!!\n"));
1777                 return;
1778         }
1779         task->task_done = pm8001_task_done;
1780
1781         res = pm8001_tag_alloc(pm8001_ha, &ccb_tag);
1782         if (res) {
1783                 sas_free_task(task);
1784                 PM8001_FAIL_DBG(pm8001_ha,
1785                         pm8001_printk("cannot allocate tag !!!\n"));
1786                 return;
1787         }
1788
1789         /* allocate domain device by ourselves as libsas
1790          * is not going to provide any
1791         */
1792         dev = kzalloc(sizeof(struct domain_device), GFP_ATOMIC);
1793         if (!dev) {
1794                 sas_free_task(task);
1795                 pm8001_tag_free(pm8001_ha, ccb_tag);
1796                 PM8001_FAIL_DBG(pm8001_ha,
1797                         pm8001_printk("Domain device cannot be allocated\n"));
1798                 return;
1799         }
1800         task->dev = dev;
1801         task->dev->lldd_dev = pm8001_ha_dev;
1802
1803         ccb = &pm8001_ha->ccb_info[ccb_tag];
1804         ccb->device = pm8001_ha_dev;
1805         ccb->ccb_tag = ccb_tag;
1806         ccb->task = task;
1807         pm8001_ha_dev->id |= NCQ_READ_LOG_FLAG;
1808         pm8001_ha_dev->id |= NCQ_2ND_RLE_FLAG;
1809
1810         memset(&sata_cmd, 0, sizeof(sata_cmd));
1811         circularQ = &pm8001_ha->inbnd_q_tbl[0];
1812
1813         /* construct read log FIS */
1814         memset(&fis, 0, sizeof(struct host_to_dev_fis));
1815         fis.fis_type = 0x27;
1816         fis.flags = 0x80;
1817         fis.command = ATA_CMD_READ_LOG_EXT;
1818         fis.lbal = 0x10;
1819         fis.sector_count = 0x1;
1820
1821         sata_cmd.tag = cpu_to_le32(ccb_tag);
1822         sata_cmd.device_id = cpu_to_le32(pm8001_ha_dev->device_id);
1823         sata_cmd.ncqtag_atap_dir_m |= ((0x1 << 7) | (0x5 << 9));
1824         memcpy(&sata_cmd.sata_fis, &fis, sizeof(struct host_to_dev_fis));
1825
1826         res = pm8001_mpi_build_cmd(pm8001_ha, circularQ, opc, &sata_cmd, 0);
1827         if (res) {
1828                 sas_free_task(task);
1829                 pm8001_tag_free(pm8001_ha, ccb_tag);
1830                 kfree(dev);
1831         }
1832 }
1833
1834 /**
1835  * mpi_ssp_completion- process the event that FW response to the SSP request.
1836  * @pm8001_ha: our hba card information
1837  * @piomb: the message contents of this outbound message.
1838  *
1839  * When FW has completed a ssp request for example a IO request, after it has
1840  * filled the SG data with the data, it will trigger this event represent
1841  * that he has finished the job,please check the coresponding buffer.
1842  * So we will tell the caller who maybe waiting the result to tell upper layer
1843  * that the task has been finished.
1844  */
1845 static void
1846 mpi_ssp_completion(struct pm8001_hba_info *pm8001_ha , void *piomb)
1847 {
1848         struct sas_task *t;
1849         struct pm8001_ccb_info *ccb;
1850         unsigned long flags;
1851         u32 status;
1852         u32 param;
1853         u32 tag;
1854         struct ssp_completion_resp *psspPayload;
1855         struct task_status_struct *ts;
1856         struct ssp_response_iu *iu;
1857         struct pm8001_device *pm8001_dev;
1858         psspPayload = (struct ssp_completion_resp *)(piomb + 4);
1859         status = le32_to_cpu(psspPayload->status);
1860         tag = le32_to_cpu(psspPayload->tag);
1861         ccb = &pm8001_ha->ccb_info[tag];
1862         if ((status == IO_ABORTED) && ccb->open_retry) {
1863                 /* Being completed by another */
1864                 ccb->open_retry = 0;
1865                 return;
1866         }
1867         pm8001_dev = ccb->device;
1868         param = le32_to_cpu(psspPayload->param);
1869
1870         t = ccb->task;
1871
1872         if (status && status != IO_UNDERFLOW)
1873                 PM8001_FAIL_DBG(pm8001_ha,
1874                         pm8001_printk("sas IO status 0x%x\n", status));
1875         if (unlikely(!t || !t->lldd_task || !t->dev))
1876                 return;
1877         ts = &t->task_status;
1878         /* Print sas address of IO failed device */
1879         if ((status != IO_SUCCESS) && (status != IO_OVERFLOW) &&
1880                 (status != IO_UNDERFLOW))
1881                 PM8001_FAIL_DBG(pm8001_ha,
1882                         pm8001_printk("SAS Address of IO Failure Drive:"
1883                         "%016llx", SAS_ADDR(t->dev->sas_addr)));
1884
1885         switch (status) {
1886         case IO_SUCCESS:
1887                 PM8001_IO_DBG(pm8001_ha, pm8001_printk("IO_SUCCESS"
1888                         ",param = %d\n", param));
1889                 if (param == 0) {
1890                         ts->resp = SAS_TASK_COMPLETE;
1891                         ts->stat = SAM_STAT_GOOD;
1892                 } else {
1893                         ts->resp = SAS_TASK_COMPLETE;
1894                         ts->stat = SAS_PROTO_RESPONSE;
1895                         ts->residual = param;
1896                         iu = &psspPayload->ssp_resp_iu;
1897                         sas_ssp_task_response(pm8001_ha->dev, t, iu);
1898                 }
1899                 if (pm8001_dev)
1900                         pm8001_dev->running_req--;
1901                 break;
1902         case IO_ABORTED:
1903                 PM8001_IO_DBG(pm8001_ha,
1904                         pm8001_printk("IO_ABORTED IOMB Tag\n"));
1905                 ts->resp = SAS_TASK_COMPLETE;
1906                 ts->stat = SAS_ABORTED_TASK;
1907                 break;
1908         case IO_UNDERFLOW:
1909                 /* SSP Completion with error */
1910                 PM8001_IO_DBG(pm8001_ha, pm8001_printk("IO_UNDERFLOW"
1911                         ",param = %d\n", param));
1912                 ts->resp = SAS_TASK_COMPLETE;
1913                 ts->stat = SAS_DATA_UNDERRUN;
1914                 ts->residual = param;
1915                 if (pm8001_dev)
1916                         pm8001_dev->running_req--;
1917                 break;
1918         case IO_NO_DEVICE:
1919                 PM8001_IO_DBG(pm8001_ha,
1920                         pm8001_printk("IO_NO_DEVICE\n"));
1921                 ts->resp = SAS_TASK_UNDELIVERED;
1922                 ts->stat = SAS_PHY_DOWN;
1923                 break;
1924         case IO_XFER_ERROR_BREAK:
1925                 PM8001_IO_DBG(pm8001_ha,
1926                         pm8001_printk("IO_XFER_ERROR_BREAK\n"));
1927                 ts->resp = SAS_TASK_COMPLETE;
1928                 ts->stat = SAS_OPEN_REJECT;
1929                 /* Force the midlayer to retry */
1930                 ts->open_rej_reason = SAS_OREJ_RSVD_RETRY;
1931                 break;
1932         case IO_XFER_ERROR_PHY_NOT_READY:
1933                 PM8001_IO_DBG(pm8001_ha,
1934                         pm8001_printk("IO_XFER_ERROR_PHY_NOT_READY\n"));
1935                 ts->resp = SAS_TASK_COMPLETE;
1936                 ts->stat = SAS_OPEN_REJECT;
1937                 ts->open_rej_reason = SAS_OREJ_RSVD_RETRY;
1938                 break;
1939         case IO_OPEN_CNX_ERROR_PROTOCOL_NOT_SUPPORTED:
1940                 PM8001_IO_DBG(pm8001_ha,
1941                 pm8001_printk("IO_OPEN_CNX_ERROR_PROTOCOL_NOT_SUPPORTED\n"));
1942                 ts->resp = SAS_TASK_COMPLETE;
1943                 ts->stat = SAS_OPEN_REJECT;
1944                 ts->open_rej_reason = SAS_OREJ_EPROTO;
1945                 break;
1946         case IO_OPEN_CNX_ERROR_ZONE_VIOLATION:
1947                 PM8001_IO_DBG(pm8001_ha,
1948                         pm8001_printk("IO_OPEN_CNX_ERROR_ZONE_VIOLATION\n"));
1949                 ts->resp = SAS_TASK_COMPLETE;
1950                 ts->stat = SAS_OPEN_REJECT;
1951                 ts->open_rej_reason = SAS_OREJ_UNKNOWN;
1952                 break;
1953         case IO_OPEN_CNX_ERROR_BREAK:
1954                 PM8001_IO_DBG(pm8001_ha,
1955                         pm8001_printk("IO_OPEN_CNX_ERROR_BREAK\n"));
1956                 ts->resp = SAS_TASK_COMPLETE;
1957                 ts->stat = SAS_OPEN_REJECT;
1958                 ts->open_rej_reason = SAS_OREJ_RSVD_RETRY;
1959                 break;
1960         case IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS:
1961                 PM8001_IO_DBG(pm8001_ha,
1962                         pm8001_printk("IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS\n"));
1963                 ts->resp = SAS_TASK_COMPLETE;
1964                 ts->stat = SAS_OPEN_REJECT;
1965                 ts->open_rej_reason = SAS_OREJ_UNKNOWN;
1966                 if (!t->uldd_task)
1967                         pm8001_handle_event(pm8001_ha,
1968                                 pm8001_dev,
1969                                 IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS);
1970                 break;
1971         case IO_OPEN_CNX_ERROR_BAD_DESTINATION:
1972                 PM8001_IO_DBG(pm8001_ha,
1973                         pm8001_printk("IO_OPEN_CNX_ERROR_BAD_DESTINATION\n"));
1974                 ts->resp = SAS_TASK_COMPLETE;
1975                 ts->stat = SAS_OPEN_REJECT;
1976                 ts->open_rej_reason = SAS_OREJ_BAD_DEST;
1977                 break;
1978         case IO_OPEN_CNX_ERROR_CONNECTION_RATE_NOT_SUPPORTED:
1979                 PM8001_IO_DBG(pm8001_ha,
1980                         pm8001_printk("IO_OPEN_CNX_ERROR_CONNECTION_RATE_"
1981                         "NOT_SUPPORTED\n"));
1982                 ts->resp = SAS_TASK_COMPLETE;
1983                 ts->stat = SAS_OPEN_REJECT;
1984                 ts->open_rej_reason = SAS_OREJ_CONN_RATE;
1985                 break;
1986         case IO_OPEN_CNX_ERROR_WRONG_DESTINATION:
1987                 PM8001_IO_DBG(pm8001_ha,
1988                         pm8001_printk("IO_OPEN_CNX_ERROR_WRONG_DESTINATION\n"));
1989                 ts->resp = SAS_TASK_UNDELIVERED;
1990                 ts->stat = SAS_OPEN_REJECT;
1991                 ts->open_rej_reason = SAS_OREJ_WRONG_DEST;
1992                 break;
1993         case IO_XFER_ERROR_NAK_RECEIVED:
1994                 PM8001_IO_DBG(pm8001_ha,
1995                         pm8001_printk("IO_XFER_ERROR_NAK_RECEIVED\n"));
1996                 ts->resp = SAS_TASK_COMPLETE;
1997                 ts->stat = SAS_OPEN_REJECT;
1998                 ts->open_rej_reason = SAS_OREJ_RSVD_RETRY;
1999                 break;
2000         case IO_XFER_ERROR_ACK_NAK_TIMEOUT:
2001                 PM8001_IO_DBG(pm8001_ha,
2002                         pm8001_printk("IO_XFER_ERROR_ACK_NAK_TIMEOUT\n"));
2003                 ts->resp = SAS_TASK_COMPLETE;
2004                 ts->stat = SAS_NAK_R_ERR;
2005                 break;
2006         case IO_XFER_ERROR_DMA:
2007                 PM8001_IO_DBG(pm8001_ha,
2008                 pm8001_printk("IO_XFER_ERROR_DMA\n"));
2009                 ts->resp = SAS_TASK_COMPLETE;
2010                 ts->stat = SAS_OPEN_REJECT;
2011                 break;
2012         case IO_XFER_OPEN_RETRY_TIMEOUT:
2013                 PM8001_IO_DBG(pm8001_ha,
2014                         pm8001_printk("IO_XFER_OPEN_RETRY_TIMEOUT\n"));
2015                 ts->resp = SAS_TASK_COMPLETE;
2016                 ts->stat = SAS_OPEN_REJECT;
2017                 ts->open_rej_reason = SAS_OREJ_RSVD_RETRY;
2018                 break;
2019         case IO_XFER_ERROR_OFFSET_MISMATCH:
2020                 PM8001_IO_DBG(pm8001_ha,
2021                         pm8001_printk("IO_XFER_ERROR_OFFSET_MISMATCH\n"));
2022                 ts->resp = SAS_TASK_COMPLETE;
2023                 ts->stat = SAS_OPEN_REJECT;
2024                 break;
2025         case IO_PORT_IN_RESET:
2026                 PM8001_IO_DBG(pm8001_ha,
2027                         pm8001_printk("IO_PORT_IN_RESET\n"));
2028                 ts->resp = SAS_TASK_COMPLETE;
2029                 ts->stat = SAS_OPEN_REJECT;
2030                 break;
2031         case IO_DS_NON_OPERATIONAL:
2032                 PM8001_IO_DBG(pm8001_ha,
2033                         pm8001_printk("IO_DS_NON_OPERATIONAL\n"));
2034                 ts->resp = SAS_TASK_COMPLETE;
2035                 ts->stat = SAS_OPEN_REJECT;
2036                 if (!t->uldd_task)
2037                         pm8001_handle_event(pm8001_ha,
2038                                 pm8001_dev,
2039                                 IO_DS_NON_OPERATIONAL);
2040                 break;
2041         case IO_DS_IN_RECOVERY:
2042                 PM8001_IO_DBG(pm8001_ha,
2043                         pm8001_printk("IO_DS_IN_RECOVERY\n"));
2044                 ts->resp = SAS_TASK_COMPLETE;
2045                 ts->stat = SAS_OPEN_REJECT;
2046                 break;
2047         case IO_TM_TAG_NOT_FOUND:
2048                 PM8001_IO_DBG(pm8001_ha,
2049                         pm8001_printk("IO_TM_TAG_NOT_FOUND\n"));
2050                 ts->resp = SAS_TASK_COMPLETE;
2051                 ts->stat = SAS_OPEN_REJECT;
2052                 break;
2053         case IO_SSP_EXT_IU_ZERO_LEN_ERROR:
2054                 PM8001_IO_DBG(pm8001_ha,
2055                         pm8001_printk("IO_SSP_EXT_IU_ZERO_LEN_ERROR\n"));
2056                 ts->resp = SAS_TASK_COMPLETE;
2057                 ts->stat = SAS_OPEN_REJECT;
2058                 break;
2059         case IO_OPEN_CNX_ERROR_HW_RESOURCE_BUSY:
2060                 PM8001_IO_DBG(pm8001_ha,
2061                         pm8001_printk("IO_OPEN_CNX_ERROR_HW_RESOURCE_BUSY\n"));
2062                 ts->resp = SAS_TASK_COMPLETE;
2063                 ts->stat = SAS_OPEN_REJECT;
2064                 ts->open_rej_reason = SAS_OREJ_RSVD_RETRY;
2065                 break;
2066         default:
2067                 PM8001_IO_DBG(pm8001_ha,
2068                         pm8001_printk("Unknown status 0x%x\n", status));
2069                 /* not allowed case. Therefore, return failed status */
2070                 ts->resp = SAS_TASK_COMPLETE;
2071                 ts->stat = SAS_OPEN_REJECT;
2072                 break;
2073         }
2074         PM8001_IO_DBG(pm8001_ha,
2075                 pm8001_printk("scsi_status = %x\n ",
2076                 psspPayload->ssp_resp_iu.status));
2077         spin_lock_irqsave(&t->task_state_lock, flags);
2078         t->task_state_flags &= ~SAS_TASK_STATE_PENDING;
2079         t->task_state_flags &= ~SAS_TASK_AT_INITIATOR;
2080         t->task_state_flags |= SAS_TASK_STATE_DONE;
2081         if (unlikely((t->task_state_flags & SAS_TASK_STATE_ABORTED))) {
2082                 spin_unlock_irqrestore(&t->task_state_lock, flags);
2083                 PM8001_FAIL_DBG(pm8001_ha, pm8001_printk("task 0x%p done with"
2084                         " io_status 0x%x resp 0x%x "
2085                         "stat 0x%x but aborted by upper layer!\n",
2086                         t, status, ts->resp, ts->stat));
2087                 pm8001_ccb_task_free(pm8001_ha, t, ccb, tag);
2088         } else {
2089                 spin_unlock_irqrestore(&t->task_state_lock, flags);
2090                 pm8001_ccb_task_free(pm8001_ha, t, ccb, tag);
2091                 mb();/* in order to force CPU ordering */
2092                 t->task_done(t);
2093         }
2094 }
2095
2096 /*See the comments for mpi_ssp_completion */
2097 static void mpi_ssp_event(struct pm8001_hba_info *pm8001_ha , void *piomb)
2098 {
2099         struct sas_task *t;
2100         unsigned long flags;
2101         struct task_status_struct *ts;
2102         struct pm8001_ccb_info *ccb;
2103         struct pm8001_device *pm8001_dev;
2104         struct ssp_event_resp *psspPayload =
2105                 (struct ssp_event_resp *)(piomb + 4);
2106         u32 event = le32_to_cpu(psspPayload->event);
2107         u32 tag = le32_to_cpu(psspPayload->tag);
2108         u32 port_id = le32_to_cpu(psspPayload->port_id);
2109         u32 dev_id = le32_to_cpu(psspPayload->device_id);
2110
2111         ccb = &pm8001_ha->ccb_info[tag];
2112         t = ccb->task;
2113         pm8001_dev = ccb->device;
2114         if (event)
2115                 PM8001_FAIL_DBG(pm8001_ha,
2116                         pm8001_printk("sas IO status 0x%x\n", event));
2117         if (unlikely(!t || !t->lldd_task || !t->dev))
2118                 return;
2119         ts = &t->task_status;
2120         PM8001_IO_DBG(pm8001_ha,
2121                 pm8001_printk("port_id = %x,device_id = %x\n",
2122                 port_id, dev_id));
2123         switch (event) {
2124         case IO_OVERFLOW:
2125                 PM8001_IO_DBG(pm8001_ha, pm8001_printk("IO_UNDERFLOW\n");)
2126                 ts->resp = SAS_TASK_COMPLETE;
2127                 ts->stat = SAS_DATA_OVERRUN;
2128                 ts->residual = 0;
2129                 if (pm8001_dev)
2130                         pm8001_dev->running_req--;
2131                 break;
2132         case IO_XFER_ERROR_BREAK:
2133                 PM8001_IO_DBG(pm8001_ha,
2134                         pm8001_printk("IO_XFER_ERROR_BREAK\n"));
2135                 pm8001_handle_event(pm8001_ha, t, IO_XFER_ERROR_BREAK);
2136                 return;
2137         case IO_XFER_ERROR_PHY_NOT_READY:
2138                 PM8001_IO_DBG(pm8001_ha,
2139                         pm8001_printk("IO_XFER_ERROR_PHY_NOT_READY\n"));
2140                 ts->resp = SAS_TASK_COMPLETE;
2141                 ts->stat = SAS_OPEN_REJECT;
2142                 ts->open_rej_reason = SAS_OREJ_RSVD_RETRY;
2143                 break;
2144         case IO_OPEN_CNX_ERROR_PROTOCOL_NOT_SUPPORTED:
2145                 PM8001_IO_DBG(pm8001_ha,
2146                         pm8001_printk("IO_OPEN_CNX_ERROR_PROTOCOL_NOT"
2147                         "_SUPPORTED\n"));
2148                 ts->resp = SAS_TASK_COMPLETE;
2149                 ts->stat = SAS_OPEN_REJECT;
2150                 ts->open_rej_reason = SAS_OREJ_EPROTO;
2151                 break;
2152         case IO_OPEN_CNX_ERROR_ZONE_VIOLATION:
2153                 PM8001_IO_DBG(pm8001_ha,
2154                         pm8001_printk("IO_OPEN_CNX_ERROR_ZONE_VIOLATION\n"));
2155                 ts->resp = SAS_TASK_COMPLETE;
2156                 ts->stat = SAS_OPEN_REJECT;
2157                 ts->open_rej_reason = SAS_OREJ_UNKNOWN;
2158                 break;
2159         case IO_OPEN_CNX_ERROR_BREAK:
2160                 PM8001_IO_DBG(pm8001_ha,
2161                         pm8001_printk("IO_OPEN_CNX_ERROR_BREAK\n"));
2162                 ts->resp = SAS_TASK_COMPLETE;
2163                 ts->stat = SAS_OPEN_REJECT;
2164                 ts->open_rej_reason = SAS_OREJ_RSVD_RETRY;
2165                 break;
2166         case IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS:
2167                 PM8001_IO_DBG(pm8001_ha,
2168                         pm8001_printk("IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS\n"));
2169                 ts->resp = SAS_TASK_COMPLETE;
2170                 ts->stat = SAS_OPEN_REJECT;
2171                 ts->open_rej_reason = SAS_OREJ_UNKNOWN;
2172                 if (!t->uldd_task)
2173                         pm8001_handle_event(pm8001_ha,
2174                                 pm8001_dev,
2175                                 IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS);
2176                 break;
2177         case IO_OPEN_CNX_ERROR_BAD_DESTINATION:
2178                 PM8001_IO_DBG(pm8001_ha,
2179                         pm8001_printk("IO_OPEN_CNX_ERROR_BAD_DESTINATION\n"));
2180                 ts->resp = SAS_TASK_COMPLETE;
2181                 ts->stat = SAS_OPEN_REJECT;
2182                 ts->open_rej_reason = SAS_OREJ_BAD_DEST;
2183                 break;
2184         case IO_OPEN_CNX_ERROR_CONNECTION_RATE_NOT_SUPPORTED:
2185                 PM8001_IO_DBG(pm8001_ha,
2186                         pm8001_printk("IO_OPEN_CNX_ERROR_CONNECTION_RATE_"
2187                         "NOT_SUPPORTED\n"));
2188                 ts->resp = SAS_TASK_COMPLETE;
2189                 ts->stat = SAS_OPEN_REJECT;
2190                 ts->open_rej_reason = SAS_OREJ_CONN_RATE;
2191                 break;
2192         case IO_OPEN_CNX_ERROR_WRONG_DESTINATION:
2193                 PM8001_IO_DBG(pm8001_ha,
2194                        pm8001_printk("IO_OPEN_CNX_ERROR_WRONG_DESTINATION\n"));
2195                 ts->resp = SAS_TASK_COMPLETE;
2196                 ts->stat = SAS_OPEN_REJECT;
2197                 ts->open_rej_reason = SAS_OREJ_WRONG_DEST;
2198                 break;
2199         case IO_XFER_ERROR_NAK_RECEIVED:
