kernel/drivers/phy/phy-twl4030-usb.c

   1 /*
   2  * twl4030_usb - TWL4030 USB transceiver, talking to OMAP OTG controller
   3  *
   4  * Copyright (C) 2004-2007 Texas Instruments
   5  * Copyright (C) 2008 Nokia Corporation
   6  * Contact: Felipe Balbi <felipe.balbi@nokia.com>
   7  *
   8  * This program is free software; you can redistribute it and/or modify
   9  * it under the terms of the GNU General Public License as published by
  10  * the Free Software Foundation; either version 2 of the License, or
  11  * (at your option) any later version.
  12  *
  13  * This program is distributed in the hope that it will be useful,
  14  * but WITHOUT ANY WARRANTY; without even the implied warranty of
  15  * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  16  * GNU General Public License for more details.
  17  *
  18  * You should have received a copy of the GNU General Public License
  19  * along with this program; if not, write to the Free Software
  20  * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
  21  *
  22  * Current status:
  23  *      - HS USB ULPI mode works.
  24  *      - 3-pin mode support may be added in future.
  25  */
  26
  27 #include <linux/module.h>
  28 #include <linux/init.h>
  29 #include <linux/interrupt.h>
  30 #include <linux/platform_device.h>
  31 #include <linux/workqueue.h>
  32 #include <linux/io.h>
  33 #include <linux/delay.h>
  34 #include <linux/usb/otg.h>
  35 #include <linux/phy/phy.h>
  36 #include <linux/pm_runtime.h>
  37 #include <linux/usb/musb-omap.h>
  38 #include <linux/usb/ulpi.h>
  39 #include <linux/i2c/twl.h>
  40 #include <linux/regulator/consumer.h>
  41 #include <linux/err.h>
  42 #include <linux/slab.h>
  43
  44 /* Register defines */
  45
  46 #define MCPC_CTRL                       0x30
  47 #define MCPC_CTRL_RTSOL                 (1 << 7)
  48 #define MCPC_CTRL_EXTSWR                (1 << 6)
  49 #define MCPC_CTRL_EXTSWC                (1 << 5)
  50 #define MCPC_CTRL_VOICESW               (1 << 4)
  51 #define MCPC_CTRL_OUT64K                (1 << 3)
  52 #define MCPC_CTRL_RTSCTSSW              (1 << 2)
  53 #define MCPC_CTRL_HS_UART               (1 << 0)
  54
  55 #define MCPC_IO_CTRL                    0x33
  56 #define MCPC_IO_CTRL_MICBIASEN          (1 << 5)
  57 #define MCPC_IO_CTRL_CTS_NPU            (1 << 4)
  58 #define MCPC_IO_CTRL_RXD_PU             (1 << 3)
  59 #define MCPC_IO_CTRL_TXDTYP             (1 << 2)
  60 #define MCPC_IO_CTRL_CTSTYP             (1 << 1)
  61 #define MCPC_IO_CTRL_RTSTYP             (1 << 0)
  62
  63 #define MCPC_CTRL2                      0x36
  64 #define MCPC_CTRL2_MCPC_CK_EN           (1 << 0)
  65
  66 #define OTHER_FUNC_CTRL                 0x80
  67 #define OTHER_FUNC_CTRL_BDIS_ACON_EN    (1 << 4)
  68 #define OTHER_FUNC_CTRL_FIVEWIRE_MODE   (1 << 2)
  69
  70 #define OTHER_IFC_CTRL                  0x83
  71 #define OTHER_IFC_CTRL_OE_INT_EN        (1 << 6)
  72 #define OTHER_IFC_CTRL_CEA2011_MODE     (1 << 5)
  73 #define OTHER_IFC_CTRL_FSLSSERIALMODE_4PIN      (1 << 4)
  74 #define OTHER_IFC_CTRL_HIZ_ULPI_60MHZ_OUT       (1 << 3)
  75 #define OTHER_IFC_CTRL_HIZ_ULPI         (1 << 2)
  76 #define OTHER_IFC_CTRL_ALT_INT_REROUTE  (1 << 0)
  77
  78 #define OTHER_INT_EN_RISE               0x86
  79 #define OTHER_INT_EN_FALL               0x89
  80 #define OTHER_INT_STS                   0x8C
  81 #define OTHER_INT_LATCH                 0x8D
  82 #define OTHER_INT_VB_SESS_VLD           (1 << 7)
  83 #define OTHER_INT_DM_HI                 (1 << 6) /* not valid for "latch" reg */
  84 #define OTHER_INT_DP_HI                 (1 << 5) /* not valid for "latch" reg */
  85 #define OTHER_INT_BDIS_ACON             (1 << 3) /* not valid for "fall" regs */
  86 #define OTHER_INT_MANU                  (1 << 1)
  87 #define OTHER_INT_ABNORMAL_STRESS       (1 << 0)
  88
