====================== Monitoring a Cluster ====================== Once you have a running cluster, you may use the ``ceph`` tool to monitor your cluster. Monitoring a cluster typically involves checking OSD status, monitor status, placement group status and metadata server status. Using the command line ====================== Interactive mode ---------------- To run the ``ceph`` tool in interactive mode, type ``ceph`` at the command line with no arguments. For example:: ceph ceph> health ceph> status ceph> quorum_status ceph> mon_status Non-default paths ----------------- If you specified non-default locations for your configuration or keyring, you may specify their locations:: ceph -c /path/to/conf -k /path/to/keyring health Checking a Cluster's Status =========================== After you start your cluster, and before you start reading and/or writing data, check your cluster's status first. To check a cluster's status, execute the following:: ceph status Or:: ceph -s In interactive mode, type ``status`` and press **Enter**. :: ceph> status Ceph will print the cluster status. For example, a tiny Ceph demonstration cluster with one of each service may print the following: :: cluster: id: 477e46f1-ae41-4e43-9c8f-72c918ab0a20 health: HEALTH_OK services: mon: 1 daemons, quorum a mgr: x(active) mds: 1/1/1 up {0=a=up:active} osd: 1 osds: 1 up, 1 in data: pools: 2 pools, 16 pgs objects: 21 objects, 2246 bytes usage: 546 GB used, 384 GB / 931 GB avail pgs: 16 active+clean .. topic:: How Ceph Calculates Data Usage The ``usage`` value reflects the *actual* amount of raw storage used. The ``xxx GB / xxx GB`` value means the amount available (the lesser number) of the overall storage capacity of the cluster. The notional number reflects the size of the stored data before it is replicated, cloned or snapshotted. Therefore, the amount of data actually stored typically exceeds the notional amount stored, because Ceph creates replicas of the data and may also use storage capacity for cloning and snapshotting. Watching a Cluster ================== In addition to local logging by each daemon, Ceph clusters maintain a *cluster log* that records high level events about the whole system. This is logged to disk on monitor servers (as ``/var/log/ceph/ceph.log`` by default), but can also be monitored via the command line. To follow the cluster log, use the following command :: ceph -w Ceph will print the status of the system, followed by each log message as it is emitted. For example: :: cluster: id: 477e46f1-ae41-4e43-9c8f-72c918ab0a20 health: HEALTH_OK services: mon: 1 daemons, quorum a mgr: x(active) mds: 1/1/1 up {0=a=up:active} osd: 1 osds: 1 up, 1 in data: pools: 2 pools, 16 pgs objects: 21 objects, 2246 bytes usage: 546 GB used, 384 GB / 931 GB avail pgs: 16 active+clean 2017-07-24 08:15:11.329298 mon.a mon.0 172.21.9.34:6789/0 23 : cluster [INF] osd.0 172.21.9.34:6806/20527 boot 2017-07-24 08:15:14.258143 mon.a mon.0 172.21.9.34:6789/0 39 : cluster [INF] Activating manager daemon x 2017-07-24 08:15:15.446025 mon.a mon.0 172.21.9.34:6789/0 47 : cluster [INF] Manager daemon x is now available In addition to using ``ceph -w`` to print log lines as they are emitted, use ``ceph log last [n]`` to see the most recent ``n`` lines from the cluster log. Monitoring Health Checks ======================== Ceph continously runs various *health checks* against its own status. When a health check fails, this is reflected in the output of ``ceph status`` (or ``ceph health``). In addition, messages are sent to the cluster log to indicate when a check fails, and when the cluster recovers. For example, when an OSD goes down, the ``health`` section of the status output may be updated as follows: :: health: HEALTH_WARN 1 osds down Degraded data redundancy: 21/63 objects degraded (33.333%), 16 pgs unclean, 16 pgs degraded At this time, cluster log messages are also emitted to record the failure of the health checks: :: 2017-07-25 10:08:58.265945 mon.a mon.0 172.21.9.34:6789/0 91 : cluster [WRN] Health check failed: 1 osds down (OSD_DOWN) 2017-07-25 10:09:01.302624 mon.a mon.0 172.21.9.34:6789/0 94 : cluster [WRN] Health check failed: Degraded data redundancy: 21/63 objects degraded (33.333%), 16 pgs unclean, 16 pgs degraded (PG_DEGRADED) When the OSD comes back online, the cluster log records the cluster's return to a health state: :: 2017-07-25 10:11:11.526841 mon.a mon.0 172.21.9.34:6789/0 109 : cluster [WRN] Health check update: Degraded data redundancy: 2 pgs unclean, 2 pgs degraded, 2 pgs undersized (PG_DEGRADED) 2017-07-25 10:11:13.535493 mon.a mon.0 172.21.9.34:6789/0 110 : cluster [INF] Health check cleared: PG_DEGRADED (was: Degraded data redundancy: 2 pgs unclean, 2 pgs degraded, 2 pgs undersized) 2017-07-25 10:11:13.535577 mon.a mon.0 172.21.9.34:6789/0 111 : cluster [INF] Cluster is now healthy Detecting configuration issues ============================== In addition to the health checks that Ceph continuously runs on its own status, there are some configuration issues that may only be detected by an external tool. Use the `ceph-medic`_ tool to run these additional checks on your Ceph cluster's configuration. Checking a Cluster's Usage Stats ================================ To check a cluster's data usage and data distribution among pools, you can use the ``df`` option. It is