2200                 PM8001_IO_DBG(pm8001_ha,
2201                         pm8001_printk("IO_XFER_ERROR_NAK_RECEIVED\n"));
2202                 ts->resp = SAS_TASK_COMPLETE;
2203                 ts->stat = SAS_OPEN_REJECT;
2204                 ts->open_rej_reason = SAS_OREJ_RSVD_RETRY;
2205                 break;
2206         case IO_XFER_ERROR_ACK_NAK_TIMEOUT:
2207                 PM8001_IO_DBG(pm8001_ha,
2208                         pm8001_printk("IO_XFER_ERROR_ACK_NAK_TIMEOUT\n"));
2209                 ts->resp = SAS_TASK_COMPLETE;
2210                 ts->stat = SAS_NAK_R_ERR;
2211                 break;
2212         case IO_XFER_OPEN_RETRY_TIMEOUT:
2213                 PM8001_IO_DBG(pm8001_ha,
2214                         pm8001_printk("IO_XFER_OPEN_RETRY_TIMEOUT\n"));
2215                 pm8001_handle_event(pm8001_ha, t, IO_XFER_OPEN_RETRY_TIMEOUT);
2216                 return;
2217         case IO_XFER_ERROR_UNEXPECTED_PHASE:
2218                 PM8001_IO_DBG(pm8001_ha,
2219                         pm8001_printk("IO_XFER_ERROR_UNEXPECTED_PHASE\n"));
2220                 ts->resp = SAS_TASK_COMPLETE;
2221                 ts->stat = SAS_DATA_OVERRUN;
2222                 break;
2223         case IO_XFER_ERROR_XFER_RDY_OVERRUN:
2224                 PM8001_IO_DBG(pm8001_ha,
2225                         pm8001_printk("IO_XFER_ERROR_XFER_RDY_OVERRUN\n"));
2226                 ts->resp = SAS_TASK_COMPLETE;
2227                 ts->stat = SAS_DATA_OVERRUN;
2228                 break;
2229         case IO_XFER_ERROR_XFER_RDY_NOT_EXPECTED:
2230                 PM8001_IO_DBG(pm8001_ha,
2231                        pm8001_printk("IO_XFER_ERROR_XFER_RDY_NOT_EXPECTED\n"));
2232                 ts->resp = SAS_TASK_COMPLETE;
2233                 ts->stat = SAS_DATA_OVERRUN;
2234                 break;
2235         case IO_XFER_ERROR_CMD_ISSUE_ACK_NAK_TIMEOUT:
2236                 PM8001_IO_DBG(pm8001_ha,
2237                 pm8001_printk("IO_XFER_ERROR_CMD_ISSUE_ACK_NAK_TIMEOUT\n"));
2238                 ts->resp = SAS_TASK_COMPLETE;
2239                 ts->stat = SAS_DATA_OVERRUN;
2240                 break;
2241         case IO_XFER_ERROR_OFFSET_MISMATCH:
2242                 PM8001_IO_DBG(pm8001_ha,
2243                         pm8001_printk("IO_XFER_ERROR_OFFSET_MISMATCH\n"));
2244                 ts->resp = SAS_TASK_COMPLETE;
2245                 ts->stat = SAS_DATA_OVERRUN;
2246                 break;
2247         case IO_XFER_ERROR_XFER_ZERO_DATA_LEN:
2248                 PM8001_IO_DBG(pm8001_ha,
2249                         pm8001_printk("IO_XFER_ERROR_XFER_ZERO_DATA_LEN\n"));
2250                 ts->resp = SAS_TASK_COMPLETE;
2251                 ts->stat = SAS_DATA_OVERRUN;
2252                 break;
2253         case IO_XFER_CMD_FRAME_ISSUED:
2254                 PM8001_IO_DBG(pm8001_ha,
2255                         pm8001_printk("  IO_XFER_CMD_FRAME_ISSUED\n"));
2256                 return;
2257         default:
2258                 PM8001_IO_DBG(pm8001_ha,
2259                         pm8001_printk("Unknown status 0x%x\n", event));
2260                 /* not allowed case. Therefore, return failed status */
2261                 ts->resp = SAS_TASK_COMPLETE;
2262                 ts->stat = SAS_DATA_OVERRUN;
2263                 break;
2264         }
2265         spin_lock_irqsave(&t->task_state_lock, flags);
2266         t->task_state_flags &= ~SAS_TASK_STATE_PENDING;
2267         t->task_state_flags &= ~SAS_TASK_AT_INITIATOR;
2268         t->task_state_flags |= SAS_TASK_STATE_DONE;
2269         if (unlikely((t->task_state_flags & SAS_TASK_STATE_ABORTED))) {
2270                 spin_unlock_irqrestore(&t->task_state_lock, flags);
2271                 PM8001_FAIL_DBG(pm8001_ha, pm8001_printk("task 0x%p done with"
2272                         " event 0x%x resp 0x%x "
2273                         "stat 0x%x but aborted by upper layer!\n",
2274                         t, event, ts->resp, ts->stat));
2275                 pm8001_ccb_task_free(pm8001_ha, t, ccb, tag);
2276         } else {
2277                 spin_unlock_irqrestore(&t->task_state_lock, flags);
2278                 pm8001_ccb_task_free(pm8001_ha, t, ccb, tag);
2279                 mb();/* in order to force CPU ordering */
2280                 t->task_done(t);
2281         }
2282 }
2283
2284 /*See the comments for mpi_ssp_completion */
2285 static void
2286 mpi_sata_completion(struct pm8001_hba_info *pm8001_ha, void *piomb)
2287 {
2288         struct sas_task *t;
2289         struct pm8001_ccb_info *ccb;
2290         u32 param;
2291         u32 status;
2292         u32 tag;
2293         int i, j;
2294         u8 sata_addr_low[4];
2295         u32 temp_sata_addr_low;
2296         u8 sata_addr_hi[4];
2297         u32 temp_sata_addr_hi;
2298         struct sata_completion_resp *psataPayload;
2299         struct task_status_struct *ts;
2300         struct ata_task_resp *resp ;
2301         u32 *sata_resp;
2302         struct pm8001_device *pm8001_dev;
2303         unsigned long flags;
2304
2305         psataPayload = (struct sata_completion_resp *)(piomb + 4);
2306         status = le32_to_cpu(psataPayload->status);
2307         tag = le32_to_cpu(psataPayload->tag);
2308
2309         if (!tag) {
2310                 PM8001_FAIL_DBG(pm8001_ha,
2311                         pm8001_printk("tag null\n"));
2312                 return;
2313         }
2314         ccb = &pm8001_ha->ccb_info[tag];
2315         param = le32_to_cpu(psataPayload->param);
2316         if (ccb) {
2317                 t = ccb->task;
2318                 pm8001_dev = ccb->device;
2319         } else {
2320                 PM8001_FAIL_DBG(pm8001_ha,
2321                         pm8001_printk("ccb null\n"));
2322                 return;
2323         }
2324
2325         if (t) {
2326                 if (t->dev && (t->dev->lldd_dev))
2327                         pm8001_dev = t->dev->lldd_dev;
2328         } else {
2329                 PM8001_FAIL_DBG(pm8001_ha,
2330                         pm8001_printk("task null\n"));
2331                 return;
2332         }
2333
2334         if ((pm8001_dev && !(pm8001_dev->id & NCQ_READ_LOG_FLAG))
2335                 && unlikely(!t || !t->lldd_task || !t->dev)) {
2336                 PM8001_FAIL_DBG(pm8001_ha,
2337                         pm8001_printk("task or dev null\n"));
2338                 return;
2339         }
2340
2341         ts = &t->task_status;
2342         if (!ts) {
2343                 PM8001_FAIL_DBG(pm8001_ha,
2344                         pm8001_printk("ts null\n"));
2345                 return;
2346         }
2347         /* Print sas address of IO failed device */
2348         if ((status != IO_SUCCESS) && (status != IO_OVERFLOW) &&
2349                 (status != IO_UNDERFLOW)) {
2350                 if (!((t->dev->parent) &&
2351                         (DEV_IS_EXPANDER(t->dev->parent->dev_type)))) {
2352                         for (i = 0 , j = 4; j <= 7 && i <= 3; i++ , j++)
2353                                 sata_addr_low[i] = pm8001_ha->sas_addr[j];
2354                         for (i = 0 , j = 0; j <= 3 && i <= 3; i++ , j++)
2355                                 sata_addr_hi[i] = pm8001_ha->sas_addr[j];
2356                         memcpy(&temp_sata_addr_low, sata_addr_low,
2357                                 sizeof(sata_addr_low));
2358                         memcpy(&temp_sata_addr_hi, sata_addr_hi,
2359                                 sizeof(sata_addr_hi));
2360                         temp_sata_addr_hi = (((temp_sata_addr_hi >> 24) & 0xff)
2361                                                 |((temp_sata_addr_hi << 8) &
2362                                                 0xff0000) |
2363                                                 ((temp_sata_addr_hi >> 8)
2364                                                 & 0xff00) |
2365                                                 ((temp_sata_addr_hi << 24) &
2366                                                 0xff000000));
2367                         temp_sata_addr_low = ((((temp_sata_addr_low >> 24)
2368                                                 & 0xff) |
2369                                                 ((temp_sata_addr_low << 8)
2370                                                 & 0xff0000) |
2371                                                 ((temp_sata_addr_low >> 8)
2372                                                 & 0xff00) |
2373                                                 ((temp_sata_addr_low << 24)
2374                                                 & 0xff000000)) +
2375                                                 pm8001_dev->attached_phy +
2376                                                 0x10);
2377                         PM8001_FAIL_DBG(pm8001_ha,
2378                                 pm8001_printk("SAS Address of IO Failure Drive:"
2379                                 "%08x%08x", temp_sata_addr_hi,
2380                                         temp_sata_addr_low));
2381                 } else {
2382                         PM8001_FAIL_DBG(pm8001_ha,
2383                                 pm8001_printk("SAS Address of IO Failure Drive:"
2384                                 "%016llx", SAS_ADDR(t->dev->sas_addr)));
2385                 }
2386         }
2387         switch (status) {
2388         case IO_SUCCESS:
2389                 PM8001_IO_DBG(pm8001_ha, pm8001_printk("IO_SUCCESS\n"));
2390                 if (param == 0) {
2391                         ts->resp = SAS_TASK_COMPLETE;
2392                         ts->stat = SAM_STAT_GOOD;
2393                         /* check if response is for SEND READ LOG */
2394                         if (pm8001_dev &&
2395                                 (pm8001_dev->id & NCQ_READ_LOG_FLAG)) {
2396                                 /* set new bit for abort_all */
2397                                 pm8001_dev->id |= NCQ_ABORT_ALL_FLAG;
2398                                 /* clear bit for read log */
2399                                 pm8001_dev->id = pm8001_dev->id & 0x7FFFFFFF;
2400                                 pm8001_send_abort_all(pm8001_ha, pm8001_dev);
2401                                 /* Free the tag */
2402                                 pm8001_tag_free(pm8001_ha, tag);
2403                                 sas_free_task(t);
2404                                 return;
2405                         }
2406                 } else {
2407                         u8 len;
2408                         ts->resp = SAS_TASK_COMPLETE;
2409                         ts->stat = SAS_PROTO_RESPONSE;
2410                         ts->residual = param;
2411                         PM8001_IO_DBG(pm8001_ha,
2412                                 pm8001_printk("SAS_PROTO_RESPONSE len = %d\n",
2413                                 param));
2414                         sata_resp = &psataPayload->sata_resp[0];
2415                         resp = (struct ata_task_resp *)ts->buf;
2416                         if (t->ata_task.dma_xfer == 0 &&
2417                         t->data_dir == PCI_DMA_FROMDEVICE) {
2418                                 len = sizeof(struct pio_setup_fis);
2419                                 PM8001_IO_DBG(pm8001_ha,
2420                                 pm8001_printk("PIO read len = %d\n", len));
2421                         } else if (t->ata_task.use_ncq) {
2422                                 len = sizeof(struct set_dev_bits_fis);
2423                                 PM8001_IO_DBG(pm8001_ha,
2424                                         pm8001_printk("FPDMA len = %d\n", len));
2425                         } else {
2426                                 len = sizeof(struct dev_to_host_fis);
2427                                 PM8001_IO_DBG(pm8001_ha,
2428                                 pm8001_printk("other len = %d\n", len));
2429                         }
2430                         if (SAS_STATUS_BUF_SIZE >= sizeof(*resp)) {
2431                                 resp->frame_len = len;
2432                                 memcpy(&resp->ending_fis[0], sata_resp, len);
2433                                 ts->buf_valid_size = sizeof(*resp);
2434                         } else
2435                                 PM8001_IO_DBG(pm8001_ha,
2436                                         pm8001_printk("response to large\n"));
2437                 }
2438                 if (pm8001_dev)
2439                         pm8001_dev->running_req--;
2440                 break;
2441         case IO_ABORTED:
2442                 PM8001_IO_DBG(pm8001_ha,
2443                         pm8001_printk("IO_ABORTED IOMB Tag\n"));
2444                 ts->resp = SAS_TASK_COMPLETE;
2445                 ts->stat = SAS_ABORTED_TASK;
2446                 if (pm8001_dev)
2447                         pm8001_dev->running_req--;
2448                 break;
2449                 /* following cases are to do cases */
2450         case IO_UNDERFLOW:
2451                 /* SATA Completion with error */
2452                 PM8001_IO_DBG(pm8001_ha,
2453                         pm8001_printk("IO_UNDERFLOW param = %d\n", param));
2454                 ts->resp = SAS_TASK_COMPLETE;
2455                 ts->stat = SAS_DATA_UNDERRUN;
2456                 ts->residual =  param;
2457                 if (pm8001_dev)
2458                         pm8001_dev->running_req--;
2459                 break;
2460         case IO_NO_DEVICE:
2461                 PM8001_IO_DBG(pm8001_ha,
2462                         pm8001_printk("IO_NO_DEVICE\n"));
2463                 ts->resp = SAS_TASK_UNDELIVERED;
2464                 ts->stat = SAS_PHY_DOWN;
2465                 break;
2466         case IO_XFER_ERROR_BREAK:
2467                 PM8001_IO_DBG(pm8001_ha,
2468                         pm8001_printk("IO_XFER_ERROR_BREAK\n"));
2469                 ts->resp = SAS_TASK_COMPLETE;
2470                 ts->stat = SAS_INTERRUPTED;
2471                 break;
2472         case IO_XFER_ERROR_PHY_NOT_READY:
2473                 PM8001_IO_DBG(pm8001_ha,
2474                         pm8001_printk("IO_XFER_ERROR_PHY_NOT_READY\n"));
2475                 ts->resp = SAS_TASK_COMPLETE;
2476                 ts->stat = SAS_OPEN_REJECT;
2477                 ts->open_rej_reason = SAS_OREJ_RSVD_RETRY;
2478                 break;
2479         case IO_OPEN_CNX_ERROR_PROTOCOL_NOT_SUPPORTED:
2480                 PM8001_IO_DBG(pm8001_ha,
2481                         pm8001_printk("IO_OPEN_CNX_ERROR_PROTOCOL_NOT"
2482                         "_SUPPORTED\n"));
2483                 ts->resp = SAS_TASK_COMPLETE;
2484                 ts->stat = SAS_OPEN_REJECT;
2485                 ts->open_rej_reason = SAS_OREJ_EPROTO;
2486                 break;
2487         case IO_OPEN_CNX_ERROR_ZONE_VIOLATION:
2488                 PM8001_IO_DBG(pm8001_ha,
2489                         pm8001_printk("IO_OPEN_CNX_ERROR_ZONE_VIOLATION\n"));
2490                 ts->resp = SAS_TASK_COMPLETE;
2491                 ts->stat = SAS_OPEN_REJECT;
2492                 ts->open_rej_reason = SAS_OREJ_UNKNOWN;
2493                 break;
2494         case IO_OPEN_CNX_ERROR_BREAK:
2495                 PM8001_IO_DBG(pm8001_ha,
2496                         pm8001_printk("IO_OPEN_CNX_ERROR_BREAK\n"));
2497                 ts->resp = SAS_TASK_COMPLETE;
2498                 ts->stat = SAS_OPEN_REJECT;
2499                 ts->open_rej_reason = SAS_OREJ_RSVD_CONT0;
2500                 break;
2501         case IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS:
2502                 PM8001_IO_DBG(pm8001_ha,
2503                         pm8001_printk("IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS\n"));
2504                 ts->resp = SAS_TASK_COMPLETE;
2505                 ts->stat = SAS_DEV_NO_RESPONSE;
2506                 if (!t->uldd_task) {
2507                         pm8001_handle_event(pm8001_ha,
2508                                 pm8001_dev,
2509                                 IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS);
2510                         ts->resp = SAS_TASK_UNDELIVERED;
2511                         ts->stat = SAS_QUEUE_FULL;
2512                         pm8001_ccb_task_free_done(pm8001_ha, t, ccb, tag);
2513                         return;
2514                 }
2515                 break;
2516         case IO_OPEN_CNX_ERROR_BAD_DESTINATION:
2517                 PM8001_IO_DBG(pm8001_ha,
2518                         pm8001_printk("IO_OPEN_CNX_ERROR_BAD_DESTINATION\n"));
2519                 ts->resp = SAS_TASK_UNDELIVERED;
2520                 ts->stat = SAS_OPEN_REJECT;
2521                 ts->open_rej_reason = SAS_OREJ_BAD_DEST;
2522                 if (!t->uldd_task) {
2523                         pm8001_handle_event(pm8001_ha,
2524                                 pm8001_dev,
2525                                 IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS);
2526                         ts->resp = SAS_TASK_UNDELIVERED;
2527                         ts->stat = SAS_QUEUE_FULL;
2528                         pm8001_ccb_task_free_done(pm8001_ha, t, ccb, tag);
2529                         return;
2530                 }
2531                 break;
2532         case IO_OPEN_CNX_ERROR_CONNECTION_RATE_NOT_SUPPORTED:
2533                 PM8001_IO_DBG(pm8001_ha,
2534                         pm8001_printk("IO_OPEN_CNX_ERROR_CONNECTION_RATE_"
2535                         "NOT_SUPPORTED\n"));
2536                 ts->resp = SAS_TASK_COMPLETE;
2537                 ts->stat = SAS_OPEN_REJECT;
2538                 ts->open_rej_reason = SAS_OREJ_CONN_RATE;
2539                 break;
2540         case IO_OPEN_CNX_ERROR_STP_RESOURCES_BUSY:
2541                 PM8001_IO_DBG(pm8001_ha,
2542                         pm8001_printk("IO_OPEN_CNX_ERROR_STP_RESOURCES"
2543                         "_BUSY\n"));
2544                 ts->resp = SAS_TASK_COMPLETE;
2545                 ts->stat = SAS_DEV_NO_RESPONSE;
2546                 if (!t->uldd_task) {
2547                         pm8001_handle_event(pm8001_ha,
2548                                 pm8001_dev,
2549                                 IO_OPEN_CNX_ERROR_STP_RESOURCES_BUSY);
2550                         ts->resp = SAS_TASK_UNDELIVERED;
2551                         ts->stat = SAS_QUEUE_FULL;
2552                         pm8001_ccb_task_free_done(pm8001_ha, t, ccb, tag);
2553                         return;
2554                 }
2555                 break;
2556         case IO_OPEN_CNX_ERROR_WRONG_DESTINATION:
2557                 PM8001_IO_DBG(pm8001_ha,
2558                        pm8001_printk("IO_OPEN_CNX_ERROR_WRONG_DESTINATION\n"));
2559                 ts->resp = SAS_TASK_COMPLETE;
2560                 ts->stat = SAS_OPEN_REJECT;
2561                 ts->open_rej_reason = SAS_OREJ_WRONG_DEST;
2562                 break;
2563         case IO_XFER_ERROR_NAK_RECEIVED:
2564                 PM8001_IO_DBG(pm8001_ha,
2565                         pm8001_printk("IO_XFER_ERROR_NAK_RECEIVED\n"));
2566                 ts->resp = SAS_TASK_COMPLETE;
2567                 ts->stat = SAS_NAK_R_ERR;
2568                 break;
2569         case IO_XFER_ERROR_ACK_NAK_TIMEOUT:
2570                 PM8001_IO_DBG(pm8001_ha,
2571                         pm8001_printk("IO_XFER_ERROR_ACK_NAK_TIMEOUT\n"));
2572                 ts->resp = SAS_TASK_COMPLETE;
2573                 ts->stat = SAS_NAK_R_ERR;
2574                 break;
2575         case IO_XFER_ERROR_DMA:
2576                 PM8001_IO_DBG(pm8001_ha,
2577                         pm8001_printk("IO_XFER_ERROR_DMA\n"));
2578                 ts->resp = SAS_TASK_COMPLETE;
2579                 ts->stat = SAS_ABORTED_TASK;
2580                 break;
2581         case IO_XFER_ERROR_SATA_LINK_TIMEOUT:
2582                 PM8001_IO_DBG(pm8001_ha,
2583                         pm8001_printk("IO_XFER_ERROR_SATA_LINK_TIMEOUT\n"));
2584                 ts->resp = SAS_TASK_UNDELIVERED;
2585                 ts->stat = SAS_DEV_NO_RESPONSE;
2586                 break;
2587         case IO_XFER_ERROR_REJECTED_NCQ_MODE:
2588                 PM8001_IO_DBG(pm8001_ha,
2589                         pm8001_printk("IO_XFER_ERROR_REJECTED_NCQ_MODE\n"));
2590                 ts->resp = SAS_TASK_COMPLETE;
2591                 ts->stat = SAS_DATA_UNDERRUN;
2592                 break;
2593         case IO_XFER_OPEN_RETRY_TIMEOUT:
2594                 PM8001_IO_DBG(pm8001_ha,