  89 #define ID_STATUS                       0x96
  90 #define ID_RES_FLOAT                    (1 << 4)
  91 #define ID_RES_440K                     (1 << 3)
  92 #define ID_RES_200K                     (1 << 2)
  93 #define ID_RES_102K                     (1 << 1)
  94 #define ID_RES_GND                      (1 << 0)
  95
  96 #define POWER_CTRL                      0xAC
  97 #define POWER_CTRL_OTG_ENAB             (1 << 5)
  98
  99 #define OTHER_IFC_CTRL2                 0xAF
 100 #define OTHER_IFC_CTRL2_ULPI_STP_LOW    (1 << 4)
 101 #define OTHER_IFC_CTRL2_ULPI_TXEN_POL   (1 << 3)
 102 #define OTHER_IFC_CTRL2_ULPI_4PIN_2430  (1 << 2)
 103 #define OTHER_IFC_CTRL2_USB_INT_OUTSEL_MASK     (3 << 0) /* bits 0 and 1 */
 104 #define OTHER_IFC_CTRL2_USB_INT_OUTSEL_INT1N    (0 << 0)
 105 #define OTHER_IFC_CTRL2_USB_INT_OUTSEL_INT2N    (1 << 0)
 106
 107 #define REG_CTRL_EN                     0xB2
 108 #define REG_CTRL_ERROR                  0xB5
 109 #define ULPI_I2C_CONFLICT_INTEN         (1 << 0)
 110
 111 #define OTHER_FUNC_CTRL2                0xB8
 112 #define OTHER_FUNC_CTRL2_VBAT_TIMER_EN  (1 << 0)
 113
 114 /* following registers do not have separate _clr and _set registers */
 115 #define VBUS_DEBOUNCE                   0xC0
 116 #define ID_DEBOUNCE                     0xC1
 117 #define VBAT_TIMER                      0xD3
 118 #define PHY_PWR_CTRL                    0xFD
 119 #define PHY_PWR_PHYPWD                  (1 << 0)
 120 #define PHY_CLK_CTRL                    0xFE
 121 #define PHY_CLK_CTRL_CLOCKGATING_EN     (1 << 2)
 122 #define PHY_CLK_CTRL_CLK32K_EN          (1 << 1)
 123 #define REQ_PHY_DPLL_CLK                (1 << 0)
 124 #define PHY_CLK_CTRL_STS                0xFF
 125 #define PHY_DPLL_CLK                    (1 << 0)
 126
 127 /* In module TWL_MODULE_PM_MASTER */
 128 #define STS_HW_CONDITIONS               0x0F
 129
 130 /* In module TWL_MODULE_PM_RECEIVER */
 131 #define VUSB_DEDICATED1                 0x7D
 132 #define VUSB_DEDICATED2                 0x7E
 133 #define VUSB1V5_DEV_GRP                 0x71
 134 #define VUSB1V5_TYPE                    0x72
 135 #define VUSB1V5_REMAP                   0x73
 136 #define VUSB1V8_DEV_GRP                 0x74
 137 #define VUSB1V8_TYPE                    0x75
 138 #define VUSB1V8_REMAP                   0x76
 139 #define VUSB3V1_DEV_GRP                 0x77
 140 #define VUSB3V1_TYPE                    0x78
 141 #define VUSB3V1_REMAP                   0x79
 142
 143 /* In module TWL4030_MODULE_INTBR */
 144 #define PMBR1                           0x0D
 145 #define GPIO_USB_4PIN_ULPI_2430C        (3 << 0)
 146
 147 /*
 148  * If VBUS is valid or ID is ground, then we know a
 149  * cable is present and we need to be runtime-enabled
 150  */
 151 static inline bool cable_present(enum omap_musb_vbus_id_status stat)
 152 {
 153         return stat == OMAP_MUSB_VBUS_VALID ||
 154                 stat == OMAP_MUSB_ID_GROUND;
 155 }
 156
 157 struct twl4030_usb {
 158         struct usb_phy          phy;
 159         struct device           *dev;
 160
 161         /* TWL4030 internal USB regulator supplies */
 162         struct regulator        *usb1v5;
 163         struct regulator        *usb1v8;
 164         struct regulator        *usb3v1;
 165
 166         /* for vbus reporting with irqs disabled */
 167         struct mutex            lock;
 168
 169         /* pin configuration */
 170         enum twl4030_usb_mode   usb_mode;
 171
 172         int                     irq;
 173         enum omap_musb_vbus_id_status linkstat;
 174         bool                    vbus_supplied;
 175
 176         struct delayed_work     id_workaround_work;
 177 };
 178
 179 /* internal define on top of container_of */
 180 #define phy_to_twl(x)           container_of((x), struct twl4030_usb, phy)
 181