similar to Linux ``df``. Execute the following:: ceph df The **GLOBAL** section of the output provides an overview of the amount of storage your cluster uses for your data. - **SIZE:** The overall storage capacity of the cluster. - **AVAIL:** The amount of free space available in the cluster. - **RAW USED:** The amount of raw storage used. - **% RAW USED:** The percentage of raw storage used. Use this number in conjunction with the ``full ratio`` and ``near full ratio`` to ensure that you are not reaching your cluster's capacity. See `Storage Capacity`_ for additional details. The **POOLS** section of the output provides a list of pools and the notional usage of each pool. The output from this section **DOES NOT** reflect replicas, clones or snapshots. For example, if you store an object with 1MB of data, the notional usage will be 1MB, but the actual usage may be 2MB or more depending on the number of replicas, clones and snapshots. - **NAME:** The name of the pool. - **ID:** The pool ID. - **USED:** The notional amount of data stored in kilobytes, unless the number appends **M** for megabytes or **G** for gigabytes. - **%USED:** The notional percentage of storage used per pool. - **MAX AVAIL:** An estimate of the notional amount of data that can be written to this pool. - **Objects:** The notional number of objects stored per pool. .. note:: The numbers in the **POOLS** section are notional. They are not inclusive of the number of replicas, shapshots or clones. As a result, the sum of the **USED** and **%USED** amounts will not add up to the **RAW USED** and **%RAW USED** amounts in the **GLOBAL** section of the output. .. note:: The **MAX AVAIL** value is a complicated function of the replication or erasure code used, the CRUSH rule that maps storage to devices, the utilization of those devices, and the configured mon_osd_full_ratio. Checking OSD Status =================== You can check OSDs to ensure they are ``up`` and ``in`` by executing:: ceph osd stat Or:: ceph osd dump You can also check view OSDs according to their position in the CRUSH map. :: ceph osd tree Ceph will print out a CRUSH tree with a host, its OSDs, whether they are up and their weight. :: # id weight type name up/down reweight -1 3 pool default -3 3 rack mainrack -2 3 host osd-host 0 1 osd.0 up 1 1 1 osd.1 up 1 2 1 osd.2 up 1 For a detailed discussion, refer to `Monitoring OSDs and Placement Groups`_. Checking Monitor Status ======================= If your cluster has multiple monitors (likely), you should check the monitor quorum status after you start the cluster before reading and/or writing data. A quorum must be present when multiple monitors are running. You should also check monitor status periodically to ensure that they are running. To see display the monitor map, execute the following:: ceph mon stat Or:: ceph mon dump To check the quorum status for the monitor cluster, execute the following:: ceph quorum_status Ceph will return the quorum status. For example, a Ceph cluster consisting of three monitors may return the following: .. code-block:: javascript { "election_epoch": 10, "quorum": [ 0, 1, 2], "monmap": { "epoch": 1, "fsid": "444b489c-4f16-4b75-83f0-cb8097468898", "modified": "2011-12-12 13:28:27.505520", "created": "2011-12-12 13:28:27.505520", "mons": [ { "rank": 0, "name": "a", "addr": "127.0.0.1:6789\/0"}, { "rank": 1, "name": "b", "addr": "127.0.0.1:6790\/0"}, { "rank": 2, "name": "c", "addr": "127.0.0.1:6791\/0"} ] } } Checking MDS Status =================== Metadata servers provide metadata services for Ceph FS. Metadata servers have two sets of states: ``up | down`` and ``active | inactive``. To ensure your metadata servers are ``up`` and ``active``, execute the following:: ceph mds stat To display details of the metadata cluster, execute the following:: ceph fs dump Checking Placement Group States =============================== Placement groups map objects to OSDs. When you monitor your placement groups, you will want them to be ``active`` and ``clean``. For a detailed discussion, refer to `Monitoring OSDs and Placement Groups`_. .. _Monitoring OSDs and Placement Groups: ../monitoring-osd-pg Using the Admin Socket ====================== The Ceph admin socket allows you to query a daemon via a socket interface. By default, Ceph sockets reside under ``/var/run/ceph``. To access a daemon via the admin socket, login to the host running the daemon and use the following command:: ceph daemon {daemon-name} ceph daemon {path-to-socket-file} For example, the following are equivalent:: ceph daemon osd.0 foo ceph daemon /var/run/ceph/ceph-osd.0.asok foo To view the available admin socket commands, execute the following command:: ceph daemon {daemon-name} help The admin socket command enables you to show and set your configuration at runtime. See `Viewing a Configuration at Runtime`_ for details. Additionally, you can set configuration values at runtime directly (i.e., the admin socket bypasses the monitor, unlike ``ceph tell {daemon-type}.{id} injectargs``, which relies on the monitor but doesn't require you to login directly to the host in question ). .. _Viewing a Configuration at Runtime: ../../configuration/ceph-conf#ceph-runtime-config .. _Storage Capacity: ../../configuration/mon-config-ref#storage-capacity .. _ceph-medic: http://docs.ceph.com/ceph-medic/master/