2595                         pm8001_printk("IO_XFER_OPEN_RETRY_TIMEOUT\n"));
2596                 ts->resp = SAS_TASK_COMPLETE;
2597                 ts->stat = SAS_OPEN_TO;
2598                 break;
2599         case IO_PORT_IN_RESET:
2600                 PM8001_IO_DBG(pm8001_ha,
2601                         pm8001_printk("IO_PORT_IN_RESET\n"));
2602                 ts->resp = SAS_TASK_COMPLETE;
2603                 ts->stat = SAS_DEV_NO_RESPONSE;
2604                 break;
2605         case IO_DS_NON_OPERATIONAL:
2606                 PM8001_IO_DBG(pm8001_ha,
2607                         pm8001_printk("IO_DS_NON_OPERATIONAL\n"));
2608                 ts->resp = SAS_TASK_COMPLETE;
2609                 ts->stat = SAS_DEV_NO_RESPONSE;
2610                 if (!t->uldd_task) {
2611                         pm8001_handle_event(pm8001_ha, pm8001_dev,
2612                                     IO_DS_NON_OPERATIONAL);
2613                         ts->resp = SAS_TASK_UNDELIVERED;
2614                         ts->stat = SAS_QUEUE_FULL;
2615                         pm8001_ccb_task_free_done(pm8001_ha, t, ccb, tag);
2616                         return;
2617                 }
2618                 break;
2619         case IO_DS_IN_RECOVERY:
2620                 PM8001_IO_DBG(pm8001_ha,
2621                         pm8001_printk("  IO_DS_IN_RECOVERY\n"));
2622                 ts->resp = SAS_TASK_COMPLETE;
2623                 ts->stat = SAS_DEV_NO_RESPONSE;
2624                 break;
2625         case IO_DS_IN_ERROR:
2626                 PM8001_IO_DBG(pm8001_ha,
2627                         pm8001_printk("IO_DS_IN_ERROR\n"));
2628                 ts->resp = SAS_TASK_COMPLETE;
2629                 ts->stat = SAS_DEV_NO_RESPONSE;
2630                 if (!t->uldd_task) {
2631                         pm8001_handle_event(pm8001_ha, pm8001_dev,
2632                                     IO_DS_IN_ERROR);
2633                         ts->resp = SAS_TASK_UNDELIVERED;
2634                         ts->stat = SAS_QUEUE_FULL;
2635                         pm8001_ccb_task_free_done(pm8001_ha, t, ccb, tag);
2636                         return;
2637                 }
2638                 break;
2639         case IO_OPEN_CNX_ERROR_HW_RESOURCE_BUSY:
2640                 PM8001_IO_DBG(pm8001_ha,
2641                         pm8001_printk("IO_OPEN_CNX_ERROR_HW_RESOURCE_BUSY\n"));
2642                 ts->resp = SAS_TASK_COMPLETE;
2643                 ts->stat = SAS_OPEN_REJECT;
2644                 ts->open_rej_reason = SAS_OREJ_RSVD_RETRY;
2645                 break;
2646         default:
2647                 PM8001_IO_DBG(pm8001_ha,
2648                         pm8001_printk("Unknown status 0x%x\n", status));
2649                 /* not allowed case. Therefore, return failed status */
2650                 ts->resp = SAS_TASK_COMPLETE;
2651                 ts->stat = SAS_DEV_NO_RESPONSE;
2652                 break;
2653         }
2654         spin_lock_irqsave(&t->task_state_lock, flags);
2655         t->task_state_flags &= ~SAS_TASK_STATE_PENDING;
2656         t->task_state_flags &= ~SAS_TASK_AT_INITIATOR;
2657         t->task_state_flags |= SAS_TASK_STATE_DONE;
2658         if (unlikely((t->task_state_flags & SAS_TASK_STATE_ABORTED))) {
2659                 spin_unlock_irqrestore(&t->task_state_lock, flags);
2660                 PM8001_FAIL_DBG(pm8001_ha,
2661                         pm8001_printk("task 0x%p done with io_status 0x%x"
2662                         " resp 0x%x stat 0x%x but aborted by upper layer!\n",
2663                         t, status, ts->resp, ts->stat));
2664                 pm8001_ccb_task_free(pm8001_ha, t, ccb, tag);
2665         } else {
2666                 spin_unlock_irqrestore(&t->task_state_lock, flags);
2667                 pm8001_ccb_task_free_done(pm8001_ha, t, ccb, tag);
2668         }
2669 }
2670
2671 /*See the comments for mpi_ssp_completion */
2672 static void mpi_sata_event(struct pm8001_hba_info *pm8001_ha , void *piomb)
2673 {
2674         struct sas_task *t;
2675         struct task_status_struct *ts;
2676         struct pm8001_ccb_info *ccb;
2677         struct pm8001_device *pm8001_dev;
2678         struct sata_event_resp *psataPayload =
2679                 (struct sata_event_resp *)(piomb + 4);
2680         u32 event = le32_to_cpu(psataPayload->event);
2681         u32 tag = le32_to_cpu(psataPayload->tag);
2682         u32 port_id = le32_to_cpu(psataPayload->port_id);
2683         u32 dev_id = le32_to_cpu(psataPayload->device_id);
2684         unsigned long flags;
2685
2686         ccb = &pm8001_ha->ccb_info[tag];
2687
2688         if (ccb) {
2689                 t = ccb->task;
2690                 pm8001_dev = ccb->device;
2691         } else {
2692                 PM8001_FAIL_DBG(pm8001_ha,
2693                         pm8001_printk("No CCB !!!. returning\n"));
2694         }
2695         if (event)
2696                 PM8001_FAIL_DBG(pm8001_ha,
2697                         pm8001_printk("SATA EVENT 0x%x\n", event));
2698
2699         /* Check if this is NCQ error */
2700         if (event == IO_XFER_ERROR_ABORTED_NCQ_MODE) {
2701                 /* find device using device id */
2702                 pm8001_dev = pm8001_find_dev(pm8001_ha, dev_id);
2703                 /* send read log extension */
2704                 if (pm8001_dev)
2705                         pm8001_send_read_log(pm8001_ha, pm8001_dev);
2706                 return;
2707         }
2708
2709         ccb = &pm8001_ha->ccb_info[tag];
2710         t = ccb->task;
2711         pm8001_dev = ccb->device;
2712         if (event)
2713                 PM8001_FAIL_DBG(pm8001_ha,
2714                         pm8001_printk("sata IO status 0x%x\n", event));
2715         if (unlikely(!t || !t->lldd_task || !t->dev))
2716                 return;
2717         ts = &t->task_status;
2718         PM8001_IO_DBG(pm8001_ha, pm8001_printk(
2719                 "port_id:0x%x, device_id:0x%x, tag:0x%x, event:0x%x\n",
2720                 port_id, dev_id, tag, event));
2721         switch (event) {
2722         case IO_OVERFLOW:
2723                 PM8001_IO_DBG(pm8001_ha, pm8001_printk("IO_UNDERFLOW\n"));
2724                 ts->resp = SAS_TASK_COMPLETE;
2725                 ts->stat = SAS_DATA_OVERRUN;
2726                 ts->residual = 0;
2727                 if (pm8001_dev)
2728                         pm8001_dev->running_req--;
2729                 break;
2730         case IO_XFER_ERROR_BREAK:
2731                 PM8001_IO_DBG(pm8001_ha,
2732                         pm8001_printk("IO_XFER_ERROR_BREAK\n"));
2733                 ts->resp = SAS_TASK_COMPLETE;
2734                 ts->stat = SAS_INTERRUPTED;
2735                 break;
2736         case IO_XFER_ERROR_PHY_NOT_READY:
2737                 PM8001_IO_DBG(pm8001_ha,
2738                         pm8001_printk("IO_XFER_ERROR_PHY_NOT_READY\n"));
2739                 ts->resp = SAS_TASK_COMPLETE;
2740                 ts->stat = SAS_OPEN_REJECT;
2741                 ts->open_rej_reason = SAS_OREJ_RSVD_RETRY;
2742                 break;
2743         case IO_OPEN_CNX_ERROR_PROTOCOL_NOT_SUPPORTED:
2744                 PM8001_IO_DBG(pm8001_ha,
2745                         pm8001_printk("IO_OPEN_CNX_ERROR_PROTOCOL_NOT"
2746                         "_SUPPORTED\n"));
2747                 ts->resp = SAS_TASK_COMPLETE;
2748                 ts->stat = SAS_OPEN_REJECT;
2749                 ts->open_rej_reason = SAS_OREJ_EPROTO;
2750                 break;
2751         case IO_OPEN_CNX_ERROR_ZONE_VIOLATION:
2752                 PM8001_IO_DBG(pm8001_ha,
2753                         pm8001_printk("IO_OPEN_CNX_ERROR_ZONE_VIOLATION\n"));
2754                 ts->resp = SAS_TASK_COMPLETE;
2755                 ts->stat = SAS_OPEN_REJECT;
2756                 ts->open_rej_reason = SAS_OREJ_UNKNOWN;
2757                 break;
2758         case IO_OPEN_CNX_ERROR_BREAK:
2759                 PM8001_IO_DBG(pm8001_ha,
2760                         pm8001_printk("IO_OPEN_CNX_ERROR_BREAK\n"));
2761                 ts->resp = SAS_TASK_COMPLETE;
2762                 ts->stat = SAS_OPEN_REJECT;
2763                 ts->open_rej_reason = SAS_OREJ_RSVD_CONT0;
2764                 break;
2765         case IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS:
2766                 PM8001_IO_DBG(pm8001_ha,
2767                         pm8001_printk("IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS\n"));
2768                 ts->resp = SAS_TASK_UNDELIVERED;
2769                 ts->stat = SAS_DEV_NO_RESPONSE;
2770                 if (!t->uldd_task) {
2771                         pm8001_handle_event(pm8001_ha,
2772                                 pm8001_dev,
2773                                 IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS);
2774                         ts->resp = SAS_TASK_COMPLETE;
2775                         ts->stat = SAS_QUEUE_FULL;
2776                         pm8001_ccb_task_free_done(pm8001_ha, t, ccb, tag);
2777                         return;
2778                 }
2779                 break;
2780         case IO_OPEN_CNX_ERROR_BAD_DESTINATION:
2781                 PM8001_IO_DBG(pm8001_ha,
2782                         pm8001_printk("IO_OPEN_CNX_ERROR_BAD_DESTINATION\n"));
2783                 ts->resp = SAS_TASK_UNDELIVERED;
2784                 ts->stat = SAS_OPEN_REJECT;
2785                 ts->open_rej_reason = SAS_OREJ_BAD_DEST;
2786                 break;
2787         case IO_OPEN_CNX_ERROR_CONNECTION_RATE_NOT_SUPPORTED:
2788                 PM8001_IO_DBG(pm8001_ha,
2789                         pm8001_printk("IO_OPEN_CNX_ERROR_CONNECTION_RATE_"
2790                         "NOT_SUPPORTED\n"));
2791                 ts->resp = SAS_TASK_COMPLETE;
2792                 ts->stat = SAS_OPEN_REJECT;
2793                 ts->open_rej_reason = SAS_OREJ_CONN_RATE;
2794                 break;
2795         case IO_OPEN_CNX_ERROR_WRONG_DESTINATION:
2796                 PM8001_IO_DBG(pm8001_ha,
2797                        pm8001_printk("IO_OPEN_CNX_ERROR_WRONG_DESTINATION\n"));
2798                 ts->resp = SAS_TASK_COMPLETE;
2799                 ts->stat = SAS_OPEN_REJECT;
2800                 ts->open_rej_reason = SAS_OREJ_WRONG_DEST;
2801                 break;
2802         case IO_XFER_ERROR_NAK_RECEIVED:
2803                 PM8001_IO_DBG(pm8001_ha,
2804                         pm8001_printk("IO_XFER_ERROR_NAK_RECEIVED\n"));
2805                 ts->resp = SAS_TASK_COMPLETE;
2806                 ts->stat = SAS_NAK_R_ERR;
2807                 break;
2808         case IO_XFER_ERROR_PEER_ABORTED:
2809                 PM8001_IO_DBG(pm8001_ha,
2810                         pm8001_printk("IO_XFER_ERROR_PEER_ABORTED\n"));
2811                 ts->resp = SAS_TASK_COMPLETE;
2812                 ts->stat = SAS_NAK_R_ERR;
2813                 break;
2814         case IO_XFER_ERROR_REJECTED_NCQ_MODE:
2815                 PM8001_IO_DBG(pm8001_ha,
2816                         pm8001_printk("IO_XFER_ERROR_REJECTED_NCQ_MODE\n"));
2817                 ts->resp = SAS_TASK_COMPLETE;
2818                 ts->stat = SAS_DATA_UNDERRUN;
2819                 break;
2820         case IO_XFER_OPEN_RETRY_TIMEOUT:
2821                 PM8001_IO_DBG(pm8001_ha,
2822                         pm8001_printk("IO_XFER_OPEN_RETRY_TIMEOUT\n"));
2823                 ts->resp = SAS_TASK_COMPLETE;
2824                 ts->stat = SAS_OPEN_TO;
2825                 break;
2826         case IO_XFER_ERROR_UNEXPECTED_PHASE:
2827                 PM8001_IO_DBG(pm8001_ha,
2828                         pm8001_printk("IO_XFER_ERROR_UNEXPECTED_PHASE\n"));
2829                 ts->resp = SAS_TASK_COMPLETE;
2830                 ts->stat = SAS_OPEN_TO;
2831                 break;
2832         case IO_XFER_ERROR_XFER_RDY_OVERRUN:
2833                 PM8001_IO_DBG(pm8001_ha,
2834                         pm8001_printk("IO_XFER_ERROR_XFER_RDY_OVERRUN\n"));
2835                 ts->resp = SAS_TASK_COMPLETE;
2836                 ts->stat = SAS_OPEN_TO;
2837                 break;
2838         case IO_XFER_ERROR_XFER_RDY_NOT_EXPECTED:
2839                 PM8001_IO_DBG(pm8001_ha,
2840                        pm8001_printk("IO_XFER_ERROR_XFER_RDY_NOT_EXPECTED\n"));
2841                 ts->resp = SAS_TASK_COMPLETE;
2842                 ts->stat = SAS_OPEN_TO;
2843                 break;
2844         case IO_XFER_ERROR_OFFSET_MISMATCH:
2845                 PM8001_IO_DBG(pm8001_ha,
2846                         pm8001_printk("IO_XFER_ERROR_OFFSET_MISMATCH\n"));
2847                 ts->resp = SAS_TASK_COMPLETE;
2848                 ts->stat = SAS_OPEN_TO;
2849                 break;
2850         case IO_XFER_ERROR_XFER_ZERO_DATA_LEN:
2851                 PM8001_IO_DBG(pm8001_ha,
2852                         pm8001_printk("IO_XFER_ERROR_XFER_ZERO_DATA_LEN\n"));
2853                 ts->resp = SAS_TASK_COMPLETE;
2854                 ts->stat = SAS_OPEN_TO;
2855                 break;
2856         case IO_XFER_CMD_FRAME_ISSUED:
2857                 PM8001_IO_DBG(pm8001_ha,
2858                         pm8001_printk("IO_XFER_CMD_FRAME_ISSUED\n"));
2859                 break;
2860         case IO_XFER_PIO_SETUP_ERROR:
2861                 PM8001_IO_DBG(pm8001_ha,
2862                         pm8001_printk("IO_XFER_PIO_SETUP_ERROR\n"));
2863                 ts->resp = SAS_TASK_COMPLETE;
2864                 ts->stat = SAS_OPEN_TO;
2865                 break;
2866         default:
2867                 PM8001_IO_DBG(pm8001_ha,
2868                         pm8001_printk("Unknown status 0x%x\n", event));
2869                 /* not allowed case. Therefore, return failed status */
2870                 ts->resp = SAS_TASK_COMPLETE;
2871                 ts->stat = SAS_OPEN_TO;
2872                 break;
2873         }
2874         spin_lock_irqsave(&t->task_state_lock, flags);
2875         t->task_state_flags &= ~SAS_TASK_STATE_PENDING;
2876         t->task_state_flags &= ~SAS_TASK_AT_INITIATOR;
2877         t->task_state_flags |= SAS_TASK_STATE_DONE;
2878         if (unlikely((t->task_state_flags & SAS_TASK_STATE_ABORTED))) {
2879                 spin_unlock_irqrestore(&t->task_state_lock, flags);
2880                 PM8001_FAIL_DBG(pm8001_ha,
2881                         pm8001_printk("task 0x%p done with io_status 0x%x"
2882                         " resp 0x%x stat 0x%x but aborted by upper layer!\n",
2883                         t, event, ts->resp, ts->stat));
2884                 pm8001_ccb_task_free(pm8001_ha, t, ccb, tag);
2885         } else {
2886                 spin_unlock_irqrestore(&t->task_state_lock, flags);
2887                 pm8001_ccb_task_free_done(pm8001_ha, t, ccb, tag);
2888         }
2889 }
2890
2891 /*See the comments for mpi_ssp_completion */
2892 static void
2893 mpi_smp_completion(struct pm8001_hba_info *pm8001_ha, void *piomb)
2894 {
2895         u32 param;
2896         struct sas_task *t;
2897         struct pm8001_ccb_info *ccb;
2898         unsigned long flags;
2899         u32 status;
2900         u32 tag;
2901         struct smp_completion_resp *psmpPayload;
2902         struct task_status_struct *ts;
2903         struct pm8001_device *pm8001_dev;
2904
2905         psmpPayload = (struct smp_completion_resp *)(piomb + 4);
2906         status = le32_to_cpu(psmpPayload->status);
2907         tag = le32_to_cpu(psmpPayload->tag);
2908
2909         ccb = &pm8001_ha->ccb_info[tag];
2910         param = le32_to_cpu(psmpPayload->param);
2911         t = ccb->task;
2912         ts = &t->task_status;
2913         pm8001_dev = ccb->device;
2914         if (status)
2915                 PM8001_FAIL_DBG(pm8001_ha,
2916                         pm8001_printk("smp IO status 0x%x\n", status));
2917         if (unlikely(!t || !t->lldd_task || !t->dev))
2918                 return;
2919
2920         switch (status) {
2921         case IO_SUCCESS:
2922                 PM8001_IO_DBG(pm8001_ha, pm8001_printk("IO_SUCCESS\n"));
2923                 ts->resp = SAS_TASK_COMPLETE;
2924                 ts->stat = SAM_STAT_GOOD;
2925         if (pm8001_dev)
2926                         pm8001_dev->running_req--;
2927                 break;
2928         case IO_ABORTED:
2929                 PM8001_IO_DBG(pm8001_ha,
2930                         pm8001_printk("IO_ABORTED IOMB\n"));
2931                 ts->resp = SAS_TASK_COMPLETE;
2932                 ts->stat = SAS_ABORTED_TASK;
2933                 if (pm8001_dev)
2934                         pm8001_dev->running_req--;
2935                 break;
2936         case IO_OVERFLOW:
2937                 PM8001_IO_DBG(pm8001_ha, pm8001_printk("IO_UNDERFLOW\n"));
2938                 ts->resp = SAS_TASK_COMPLETE;
2939                 ts->stat = SAS_DATA_OVERRUN;
2940                 ts->residual = 0;
2941                 if (pm8001_dev)
2942                         pm8001_dev->running_req--;
2943                 break;
2944         case IO_NO_DEVICE:
2945                 PM8001_IO_DBG(pm8001_ha, pm8001_printk("IO_NO_DEVICE\n"));
2946                 ts->resp = SAS_TASK_COMPLETE;
2947                 ts->stat = SAS_PHY_DOWN;
2948                 break;
2949         case IO_ERROR_HW_TIMEOUT:
2950                 PM8001_IO_DBG(pm8001_ha,
2951                         pm8001_printk("IO_ERROR_HW_TIMEOUT\n"));
2952                 ts->resp = SAS_TASK_COMPLETE;
2953                 ts->stat = SAM_STAT_BUSY;
2954                 break;
2955         case IO_XFER_ERROR_BREAK:
2956                 PM8001_IO_DBG(pm8001_ha,
2957                         pm8001_printk("IO_XFER_ERROR_BREAK\n"));
2958                 ts->resp = SAS_TASK_COMPLETE;
2959                 ts->stat = SAM_STAT_BUSY;
2960                 break;
2961         case IO_XFER_ERROR_PHY_NOT_READY:
2962                 PM8001_IO_DBG(pm8001_ha,
2963                         pm8001_printk("IO_XFER_ERROR_PHY_NOT_READY\n"));
2964                 ts->resp = SAS_TASK_COMPLETE;
2965                 ts->stat = SAM_STAT_BUSY;
2966                 break;
2967         case IO_OPEN_CNX_ERROR_PROTOCOL_NOT_SUPPORTED:
2968                 PM8001_IO_DBG(pm8001_ha,
2969                 pm8001_printk("IO_OPEN_CNX_ERROR_PROTOCOL_NOT_SUPPORTED\n"));
2970                 ts->resp = SAS_TASK_COMPLETE;
2971                 ts->stat = SAS_OPEN_REJECT;
2972                 ts->open_rej_reason = SAS_OREJ_UNKNOWN;
2973                 break;
2974         case IO_OPEN_CNX_ERROR_ZONE_VIOLATION:
2975                 PM8001_IO_DBG(pm8001_ha,
2976                         pm8001_printk("IO_OPEN_CNX_ERROR_ZONE_VIOLATION\n"));
2977                 ts->resp = SAS_TASK_COMPLETE;
2978                 ts->stat = SAS_OPEN_REJECT;
2979                 ts->open_rej_reason = SAS_OREJ_UNKNOWN;
2980                 break;
2981         case IO_OPEN_CNX_ERROR_BREAK:
2982                 PM8001_IO_DBG(pm8001_ha,
2983                         pm8001_printk("IO_OPEN_CNX_ERROR_BREAK\n"));
2984                 ts->resp = SAS_TASK_COMPLETE;
2985                 ts->stat = SAS_OPEN_REJECT;
2986                 ts->open_rej_reason = SAS_OREJ_RSVD_CONT0;
2987                 break;
2988         case IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS:
2989                 PM8001_IO_DBG(pm8001_ha,
2990                         pm8001_printk("IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS\n"));
2991                 ts->resp = SAS_TASK_COMPLETE;
2992                 ts->stat = SAS_OPEN_REJECT;
2993                 ts->open_rej_reason = SAS_OREJ_UNKNOWN;
2994                 pm8001_handle_event(pm8001_ha,
2995                                 pm8001_dev,
2996                                 IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS);
2997                 break;
2998         case IO_OPEN_CNX_ERROR_BAD_DESTINATION:
2999                 PM8001_IO_DBG(pm8001_ha,
3000                         pm8001_printk("IO_OPEN_CNX_ERROR_BAD_DESTINATION\n"));
3001                 ts->resp = SAS_TASK_COMPLETE;
3002                 ts->stat = SAS_OPEN_REJECT;
3003                 ts->open_rej_reason = SAS_OREJ_BAD_DEST;
3004                 break;
3005         case IO_OPEN_CNX_ERROR_CONNECTION_RATE_NOT_SUPPORTED:
3006                 PM8001_IO_DBG(pm8001_ha,
3007                         pm8001_printk("IO_OPEN_CNX_ERROR_CONNECTION_RATE_"
3008                         "NOT_SUPPORTED\n"));
3009                 ts->resp = SAS_TASK_COMPLETE;
3010                 ts->stat = SAS_OPEN_REJECT;