 182 /*-------------------------------------------------------------------------*/
 183
 184 static int twl4030_i2c_write_u8_verify(struct twl4030_usb *twl,
 185                 u8 module, u8 data, u8 address)
 186 {
 187         u8 check;
 188
 189         if ((twl_i2c_write_u8(module, data, address) >= 0) &&
 190             (twl_i2c_read_u8(module, &check, address) >= 0) &&
 191                                                 (check == data))
 192                 return 0;
 193         dev_dbg(twl->dev, "Write%d[%d,0x%x] wrote %02x but read %02x\n",
 194                         1, module, address, check, data);
 195
 196         /* Failed once: Try again */
 197         if ((twl_i2c_write_u8(module, data, address) >= 0) &&
 198             (twl_i2c_read_u8(module, &check, address) >= 0) &&
 199                                                 (check == data))
 200                 return 0;
 201         dev_dbg(twl->dev, "Write%d[%d,0x%x] wrote %02x but read %02x\n",
 202                         2, module, address, check, data);
 203
 204         /* Failed again: Return error */
 205         return -EBUSY;
 206 }
 207
 208 #define twl4030_usb_write_verify(twl, address, data)    \
 209         twl4030_i2c_write_u8_verify(twl, TWL_MODULE_USB, (data), (address))
 210
 211 static inline int twl4030_usb_write(struct twl4030_usb *twl,
 212                 u8 address, u8 data)
 213 {
 214         int ret = 0;
 215
 216         ret = twl_i2c_write_u8(TWL_MODULE_USB, data, address);
 217         if (ret < 0)
 218                 dev_dbg(twl->dev,
 219                         "TWL4030:USB:Write[0x%x] Error %d\n", address, ret);
 220         return ret;
 221 }
 222
 223 static inline int twl4030_readb(struct twl4030_usb *twl, u8 module, u8 address)
 224 {
 225         u8 data;
 226         int ret = 0;
 227
 228         ret = twl_i2c_read_u8(module, &data, address);
 229         if (ret >= 0)
 230                 ret = data;
 231         else
 232                 dev_dbg(twl->dev,
 233                         "TWL4030:readb[0x%x,0x%x] Error %d\n",
 234                                         module, address, ret);
 235
 236         return ret;
 237 }
 238
 239 static inline int twl4030_usb_read(struct twl4030_usb *twl, u8 address)
 240 {
 241         return twl4030_readb(twl, TWL_MODULE_USB, address);
 242 }
 243
 244 /*-------------------------------------------------------------------------*/
 245
 246 static inline int
 247 twl4030_usb_set_bits(struct twl4030_usb *twl, u8 reg, u8 bits)
 248 {
 249         return twl4030_usb_write(twl, ULPI_SET(reg), bits);
 250 }
 251
 252 static inline int
 253 twl4030_usb_clear_bits(struct twl4030_usb *twl, u8 reg, u8 bits)
 254 {
 255         return twl4030_usb_write(twl, ULPI_CLR(reg), bits);
 256 }
 257
 258 /*-------------------------------------------------------------------------*/
 259
 260 static bool twl4030_is_driving_vbus(struct twl4030_usb *twl)
 261 {
 262         int ret;
 263
 264         ret = twl4030_usb_read(twl, PHY_CLK_CTRL_STS);
 265         if (ret < 0 || !(ret & PHY_DPLL_CLK))
 266                 /*
 267                  * if clocks are off, registers are not updated,
 268                  * but we can assume we don't drive VBUS in this case
 269                  */
 270                 return false;
 271
 272         ret = twl4030_usb_read(twl, ULPI_OTG_CTRL);
 273         if (ret < 0)
 274                 return false;
 275
 276         return (ret & (ULPI_OTG_DRVVBUS | ULPI_OTG_CHRGVBUS)) ? true : false;
 277 }
 278
 279 static enum omap_musb_vbus_id_status
 280         twl4030_usb_linkstat(struct twl4030_usb *twl)
 281 {
 282         int     status;
 283         enum omap_musb_vbus_id_status linkstat = OMAP_MUSB_UNKNOWN;
 284
 285         twl->vbus_supplied = false;
 286
 287         /*
 288          * For ID/VBUS sensing, see manual section 15.4.8 ...