3011                 ts->open_rej_reason = SAS_OREJ_CONN_RATE;
3012                 break;
3013         case IO_OPEN_CNX_ERROR_WRONG_DESTINATION:
3014                 PM8001_IO_DBG(pm8001_ha,
3015                        pm8001_printk("IO_OPEN_CNX_ERROR_WRONG_DESTINATION\n"));
3016                 ts->resp = SAS_TASK_COMPLETE;
3017                 ts->stat = SAS_OPEN_REJECT;
3018                 ts->open_rej_reason = SAS_OREJ_WRONG_DEST;
3019                 break;
3020         case IO_XFER_ERROR_RX_FRAME:
3021                 PM8001_IO_DBG(pm8001_ha,
3022                         pm8001_printk("IO_XFER_ERROR_RX_FRAME\n"));
3023                 ts->resp = SAS_TASK_COMPLETE;
3024                 ts->stat = SAS_DEV_NO_RESPONSE;
3025                 break;
3026         case IO_XFER_OPEN_RETRY_TIMEOUT:
3027                 PM8001_IO_DBG(pm8001_ha,
3028                         pm8001_printk("IO_XFER_OPEN_RETRY_TIMEOUT\n"));
3029                 ts->resp = SAS_TASK_COMPLETE;
3030                 ts->stat = SAS_OPEN_REJECT;
3031                 ts->open_rej_reason = SAS_OREJ_RSVD_RETRY;
3032                 break;
3033         case IO_ERROR_INTERNAL_SMP_RESOURCE:
3034                 PM8001_IO_DBG(pm8001_ha,
3035                         pm8001_printk("IO_ERROR_INTERNAL_SMP_RESOURCE\n"));
3036                 ts->resp = SAS_TASK_COMPLETE;
3037                 ts->stat = SAS_QUEUE_FULL;
3038                 break;
3039         case IO_PORT_IN_RESET:
3040                 PM8001_IO_DBG(pm8001_ha,
3041                         pm8001_printk("IO_PORT_IN_RESET\n"));
3042                 ts->resp = SAS_TASK_COMPLETE;
3043                 ts->stat = SAS_OPEN_REJECT;
3044                 ts->open_rej_reason = SAS_OREJ_RSVD_RETRY;
3045                 break;
3046         case IO_DS_NON_OPERATIONAL:
3047                 PM8001_IO_DBG(pm8001_ha,
3048                         pm8001_printk("IO_DS_NON_OPERATIONAL\n"));
3049                 ts->resp = SAS_TASK_COMPLETE;
3050                 ts->stat = SAS_DEV_NO_RESPONSE;
3051                 break;
3052         case IO_DS_IN_RECOVERY:
3053                 PM8001_IO_DBG(pm8001_ha,
3054                         pm8001_printk("IO_DS_IN_RECOVERY\n"));
3055                 ts->resp = SAS_TASK_COMPLETE;
3056                 ts->stat = SAS_OPEN_REJECT;
3057                 ts->open_rej_reason = SAS_OREJ_RSVD_RETRY;
3058                 break;
3059         case IO_OPEN_CNX_ERROR_HW_RESOURCE_BUSY:
3060                 PM8001_IO_DBG(pm8001_ha,
3061                         pm8001_printk("IO_OPEN_CNX_ERROR_HW_RESOURCE_BUSY\n"));
3062                 ts->resp = SAS_TASK_COMPLETE;
3063                 ts->stat = SAS_OPEN_REJECT;
3064                 ts->open_rej_reason = SAS_OREJ_RSVD_RETRY;
3065                 break;
3066         default:
3067                 PM8001_IO_DBG(pm8001_ha,
3068                         pm8001_printk("Unknown status 0x%x\n", status));
3069                 ts->resp = SAS_TASK_COMPLETE;
3070                 ts->stat = SAS_DEV_NO_RESPONSE;
3071                 /* not allowed case. Therefore, return failed status */
3072                 break;
3073         }
3074         spin_lock_irqsave(&t->task_state_lock, flags);
3075         t->task_state_flags &= ~SAS_TASK_STATE_PENDING;
3076         t->task_state_flags &= ~SAS_TASK_AT_INITIATOR;
3077         t->task_state_flags |= SAS_TASK_STATE_DONE;
3078         if (unlikely((t->task_state_flags & SAS_TASK_STATE_ABORTED))) {
3079                 spin_unlock_irqrestore(&t->task_state_lock, flags);
3080                 PM8001_FAIL_DBG(pm8001_ha, pm8001_printk("task 0x%p done with"
3081                         " io_status 0x%x resp 0x%x "
3082                         "stat 0x%x but aborted by upper layer!\n",
3083                         t, status, ts->resp, ts->stat));
3084                 pm8001_ccb_task_free(pm8001_ha, t, ccb, tag);
3085         } else {
3086                 spin_unlock_irqrestore(&t->task_state_lock, flags);
3087                 pm8001_ccb_task_free(pm8001_ha, t, ccb, tag);
3088                 mb();/* in order to force CPU ordering */
3089                 t->task_done(t);
3090         }
3091 }
3092
3093 void pm8001_mpi_set_dev_state_resp(struct pm8001_hba_info *pm8001_ha,
3094                 void *piomb)
3095 {
3096         struct set_dev_state_resp *pPayload =
3097                 (struct set_dev_state_resp *)(piomb + 4);
3098         u32 tag = le32_to_cpu(pPayload->tag);
3099         struct pm8001_ccb_info *ccb = &pm8001_ha->ccb_info[tag];
3100         struct pm8001_device *pm8001_dev = ccb->device;
3101         u32 status = le32_to_cpu(pPayload->status);
3102         u32 device_id = le32_to_cpu(pPayload->device_id);
3103         u8 pds = le32_to_cpu(pPayload->pds_nds) & PDS_BITS;
3104         u8 nds = le32_to_cpu(pPayload->pds_nds) & NDS_BITS;
3105         PM8001_MSG_DBG(pm8001_ha, pm8001_printk("Set device id = 0x%x state "
3106                 "from 0x%x to 0x%x status = 0x%x!\n",
3107                 device_id, pds, nds, status));
3108         complete(pm8001_dev->setds_completion);
3109         ccb->task = NULL;
3110         ccb->ccb_tag = 0xFFFFFFFF;
3111         pm8001_tag_free(pm8001_ha, tag);
3112 }
3113
3114 void pm8001_mpi_set_nvmd_resp(struct pm8001_hba_info *pm8001_ha, void *piomb)
3115 {
3116         struct get_nvm_data_resp *pPayload =
3117                 (struct get_nvm_data_resp *)(piomb + 4);
3118         u32 tag = le32_to_cpu(pPayload->tag);
3119         struct pm8001_ccb_info *ccb = &pm8001_ha->ccb_info[tag];
3120         u32 dlen_status = le32_to_cpu(pPayload->dlen_status);
3121         complete(pm8001_ha->nvmd_completion);
3122         PM8001_MSG_DBG(pm8001_ha, pm8001_printk("Set nvm data complete!\n"));
3123         if ((dlen_status & NVMD_STAT) != 0) {
3124                 PM8001_FAIL_DBG(pm8001_ha,
3125                         pm8001_printk("Set nvm data error!\n"));
3126                 return;
3127         }
3128         ccb->task = NULL;
3129         ccb->ccb_tag = 0xFFFFFFFF;
3130         pm8001_tag_free(pm8001_ha, tag);
3131 }
3132
3133 void
3134 pm8001_mpi_get_nvmd_resp(struct pm8001_hba_info *pm8001_ha, void *piomb)
3135 {
3136         struct fw_control_ex    *fw_control_context;
3137         struct get_nvm_data_resp *pPayload =
3138                 (struct get_nvm_data_resp *)(piomb + 4);
3139         u32 tag = le32_to_cpu(pPayload->tag);
3140         struct pm8001_ccb_info *ccb = &pm8001_ha->ccb_info[tag];
3141         u32 dlen_status = le32_to_cpu(pPayload->dlen_status);
3142         u32 ir_tds_bn_dps_das_nvm =
3143                 le32_to_cpu(pPayload->ir_tda_bn_dps_das_nvm);
3144         void *virt_addr = pm8001_ha->memoryMap.region[NVMD].virt_ptr;
3145         fw_control_context = ccb->fw_control_context;
3146
3147         PM8001_MSG_DBG(pm8001_ha, pm8001_printk("Get nvm data complete!\n"));
3148         if ((dlen_status & NVMD_STAT) != 0) {
3149                 PM8001_FAIL_DBG(pm8001_ha,
3150                         pm8001_printk("Get nvm data error!\n"));
3151                 complete(pm8001_ha->nvmd_completion);
3152                 return;
3153         }
3154
3155         if (ir_tds_bn_dps_das_nvm & IPMode) {
3156                 /* indirect mode - IR bit set */
3157                 PM8001_MSG_DBG(pm8001_ha,
3158                         pm8001_printk("Get NVMD success, IR=1\n"));
3159                 if ((ir_tds_bn_dps_das_nvm & NVMD_TYPE) == TWI_DEVICE) {
3160                         if (ir_tds_bn_dps_das_nvm == 0x80a80200) {
3161                                 memcpy(pm8001_ha->sas_addr,
3162                                       ((u8 *)virt_addr + 4),
3163                                        SAS_ADDR_SIZE);
3164                                 PM8001_MSG_DBG(pm8001_ha,
3165                                         pm8001_printk("Get SAS address"
3166                                         " from VPD successfully!\n"));
3167                         }
3168                 } else if (((ir_tds_bn_dps_das_nvm & NVMD_TYPE) == C_SEEPROM)
3169                         || ((ir_tds_bn_dps_das_nvm & NVMD_TYPE) == VPD_FLASH) ||
3170                         ((ir_tds_bn_dps_das_nvm & NVMD_TYPE) == EXPAN_ROM)) {
3171                                 ;
3172                 } else if (((ir_tds_bn_dps_das_nvm & NVMD_TYPE) == AAP1_RDUMP)
3173                         || ((ir_tds_bn_dps_das_nvm & NVMD_TYPE) == IOP_RDUMP)) {
3174                         ;
3175                 } else {
3176                         /* Should not be happened*/
3177                         PM8001_MSG_DBG(pm8001_ha,
3178                                 pm8001_printk("(IR=1)Wrong Device type 0x%x\n",
3179                                 ir_tds_bn_dps_das_nvm));
3180                 }
3181         } else /* direct mode */{
3182                 PM8001_MSG_DBG(pm8001_ha,
3183                         pm8001_printk("Get NVMD success, IR=0, dataLen=%d\n",
3184                         (dlen_status & NVMD_LEN) >> 24));
3185         }
3186         /* Though fw_control_context is freed below, usrAddr still needs
3187          * to be updated as this holds the response to the request function
3188          */
3189         memcpy(fw_control_context->usrAddr,
3190                 pm8001_ha->memoryMap.region[NVMD].virt_ptr,
3191                 fw_control_context->len);
3192         kfree(ccb->fw_control_context);
3193         ccb->task = NULL;
3194         ccb->ccb_tag = 0xFFFFFFFF;
3195         pm8001_tag_free(pm8001_ha, tag);
3196         complete(pm8001_ha->nvmd_completion);
3197 }
3198
3199 int pm8001_mpi_local_phy_ctl(struct pm8001_hba_info *pm8001_ha, void *piomb)
3200 {
3201         struct local_phy_ctl_resp *pPayload =
3202                 (struct local_phy_ctl_resp *)(piomb + 4);
3203         u32 status = le32_to_cpu(pPayload->status);
3204         u32 phy_id = le32_to_cpu(pPayload->phyop_phyid) & ID_BITS;
3205         u32 phy_op = le32_to_cpu(pPayload->phyop_phyid) & OP_BITS;
3206         if (status != 0) {
3207                 PM8001_MSG_DBG(pm8001_ha,
3208                         pm8001_printk("%x phy execute %x phy op failed!\n",
3209                         phy_id, phy_op));
3210         } else
3211                 PM8001_MSG_DBG(pm8001_ha,
3212                         pm8001_printk("%x phy execute %x phy op success!\n",
3213                         phy_id, phy_op));
3214         return 0;
3215 }
3216
3217 /**
3218  * pm8001_bytes_dmaed - one of the interface function communication with libsas
3219  * @pm8001_ha: our hba card information
3220  * @i: which phy that received the event.
3221  *
3222  * when HBA driver received the identify done event or initiate FIS received
3223  * event(for SATA), it will invoke this function to notify the sas layer that
3224  * the sas toplogy has formed, please discover the the whole sas domain,
3225  * while receive a broadcast(change) primitive just tell the sas
3226  * layer to discover the changed domain rather than the whole domain.
3227  */
3228 void pm8001_bytes_dmaed(struct pm8001_hba_info *pm8001_ha, int i)
3229 {
3230         struct pm8001_phy *phy = &pm8001_ha->phy[i];
3231         struct asd_sas_phy *sas_phy = &phy->sas_phy;
3232         struct sas_ha_struct *sas_ha;
3233         if (!phy->phy_attached)
3234                 return;
3235
3236         sas_ha = pm8001_ha->sas;
3237         if (sas_phy->phy) {
3238                 struct sas_phy *sphy = sas_phy->phy;
3239                 sphy->negotiated_linkrate = sas_phy->linkrate;
3240                 sphy->minimum_linkrate = phy->minimum_linkrate;
3241                 sphy->minimum_linkrate_hw = SAS_LINK_RATE_1_5_GBPS;
3242                 sphy->maximum_linkrate = phy->maximum_linkrate;
3243                 sphy->maximum_linkrate_hw = phy->maximum_linkrate;
3244         }
3245
3246         if (phy->phy_type & PORT_TYPE_SAS) {
3247                 struct sas_identify_frame *id;
3248                 id = (struct sas_identify_frame *)phy->frame_rcvd;
3249                 id->dev_type = phy->identify.device_type;
3250                 id->initiator_bits = SAS_PROTOCOL_ALL;
3251                 id->target_bits = phy->identify.target_port_protocols;
3252         } else if (phy->phy_type & PORT_TYPE_SATA) {
3253                 /*Nothing*/
3254         }
3255         PM8001_MSG_DBG(pm8001_ha, pm8001_printk("phy %d byte dmaded.\n", i));
3256
3257         sas_phy->frame_rcvd_size = phy->frame_rcvd_size;
3258         pm8001_ha->sas->notify_port_event(sas_phy, PORTE_BYTES_DMAED);
3259 }
3260
3261 /* Get the link rate speed  */
3262 void pm8001_get_lrate_mode(struct pm8001_phy *phy, u8 link_rate)
3263 {
3264         struct sas_phy *sas_phy = phy->sas_phy.phy;
3265
3266         switch (link_rate) {
3267         case PHY_SPEED_120:
3268                 phy->sas_phy.linkrate = SAS_LINK_RATE_12_0_GBPS;
3269                 phy->sas_phy.phy->negotiated_linkrate = SAS_LINK_RATE_12_0_GBPS;
3270                 break;
3271         case PHY_SPEED_60:
3272                 phy->sas_phy.linkrate = SAS_LINK_RATE_6_0_GBPS;
3273                 phy->sas_phy.phy->negotiated_linkrate = SAS_LINK_RATE_6_0_GBPS;
3274                 break;
3275         case PHY_SPEED_30:
3276                 phy->sas_phy.linkrate = SAS_LINK_RATE_3_0_GBPS;
3277                 phy->sas_phy.phy->negotiated_linkrate = SAS_LINK_RATE_3_0_GBPS;
3278                 break;
3279         case PHY_SPEED_15:
3280                 phy->sas_phy.linkrate = SAS_LINK_RATE_1_5_GBPS;
3281                 phy->sas_phy.phy->negotiated_linkrate = SAS_LINK_RATE_1_5_GBPS;
3282                 break;
3283         }
3284         sas_phy->negotiated_linkrate = phy->sas_phy.linkrate;
3285         sas_phy->maximum_linkrate_hw = SAS_LINK_RATE_6_0_GBPS;
3286         sas_phy->minimum_linkrate_hw = SAS_LINK_RATE_1_5_GBPS;
3287         sas_phy->maximum_linkrate = SAS_LINK_RATE_6_0_GBPS;
3288         sas_phy->minimum_linkrate = SAS_LINK_RATE_1_5_GBPS;
3289 }
3290
3291 /**
3292  * asd_get_attached_sas_addr -- extract/generate attached SAS address
3293  * @phy: pointer to asd_phy
3294  * @sas_addr: pointer to buffer where the SAS address is to be written
3295  *
3296  * This function extracts the SAS address from an IDENTIFY frame
3297  * received.  If OOB is SATA, then a SAS address is generated from the
3298  * HA tables.
3299  *
3300  * LOCKING: the frame_rcvd_lock needs to be held since this parses the frame
3301  * buffer.
3302  */
3303 void pm8001_get_attached_sas_addr(struct pm8001_phy *phy,
3304         u8 *sas_addr)
3305 {
3306         if (phy->sas_phy.frame_rcvd[0] == 0x34
3307                 && phy->sas_phy.oob_mode == SATA_OOB_MODE) {
3308                 struct pm8001_hba_info *pm8001_ha = phy->sas_phy.ha->lldd_ha;
3309                 /* FIS device-to-host */
3310                 u64 addr = be64_to_cpu(*(__be64 *)pm8001_ha->sas_addr);
3311                 addr += phy->sas_phy.id;
3312                 *(__be64 *)sas_addr = cpu_to_be64(addr);
3313         } else {
3314                 struct sas_identify_frame *idframe =
3315                         (void *) phy->sas_phy.frame_rcvd;
3316                 memcpy(sas_addr, idframe->sas_addr, SAS_ADDR_SIZE);
3317         }
3318 }
3319
3320 /**
3321  * pm8001_hw_event_ack_req- For PM8001,some events need to acknowage to FW.
3322  * @pm8001_ha: our hba card information
3323  * @Qnum: the outbound queue message number.
3324  * @SEA: source of event to ack
3325  * @port_id: port id.
3326  * @phyId: phy id.
3327  * @param0: parameter 0.
3328  * @param1: parameter 1.
3329  */
3330 static void pm8001_hw_event_ack_req(struct pm8001_hba_info *pm8001_ha,
3331         u32 Qnum, u32 SEA, u32 port_id, u32 phyId, u32 param0, u32 param1)
3332 {
3333         struct hw_event_ack_req  payload;
3334         u32 opc = OPC_INB_SAS_HW_EVENT_ACK;
3335
3336         struct inbound_queue_table *circularQ;
3337
3338         memset((u8 *)&payload, 0, sizeof(payload));
3339         circularQ = &pm8001_ha->inbnd_q_tbl[Qnum];
3340         payload.tag = cpu_to_le32(1);
3341         payload.sea_phyid_portid = cpu_to_le32(((SEA & 0xFFFF) << 8) |
3342                 ((phyId & 0x0F) << 4) | (port_id & 0x0F));
3343         payload.param0 = cpu_to_le32(param0);
3344         payload.param1 = cpu_to_le32(param1);
3345         pm8001_mpi_build_cmd(pm8001_ha, circularQ, opc, &payload, 0);
3346 }
3347
3348 static int pm8001_chip_phy_ctl_req(struct pm8001_hba_info *pm8001_ha,
3349         u32 phyId, u32 phy_op);
3350
3351 /**
3352  * hw_event_sas_phy_up -FW tells me a SAS phy up event.
3353  * @pm8001_ha: our hba card information
3354  * @piomb: IO message buffer
3355  */
3356 static void
3357 hw_event_sas_phy_up(struct pm8001_hba_info *pm8001_ha, void *piomb)
3358 {
3359         struct hw_event_resp *pPayload =
3360                 (struct hw_event_resp *)(piomb + 4);
3361         u32 lr_evt_status_phyid_portid =
3362                 le32_to_cpu(pPayload->lr_evt_status_phyid_portid);
3363         u8 link_rate =
3364                 (u8)((lr_evt_status_phyid_portid & 0xF0000000) >> 28);
3365         u8 port_id = (u8)(lr_evt_status_phyid_portid & 0x0000000F);
3366         u8 phy_id =
3367                 (u8)((lr_evt_status_phyid_portid & 0x000000F0) >> 4);
3368         u32 npip_portstate = le32_to_cpu(pPayload->npip_portstate);
3369         u8 portstate = (u8)(npip_portstate & 0x0000000F);
3370         struct pm8001_port *port = &pm8001_ha->port[port_id];
3371         struct sas_ha_struct *sas_ha = pm8001_ha->sas;
3372         struct pm8001_phy *phy = &pm8001_ha->phy[phy_id];
3373         unsigned long flags;
3374         u8 deviceType = pPayload->sas_identify.dev_type;
3375         port->port_state =  portstate;
3376         phy->phy_state = PHY_STATE_LINK_UP_SPC;
3377         PM8001_MSG_DBG(pm8001_ha,
3378                 pm8001_printk("HW_EVENT_SAS_PHY_UP port id = %d, phy id = %d\n",
3379                 port_id, phy_id));
3380
3381         switch (deviceType) {
3382         case SAS_PHY_UNUSED:
3383                 PM8001_MSG_DBG(pm8001_ha,
3384                         pm8001_printk("device type no device.\n"));
3385                 break;
3386         case SAS_END_DEVICE:
3387                 PM8001_MSG_DBG(pm8001_ha, pm8001_printk("end device.\n"));
3388                 pm8001_chip_phy_ctl_req(pm8001_ha, phy_id,
3389                         PHY_NOTIFY_ENABLE_SPINUP);
3390                 port->port_attached = 1;
3391                 pm8001_get_lrate_mode(phy, link_rate);
3392                 break;
3393         case SAS_EDGE_EXPANDER_DEVICE:
3394                 PM8001_MSG_DBG(pm8001_ha,
3395                         pm8001_printk("expander device.\n"));
3396                 port->port_attached = 1;
3397                 pm8001_get_lrate_mode(phy, link_rate);
3398                 break;
3399         case SAS_FANOUT_EXPANDER_DEVICE:
3400                 PM8001_MSG_DBG(pm8001_ha,
3401                         pm8001_printk("fanout expander device.\n"));
3402                 port->port_attached = 1;
3403                 pm8001_get_lrate_mode(phy, link_rate);
3404                 break;
3405         default:
3406                 PM8001_MSG_DBG(pm8001_ha,
3407                         pm8001_printk("unknown device type(%x)\n", deviceType));
3408                 break;
3409         }
3410         phy->phy_type |= PORT_TYPE_SAS;
3411         phy->identify.device_type = deviceType;
3412         phy->phy_attached = 1;
3413         if (phy->identify.device_type == SAS_END_DEVICE)
3414                 phy->identify.target_port_protocols = SAS_PROTOCOL_SSP;
3415         else if (phy->identify.device_type != SAS_PHY_UNUSED)
3416                 phy->identify.target_port_protocols = SAS_PROTOCOL_SMP;
3417         phy->sas_phy.oob_mode = SAS_OOB_MODE;
3418         sas_ha->notify_phy_event(&phy->sas_phy, PHYE_OOB_DONE);
3419         spin_lock_irqsave(&phy->sas_phy.frame_rcvd_lock, flags);
3420         memcpy(phy->frame_rcvd, &pPayload->sas_identify,
3421                 sizeof(struct sas_identify_frame)-4);
3422         phy->frame_rcvd_size = sizeof(struct sas_identify_frame) - 4;
3423         pm8001_get_attached_sas_addr(phy, phy->sas_phy.attached_sas_addr);
3424         spin_unlock_irqrestore(&phy->sas_phy.frame_rcvd_lock, flags);
3425         if (pm8001_ha->flags == PM8001F_RUN_TIME)
3426                 mdelay(200);/*delay a moment to wait disk to spinup*/
3427         pm8001_bytes_dmaed(pm8001_ha, phy_id);
3428 }
3429
3430 /**
3431  * hw_event_sata_phy_up -FW tells me a SATA phy up event.