 289          * except when using only battery backup power, two
 290          * comparators produce VBUS_PRES and ID_PRES signals,
 291          * which don't match docs elsewhere.  But ... BIT(7)
 292          * and BIT(2) of STS_HW_CONDITIONS, respectively, do
 293          * seem to match up.  If either is true the USB_PRES
 294          * signal is active, the OTG module is activated, and
 295          * its interrupt may be raised (may wake the system).
 296          */
 297         status = twl4030_readb(twl, TWL_MODULE_PM_MASTER, STS_HW_CONDITIONS);
 298         if (status < 0)
 299                 dev_err(twl->dev, "USB link status err %d\n", status);
 300         else if (status & (BIT(7) | BIT(2))) {
 301                 if (status & BIT(7)) {
 302                         if (twl4030_is_driving_vbus(twl))
 303                                 status &= ~BIT(7);
 304                         else
 305                                 twl->vbus_supplied = true;
 306                 }
 307
 308                 if (status & BIT(2))
 309                         linkstat = OMAP_MUSB_ID_GROUND;
 310                 else if (status & BIT(7))
 311                         linkstat = OMAP_MUSB_VBUS_VALID;
 312                 else
 313                         linkstat = OMAP_MUSB_VBUS_OFF;
 314         } else {
 315                 if (twl->linkstat != OMAP_MUSB_UNKNOWN)
 316                         linkstat = OMAP_MUSB_VBUS_OFF;
 317         }
 318
 319         dev_dbg(twl->dev, "HW_CONDITIONS 0x%02x/%d; link %d\n",
 320                         status, status, linkstat);
 321
 322         /* REVISIT this assumes host and peripheral controllers
 323          * are registered, and that both are active...
 324          */
 325
 326         return linkstat;
 327 }
 328
 329 static void twl4030_usb_set_mode(struct twl4030_usb *twl, int mode)
 330 {
 331         twl->usb_mode = mode;
 332
 333         switch (mode) {
 334         case T2_USB_MODE_ULPI:
 335                 twl4030_usb_clear_bits(twl, ULPI_IFC_CTRL,
 336                                         ULPI_IFC_CTRL_CARKITMODE);
 337                 twl4030_usb_set_bits(twl, POWER_CTRL, POWER_CTRL_OTG_ENAB);
 338                 twl4030_usb_clear_bits(twl, ULPI_FUNC_CTRL,
 339                                         ULPI_FUNC_CTRL_XCVRSEL_MASK |
 340                                         ULPI_FUNC_CTRL_OPMODE_MASK);
 341                 break;
 342         case -1:
 343                 /* FIXME: power on defaults */
 344                 break;
 345         default:
 346                 dev_err(twl->dev, "unsupported T2 transceiver mode %d\n",
 347                                 mode);
 348                 break;
 349         }
 350 }
 351
 352 static void twl4030_i2c_access(struct twl4030_usb *twl, int on)
 353 {
 354         unsigned long timeout;
 355         int val = twl4030_usb_read(twl, PHY_CLK_CTRL);
 356
 357         if (val >= 0) {
 358                 if (on) {
 359                         /* enable DPLL to access PHY registers over I2C */
 360                         val |= REQ_PHY_DPLL_CLK;
 361                         WARN_ON(twl4030_usb_write_verify(twl, PHY_CLK_CTRL,
 362                                                 (u8)val) < 0);
 363
 364                         timeout = jiffies + HZ;
 365                         while (!(twl4030_usb_read(twl, PHY_CLK_CTRL_STS) &
 366                                                         PHY_DPLL_CLK)
 367                                 && time_before(jiffies, timeout))
 368                                         udelay(10);
 369                         if (!(twl4030_usb_read(twl, PHY_CLK_CTRL_STS) &
 370                                                         PHY_DPLL_CLK))
 371                                 dev_err(twl->dev, "Timeout setting T2 HSUSB "
 372                                                 "PHY DPLL clock\n");
 373                 } else {
 374                         /* let ULPI control the DPLL clock */
 375                         val &= ~REQ_PHY_DPLL_CLK;
 376                         WARN_ON(twl4030_usb_write_verify(twl, PHY_CLK_CTRL,
 377                                                 (u8)val) < 0);
 378                 }
 379         }
 380 }
 381
 382 static void __twl4030_phy_power(struct twl4030_usb *twl, int on)
 383 {
 384         u8 pwr = twl4030_usb_read(twl, PHY_PWR_CTRL);
 385
 386         if (on)
 387                 pwr &= ~PHY_PWR_PHYPWD;
 388         else
 389                 pwr |= PHY_PWR_PHYPWD;
 390
 391         WARN_ON(twl4030_usb_write_verify(twl, PHY_PWR_CTRL, pwr) < 0);
 392 }
 393
 394 static int twl4030_usb_runtime_suspend(struct device *dev)
 395 {
 396         struct twl4030_usb *twl = dev_get_drvdata(dev);
 397
 398         dev_dbg(twl->dev, "%s\n", __func__);
 399         if (pm_runtime_suspended(dev))
 400                 return 0;
 401
 402         __twl4030_phy_power(twl, 0);
 403         regulator_disable(twl->usb1v5);
 404         regulator_disable(twl->usb1v8);
 405         regulator_disable(twl->usb3v1);
 406
 407         return 0;
 408 }
 409
 410 static int twl4030_usb_runtime_resume(struct device *dev)
 411 {
 412         struct twl4030_usb *twl = dev_get_drvdata(dev);
 413         int res;
 414
 415         dev_dbg(twl->dev, "%s\n", __func__);
 416         if (pm_runtime_active(dev))
 417                 return 0;
 418
 419         res = regulator_enable(twl->usb3v1);
 420         if (res)
 421                 dev_err(twl->dev, "Failed to enable usb3v1\n");
 422
 423         res = regulator_enable(twl->usb1v8);
 424         if (res)
 425                 dev_err(twl->dev, "Failed to enable usb1v8\n");
 426
 427         /*
 428          * Disabling usb3v1 regulator (= writing 0 to VUSB3V1_DEV_GRP
 429          * in twl4030) resets the VUSB_DEDICATED2 register. This reset
 430          * enables VUSB3V1_SLEEP bit that remaps usb3v1 ACTIVE state to
 431          * SLEEP. We work around this by clearing the bit after usv3v1
 432          * is re-activated. This ensures that VUSB3V1 is really active.
 433          */
 434         twl_i2c_write_u8(TWL_MODULE_PM_RECEIVER, 0, VUSB_DEDICATED2);
 435
 436         res = regulator_enable(twl->usb1v5);
 437         if (res)
 438                 dev_err(twl->dev, "Failed to enable usb1v5\n");
 439
 440         __twl4030_phy_power(twl, 1);
 441         twl4030_usb_write(twl, PHY_CLK_CTRL,
 442                           twl4030_usb_read(twl, PHY_CLK_CTRL) |
 443                           (PHY_CLK_CTRL_CLOCKGATING_EN |
 444                            PHY_CLK_CTRL_CLK32K_EN));
 445
 446         return 0;
 447 }
 448
 449 static int twl4030_phy_power_off(struct phy *phy)
 450 {
 451         struct twl4030_usb *twl = phy_get_drvdata(phy);
 452
 453         dev_dbg(twl->dev, "%s\n", __func__);
 454         pm_runtime_mark_last_busy(twl->dev);
 455         pm_runtime_put_autosuspend(twl->dev);
 456
 457         return 0;
 458 }
 459
 460 static int twl4030_phy_power_on(struct phy *phy)
 461 {
 462         struct twl4030_usb *twl = phy_get_drvdata(phy);
 463
 464         dev_dbg(twl->dev, "%s\n", __func__);
 465         pm_runtime_get_sync(twl->dev);
 466         twl4030_i2c_access(twl, 1);
 467         twl4030_usb_set_mode(twl, twl->usb_mode);
 468         if (twl->usb_mode == T2_USB_MODE_ULPI)
 469                 twl4030_i2c_access(twl, 0);
 470         schedule_delayed_work(&twl->id_workaround_work, 0);
 471
 472         return 0;
 473 }
 474
 475 static int twl4030_usb_ldo_init(struct twl4030_usb *twl)
 476 {