3432  * @pm8001_ha: our hba card information
3433  * @piomb: IO message buffer
3434  */
3435 static void
3436 hw_event_sata_phy_up(struct pm8001_hba_info *pm8001_ha, void *piomb)
3437 {
3438         struct hw_event_resp *pPayload =
3439                 (struct hw_event_resp *)(piomb + 4);
3440         u32 lr_evt_status_phyid_portid =
3441                 le32_to_cpu(pPayload->lr_evt_status_phyid_portid);
3442         u8 link_rate =
3443                 (u8)((lr_evt_status_phyid_portid & 0xF0000000) >> 28);
3444         u8 port_id = (u8)(lr_evt_status_phyid_portid & 0x0000000F);
3445         u8 phy_id =
3446                 (u8)((lr_evt_status_phyid_portid & 0x000000F0) >> 4);
3447         u32 npip_portstate = le32_to_cpu(pPayload->npip_portstate);
3448         u8 portstate = (u8)(npip_portstate & 0x0000000F);
3449         struct pm8001_port *port = &pm8001_ha->port[port_id];
3450         struct sas_ha_struct *sas_ha = pm8001_ha->sas;
3451         struct pm8001_phy *phy = &pm8001_ha->phy[phy_id];
3452         unsigned long flags;
3453         PM8001_MSG_DBG(pm8001_ha,
3454                 pm8001_printk("HW_EVENT_SATA_PHY_UP port id = %d,"
3455                 " phy id = %d\n", port_id, phy_id));
3456         port->port_state =  portstate;
3457         phy->phy_state = PHY_STATE_LINK_UP_SPC;
3458         port->port_attached = 1;
3459         pm8001_get_lrate_mode(phy, link_rate);
3460         phy->phy_type |= PORT_TYPE_SATA;
3461         phy->phy_attached = 1;
3462         phy->sas_phy.oob_mode = SATA_OOB_MODE;
3463         sas_ha->notify_phy_event(&phy->sas_phy, PHYE_OOB_DONE);
3464         spin_lock_irqsave(&phy->sas_phy.frame_rcvd_lock, flags);
3465         memcpy(phy->frame_rcvd, ((u8 *)&pPayload->sata_fis - 4),
3466                 sizeof(struct dev_to_host_fis));
3467         phy->frame_rcvd_size = sizeof(struct dev_to_host_fis);
3468         phy->identify.target_port_protocols = SAS_PROTOCOL_SATA;
3469         phy->identify.device_type = SAS_SATA_DEV;
3470         pm8001_get_attached_sas_addr(phy, phy->sas_phy.attached_sas_addr);
3471         spin_unlock_irqrestore(&phy->sas_phy.frame_rcvd_lock, flags);
3472         pm8001_bytes_dmaed(pm8001_ha, phy_id);
3473 }
3474
3475 /**
3476  * hw_event_phy_down -we should notify the libsas the phy is down.
3477  * @pm8001_ha: our hba card information
3478  * @piomb: IO message buffer
3479  */
3480 static void
3481 hw_event_phy_down(struct pm8001_hba_info *pm8001_ha, void *piomb)
3482 {
3483         struct hw_event_resp *pPayload =
3484                 (struct hw_event_resp *)(piomb + 4);
3485         u32 lr_evt_status_phyid_portid =
3486                 le32_to_cpu(pPayload->lr_evt_status_phyid_portid);
3487         u8 port_id = (u8)(lr_evt_status_phyid_portid & 0x0000000F);
3488         u8 phy_id =
3489                 (u8)((lr_evt_status_phyid_portid & 0x000000F0) >> 4);
3490         u32 npip_portstate = le32_to_cpu(pPayload->npip_portstate);
3491         u8 portstate = (u8)(npip_portstate & 0x0000000F);
3492         struct pm8001_port *port = &pm8001_ha->port[port_id];
3493         struct pm8001_phy *phy = &pm8001_ha->phy[phy_id];
3494         port->port_state =  portstate;
3495         phy->phy_type = 0;
3496         phy->identify.device_type = 0;
3497         phy->phy_attached = 0;
3498         memset(&phy->dev_sas_addr, 0, SAS_ADDR_SIZE);
3499         switch (portstate) {
3500         case PORT_VALID:
3501                 break;
3502         case PORT_INVALID:
3503                 PM8001_MSG_DBG(pm8001_ha,
3504                         pm8001_printk(" PortInvalid portID %d\n", port_id));
3505                 PM8001_MSG_DBG(pm8001_ha,
3506                         pm8001_printk(" Last phy Down and port invalid\n"));
3507                 port->port_attached = 0;
3508                 pm8001_hw_event_ack_req(pm8001_ha, 0, HW_EVENT_PHY_DOWN,
3509                         port_id, phy_id, 0, 0);
3510                 break;
3511         case PORT_IN_RESET:
3512                 PM8001_MSG_DBG(pm8001_ha,
3513                         pm8001_printk(" Port In Reset portID %d\n", port_id));
3514                 break;
3515         case PORT_NOT_ESTABLISHED:
3516                 PM8001_MSG_DBG(pm8001_ha,
3517                         pm8001_printk(" phy Down and PORT_NOT_ESTABLISHED\n"));
3518                 port->port_attached = 0;
3519                 break;
3520         case PORT_LOSTCOMM:
3521                 PM8001_MSG_DBG(pm8001_ha,
3522                         pm8001_printk(" phy Down and PORT_LOSTCOMM\n"));
3523                 PM8001_MSG_DBG(pm8001_ha,
3524                         pm8001_printk(" Last phy Down and port invalid\n"));
3525                 port->port_attached = 0;
3526                 pm8001_hw_event_ack_req(pm8001_ha, 0, HW_EVENT_PHY_DOWN,
3527                         port_id, phy_id, 0, 0);
3528                 break;
3529         default:
3530                 port->port_attached = 0;
3531                 PM8001_MSG_DBG(pm8001_ha,
3532                         pm8001_printk(" phy Down and(default) = %x\n",
3533                         portstate));
3534                 break;
3535
3536         }
3537 }
3538
3539 /**
3540  * pm8001_mpi_reg_resp -process register device ID response.
3541  * @pm8001_ha: our hba card information
3542  * @piomb: IO message buffer
3543  *
3544  * when sas layer find a device it will notify LLDD, then the driver register
3545  * the domain device to FW, this event is the return device ID which the FW
3546  * has assigned, from now,inter-communication with FW is no longer using the
3547  * SAS address, use device ID which FW assigned.
3548  */
3549 int pm8001_mpi_reg_resp(struct pm8001_hba_info *pm8001_ha, void *piomb)
3550 {
3551         u32 status;
3552         u32 device_id;
3553         u32 htag;
3554         struct pm8001_ccb_info *ccb;
3555         struct pm8001_device *pm8001_dev;
3556         struct dev_reg_resp *registerRespPayload =
3557                 (struct dev_reg_resp *)(piomb + 4);
3558
3559         htag = le32_to_cpu(registerRespPayload->tag);
3560         ccb = &pm8001_ha->ccb_info[htag];
3561         pm8001_dev = ccb->device;
3562         status = le32_to_cpu(registerRespPayload->status);
3563         device_id = le32_to_cpu(registerRespPayload->device_id);
3564         PM8001_MSG_DBG(pm8001_ha,
3565                 pm8001_printk(" register device is status = %d\n", status));
3566         switch (status) {
3567         case DEVREG_SUCCESS:
3568                 PM8001_MSG_DBG(pm8001_ha, pm8001_printk("DEVREG_SUCCESS\n"));
3569                 pm8001_dev->device_id = device_id;
3570                 break;
3571         case DEVREG_FAILURE_OUT_OF_RESOURCE:
3572                 PM8001_MSG_DBG(pm8001_ha,
3573                         pm8001_printk("DEVREG_FAILURE_OUT_OF_RESOURCE\n"));
3574                 break;
3575         case DEVREG_FAILURE_DEVICE_ALREADY_REGISTERED:
3576                 PM8001_MSG_DBG(pm8001_ha,
3577                    pm8001_printk("DEVREG_FAILURE_DEVICE_ALREADY_REGISTERED\n"));
3578                 break;
3579         case DEVREG_FAILURE_INVALID_PHY_ID:
3580                 PM8001_MSG_DBG(pm8001_ha,
3581                         pm8001_printk("DEVREG_FAILURE_INVALID_PHY_ID\n"));
3582                 break;
3583         case DEVREG_FAILURE_PHY_ID_ALREADY_REGISTERED:
3584                 PM8001_MSG_DBG(pm8001_ha,
3585                    pm8001_printk("DEVREG_FAILURE_PHY_ID_ALREADY_REGISTERED\n"));
3586                 break;
3587         case DEVREG_FAILURE_PORT_ID_OUT_OF_RANGE:
3588                 PM8001_MSG_DBG(pm8001_ha,
3589                         pm8001_printk("DEVREG_FAILURE_PORT_ID_OUT_OF_RANGE\n"));
3590                 break;
3591         case DEVREG_FAILURE_PORT_NOT_VALID_STATE:
3592                 PM8001_MSG_DBG(pm8001_ha,
3593                         pm8001_printk("DEVREG_FAILURE_PORT_NOT_VALID_STATE\n"));
3594                 break;
3595         case DEVREG_FAILURE_DEVICE_TYPE_NOT_VALID:
3596                 PM8001_MSG_DBG(pm8001_ha,
3597                        pm8001_printk("DEVREG_FAILURE_DEVICE_TYPE_NOT_VALID\n"));
3598                 break;
3599         default:
3600                 PM8001_MSG_DBG(pm8001_ha,
3601                  pm8001_printk("DEVREG_FAILURE_DEVICE_TYPE_NOT_UNSORPORTED\n"));
3602                 break;
3603         }
3604         complete(pm8001_dev->dcompletion);
3605         ccb->task = NULL;
3606         ccb->ccb_tag = 0xFFFFFFFF;
3607         pm8001_tag_free(pm8001_ha, htag);
3608         return 0;
3609 }
3610
3611 int pm8001_mpi_dereg_resp(struct pm8001_hba_info *pm8001_ha, void *piomb)
3612 {
3613         u32 status;
3614         u32 device_id;
3615         struct dev_reg_resp *registerRespPayload =
3616                 (struct dev_reg_resp *)(piomb + 4);
3617
3618         status = le32_to_cpu(registerRespPayload->status);
3619         device_id = le32_to_cpu(registerRespPayload->device_id);
3620         if (status != 0)
3621                 PM8001_MSG_DBG(pm8001_ha,
3622                         pm8001_printk(" deregister device failed ,status = %x"
3623                         ", device_id = %x\n", status, device_id));
3624         return 0;
3625 }
3626
3627 /**
3628  * fw_flash_update_resp - Response from FW for flash update command.
3629  * @pm8001_ha: our hba card information
3630  * @piomb: IO message buffer
3631  */
3632 int pm8001_mpi_fw_flash_update_resp(struct pm8001_hba_info *pm8001_ha,
3633                 void *piomb)
3634 {
3635         u32 status;
3636         struct fw_flash_Update_resp *ppayload =
3637                 (struct fw_flash_Update_resp *)(piomb + 4);
3638         u32 tag = le32_to_cpu(ppayload->tag);
3639         struct pm8001_ccb_info *ccb = &pm8001_ha->ccb_info[tag];
3640         status = le32_to_cpu(ppayload->status);
3641         switch (status) {
3642         case FLASH_UPDATE_COMPLETE_PENDING_REBOOT:
3643                 PM8001_MSG_DBG(pm8001_ha,
3644                 pm8001_printk(": FLASH_UPDATE_COMPLETE_PENDING_REBOOT\n"));
3645                 break;
3646         case FLASH_UPDATE_IN_PROGRESS:
3647                 PM8001_MSG_DBG(pm8001_ha,
3648                         pm8001_printk(": FLASH_UPDATE_IN_PROGRESS\n"));
3649                 break;
3650         case FLASH_UPDATE_HDR_ERR:
3651                 PM8001_MSG_DBG(pm8001_ha,
3652                         pm8001_printk(": FLASH_UPDATE_HDR_ERR\n"));
3653                 break;
3654         case FLASH_UPDATE_OFFSET_ERR:
3655                 PM8001_MSG_DBG(pm8001_ha,
3656                         pm8001_printk(": FLASH_UPDATE_OFFSET_ERR\n"));
3657                 break;
3658         case FLASH_UPDATE_CRC_ERR:
3659                 PM8001_MSG_DBG(pm8001_ha,
3660                         pm8001_printk(": FLASH_UPDATE_CRC_ERR\n"));
3661                 break;
3662         case FLASH_UPDATE_LENGTH_ERR:
3663                 PM8001_MSG_DBG(pm8001_ha,
3664                         pm8001_printk(": FLASH_UPDATE_LENGTH_ERR\n"));
3665                 break;
3666         case FLASH_UPDATE_HW_ERR:
3667                 PM8001_MSG_DBG(pm8001_ha,
3668                         pm8001_printk(": FLASH_UPDATE_HW_ERR\n"));
3669                 break;
3670         case FLASH_UPDATE_DNLD_NOT_SUPPORTED:
3671                 PM8001_MSG_DBG(pm8001_ha,
3672                         pm8001_printk(": FLASH_UPDATE_DNLD_NOT_SUPPORTED\n"));
3673                 break;
3674         case FLASH_UPDATE_DISABLED:
3675                 PM8001_MSG_DBG(pm8001_ha,
3676                         pm8001_printk(": FLASH_UPDATE_DISABLED\n"));
3677                 break;
3678         default:
3679                 PM8001_MSG_DBG(pm8001_ha,
3680                         pm8001_printk("No matched status = %d\n", status));
3681                 break;
3682         }
3683         kfree(ccb->fw_control_context);
3684         ccb->task = NULL;
3685         ccb->ccb_tag = 0xFFFFFFFF;
3686         pm8001_tag_free(pm8001_ha, tag);
3687         complete(pm8001_ha->nvmd_completion);
3688         return 0;
3689 }
3690
3691 int pm8001_mpi_general_event(struct pm8001_hba_info *pm8001_ha , void *piomb)
3692 {
3693         u32 status;
3694         int i;
3695         struct general_event_resp *pPayload =
3696                 (struct general_event_resp *)(piomb + 4);
3697         status = le32_to_cpu(pPayload->status);
3698         PM8001_MSG_DBG(pm8001_ha,
3699                 pm8001_printk(" status = 0x%x\n", status));
3700         for (i = 0; i < GENERAL_EVENT_PAYLOAD; i++)
3701                 PM8001_MSG_DBG(pm8001_ha,
3702                         pm8001_printk("inb_IOMB_payload[0x%x] 0x%x,\n", i,
3703                         pPayload->inb_IOMB_payload[i]));
3704         return 0;
3705 }
3706
3707 int pm8001_mpi_task_abort_resp(struct pm8001_hba_info *pm8001_ha, void *piomb)
3708 {
3709         struct sas_task *t;
3710         struct pm8001_ccb_info *ccb;
3711         unsigned long flags;
3712         u32 status ;
3713         u32 tag, scp;
3714         struct task_status_struct *ts;
3715         struct pm8001_device *pm8001_dev;
3716
3717         struct task_abort_resp *pPayload =
3718                 (struct task_abort_resp *)(piomb + 4);
3719
3720         status = le32_to_cpu(pPayload->status);
3721         tag = le32_to_cpu(pPayload->tag);
3722         if (!tag) {
3723                 PM8001_FAIL_DBG(pm8001_ha,
3724                         pm8001_printk(" TAG NULL. RETURNING !!!"));
3725                 return -1;
3726         }
3727
3728         scp = le32_to_cpu(pPayload->scp);
3729         ccb = &pm8001_ha->ccb_info[tag];
3730         t = ccb->task;
3731         pm8001_dev = ccb->device; /* retrieve device */
3732
3733         if (!t) {
3734                 PM8001_FAIL_DBG(pm8001_ha,
3735                         pm8001_printk(" TASK NULL. RETURNING !!!"));
3736                 return -1;
3737         }
3738         ts = &t->task_status;
3739         if (status != 0)
3740                 PM8001_FAIL_DBG(pm8001_ha,
3741                         pm8001_printk("task abort failed status 0x%x ,"
3742                         "tag = 0x%x, scp= 0x%x\n", status, tag, scp));
3743         switch (status) {
3744         case IO_SUCCESS:
3745                 PM8001_EH_DBG(pm8001_ha, pm8001_printk("IO_SUCCESS\n"));
3746                 ts->resp = SAS_TASK_COMPLETE;
3747                 ts->stat = SAM_STAT_GOOD;
3748                 break;
3749         case IO_NOT_VALID:
3750                 PM8001_EH_DBG(pm8001_ha, pm8001_printk("IO_NOT_VALID\n"));
3751                 ts->resp = TMF_RESP_FUNC_FAILED;
3752                 break;
3753         }
3754         spin_lock_irqsave(&t->task_state_lock, flags);
3755         t->task_state_flags &= ~SAS_TASK_STATE_PENDING;
3756         t->task_state_flags &= ~SAS_TASK_AT_INITIATOR;
3757         t->task_state_flags |= SAS_TASK_STATE_DONE;
3758         spin_unlock_irqrestore(&t->task_state_lock, flags);
3759         pm8001_ccb_task_free(pm8001_ha, t, ccb, tag);
3760         mb();
3761
3762         if (pm8001_dev->id & NCQ_ABORT_ALL_FLAG) {
3763                 pm8001_tag_free(pm8001_ha, tag);
3764                 sas_free_task(t);
3765                 /* clear the flag */
3766                 pm8001_dev->id &= 0xBFFFFFFF;
3767         } else
3768                 t->task_done(t);
3769
3770         return 0;
3771 }
3772
3773 /**
3774  * mpi_hw_event -The hw event has come.