 477         /* Enable writing to power configuration registers */
 478         twl_i2c_write_u8(TWL_MODULE_PM_MASTER, TWL4030_PM_MASTER_KEY_CFG1,
 479                          TWL4030_PM_MASTER_PROTECT_KEY);
 480
 481         twl_i2c_write_u8(TWL_MODULE_PM_MASTER, TWL4030_PM_MASTER_KEY_CFG2,
 482                          TWL4030_PM_MASTER_PROTECT_KEY);
 483
 484         /* Keep VUSB3V1 LDO in sleep state until VBUS/ID change detected*/
 485         /*twl_i2c_write_u8(TWL_MODULE_PM_RECEIVER, 0, VUSB_DEDICATED2);*/
 486
 487         /* input to VUSB3V1 LDO is from VBAT, not VBUS */
 488         twl_i2c_write_u8(TWL_MODULE_PM_RECEIVER, 0x14, VUSB_DEDICATED1);
 489
 490         /* Initialize 3.1V regulator */
 491         twl_i2c_write_u8(TWL_MODULE_PM_RECEIVER, 0, VUSB3V1_DEV_GRP);
 492
 493         twl->usb3v1 = devm_regulator_get(twl->dev, "usb3v1");
 494         if (IS_ERR(twl->usb3v1))
 495                 return -ENODEV;
 496
 497         twl_i2c_write_u8(TWL_MODULE_PM_RECEIVER, 0, VUSB3V1_TYPE);
 498
 499         /* Initialize 1.5V regulator */
 500         twl_i2c_write_u8(TWL_MODULE_PM_RECEIVER, 0, VUSB1V5_DEV_GRP);
 501
 502         twl->usb1v5 = devm_regulator_get(twl->dev, "usb1v5");
 503         if (IS_ERR(twl->usb1v5))
 504                 return -ENODEV;
 505
 506         twl_i2c_write_u8(TWL_MODULE_PM_RECEIVER, 0, VUSB1V5_TYPE);
 507
 508         /* Initialize 1.8V regulator */
 509         twl_i2c_write_u8(TWL_MODULE_PM_RECEIVER, 0, VUSB1V8_DEV_GRP);
 510
 511         twl->usb1v8 = devm_regulator_get(twl->dev, "usb1v8");
 512         if (IS_ERR(twl->usb1v8))
 513                 return -ENODEV;
 514
 515         twl_i2c_write_u8(TWL_MODULE_PM_RECEIVER, 0, VUSB1V8_TYPE);
 516
 517         /* disable access to power configuration registers */
 518         twl_i2c_write_u8(TWL_MODULE_PM_MASTER, 0,
 519                          TWL4030_PM_MASTER_PROTECT_KEY);
 520
 521         return 0;
 522 }
 523
 524 static ssize_t twl4030_usb_vbus_show(struct device *dev,
 525                 struct device_attribute *attr, char *buf)
 526 {
 527         struct twl4030_usb *twl = dev_get_drvdata(dev);
 528         int ret = -EINVAL;
 529
 530         mutex_lock(&twl->lock);
 531         ret = sprintf(buf, "%s\n",
 532                         twl->vbus_supplied ? "on" : "off");
 533         mutex_unlock(&twl->lock);
 534
 535         return ret;
 536 }
 537 static DEVICE_ATTR(vbus, 0444, twl4030_usb_vbus_show, NULL);
 538
 539 static irqreturn_t twl4030_usb_irq(int irq, void *_twl)
 540 {
 541         struct twl4030_usb *twl = _twl;
 542         enum omap_musb_vbus_id_status status;
 543         bool status_changed = false;
 544
 545         status = twl4030_usb_linkstat(twl);
 546
 547         mutex_lock(&twl->lock);
 548         if (status >= 0 && status != twl->linkstat) {
 549                 status_changed =
 550                         cable_present(twl->linkstat) !=
 551                         cable_present(status);
 552                 twl->linkstat = status;
 553         }
 554         mutex_unlock(&twl->lock);
 555
 556         if (status_changed) {
 557                 /* FIXME add a set_power() method so that B-devices can
 558                  * configure the charger appropriately.  It's not always
 559                  * correct to consume VBUS power, and how much current to
 560                  * consume is a function of the USB configuration chosen
 561                  * by the host.
 562                  *
 563                  * REVISIT usb_gadget_vbus_connect(...) as needed, ditto
 564                  * its disconnect() sibling, when changing to/from the
 565                  * USB_LINK_VBUS state.  musb_hdrc won't care until it
 566                  * starts to handle softconnect right.
 567                  */
 568                 if (cable_present(status)) {
 569                         pm_runtime_get_sync(twl->dev);
 570                 } else {
 571                         pm_runtime_mark_last_busy(twl->dev);
 572                         pm_runtime_put_autosuspend(twl->dev);
 573                 }
 574                 omap_musb_mailbox(status);
 575         }
 576
 577         /* don't schedule during sleep - irq works right then */
 578         if (status == OMAP_MUSB_ID_GROUND && pm_runtime_active(twl->dev)) {
 579                 cancel_delayed_work(&twl->id_workaround_work);
 580                 schedule_delayed_work(&twl->id_workaround_work, HZ);
 581         }
 582
 583         if (irq)
 584                 sysfs_notify(&twl->dev->kobj, NULL, "vbus");
 585
 586         return IRQ_HANDLED;
 587 }
 588
 589 static void twl4030_id_workaround_work(struct work_struct *work)
 590 {
 591         struct twl4030_usb *twl = container_of(work, struct twl4030_usb,
 592                 id_workaround_work.work);
 593
 594         twl4030_usb_irq(0, twl);
 595 }
 596
 597 static int twl4030_phy_init(struct phy *phy)
 598 {
 599         struct twl4030_usb *twl = phy_get_drvdata(phy);
 600
 601         pm_runtime_get_sync(twl->dev);
 602         schedule_delayed_work(&twl->id_workaround_work, 0);
 603         pm_runtime_mark_last_busy(twl->dev);
 604         pm_runtime_put_autosuspend(twl->dev);
 605
 606         return 0;
 607 }
 608
 609 static int twl4030_set_peripheral(struct usb_otg *otg,
 610                                         struct usb_gadget *gadget)
 611 {
 612         if (!otg)
 613                 return -ENODEV;
 614
 615         otg->gadget = gadget;
 616         if (!gadget)
 617                 otg->state = OTG_STATE_UNDEFINED;
 618
 619         return 0;
 620 }
 621
 622 static int twl4030_set_host(struct usb_otg *otg, struct usb_bus *host)
 623 {
 624         if (!otg)
 625                 return -ENODEV;
 626
 627         otg->host = host;
 628         if (!host)
 629                 otg->state = OTG_STATE_UNDEFINED;
 630
 631         return 0;
 632 }
 633
 634 static const struct phy_ops ops = {
 635         .init           = twl4030_phy_init,
 636         .power_on       = twl4030_phy_power_on,
 637         .power_off      = twl4030_phy_power_off,
 638         .owner          = THIS_MODULE,
 639 };
 640
 641 static const struct dev_pm_ops twl4030_usb_pm_ops = {
 642         SET_RUNTIME_PM_OPS(twl4030_usb_runtime_suspend,
 643                            twl4030_usb_runtime_resume, NULL)
 644 };
 645
 646 static int twl4030_usb_probe(struct platform_device *pdev)
 647 {
 648         struct twl4030_usb_data *pdata = dev_get_platdata(&pdev->dev);
 649         struct twl4030_usb      *twl;
 650         struct phy              *phy;
 651         int                     status, err;
 652         struct usb_otg          *otg;
 653         struct device_node      *np = pdev->dev.of_node;
 654         struct phy_provider     *phy_provider;
 655
 656         twl = devm_kzalloc(&pdev->dev, sizeof(*twl), GFP_KERNEL);
 657         if (!twl)
 658                 return -ENOMEM;
 659
 660         if (np)
 661                 of_property_read_u32(np, "usb_mode",
 662                                 (enum twl4030_usb_mode *)&twl->usb_mode);
 663         else if (pdata) {
 664                 twl->usb_mode = pdata->usb_mode;
 665         } else {
 666                 dev_err(&pdev->dev, "twl4030 initialized without pdata\n");
 667                 return -EINVAL;
 668         }
 669
 670         otg = devm_kzalloc(&pdev->dev, sizeof(*otg), GFP_KERNEL);
 671         if (!otg)
 672                 return -ENOMEM;
 673
 674         twl->dev                = &pdev->dev;
 675         twl->irq                = platform_get_irq(pdev, 0);
 676         twl->vbus_supplied      = false;
 677         twl->linkstat           = OMAP_MUSB_UNKNOWN;
 678
 679         twl->phy.dev            = twl->dev;
 680         twl->phy.label          = "twl4030";
 681         twl->phy.otg            = otg;
 682         twl->phy.type           = USB_PHY_TYPE_USB2;
 683
 684         otg->usb_phy            = &twl->phy;
 685         otg->set_host           = twl4030_set_host;
 686         otg->set_peripheral     = twl4030_set_peripheral;
 687
 688         phy = devm_phy_create(twl->dev, NULL, &ops);
 689         if (IS_ERR(phy)) {
 690                 dev_dbg(&pdev->dev, "Failed to create PHY\n");
 691                 return PTR_ERR(phy);
 692         }
 693
 694         phy_set_drvdata(phy, twl);
 695
 696         phy_provider = devm_of_phy_provider_register(twl->dev,
 697                 of_phy_simple_xlate);
 698         if (IS_ERR(phy_provider))
 699                 return PTR_ERR(phy_provider);
 700
 701         /* init mutex for workqueue */
 702         mutex_init(&twl->lock);
 703
 704         INIT_DELAYED_WORK(&twl->id_workaround_work, twl4030_id_workaround_work);
 705
 706         err = twl4030_usb_ldo_init(twl);
 707         if (err) {
 708                 dev_err(&pdev->dev, "ldo init failed\n");
 709                 return err;
 710         }
 711         usb_add_phy_dev(&twl->phy);
 712
 713         platform_set_drvdata(pdev, twl);
 714         if (device_create_file(&pdev->dev, &dev_attr_vbus))
 715                 dev_warn(&pdev->dev, "could not create sysfs file\n");
 716
 717         ATOMIC_INIT_NOTIFIER_HEAD(&twl->phy.notifier);
 718
 719         pm_runtime_use_autosuspend(&pdev->dev);
 720         pm_runtime_set_autosuspend_delay(&pdev->dev, 2000);
 721         pm_runtime_enable(&pdev->dev);
 722
 723         /* Our job is to use irqs and status from the power module
 724          * to keep the transceiver disabled when nothing's connected.