3775  * @pm8001_ha: our hba card information
3776  * @piomb: IO message buffer
3777  */
3778 static int mpi_hw_event(struct pm8001_hba_info *pm8001_ha, void* piomb)
3779 {
3780         unsigned long flags;
3781         struct hw_event_resp *pPayload =
3782                 (struct hw_event_resp *)(piomb + 4);
3783         u32 lr_evt_status_phyid_portid =
3784                 le32_to_cpu(pPayload->lr_evt_status_phyid_portid);
3785         u8 port_id = (u8)(lr_evt_status_phyid_portid & 0x0000000F);
3786         u8 phy_id =
3787                 (u8)((lr_evt_status_phyid_portid & 0x000000F0) >> 4);
3788         u16 eventType =
3789                 (u16)((lr_evt_status_phyid_portid & 0x00FFFF00) >> 8);
3790         u8 status =
3791                 (u8)((lr_evt_status_phyid_portid & 0x0F000000) >> 24);
3792         struct sas_ha_struct *sas_ha = pm8001_ha->sas;
3793         struct pm8001_phy *phy = &pm8001_ha->phy[phy_id];
3794         struct asd_sas_phy *sas_phy = sas_ha->sas_phy[phy_id];
3795         PM8001_MSG_DBG(pm8001_ha,
3796                 pm8001_printk("outbound queue HW event & event type : "));
3797         switch (eventType) {
3798         case HW_EVENT_PHY_START_STATUS:
3799                 PM8001_MSG_DBG(pm8001_ha,
3800                 pm8001_printk("HW_EVENT_PHY_START_STATUS"
3801                         " status = %x\n", status));
3802                 if (status == 0) {
3803                         phy->phy_state = 1;
3804                         if (pm8001_ha->flags == PM8001F_RUN_TIME)
3805                                 complete(phy->enable_completion);
3806                 }
3807                 break;
3808         case HW_EVENT_SAS_PHY_UP:
3809                 PM8001_MSG_DBG(pm8001_ha,
3810                         pm8001_printk("HW_EVENT_PHY_START_STATUS\n"));
3811                 hw_event_sas_phy_up(pm8001_ha, piomb);
3812                 break;
3813         case HW_EVENT_SATA_PHY_UP:
3814                 PM8001_MSG_DBG(pm8001_ha,
3815                         pm8001_printk("HW_EVENT_SATA_PHY_UP\n"));
3816                 hw_event_sata_phy_up(pm8001_ha, piomb);
3817                 break;
3818         case HW_EVENT_PHY_STOP_STATUS:
3819                 PM8001_MSG_DBG(pm8001_ha,
3820                         pm8001_printk("HW_EVENT_PHY_STOP_STATUS "
3821                         "status = %x\n", status));
3822                 if (status == 0)
3823                         phy->phy_state = 0;
3824                 break;
3825         case HW_EVENT_SATA_SPINUP_HOLD:
3826                 PM8001_MSG_DBG(pm8001_ha,
3827                         pm8001_printk("HW_EVENT_SATA_SPINUP_HOLD\n"));
3828                 sas_ha->notify_phy_event(&phy->sas_phy, PHYE_SPINUP_HOLD);
3829                 break;
3830         case HW_EVENT_PHY_DOWN:
3831                 PM8001_MSG_DBG(pm8001_ha,
3832                         pm8001_printk("HW_EVENT_PHY_DOWN\n"));
3833                 sas_ha->notify_phy_event(&phy->sas_phy, PHYE_LOSS_OF_SIGNAL);
3834                 phy->phy_attached = 0;
3835                 phy->phy_state = 0;
3836                 hw_event_phy_down(pm8001_ha, piomb);
3837                 break;
3838         case HW_EVENT_PORT_INVALID:
3839                 PM8001_MSG_DBG(pm8001_ha,
3840                         pm8001_printk("HW_EVENT_PORT_INVALID\n"));
3841                 sas_phy_disconnected(sas_phy);
3842                 phy->phy_attached = 0;
3843                 sas_ha->notify_port_event(sas_phy, PORTE_LINK_RESET_ERR);
3844                 break;
3845         /* the broadcast change primitive received, tell the LIBSAS this event
3846         to revalidate the sas domain*/
3847         case HW_EVENT_BROADCAST_CHANGE:
3848                 PM8001_MSG_DBG(pm8001_ha,
3849                         pm8001_printk("HW_EVENT_BROADCAST_CHANGE\n"));
3850                 pm8001_hw_event_ack_req(pm8001_ha, 0, HW_EVENT_BROADCAST_CHANGE,
3851                         port_id, phy_id, 1, 0);
3852                 spin_lock_irqsave(&sas_phy->sas_prim_lock, flags);
3853                 sas_phy->sas_prim = HW_EVENT_BROADCAST_CHANGE;
3854                 spin_unlock_irqrestore(&sas_phy->sas_prim_lock, flags);
3855                 sas_ha->notify_port_event(sas_phy, PORTE_BROADCAST_RCVD);
3856                 break;
3857         case HW_EVENT_PHY_ERROR:
3858                 PM8001_MSG_DBG(pm8001_ha,
3859                         pm8001_printk("HW_EVENT_PHY_ERROR\n"));
3860                 sas_phy_disconnected(&phy->sas_phy);
3861                 phy->phy_attached = 0;
3862                 sas_ha->notify_phy_event(&phy->sas_phy, PHYE_OOB_ERROR);
3863                 break;
3864         case HW_EVENT_BROADCAST_EXP:
3865                 PM8001_MSG_DBG(pm8001_ha,
3866                         pm8001_printk("HW_EVENT_BROADCAST_EXP\n"));
3867                 spin_lock_irqsave(&sas_phy->sas_prim_lock, flags);
3868                 sas_phy->sas_prim = HW_EVENT_BROADCAST_EXP;
3869                 spin_unlock_irqrestore(&sas_phy->sas_prim_lock, flags);
3870                 sas_ha->notify_port_event(sas_phy, PORTE_BROADCAST_RCVD);
3871                 break;
3872         case HW_EVENT_LINK_ERR_INVALID_DWORD:
3873                 PM8001_MSG_DBG(pm8001_ha,
3874                         pm8001_printk("HW_EVENT_LINK_ERR_INVALID_DWORD\n"));
3875                 pm8001_hw_event_ack_req(pm8001_ha, 0,
3876                         HW_EVENT_LINK_ERR_INVALID_DWORD, port_id, phy_id, 0, 0);
3877                 sas_phy_disconnected(sas_phy);
3878                 phy->phy_attached = 0;
3879                 sas_ha->notify_port_event(sas_phy, PORTE_LINK_RESET_ERR);
3880                 break;
3881         case HW_EVENT_LINK_ERR_DISPARITY_ERROR:
3882                 PM8001_MSG_DBG(pm8001_ha,
3883                         pm8001_printk("HW_EVENT_LINK_ERR_DISPARITY_ERROR\n"));
3884                 pm8001_hw_event_ack_req(pm8001_ha, 0,
3885                         HW_EVENT_LINK_ERR_DISPARITY_ERROR,
3886                         port_id, phy_id, 0, 0);
3887                 sas_phy_disconnected(sas_phy);
3888                 phy->phy_attached = 0;
3889                 sas_ha->notify_port_event(sas_phy, PORTE_LINK_RESET_ERR);
3890                 break;
3891         case HW_EVENT_LINK_ERR_CODE_VIOLATION:
3892                 PM8001_MSG_DBG(pm8001_ha,
3893                         pm8001_printk("HW_EVENT_LINK_ERR_CODE_VIOLATION\n"));
3894                 pm8001_hw_event_ack_req(pm8001_ha, 0,
3895                         HW_EVENT_LINK_ERR_CODE_VIOLATION,
3896                         port_id, phy_id, 0, 0);
3897                 sas_phy_disconnected(sas_phy);
3898                 phy->phy_attached = 0;
3899                 sas_ha->notify_port_event(sas_phy, PORTE_LINK_RESET_ERR);
3900                 break;
3901         case HW_EVENT_LINK_ERR_LOSS_OF_DWORD_SYNCH:
3902                 PM8001_MSG_DBG(pm8001_ha,
3903                       pm8001_printk("HW_EVENT_LINK_ERR_LOSS_OF_DWORD_SYNCH\n"));
3904                 pm8001_hw_event_ack_req(pm8001_ha, 0,
3905                         HW_EVENT_LINK_ERR_LOSS_OF_DWORD_SYNCH,
3906                         port_id, phy_id, 0, 0);
3907                 sas_phy_disconnected(sas_phy);
3908                 phy->phy_attached = 0;
3909                 sas_ha->notify_port_event(sas_phy, PORTE_LINK_RESET_ERR);
3910                 break;
3911         case HW_EVENT_MALFUNCTION:
3912                 PM8001_MSG_DBG(pm8001_ha,
3913                         pm8001_printk("HW_EVENT_MALFUNCTION\n"));
3914                 break;
3915         case HW_EVENT_BROADCAST_SES:
3916                 PM8001_MSG_DBG(pm8001_ha,
3917                         pm8001_printk("HW_EVENT_BROADCAST_SES\n"));
3918                 spin_lock_irqsave(&sas_phy->sas_prim_lock, flags);
3919                 sas_phy->sas_prim = HW_EVENT_BROADCAST_SES;
3920                 spin_unlock_irqrestore(&sas_phy->sas_prim_lock, flags);
3921                 sas_ha->notify_port_event(sas_phy, PORTE_BROADCAST_RCVD);
3922                 break;
3923         case HW_EVENT_INBOUND_CRC_ERROR:
3924                 PM8001_MSG_DBG(pm8001_ha,
3925                         pm8001_printk("HW_EVENT_INBOUND_CRC_ERROR\n"));
3926                 pm8001_hw_event_ack_req(pm8001_ha, 0,
3927                         HW_EVENT_INBOUND_CRC_ERROR,
3928                         port_id, phy_id, 0, 0);
3929                 break;
3930         case HW_EVENT_HARD_RESET_RECEIVED:
3931                 PM8001_MSG_DBG(pm8001_ha,
3932                         pm8001_printk("HW_EVENT_HARD_RESET_RECEIVED\n"));
3933                 sas_ha->notify_port_event(sas_phy, PORTE_HARD_RESET);
3934                 break;
3935         case HW_EVENT_ID_FRAME_TIMEOUT:
3936                 PM8001_MSG_DBG(pm8001_ha,
3937                         pm8001_printk("HW_EVENT_ID_FRAME_TIMEOUT\n"));
3938                 sas_phy_disconnected(sas_phy);
3939                 phy->phy_attached = 0;
3940                 sas_ha->notify_port_event(sas_phy, PORTE_LINK_RESET_ERR);
3941                 break;
3942         case HW_EVENT_LINK_ERR_PHY_RESET_FAILED:
3943                 PM8001_MSG_DBG(pm8001_ha,
3944                         pm8001_printk("HW_EVENT_LINK_ERR_PHY_RESET_FAILED\n"));
3945                 pm8001_hw_event_ack_req(pm8001_ha, 0,
3946                         HW_EVENT_LINK_ERR_PHY_RESET_FAILED,
3947                         port_id, phy_id, 0, 0);
3948                 sas_phy_disconnected(sas_phy);
3949                 phy->phy_attached = 0;
3950                 sas_ha->notify_port_event(sas_phy, PORTE_LINK_RESET_ERR);
3951                 break;
3952         case HW_EVENT_PORT_RESET_TIMER_TMO:
3953                 PM8001_MSG_DBG(pm8001_ha,
3954                         pm8001_printk("HW_EVENT_PORT_RESET_TIMER_TMO\n"));
3955                 sas_phy_disconnected(sas_phy);
3956                 phy->phy_attached = 0;
3957                 sas_ha->notify_port_event(sas_phy, PORTE_LINK_RESET_ERR);
3958                 break;
3959         case HW_EVENT_PORT_RECOVERY_TIMER_TMO:
3960                 PM8001_MSG_DBG(pm8001_ha,
3961                         pm8001_printk("HW_EVENT_PORT_RECOVERY_TIMER_TMO\n"));
3962                 sas_phy_disconnected(sas_phy);
3963                 phy->phy_attached = 0;
3964                 sas_ha->notify_port_event(sas_phy, PORTE_LINK_RESET_ERR);
3965                 break;
3966         case HW_EVENT_PORT_RECOVER:
3967                 PM8001_MSG_DBG(pm8001_ha,
3968                         pm8001_printk("HW_EVENT_PORT_RECOVER\n"));
3969                 break;
3970         case HW_EVENT_PORT_RESET_COMPLETE:
3971                 PM8001_MSG_DBG(pm8001_ha,
3972                         pm8001_printk("HW_EVENT_PORT_RESET_COMPLETE\n"));
3973                 break;
3974         case EVENT_BROADCAST_ASYNCH_EVENT:
3975                 PM8001_MSG_DBG(pm8001_ha,
3976                         pm8001_printk("EVENT_BROADCAST_ASYNCH_EVENT\n"));
3977                 break;
3978         default:
3979                 PM8001_MSG_DBG(pm8001_ha,
3980                         pm8001_printk("Unknown event type = %x\n", eventType));
3981                 break;
3982         }
3983         return 0;
3984 }
3985
3986 /**
3987  * process_one_iomb - process one outbound Queue memory block
3988  * @pm8001_ha: our hba card information
3989  * @piomb: IO message buffer
3990  */
3991 static void process_one_iomb(struct pm8001_hba_info *pm8001_ha, void *piomb)
3992 {
3993         __le32 pHeader = *(__le32 *)piomb;
3994         u8 opc = (u8)((le32_to_cpu(pHeader)) & 0xFFF);
3995
3996         PM8001_MSG_DBG(pm8001_ha, pm8001_printk("process_one_iomb:"));
3997
3998         switch (opc) {
3999         case OPC_OUB_ECHO:
4000                 PM8001_MSG_DBG(pm8001_ha, pm8001_printk("OPC_OUB_ECHO\n"));
4001                 break;
4002         case OPC_OUB_HW_EVENT:
4003                 PM8001_MSG_DBG(pm8001_ha,
4004                         pm8001_printk("OPC_OUB_HW_EVENT\n"));
4005                 mpi_hw_event(pm8001_ha, piomb);
4006                 break;
4007         case OPC_OUB_SSP_COMP:
4008                 PM8001_MSG_DBG(pm8001_ha,
4009                         pm8001_printk("OPC_OUB_SSP_COMP\n"));
4010                 mpi_ssp_completion(pm8001_ha, piomb);
4011                 break;
4012         case OPC_OUB_SMP_COMP:
4013                 PM8001_MSG_DBG(pm8001_ha,
4014                         pm8001_printk("OPC_OUB_SMP_COMP\n"));
4015                 mpi_smp_completion(pm8001_ha, piomb);
4016                 break;
4017         case OPC_OUB_LOCAL_PHY_CNTRL:
4018                 PM8001_MSG_DBG(pm8001_ha,
4019                         pm8001_printk("OPC_OUB_LOCAL_PHY_CNTRL\n"));
4020                 pm8001_mpi_local_phy_ctl(pm8001_ha, piomb);
4021                 break;
4022         case OPC_OUB_DEV_REGIST:
4023                 PM8001_MSG_DBG(pm8001_ha,
4024                         pm8001_printk("OPC_OUB_DEV_REGIST\n"));
4025                 pm8001_mpi_reg_resp(pm8001_ha, piomb);
4026                 break;
4027         case OPC_OUB_DEREG_DEV:
4028                 PM8001_MSG_DBG(pm8001_ha,
4029                         pm8001_printk("unregister the device\n"));
4030                 pm8001_mpi_dereg_resp(pm8001_ha, piomb);
4031                 break;
4032         case OPC_OUB_GET_DEV_HANDLE:
4033                 PM8001_MSG_DBG(pm8001_ha,
4034                         pm8001_printk("OPC_OUB_GET_DEV_HANDLE\n"));
4035                 break;
4036         case OPC_OUB_SATA_COMP:
4037                 PM8001_MSG_DBG(pm8001_ha,
4038                         pm8001_printk("OPC_OUB_SATA_COMP\n"));
4039                 mpi_sata_completion(pm8001_ha, piomb);
4040                 break;
4041         case OPC_OUB_SATA_EVENT:
4042                 PM8001_MSG_DBG(pm8001_ha,
4043                         pm8001_printk("OPC_OUB_SATA_EVENT\n"));
4044                 mpi_sata_event(pm8001_ha, piomb);
4045                 break;
4046         case OPC_OUB_SSP_EVENT:
4047                 PM8001_MSG_DBG(pm8001_ha,
4048                         pm8001_printk("OPC_OUB_SSP_EVENT\n"));
4049                 mpi_ssp_event(pm8001_ha, piomb);
4050                 break;
4051         case OPC_OUB_DEV_HANDLE_ARRIV:
4052                 PM8001_MSG_DBG(pm8001_ha,
4053                         pm8001_printk("OPC_OUB_DEV_HANDLE_ARRIV\n"));
4054                 /*This is for target*/
4055                 break;
4056         case OPC_OUB_SSP_RECV_EVENT:
4057                 PM8001_MSG_DBG(pm8001_ha,
4058                         pm8001_printk("OPC_OUB_SSP_RECV_EVENT\n"));
4059                 /*This is for target*/
4060                 break;
4061         case OPC_OUB_DEV_INFO:
4062                 PM8001_MSG_DBG(pm8001_ha,
4063                         pm8001_printk("OPC_OUB_DEV_INFO\n"));
4064                 break;
4065         case OPC_OUB_FW_FLASH_UPDATE:
4066                 PM8001_MSG_DBG(pm8001_ha,
4067                         pm8001_printk("OPC_OUB_FW_FLASH_UPDATE\n"));
4068                 pm8001_mpi_fw_flash_update_resp(pm8001_ha, piomb);
4069                 break;
4070         case OPC_OUB_GPIO_RESPONSE:
4071                 PM8001_MSG_DBG(pm8001_ha,
4072                         pm8001_printk("OPC_OUB_GPIO_RESPONSE\n"));
4073                 break;
4074         case OPC_OUB_GPIO_EVENT:
4075                 PM8001_MSG_DBG(pm8001_ha,
4076                         pm8001_printk("OPC_OUB_GPIO_EVENT\n"));
4077                 break;
4078         case OPC_OUB_GENERAL_EVENT:
4079                 PM8001_MSG_DBG(pm8001_ha,
4080                         pm8001_printk("OPC_OUB_GENERAL_EVENT\n"));
4081                 pm8001_mpi_general_event(pm8001_ha, piomb);
4082                 break;
4083         case OPC_OUB_SSP_ABORT_RSP:
4084                 PM8001_MSG_DBG(pm8001_ha,
4085                         pm8001_printk("OPC_OUB_SSP_ABORT_RSP\n"));
4086                 pm8001_mpi_task_abort_resp(pm8001_ha, piomb);
4087                 break;
4088         case OPC_OUB_SATA_ABORT_RSP:
4089                 PM8001_MSG_DBG(pm8001_ha,
4090                         pm8001_printk("OPC_OUB_SATA_ABORT_RSP\n"));
4091                 pm8001_mpi_task_abort_resp(pm8001_ha, piomb);
4092                 break;
4093         case OPC_OUB_SAS_DIAG_MODE_START_END:
4094                 PM8001_MSG_DBG(pm8001_ha,
4095                         pm8001_printk("OPC_OUB_SAS_DIAG_MODE_START_END\n"));
4096                 break;
4097         case OPC_OUB_SAS_DIAG_EXECUTE:
4098                 PM8001_MSG_DBG(pm8001_ha,
4099                         pm8001_printk("OPC_OUB_SAS_DIAG_EXECUTE\n"));
4100                 break;
4101         case OPC_OUB_GET_TIME_STAMP:
4102                 PM8001_MSG_DBG(pm8001_ha,
4103                         pm8001_printk("OPC_OUB_GET_TIME_STAMP\n"));
4104                 break;
4105         case OPC_OUB_SAS_HW_EVENT_ACK:
4106                 PM8001_MSG_DBG(pm8001_ha,
4107                         pm8001_printk("OPC_OUB_SAS_HW_EVENT_ACK\n"));
4108                 break;
4109         case OPC_OUB_PORT_CONTROL:
4110                 PM8001_MSG_DBG(pm8001_ha,
4111                         pm8001_printk("OPC_OUB_PORT_CONTROL\n"));
4112                 break;
4113         case OPC_OUB_SMP_ABORT_RSP:
4114                 PM8001_MSG_DBG(pm8001_ha,
4115                         pm8001_printk("OPC_OUB_SMP_ABORT_RSP\n"));
4116                 pm8001_mpi_task_abort_resp(pm8001_ha, piomb);
4117                 break;
4118         case OPC_OUB_GET_NVMD_DATA:
4119                 PM8001_MSG_DBG(pm8001_ha,
4120                         pm8001_printk("OPC_OUB_GET_NVMD_DATA\n"));
4121                 pm8001_mpi_get_nvmd_resp(pm8001_ha, piomb);
4122                 break;
4123         case OPC_OUB_SET_NVMD_DATA:
4124                 PM8001_MSG_DBG(pm8001_ha,
4125                         pm8001_printk("OPC_OUB_SET_NVMD_DATA\n"));
4126                 pm8001_mpi_set_nvmd_resp(pm8001_ha, piomb);
4127                 break;
4128         case OPC_OUB_DEVICE_HANDLE_REMOVAL:
4129                 PM8001_MSG_DBG(pm8001_ha,
4130                         pm8001_printk("OPC_OUB_DEVICE_HANDLE_REMOVAL\n"));
4131                 break;
4132         case OPC_OUB_SET_DEVICE_STATE:
4133                 PM8001_MSG_DBG(pm8001_ha,
4134                         pm8001_printk("OPC_OUB_SET_DEVICE_STATE\n"));
4135                 pm8001_mpi_set_dev_state_resp(pm8001_ha, piomb);
4136                 break;
4137         case OPC_OUB_GET_DEVICE_STATE:
4138                 PM8001_MSG_DBG(pm8001_ha,
4139                         pm8001_printk("OPC_OUB_GET_DEVICE_STATE\n"));
4140                 break;
4141         case OPC_OUB_SET_DEV_INFO:
4142                 PM8001_MSG_DBG(pm8001_ha,
4143                         pm8001_printk("OPC_OUB_SET_DEV_INFO\n"));
4144                 break;
4145         case OPC_OUB_SAS_RE_INITIALIZE:
4146                 PM8001_MSG_DBG(pm8001_ha,
4147                         pm8001_printk("OPC_OUB_SAS_RE_INITIALIZE\n"));
4148                 break;
4149         default:
4150                 PM8001_MSG_DBG(pm8001_ha,
4151                         pm8001_printk("Unknown outbound Queue IOMB OPC = %x\n",
4152                         opc));
4153                 break;
4154         }
4155 }
4156
4157 static int process_oq(struct pm8001_hba_info *pm8001_ha, u8 vec)
4158 {
4159         struct outbound_queue_table *circularQ;
4160         void *pMsg1 = NULL;
4161         u8 uninitialized_var(bc);
4162         u32 ret = MPI_IO_STATUS_FAIL;
4163         unsigned long flags;
4164
4165         spin_lock_irqsave(&pm8001_ha->lock, flags);
4166         circularQ = &pm8001_ha->outbnd_q_tbl[vec];
4167         do {
4168                 ret = pm8001_mpi_msg_consume(pm8001_ha, circularQ, &pMsg1, &bc);
4169                 if (MPI_IO_STATUS_SUCCESS == ret) {
4170                         /* process the outbound message */
4171                         process_one_iomb(pm8001_ha, (void *)(pMsg1 - 4));
4172                         /* free the message from the outbound circular buffer */
4173                         pm8001_mpi_msg_free_set(pm8001_ha, pMsg1,
4174                                                         circularQ, bc);
4175                 }
4176                 if (MPI_IO_STATUS_BUSY == ret) {
4177                         /* Update the producer index from SPC */
4178                         circularQ->producer_index =
4179                                 cpu_to_le32(pm8001_read_32(circularQ->pi_virt));
4180                         if (le32_to_cpu(circularQ->producer_index) ==
4181                                 circularQ->consumer_idx)
4182                                 /* OQ is empty */
4183                                 break;
4184                 }
4185         } while (1);
4186         spin_unlock_irqrestore(&pm8001_ha->lock, flags);
4187         return ret;
4188 }
4189
4190 /* PCI_DMA_... to our direction translation. */
4191 static const u8 data_dir_flags[] = {
4192         [PCI_DMA_BIDIRECTIONAL] = DATA_DIR_BYRECIPIENT,/* UNSPECIFIED */
4193         [PCI_DMA_TODEVICE]      = DATA_DIR_OUT,/* OUTBOUND */
4194         [PCI_DMA_FROMDEVICE]    = DATA_DIR_IN,/* INBOUND */
4195         [PCI_DMA_NONE]          = DATA_DIR_NONE,/* NO TRANSFER */
4196 };
4197 void
4198 pm8001_chip_make_sg(struct scatterlist *scatter, int nr, void *prd)
4199 {
4200         int i;
4201         struct scatterlist *sg;
4202         struct pm8001_prd *buf_prd = prd;
4203
4204         for_each_sg(scatter, sg, nr, i) {
4205                 buf_prd->addr = cpu_to_le64(sg_dma_address(sg));
4206                 buf_prd->im_len.len = cpu_to_le32(sg_dma_len(sg));
4207                 buf_prd->im_len.e = 0;
4208                 buf_prd++;
4209         }
4210 }
4211
4212 static void build_smp_cmd(u32 deviceID, __le32 hTag, struct smp_req *psmp_cmd)
4213 {
4214         psmp_cmd->tag = hTag;
4215         psmp_cmd->device_id = cpu_to_le32(deviceID);
4216         psmp_cmd->len_ip_ir = cpu_to_le32(1|(1 << 1));
4217 }
4218
4219 /**
4220  * pm8001_chip_smp_req - send a SMP task to FW
4221  * @pm8001_ha: our hba card information.
4222  * @ccb: the ccb information this request used.
4223  */
4224 static int pm8001_chip_smp_req(struct pm8001_hba_info *pm8001_ha,
4225         struct pm8001_ccb_info *ccb)
4226 {
4227         int elem, rc;
4228         struct sas_task *task = ccb->task;
4229         struct domain_device *dev = task->dev;
4230         struct pm8001_device *pm8001_dev = dev->lldd_dev;
4231         struct scatterlist *sg_req, *sg_resp;
4232         u32 req_len, resp_len;
4233         struct smp_req smp_cmd;
4234         u32 opc;
4235         struct inbound_queue_table *circularQ;
4236
4237         memset(&smp_cmd, 0, sizeof(smp_cmd));
4238         /*
4239          * DMA-map SMP request, response buffers
4240          */
4241         sg_req = &task->smp_task.smp_req;
4242         elem = dma_map_sg(pm8001_ha->dev, sg_req, 1, PCI_DMA_TODEVICE);
4243         if (!elem)
4244                 return -ENOMEM;
4245         req_len = sg_dma_len(sg_req);
4246
4247         sg_resp = &task->smp_task.smp_resp;
4248         elem = dma_map_sg(pm8001_ha->dev, sg_resp, 1, PCI_DMA_FROMDEVICE);
4249         if (!elem) {
4250                 rc = -ENOMEM;
4251                 goto err_out;
4252         }
4253         resp_len = sg_dma_len(sg_resp);
4254         /* must be in dwords */
4255         if ((req_len & 0x3) || (resp_len & 0x3)) {
4256                 rc = -EINVAL;
4257                 goto err_out_2;
4258         }
4259
4260         opc = OPC_INB_SMP_REQUEST;
4261         circularQ = &pm8001_ha->inbnd_q_tbl[0];
4262         smp_cmd.tag = cpu_to_le32(ccb->ccb_tag);
4263         smp_cmd.long_smp_req.long_req_addr =
4264                 cpu_to_le64((u64)sg_dma_address(&task->smp_task.smp_req));
4265         smp_cmd.long_smp_req.long_req_size =
4266                 cpu_to_le32((u32)sg_dma_len(&task->smp_task.smp_req)-4);
4267         smp_cmd.long_smp_req.long_resp_addr =
4268                 cpu_to_le64((u64)sg_dma_address(&task->smp_task.smp_resp));
4269         smp_cmd.long_smp_req.long_resp_size =
4270                 cpu_to_le32((u32)sg_dma_len(&task->smp_task.smp_resp)-4);
4271         build_smp_cmd(pm8001_dev->device_id, smp_cmd.tag, &smp_cmd);
4272         rc = pm8001_mpi_build_cmd(pm8001_ha, circularQ, opc,
4273                                         (u32 *)&smp_cmd, 0);
4274         if (rc)
4275                 goto err_out_2;
4276
4277         return 0;
4278
4279 err_out_2:
4280         dma_unmap_sg(pm8001_ha->dev, &ccb->task->smp_task.smp_resp, 1,
4281                         PCI_DMA_FROMDEVICE);
4282 err_out:
4283         dma_unmap_sg(pm8001_ha->dev, &ccb->task->smp_task.smp_req, 1,
4284                         PCI_DMA_TODEVICE);
4285         return rc;
4286 }
4287
4288 /**
4289  * pm8001_chip_ssp_io_req - send a SSP task to FW
4290  * @pm8001_ha: our hba card information.