 725          *
 726          * FIXME we actually shouldn't start enabling it until the
 727          * USB controller drivers have said they're ready, by calling
 728          * set_host() and/or set_peripheral() ... OTG_capable boards
 729          * need both handles, otherwise just one suffices.
 730          */
 731         status = devm_request_threaded_irq(twl->dev, twl->irq, NULL,
 732                         twl4030_usb_irq, IRQF_TRIGGER_FALLING |
 733                         IRQF_TRIGGER_RISING | IRQF_ONESHOT, "twl4030_usb", twl);
 734         if (status < 0) {
 735                 dev_dbg(&pdev->dev, "can't get IRQ %d, err %d\n",
 736                         twl->irq, status);
 737                 return status;
 738         }
 739
 740         if (pdata)
 741                 err = phy_create_lookup(phy, "usb", "musb-hdrc.0");
 742         if (err)
 743                 return err;
 744
 745         pm_runtime_mark_last_busy(&pdev->dev);
 746         pm_runtime_put_autosuspend(twl->dev);
 747
 748         dev_info(&pdev->dev, "Initialized TWL4030 USB module\n");
 749         return 0;
 750 }
 751
 752 static int twl4030_usb_remove(struct platform_device *pdev)
 753 {
 754         struct twl4030_usb *twl = platform_get_drvdata(pdev);
 755         int val;
 756
 757         pm_runtime_get_sync(twl->dev);
 758         cancel_delayed_work(&twl->id_workaround_work);
 759         device_remove_file(twl->dev, &dev_attr_vbus);
 760
 761         /* set transceiver mode to power on defaults */
 762         twl4030_usb_set_mode(twl, -1);
 763
 764         /* autogate 60MHz ULPI clock,
 765          * clear dpll clock request for i2c access,
 766          * disable 32KHz
 767          */
 768         val = twl4030_usb_read(twl, PHY_CLK_CTRL);
 769         if (val >= 0) {
 770                 val |= PHY_CLK_CTRL_CLOCKGATING_EN;
 771                 val &= ~(PHY_CLK_CTRL_CLK32K_EN | REQ_PHY_DPLL_CLK);
 772                 twl4030_usb_write(twl, PHY_CLK_CTRL, (u8)val);
 773         }
 774
 775         /* disable complete OTG block */
 776         twl4030_usb_clear_bits(twl, POWER_CTRL, POWER_CTRL_OTG_ENAB);
 777
 778         if (cable_present(twl->linkstat))
 779                 pm_runtime_put_noidle(twl->dev);
 780         pm_runtime_mark_last_busy(twl->dev);
 781         pm_runtime_put(twl->dev);
 782
 783         return 0;
 784 }
 785
 786 #ifdef CONFIG_OF
 787 static const struct of_device_id twl4030_usb_id_table[] = {
 788         { .compatible = "ti,twl4030-usb" },
 789         {}
 790 };
 791 MODULE_DEVICE_TABLE(of, twl4030_usb_id_table);
 792 #endif
 793
 794 static struct platform_driver twl4030_usb_driver = {
 795         .probe          = twl4030_usb_probe,
 796         .remove         = twl4030_usb_remove,
 797         .driver         = {
 798                 .name   = "twl4030_usb",
 799                 .pm     = &twl4030_usb_pm_ops,
 800                 .of_match_table = of_match_ptr(twl4030_usb_id_table),
 801         },
 802 };
 803
 804 static int __init twl4030_usb_init(void)
 805 {
 806         return platform_driver_register(&twl4030_usb_driver);
 807 }
 808 subsys_initcall(twl4030_usb_init);
 809
 810 static void __exit twl4030_usb_exit(void)
 811 {
 812         platform_driver_unregister(&twl4030_usb_driver);
 813 }
 814 module_exit(twl4030_usb_exit);
 815
 816 MODULE_ALIAS("platform:twl4030_usb");
 817 MODULE_AUTHOR("Texas Instruments, Inc, Nokia Corporation");
 818 MODULE_DESCRIPTION("TWL4030 USB transceiver driver");
 819 MODULE_LICENSE("GPL");