4291  * @ccb: the ccb information this request used.
4292  */
4293 static int pm8001_chip_ssp_io_req(struct pm8001_hba_info *pm8001_ha,
4294         struct pm8001_ccb_info *ccb)
4295 {
4296         struct sas_task *task = ccb->task;
4297         struct domain_device *dev = task->dev;
4298         struct pm8001_device *pm8001_dev = dev->lldd_dev;
4299         struct ssp_ini_io_start_req ssp_cmd;
4300         u32 tag = ccb->ccb_tag;
4301         int ret;
4302         u64 phys_addr;
4303         struct inbound_queue_table *circularQ;
4304         u32 opc = OPC_INB_SSPINIIOSTART;
4305         memset(&ssp_cmd, 0, sizeof(ssp_cmd));
4306         memcpy(ssp_cmd.ssp_iu.lun, task->ssp_task.LUN, 8);
4307         ssp_cmd.dir_m_tlr =
4308                 cpu_to_le32(data_dir_flags[task->data_dir] << 8 | 0x0);/*0 for
4309         SAS 1.1 compatible TLR*/
4310         ssp_cmd.data_len = cpu_to_le32(task->total_xfer_len);
4311         ssp_cmd.device_id = cpu_to_le32(pm8001_dev->device_id);
4312         ssp_cmd.tag = cpu_to_le32(tag);
4313         if (task->ssp_task.enable_first_burst)
4314                 ssp_cmd.ssp_iu.efb_prio_attr |= 0x80;
4315         ssp_cmd.ssp_iu.efb_prio_attr |= (task->ssp_task.task_prio << 3);
4316         ssp_cmd.ssp_iu.efb_prio_attr |= (task->ssp_task.task_attr & 7);
4317         memcpy(ssp_cmd.ssp_iu.cdb, task->ssp_task.cmd->cmnd,
4318                task->ssp_task.cmd->cmd_len);
4319         circularQ = &pm8001_ha->inbnd_q_tbl[0];
4320
4321         /* fill in PRD (scatter/gather) table, if any */
4322         if (task->num_scatter > 1) {
4323                 pm8001_chip_make_sg(task->scatter, ccb->n_elem, ccb->buf_prd);
4324                 phys_addr = ccb->ccb_dma_handle +
4325                                 offsetof(struct pm8001_ccb_info, buf_prd[0]);
4326                 ssp_cmd.addr_low = cpu_to_le32(lower_32_bits(phys_addr));
4327                 ssp_cmd.addr_high = cpu_to_le32(upper_32_bits(phys_addr));
4328                 ssp_cmd.esgl = cpu_to_le32(1<<31);
4329         } else if (task->num_scatter == 1) {
4330                 u64 dma_addr = sg_dma_address(task->scatter);
4331                 ssp_cmd.addr_low = cpu_to_le32(lower_32_bits(dma_addr));
4332                 ssp_cmd.addr_high = cpu_to_le32(upper_32_bits(dma_addr));
4333                 ssp_cmd.len = cpu_to_le32(task->total_xfer_len);
4334                 ssp_cmd.esgl = 0;
4335         } else if (task->num_scatter == 0) {
4336                 ssp_cmd.addr_low = 0;
4337                 ssp_cmd.addr_high = 0;
4338                 ssp_cmd.len = cpu_to_le32(task->total_xfer_len);
4339                 ssp_cmd.esgl = 0;
4340         }
4341         ret = pm8001_mpi_build_cmd(pm8001_ha, circularQ, opc, &ssp_cmd, 0);
4342         return ret;
4343 }
4344
4345 static int pm8001_chip_sata_req(struct pm8001_hba_info *pm8001_ha,
4346         struct pm8001_ccb_info *ccb)
4347 {
4348         struct sas_task *task = ccb->task;
4349         struct domain_device *dev = task->dev;
4350         struct pm8001_device *pm8001_ha_dev = dev->lldd_dev;
4351         u32 tag = ccb->ccb_tag;
4352         int ret;
4353         struct sata_start_req sata_cmd;
4354         u32 hdr_tag, ncg_tag = 0;
4355         u64 phys_addr;
4356         u32 ATAP = 0x0;
4357         u32 dir;
4358         struct inbound_queue_table *circularQ;
4359         unsigned long flags;
4360         u32  opc = OPC_INB_SATA_HOST_OPSTART;
4361         memset(&sata_cmd, 0, sizeof(sata_cmd));
4362         circularQ = &pm8001_ha->inbnd_q_tbl[0];
4363         if (task->data_dir == PCI_DMA_NONE) {
4364                 ATAP = 0x04;  /* no data*/
4365                 PM8001_IO_DBG(pm8001_ha, pm8001_printk("no data\n"));
4366         } else if (likely(!task->ata_task.device_control_reg_update)) {
4367                 if (task->ata_task.dma_xfer) {
4368                         ATAP = 0x06; /* DMA */
4369                         PM8001_IO_DBG(pm8001_ha, pm8001_printk("DMA\n"));
4370                 } else {
4371                         ATAP = 0x05; /* PIO*/
4372                         PM8001_IO_DBG(pm8001_ha, pm8001_printk("PIO\n"));
4373                 }
4374                 if (task->ata_task.use_ncq &&
4375                         dev->sata_dev.class != ATA_DEV_ATAPI) {
4376                         ATAP = 0x07; /* FPDMA */
4377                         PM8001_IO_DBG(pm8001_ha, pm8001_printk("FPDMA\n"));
4378                 }
4379         }
4380         if (task->ata_task.use_ncq && pm8001_get_ncq_tag(task, &hdr_tag)) {
4381                 task->ata_task.fis.sector_count |= (u8) (hdr_tag << 3);
4382                 ncg_tag = hdr_tag;
4383         }
4384         dir = data_dir_flags[task->data_dir] << 8;
4385         sata_cmd.tag = cpu_to_le32(tag);
4386         sata_cmd.device_id = cpu_to_le32(pm8001_ha_dev->device_id);
4387         sata_cmd.data_len = cpu_to_le32(task->total_xfer_len);
4388         sata_cmd.ncqtag_atap_dir_m =
4389                 cpu_to_le32(((ncg_tag & 0xff)<<16)|((ATAP & 0x3f) << 10) | dir);
4390         sata_cmd.sata_fis = task->ata_task.fis;
4391         if (likely(!task->ata_task.device_control_reg_update))
4392                 sata_cmd.sata_fis.flags |= 0x80;/* C=1: update ATA cmd reg */
4393         sata_cmd.sata_fis.flags &= 0xF0;/* PM_PORT field shall be 0 */
4394         /* fill in PRD (scatter/gather) table, if any */
4395         if (task->num_scatter > 1) {
4396                 pm8001_chip_make_sg(task->scatter, ccb->n_elem, ccb->buf_prd);
4397                 phys_addr = ccb->ccb_dma_handle +
4398                                 offsetof(struct pm8001_ccb_info, buf_prd[0]);
4399                 sata_cmd.addr_low = lower_32_bits(phys_addr);
4400                 sata_cmd.addr_high = upper_32_bits(phys_addr);
4401                 sata_cmd.esgl = cpu_to_le32(1 << 31);
4402         } else if (task->num_scatter == 1) {
4403                 u64 dma_addr = sg_dma_address(task->scatter);
4404                 sata_cmd.addr_low = lower_32_bits(dma_addr);
4405                 sata_cmd.addr_high = upper_32_bits(dma_addr);
4406                 sata_cmd.len = cpu_to_le32(task->total_xfer_len);
4407                 sata_cmd.esgl = 0;
4408         } else if (task->num_scatter == 0) {
4409                 sata_cmd.addr_low = 0;
4410                 sata_cmd.addr_high = 0;
4411                 sata_cmd.len = cpu_to_le32(task->total_xfer_len);
4412                 sata_cmd.esgl = 0;
4413         }
4414
4415         /* Check for read log for failed drive and return */
4416         if (sata_cmd.sata_fis.command == 0x2f) {
4417                 if (((pm8001_ha_dev->id & NCQ_READ_LOG_FLAG) ||
4418                         (pm8001_ha_dev->id & NCQ_ABORT_ALL_FLAG) ||
4419                         (pm8001_ha_dev->id & NCQ_2ND_RLE_FLAG))) {
4420                         struct task_status_struct *ts;
4421
4422                         pm8001_ha_dev->id &= 0xDFFFFFFF;
4423                         ts = &task->task_status;
4424
4425                         spin_lock_irqsave(&task->task_state_lock, flags);
4426                         ts->resp = SAS_TASK_COMPLETE;
4427                         ts->stat = SAM_STAT_GOOD;
4428                         task->task_state_flags &= ~SAS_TASK_STATE_PENDING;
4429                         task->task_state_flags &= ~SAS_TASK_AT_INITIATOR;
4430                         task->task_state_flags |= SAS_TASK_STATE_DONE;
4431                         if (unlikely((task->task_state_flags &
4432                                         SAS_TASK_STATE_ABORTED))) {
4433                                 spin_unlock_irqrestore(&task->task_state_lock,
4434                                                         flags);
4435                                 PM8001_FAIL_DBG(pm8001_ha,
4436                                         pm8001_printk("task 0x%p resp 0x%x "
4437                                         " stat 0x%x but aborted by upper layer "
4438                                         "\n", task, ts->resp, ts->stat));
4439                                 pm8001_ccb_task_free(pm8001_ha, task, ccb, tag);
4440                         } else {
4441                                 spin_unlock_irqrestore(&task->task_state_lock,
4442                                                         flags);
4443                                 pm8001_ccb_task_free_done(pm8001_ha, task,
4444                                                                 ccb, tag);
4445                                 return 0;
4446                         }
4447                 }
4448         }
4449
4450         ret = pm8001_mpi_build_cmd(pm8001_ha, circularQ, opc, &sata_cmd, 0);
4451         return ret;
4452 }
4453
4454 /**
4455  * pm8001_chip_phy_start_req - start phy via PHY_START COMMAND
4456  * @pm8001_ha: our hba card information.
4457  * @num: the inbound queue number
4458  * @phy_id: the phy id which we wanted to start up.
4459  */
4460 static int
4461 pm8001_chip_phy_start_req(struct pm8001_hba_info *pm8001_ha, u8 phy_id)
4462 {
4463         struct phy_start_req payload;
4464         struct inbound_queue_table *circularQ;
4465         int ret;
4466         u32 tag = 0x01;
4467         u32 opcode = OPC_INB_PHYSTART;
4468         circularQ = &pm8001_ha->inbnd_q_tbl[0];
4469         memset(&payload, 0, sizeof(payload));
4470         payload.tag = cpu_to_le32(tag);
4471         /*
4472          ** [0:7]   PHY Identifier
4473          ** [8:11]  link rate 1.5G, 3G, 6G
4474          ** [12:13] link mode 01b SAS mode; 10b SATA mode; 11b both
4475          ** [14]    0b disable spin up hold; 1b enable spin up hold
4476          */
4477         payload.ase_sh_lm_slr_phyid = cpu_to_le32(SPINHOLD_DISABLE |
4478                 LINKMODE_AUTO | LINKRATE_15 |
4479                 LINKRATE_30 | LINKRATE_60 | phy_id);
4480         payload.sas_identify.dev_type = SAS_END_DEVICE;
4481         payload.sas_identify.initiator_bits = SAS_PROTOCOL_ALL;
4482         memcpy(payload.sas_identify.sas_addr,
4483                 pm8001_ha->sas_addr, SAS_ADDR_SIZE);
4484         payload.sas_identify.phy_id = phy_id;
4485         ret = pm8001_mpi_build_cmd(pm8001_ha, circularQ, opcode, &payload, 0);
4486         return ret;
4487 }
4488
4489 /**
4490  * pm8001_chip_phy_stop_req - start phy via PHY_STOP COMMAND
4491  * @pm8001_ha: our hba card information.
4492  * @num: the inbound queue number
4493  * @phy_id: the phy id which we wanted to start up.
4494  */
4495 int pm8001_chip_phy_stop_req(struct pm8001_hba_info *pm8001_ha,
4496         u8 phy_id)
4497 {
4498         struct phy_stop_req payload;
4499         struct inbound_queue_table *circularQ;
4500         int ret;
4501         u32 tag = 0x01;
4502         u32 opcode = OPC_INB_PHYSTOP;
4503         circularQ = &pm8001_ha->inbnd_q_tbl[0];
4504         memset(&payload, 0, sizeof(payload));
4505         payload.tag = cpu_to_le32(tag);
4506         payload.phy_id = cpu_to_le32(phy_id);
4507         ret = pm8001_mpi_build_cmd(pm8001_ha, circularQ, opcode, &payload, 0);
4508         return ret;
4509 }
4510
4511 /**
4512  * see comments on pm8001_mpi_reg_resp.
4513  */
4514 static int pm8001_chip_reg_dev_req(struct pm8001_hba_info *pm8001_ha,
4515         struct pm8001_device *pm8001_dev, u32 flag)
4516 {
4517         struct reg_dev_req payload;
4518         u32     opc;
4519         u32 stp_sspsmp_sata = 0x4;
4520         struct inbound_queue_table *circularQ;
4521         u32 linkrate, phy_id;
4522         int rc, tag = 0xdeadbeef;
4523         struct pm8001_ccb_info *ccb;
4524         u8 retryFlag = 0x1;
4525         u16 firstBurstSize = 0;
4526         u16 ITNT = 2000;
4527         struct domain_device *dev = pm8001_dev->sas_device;
4528         struct domain_device *parent_dev = dev->parent;
4529         circularQ = &pm8001_ha->inbnd_q_tbl[0];
4530
4531         memset(&payload, 0, sizeof(payload));
4532         rc = pm8001_tag_alloc(pm8001_ha, &tag);
4533         if (rc)
4534                 return rc;
4535         ccb = &pm8001_ha->ccb_info[tag];
4536         ccb->device = pm8001_dev;
4537         ccb->ccb_tag = tag;
4538         payload.tag = cpu_to_le32(tag);
4539         if (flag == 1)
4540                 stp_sspsmp_sata = 0x02; /*direct attached sata */
4541         else {
4542                 if (pm8001_dev->dev_type == SAS_SATA_DEV)
4543                         stp_sspsmp_sata = 0x00; /* stp*/
4544                 else if (pm8001_dev->dev_type == SAS_END_DEVICE ||
4545                         pm8001_dev->dev_type == SAS_EDGE_EXPANDER_DEVICE ||
4546                         pm8001_dev->dev_type == SAS_FANOUT_EXPANDER_DEVICE)
4547                         stp_sspsmp_sata = 0x01; /*ssp or smp*/
4548         }
4549         if (parent_dev && DEV_IS_EXPANDER(parent_dev->dev_type))
4550                 phy_id = parent_dev->ex_dev.ex_phy->phy_id;
4551         else
4552                 phy_id = pm8001_dev->attached_phy;
4553         opc = OPC_INB_REG_DEV;
4554         linkrate = (pm8001_dev->sas_device->linkrate < dev->port->linkrate) ?
4555                         pm8001_dev->sas_device->linkrate : dev->port->linkrate;
4556         payload.phyid_portid =
4557                 cpu_to_le32(((pm8001_dev->sas_device->port->id) & 0x0F) |
4558                 ((phy_id & 0x0F) << 4));
4559         payload.dtype_dlr_retry = cpu_to_le32((retryFlag & 0x01) |
4560                 ((linkrate & 0x0F) * 0x1000000) |
4561                 ((stp_sspsmp_sata & 0x03) * 0x10000000));
4562         payload.firstburstsize_ITNexustimeout =
4563                 cpu_to_le32(ITNT | (firstBurstSize * 0x10000));
4564         memcpy(payload.sas_addr, pm8001_dev->sas_device->sas_addr,
4565                 SAS_ADDR_SIZE);
4566         rc = pm8001_mpi_build_cmd(pm8001_ha, circularQ, opc, &payload, 0);
4567         return rc;
4568 }
4569
4570 /**
4571  * see comments on pm8001_mpi_reg_resp.
4572  */
4573 int pm8001_chip_dereg_dev_req(struct pm8001_hba_info *pm8001_ha,
4574         u32 device_id)
4575 {
4576         struct dereg_dev_req payload;
4577         u32 opc = OPC_INB_DEREG_DEV_HANDLE;
4578         int ret;
4579         struct inbound_queue_table *circularQ;
4580
4581         circularQ = &pm8001_ha->inbnd_q_tbl[0];
4582         memset(&payload, 0, sizeof(payload));
4583         payload.tag = cpu_to_le32(1);
4584         payload.device_id = cpu_to_le32(device_id);
4585         PM8001_MSG_DBG(pm8001_ha,
4586                 pm8001_printk("unregister device device_id = %d\n", device_id));
4587         ret = pm8001_mpi_build_cmd(pm8001_ha, circularQ, opc, &payload, 0);
4588         return ret;
4589 }
4590
4591 /**
4592  * pm8001_chip_phy_ctl_req - support the local phy operation
4593  * @pm8001_ha: our hba card information.
4594  * @num: the inbound queue number
4595  * @phy_id: the phy id which we wanted to operate
4596  * @phy_op:
4597  */
4598 static int pm8001_chip_phy_ctl_req(struct pm8001_hba_info *pm8001_ha,
4599         u32 phyId, u32 phy_op)
4600 {
4601         struct local_phy_ctl_req payload;
4602         struct inbound_queue_table *circularQ;
4603         int ret;
4604         u32 opc = OPC_INB_LOCAL_PHY_CONTROL;
4605         memset(&payload, 0, sizeof(payload));
4606         circularQ = &pm8001_ha->inbnd_q_tbl[0];
4607         payload.tag = cpu_to_le32(1);
4608         payload.phyop_phyid =
4609                 cpu_to_le32(((phy_op & 0xff) << 8) | (phyId & 0x0F));
4610         ret = pm8001_mpi_build_cmd(pm8001_ha, circularQ, opc, &payload, 0);
4611         return ret;
4612 }
4613
4614 static u32 pm8001_chip_is_our_interupt(struct pm8001_hba_info *pm8001_ha)
4615 {
4616         u32 value;
4617 #ifdef PM8001_USE_MSIX
4618         return 1;
4619 #endif
4620         value = pm8001_cr32(pm8001_ha, 0, MSGU_ODR);
4621         if (value)
4622                 return 1;
4623         return 0;
4624
4625 }
4626
4627 /**
4628  * pm8001_chip_isr - PM8001 isr handler.
4629  * @pm8001_ha: our hba card information.
4630  * @irq: irq number.
4631  * @stat: stat.
4632  */
4633 static irqreturn_t
4634 pm8001_chip_isr(struct pm8001_hba_info *pm8001_ha, u8 vec)
4635 {
4636         pm8001_chip_interrupt_disable(pm8001_ha, vec);
4637         process_oq(pm8001_ha, vec);
4638         pm8001_chip_interrupt_enable(pm8001_ha, vec);
4639         return IRQ_HANDLED;
4640 }
4641
4642 static int send_task_abort(struct pm8001_hba_info *pm8001_ha, u32 opc,
4643         u32 dev_id, u8 flag, u32 task_tag, u32 cmd_tag)
4644 {
4645         struct task_abort_req task_abort;
4646         struct inbound_queue_table *circularQ;
4647         int ret;
4648         circularQ = &pm8001_ha->inbnd_q_tbl[0];
4649         memset(&task_abort, 0, sizeof(task_abort));
4650         if (ABORT_SINGLE == (flag & ABORT_MASK)) {
4651                 task_abort.abort_all = 0;
4652                 task_abort.device_id = cpu_to_le32(dev_id);
4653                 task_abort.tag_to_abort = cpu_to_le32(task_tag);
4654                 task_abort.tag = cpu_to_le32(cmd_tag);
4655         } else if (ABORT_ALL == (flag & ABORT_MASK)) {
4656                 task_abort.abort_all = cpu_to_le32(1);
4657                 task_abort.device_id = cpu_to_le32(dev_id);
4658                 task_abort.tag = cpu_to_le32(cmd_tag);
4659         }
4660         ret = pm8001_mpi_build_cmd(pm8001_ha, circularQ, opc, &task_abort, 0);
4661         return ret;
4662 }
4663
4664 /**
4665  * pm8001_chip_abort_task - SAS abort task when error or exception happened.
4666  * @task: the task we wanted to aborted.
4667  * @flag: the abort flag.
4668  */
4669 int pm8001_chip_abort_task(struct pm8001_hba_info *pm8001_ha,
4670         struct pm8001_device *pm8001_dev, u8 flag, u32 task_tag, u32 cmd_tag)
4671 {
4672         u32 opc, device_id;
4673         int rc = TMF_RESP_FUNC_FAILED;
4674         PM8001_EH_DBG(pm8001_ha,
4675                 pm8001_printk("cmd_tag = %x, abort task tag = 0x%x",
4676                         cmd_tag, task_tag));
4677         if (pm8001_dev->dev_type == SAS_END_DEVICE)
4678                 opc = OPC_INB_SSP_ABORT;
4679         else if (pm8001_dev->dev_type == SAS_SATA_DEV)
4680                 opc = OPC_INB_SATA_ABORT;
4681         else
4682                 opc = OPC_INB_SMP_ABORT;/* SMP */
4683         device_id = pm8001_dev->device_id;
4684         rc = send_task_abort(pm8001_ha, opc, device_id, flag,
4685                 task_tag, cmd_tag);
4686         if (rc != TMF_RESP_FUNC_COMPLETE)
4687                 PM8001_EH_DBG(pm8001_ha, pm8001_printk("rc= %d\n", rc));
4688         return rc;
4689 }
4690
4691 /**
4692  * pm8001_chip_ssp_tm_req - built the task management command.
4693  * @pm8001_ha: our hba card information.
4694  * @ccb: the ccb information.
4695  * @tmf: task management function.
4696  */
4697 int pm8001_chip_ssp_tm_req(struct pm8001_hba_info *pm8001_ha,
4698         struct pm8001_ccb_info *ccb, struct pm8001_tmf_task *tmf)
4699 {
4700         struct sas_task *task = ccb->task;
4701         struct domain_device *dev = task->dev;
4702         struct pm8001_device *pm8001_dev = dev->lldd_dev;
4703         u32 opc = OPC_INB_SSPINITMSTART;
4704         struct inbound_queue_table *circularQ;
4705         struct ssp_ini_tm_start_req sspTMCmd;
4706         int ret;
4707
4708         memset(&sspTMCmd, 0, sizeof(sspTMCmd));
4709         sspTMCmd.device_id = cpu_to_le32(pm8001_dev->device_id);
4710         sspTMCmd.relate_tag = cpu_to_le32(tmf->tag_of_task_to_be_managed);
4711         sspTMCmd.tmf = cpu_to_le32(tmf->tmf);
4712         memcpy(sspTMCmd.lun, task->ssp_task.LUN, 8);
4713         sspTMCmd.tag = cpu_to_le32(ccb->ccb_tag);
4714         if (pm8001_ha->chip_id != chip_8001)
4715                 sspTMCmd.ds_ads_m = 0x08;
4716         circularQ = &pm8001_ha->inbnd_q_tbl[0];
4717         ret = pm8001_mpi_build_cmd(pm8001_ha, circularQ, opc, &sspTMCmd, 0);
4718         return ret;
4719 }
4720
4721 int pm8001_chip_get_nvmd_req(struct pm8001_hba_info *pm8001_ha,
4722         void *payload)
4723 {
4724         u32 opc = OPC_INB_GET_NVMD_DATA;
4725         u32 nvmd_type;
4726         int rc;
4727         u32 tag;
4728         struct pm8001_ccb_info *ccb;
4729         struct inbound_queue_table *circularQ;
4730         struct get_nvm_data_req nvmd_req;
4731         struct fw_control_ex *fw_control_context;
4732         struct pm8001_ioctl_payload *ioctl_payload = payload;
4733
4734         nvmd_type = ioctl_payload->minor_function;
4735         fw_control_context = kzalloc(sizeof(struct fw_control_ex), GFP_KERNEL);
4736         if (!fw_control_context)
4737                 return -ENOMEM;
4738         fw_control_context->usrAddr = (u8 *)ioctl_payload->func_specific;
4739         fw_control_context->len = ioctl_payload->length;
4740         circularQ = &pm8001_ha->inbnd_q_tbl[0];
4741         memset(&nvmd_req, 0, sizeof(nvmd_req));
4742         rc = pm8001_tag_alloc(pm8001_ha, &tag);
4743         if (rc) {
4744                 kfree(fw_control_context);
4745                 return rc;
4746         }
4747         ccb = &pm8001_ha->ccb_info[tag];
4748         ccb->ccb_tag = tag;
4749         ccb->fw_control_context = fw_control_context;
4750         nvmd_req.tag = cpu_to_le32(tag);
4751
4752         switch (nvmd_type) {
4753         case TWI_DEVICE: {
4754                 u32 twi_addr, twi_page_size;
4755                 twi_addr = 0xa8;
4756                 twi_page_size = 2;
4757
4758                 nvmd_req.len_ir_vpdd = cpu_to_le32(IPMode | twi_addr << 16 |
4759                         twi_page_size << 8 | TWI_DEVICE);
4760                 nvmd_req.resp_len = cpu_to_le32(ioctl_payload->length);
4761                 nvmd_req.resp_addr_hi =
4762                     cpu_to_le32(pm8001_ha->memoryMap.region[NVMD].phys_addr_hi);
4763                 nvmd_req.resp_addr_lo =
4764                     cpu_to_le32(pm8001_ha->memoryMap.region[NVMD].phys_addr_lo);
4765                 break;
4766         }
4767         case C_SEEPROM: {
4768                 nvmd_req.len_ir_vpdd = cpu_to_le32(IPMode | C_SEEPROM);
4769                 nvmd_req.resp_len = cpu_to_le32(ioctl_payload->length);
4770                 nvmd_req.resp_addr_hi =
4771                     cpu_to_le32(pm8001_ha->memoryMap.region[NVMD].phys_addr_hi);
4772                 nvmd_req.resp_addr_lo =
4773                     cpu_to_le32(pm8001_ha->memoryMap.region[NVMD].phys_addr_lo);
4774                 break;
4775         }
4776         case VPD_FLASH: {
4777                 nvmd_req.len_ir_vpdd = cpu_to_le32(IPMode | VPD_FLASH);
4778                 nvmd_req.resp_len = cpu_to_le32(ioctl_payload->length);
4779                 nvmd_req.resp_addr_hi =
4780                     cpu_to_le32(pm8001_ha->memoryMap.region[NVMD].phys_addr_hi);
4781                 nvmd_req.resp_addr_lo =
4782                     cpu_to_le32(pm8001_ha->memoryMap.region[NVMD].phys_addr_lo);
4783                 break;
4784         }
4785         case EXPAN_ROM: {
4786                 nvmd_req.len_ir_vpdd = cpu_to_le32(IPMode | EXPAN_ROM);
4787                 nvmd_req.resp_len = cpu_to_le32(ioctl_payload->length);
4788                 nvmd_req.resp_addr_hi =
4789                     cpu_to_le32(pm8001_ha->memoryMap.region[NVMD].phys_addr_hi);
4790                 nvmd_req.resp_addr_lo =
4791                     cpu_to_le32(pm8001_ha->memoryMap.region[NVMD].phys_addr_lo);
4792                 break;
4793         }
4794         case IOP_RDUMP: {
4795                 nvmd_req.len_ir_vpdd = cpu_to_le32(IPMode | IOP_RDUMP);
4796                 nvmd_req.resp_len = cpu_to_le32(ioctl_payload->length);
4797                 nvmd_req.vpd_offset = cpu_to_le32(ioctl_payload->offset);
4798                 nvmd_req.resp_addr_hi =
4799                 cpu_to_le32(pm8001_ha->memoryMap.region[NVMD].phys_addr_hi);
4800                 nvmd_req.resp_addr_lo =
4801                 cpu_to_le32(pm8001_ha->memoryMap.region[NVMD].phys_addr_lo);
4802                 break;
4803         }
4804         default:
4805                 break;
4806         }
4807         rc = pm8001_mpi_build_cmd(pm8001_ha, circularQ, opc, &nvmd_req, 0);
4808         if (rc) {
4809                 kfree(fw_control_context);
4810                 pm8001_tag_free(pm8001_ha, tag);
4811         }
4812         return rc;
4813 }
4814
4815 int pm8001_chip_set_nvmd_req(struct pm8001_hba_info *pm8001_ha,
4816         void *payload)
4817 {
4818         u32 opc = OPC_INB_SET_NVMD_DATA;
4819         u32 nvmd_type;
4820         int rc;
4821         u32 tag;
4822         struct pm8001_ccb_info *ccb;
4823         struct inbound_queue_table *circularQ;
4824         struct set_nvm_data_req nvmd_req;
4825         struct fw_control_ex *fw_control_context;
4826         struct pm8001_ioctl_payload *ioctl_payload = payload;
4827
4828         nvmd_type = ioctl_payload->minor_function;
4829         fw_control_context = kzalloc(sizeof(struct fw_control_ex), GFP_KERNEL);
4830         if (!fw_control_context)
4831                 return -ENOMEM;
4832         circularQ = &pm8001_ha->inbnd_q_tbl[0];
4833         memcpy(pm8001_ha->memoryMap.region[NVMD].virt_ptr,
4834                 &ioctl_payload->func_specific,
4835                 ioctl_payload->length);
4836         memset(&nvmd_req, 0, sizeof(nvmd_req));
4837         rc = pm8001_tag_alloc(pm8001_ha, &tag);
4838         if (rc) {
4839                 kfree(fw_control_context);
4840                 return -EBUSY;
4841         }
4842         ccb = &pm8001_ha->ccb_info[tag];
4843         ccb->fw_control_context = fw_control_context;
4844         ccb->ccb_tag = tag;
4845         nvmd_req.tag = cpu_to_le32(tag);
4846         switch (nvmd_type) {
4847         case TWI_DEVICE: {
4848                 u32 twi_addr, twi_page_size;
4849                 twi_addr = 0xa8;
4850                 twi_page_size = 2;
4851                 nvmd_req.reserved[0] = cpu_to_le32(0xFEDCBA98);
4852                 nvmd_req.len_ir_vpdd = cpu_to_le32(IPMode | twi_addr << 16 |
4853                         twi_page_size << 8 | TWI_DEVICE);
4854                 nvmd_req.resp_len = cpu_to_le32(ioctl_payload->length);
4855                 nvmd_req.resp_addr_hi =
4856                     cpu_to_le32(pm8001_ha->memoryMap.region[NVMD].phys_addr_hi);
4857                 nvmd_req.resp_addr_lo =
4858                     cpu_to_le32(pm8001_ha->memoryMap.region[NVMD].phys_addr_lo);
4859                 break;
4860         }
4861         case C_SEEPROM:
4862                 nvmd_req.len_ir_vpdd = cpu_to_le32(IPMode | C_SEEPROM);
4863                 nvmd_req.resp_len = cpu_to_le32(ioctl_payload->length);
4864                 nvmd_req.reserved[0] = cpu_to_le32(0xFEDCBA98);
4865                 nvmd_req.resp_addr_hi =
4866                     cpu_to_le32(pm8001_ha->memoryMap.region[NVMD].phys_addr_hi);
4867                 nvmd_req.resp_addr_lo =
4868                     cpu_to_le32(pm8001_ha->memoryMap.region[NVMD].phys_addr_lo);
4869                 break;
4870         case VPD_FLASH:
4871                 nvmd_req.len_ir_vpdd = cpu_to_le32(IPMode | VPD_FLASH);
4872                 nvmd_req.resp_len = cpu_to_le32(ioctl_payload->length);
4873                 nvmd_req.reserved[0] = cpu_to_le32(0xFEDCBA98);
4874                 nvmd_req.resp_addr_hi =
4875                     cpu_to_le32(pm8001_ha->memoryMap.region[NVMD].phys_addr_hi);
4876                 nvmd_req.resp_addr_lo =
4877                     cpu_to_le32(pm8001_ha->memoryMap.region[NVMD].phys_addr_lo);
4878                 break;
4879         case EXPAN_ROM:
4880                 nvmd_req.len_ir_vpdd = cpu_to_le32(IPMode | EXPAN_ROM);
4881                 nvmd_req.resp_len = cpu_to_le32(ioctl_payload->length);
4882                 nvmd_req.reserved[0] = cpu_to_le32(0xFEDCBA98);
4883                 nvmd_req.resp_addr_hi =
4884                     cpu_to_le32(pm8001_ha->memoryMap.region[NVMD].phys_addr_hi);
4885                 nvmd_req.resp_addr_lo =
4886                     cpu_to_le32(pm8001_ha->memoryMap.region[NVMD].phys_addr_lo);
4887                 break;
4888         default:
4889                 break;
4890         }
4891         rc = pm8001_mpi_build_cmd(pm8001_ha, circularQ, opc, &nvmd_req, 0);
4892         if (rc) {
4893                 kfree(fw_control_context);
4894                 pm8001_tag_free(pm8001_ha, tag);
4895         }
4896         return rc;
4897 }
4898
4899 /**
4900  * pm8001_chip_fw_flash_update_build - support the firmware update operation
4901  * @pm8001_ha: our hba card information.
4902  * @fw_flash_updata_info: firmware flash update param
4903  */
4904 int
4905 pm8001_chip_fw_flash_update_build(struct pm8001_hba_info *pm8001_ha,
4906         void *fw_flash_updata_info, u32 tag)
4907 {
4908         struct fw_flash_Update_req payload;
4909         struct fw_flash_updata_info *info;
4910         struct inbound_queue_table *circularQ;
4911         int ret;
4912         u32 opc = OPC_INB_FW_FLASH_UPDATE;
4913
4914         memset(&payload, 0, sizeof(struct fw_flash_Update_req));
4915         circularQ = &pm8001_ha->inbnd_q_tbl[0];
4916         info = fw_flash_updata_info;
4917         payload.tag = cpu_to_le32(tag);
4918         payload.cur_image_len = cpu_to_le32(info->cur_image_len);
4919         payload.cur_image_offset = cpu_to_le32(info->cur_image_offset);
4920         payload.total_image_len = cpu_to_le32(info->total_image_len);
4921         payload.len = info->sgl.im_len.len ;
4922         payload.sgl_addr_lo =
4923                 cpu_to_le32(lower_32_bits(le64_to_cpu(info->sgl.addr)));
4924         payload.sgl_addr_hi =
4925                 cpu_to_le32(upper_32_bits(le64_to_cpu(info->sgl.addr)));
4926         ret = pm8001_mpi_build_cmd(pm8001_ha, circularQ, opc, &payload, 0);
4927         return ret;
4928 }
4929
4930 int
4931 pm8001_chip_fw_flash_update_req(struct pm8001_hba_info *pm8001_ha,
4932         void *payload)
4933 {
4934         struct fw_flash_updata_info flash_update_info;
4935         struct fw_control_info *fw_control;
4936         struct fw_control_ex *fw_control_context;
4937         int rc;
4938         u32 tag;
4939         struct pm8001_ccb_info *ccb;
4940         void *buffer = pm8001_ha->memoryMap.region[FW_FLASH].virt_ptr;
4941         dma_addr_t phys_addr = pm8001_ha->memoryMap.region[FW_FLASH].phys_addr;
4942         struct pm8001_ioctl_payload *ioctl_payload = payload;
4943
4944         fw_control_context = kzalloc(sizeof(struct fw_control_ex), GFP_KERNEL);
4945         if (!fw_control_context)
4946                 return -ENOMEM;
4947         fw_control = (struct fw_control_info *)&ioctl_payload->func_specific;
4948         memcpy(buffer, fw_control->buffer, fw_control->len);
4949         flash_update_info.sgl.addr = cpu_to_le64(phys_addr);
4950         flash_update_info.sgl.im_len.len = cpu_to_le32(fw_control->len);
4951         flash_update_info.sgl.im_len.e = 0;
4952         flash_update_info.cur_image_offset = fw_control->offset;
4953         flash_update_info.cur_image_len = fw_control->len;
4954         flash_update_info.total_image_len = fw_control->size;
4955         fw_control_context->fw_control = fw_control;
4956         fw_control_context->virtAddr = buffer;
4957         fw_control_context->phys_addr = phys_addr;
4958         fw_control_context->len = fw_control->len;
4959         rc = pm8001_tag_alloc(pm8001_ha, &tag);
4960         if (rc) {
4961                 kfree(fw_control_context);
4962                 return -EBUSY;
4963         }
4964         ccb = &pm8001_ha->ccb_info[tag];
4965         ccb->fw_control_context = fw_control_context;
4966         ccb->ccb_tag = tag;
4967         rc = pm8001_chip_fw_flash_update_build(pm8001_ha, &flash_update_info,
4968                 tag);
4969         return rc;
4970 }
4971
4972 ssize_t
4973 pm8001_get_gsm_dump(struct device *cdev, u32 length, char *buf)
4974 {
4975         u32 value, rem, offset = 0, bar = 0;
4976         u32 index, work_offset, dw_length;
4977         u32 shift_value, gsm_base, gsm_dump_offset;
4978         char *direct_data;
4979         struct Scsi_Host *shost = class_to_shost(cdev);
4980         struct sas_ha_struct *sha = SHOST_TO_SAS_HA(shost);
4981         struct pm8001_hba_info *pm8001_ha = sha->lldd_ha;
4982
4983         direct_data = buf;
4984         gsm_dump_offset = pm8001_ha->fatal_forensic_shift_offset;
4985
4986         /* check max is 1 Mbytes */
4987         if ((length > 0x100000) || (gsm_dump_offset & 3) ||
4988                 ((gsm_dump_offset + length) > 0x1000000))
4989                         return -EINVAL;
4990
4991         if (pm8001_ha->chip_id == chip_8001)
4992                 bar = 2;
4993         else
4994                 bar = 1;
4995
4996         work_offset = gsm_dump_offset & 0xFFFF0000;
4997         offset = gsm_dump_offset & 0x0000FFFF;
4998         gsm_dump_offset = work_offset;
4999         /* adjust length to dword boundary */
5000         rem = length & 3;
5001         dw_length = length >> 2;
5002
5003         for (index = 0; index < dw_length; index++) {
5004                 if ((work_offset + offset) & 0xFFFF0000) {
5005                         if (pm8001_ha->chip_id == chip_8001)
5006                                 shift_value = ((gsm_dump_offset + offset) &
5007                                                 SHIFT_REG_64K_MASK);
5008                         else
5009                                 shift_value = (((gsm_dump_offset + offset) &
5010                                                 SHIFT_REG_64K_MASK) >>
5011                                                 SHIFT_REG_BIT_SHIFT);
5012
5013                         if (pm8001_ha->chip_id == chip_8001) {
5014                                 gsm_base = GSM_BASE;
5015                                 if (-1 == pm8001_bar4_shift(pm8001_ha,
5016                                                 (gsm_base + shift_value)))
5017                                         return -EIO;
5018                         } else {
5019                                 gsm_base = 0;
5020                                 if (-1 == pm80xx_bar4_shift(pm8001_ha,
5021                                                 (gsm_base + shift_value)))
5022                                         return -EIO;
5023                         }
5024                         gsm_dump_offset = (gsm_dump_offset + offset) &
5025                                                 0xFFFF0000;
5026                         work_offset = 0;
5027                         offset = offset & 0x0000FFFF;
5028                 }
5029                 value = pm8001_cr32(pm8001_ha, bar, (work_offset + offset) &
5030                                                 0x0000FFFF);
5031                 direct_data += sprintf(direct_data, "%08x ", value);
5032                 offset += 4;
5033         }
5034         if (rem != 0) {
5035                 value = pm8001_cr32(pm8001_ha, bar, (work_offset + offset) &
5036                                                 0x0000FFFF);
5037                 /* xfr for non_dw */
5038                 direct_data += sprintf(direct_data, "%08x ", value);
5039         }
5040         /* Shift back to BAR4 original address */
5041         if (-1 == pm8001_bar4_shift(pm8001_ha, 0))
5042                         return -EIO;
5043         pm8001_ha->fatal_forensic_shift_offset += 1024;
5044
5045         if (pm8001_ha->fatal_forensic_shift_offset >= 0x100000)
5046                 pm8001_ha->fatal_forensic_shift_offset = 0;
5047         return direct_data - buf;
5048 }
5049
5050 int
5051 pm8001_chip_set_dev_state_req(struct pm8001_hba_info *pm8001_ha,
5052         struct pm8001_device *pm8001_dev, u32 state)
5053 {
5054         struct set_dev_state_req payload;
5055         struct inbound_queue_table *circularQ;
5056         struct pm8001_ccb_info *ccb;
5057         int rc;
5058         u32 tag;
5059         u32 opc = OPC_INB_SET_DEVICE_STATE;
5060         memset(&payload, 0, sizeof(payload));
5061         rc = pm8001_tag_alloc(pm8001_ha, &tag);
5062         if (rc)
5063                 return -1;
5064         ccb = &pm8001_ha->ccb_info[tag];
5065         ccb->ccb_tag = tag;
5066         ccb->device = pm8001_dev;
5067         circularQ = &pm8001_ha->inbnd_q_tbl[0];
5068         payload.tag = cpu_to_le32(tag);
5069         payload.device_id = cpu_to_le32(pm8001_dev->device_id);
5070         payload.nds = cpu_to_le32(state);
5071         rc = pm8001_mpi_build_cmd(pm8001_ha, circularQ, opc, &payload, 0);
5072         return rc;
5073
5074 }
5075
5076 static int
5077 pm8001_chip_sas_re_initialization(struct pm8001_hba_info *pm8001_ha)
5078 {
5079         struct sas_re_initialization_req payload;
5080         struct inbound_queue_table *circularQ;
5081         struct pm8001_ccb_info *ccb;
5082         int rc;
5083         u32 tag;
5084         u32 opc = OPC_INB_SAS_RE_INITIALIZE;
5085         memset(&payload, 0, sizeof(payload));
5086         rc = pm8001_tag_alloc(pm8001_ha, &tag);
5087         if (rc)
5088                 return -ENOMEM;
5089         ccb = &pm8001_ha->ccb_info[tag];
5090         ccb->ccb_tag = tag;
5091         circularQ = &pm8001_ha->inbnd_q_tbl[0];
5092         payload.tag = cpu_to_le32(tag);
5093         payload.SSAHOLT = cpu_to_le32(0xd << 25);
5094         payload.sata_hol_tmo = cpu_to_le32(80);
5095         payload.open_reject_cmdretries_data_retries = cpu_to_le32(0xff00ff);
5096         rc = pm8001_mpi_build_cmd(pm8001_ha, circularQ, opc, &payload, 0);
5097         if (rc)
5098                 pm8001_tag_free(pm8001_ha, tag);
5099         return rc;
5100
5101 }
5102
5103 const struct pm8001_dispatch pm8001_8001_dispatch = {
5104         .name                   = "pmc8001",
5105         .chip_init              = pm8001_chip_init,
5106         .chip_soft_rst          = pm8001_chip_soft_rst,
5107         .chip_rst               = pm8001_hw_chip_rst,
5108         .chip_iounmap           = pm8001_chip_iounmap,
5109         .isr                    = pm8001_chip_isr,
5110         .is_our_interupt        = pm8001_chip_is_our_interupt,
5111         .isr_process_oq         = process_oq,
5112         .interrupt_enable       = pm8001_chip_interrupt_enable,
5113         .interrupt_disable      = pm8001_chip_interrupt_disable,
5114         .make_prd               = pm8001_chip_make_sg,
5115         .smp_req                = pm8001_chip_smp_req,
5116         .ssp_io_req             = pm8001_chip_ssp_io_req,
5117         .sata_req               = pm8001_chip_sata_req,
5118         .phy_start_req          = pm8001_chip_phy_start_req,
5119         .phy_stop_req           = pm8001_chip_phy_stop_req,
5120         .reg_dev_req            = pm8001_chip_reg_dev_req,
5121         .dereg_dev_req          = pm8001_chip_dereg_dev_req,
5122         .phy_ctl_req            = pm8001_chip_phy_ctl_req,
5123         .task_abort             = pm8001_chip_abort_task,
5124         .ssp_tm_req             = pm8001_chip_ssp_tm_req,
5125         .get_nvmd_req           = pm8001_chip_get_nvmd_req,
5126         .set_nvmd_req           = pm8001_chip_set_nvmd_req,
5127         .fw_flash_update_req    = pm8001_chip_fw_flash_update_req,
5128         .set_dev_state_req      = pm8001_chip_set_dev_state_req,
5129         .sas_re_init_req        = pm8001_chip_sas_re_initialization,
5130 };