--- /dev/null
+/*
+ * (C) Copyright 2000-2004
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+/*
+ * The purpose of this code is to signal the operational status of a
+ * target which usually boots over the network; while running in
+ * PCBoot, a status LED is blinking. As soon as a valid BOOTP reply
+ * message has been received, the LED is turned off. The Linux
+ * kernel, once it is running, will start blinking the LED again,
+ * with another frequency.
+ */
+
+#ifndef _STATUS_LED_H_
+#define _STATUS_LED_H_
+
+#ifdef CONFIG_STATUS_LED
+
+#define STATUS_LED_OFF 0
+#define STATUS_LED_BLINKING 1
+#define STATUS_LED_ON 2
+
+void status_led_tick (unsigned long timestamp);
+void status_led_set (int led, int state);
+
+/***** TQM8xxL ********************************************************/
+#if defined(CONFIG_TQM8xxL)
+# define STATUS_LED_PAR im_cpm.cp_pbpar
+# define STATUS_LED_DIR im_cpm.cp_pbdir
+# define STATUS_LED_ODR im_cpm.cp_pbodr
+# define STATUS_LED_DAT im_cpm.cp_pbdat
+
+# define STATUS_LED_BIT 0x00000001
+# define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 2)
+# define STATUS_LED_STATE STATUS_LED_BLINKING
+
+# define STATUS_LED_ACTIVE 1 /* LED on for bit == 1 */
+
+# define STATUS_LED_BOOT 0 /* LED 0 used for boot status */
+
+/***** MVS v1 **********************************************************/
+#elif (defined(CONFIG_MVS) && CONFIG_MVS < 2)
+# define STATUS_LED_PAR im_ioport.iop_pdpar
+# define STATUS_LED_DIR im_ioport.iop_pddir
+# undef STATUS_LED_ODR
+# define STATUS_LED_DAT im_ioport.iop_pddat
+
+# define STATUS_LED_BIT 0x00000001
+# define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 2)
+# define STATUS_LED_STATE STATUS_LED_BLINKING
+
+# define STATUS_LED_ACTIVE 1 /* LED on for bit == 1 */
+
+# define STATUS_LED_BOOT 0 /* LED 0 used for boot status */
+
+/***** GEN860T *********************************************************/
+#elif defined(CONFIG_GEN860T)
+
+# define STATUS_LED_PAR im_ioport.iop_papar
+# define STATUS_LED_DIR im_ioport.iop_padir
+# define STATUS_LED_ODR im_ioport.iop_paodr
+# define STATUS_LED_DAT im_ioport.iop_padat
+
+# define STATUS_LED_BIT 0x0800 /* Red LED 0 is on PA.4 */
+# define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 4)
+# define STATUS_LED_STATE STATUS_LED_OFF
+# define STATUS_LED_BIT1 0x0400 /* Grn LED 1 is on PA.5 */
+# define STATUS_LED_PERIOD1 (CONFIG_SYS_HZ / 8)
+# define STATUS_LED_STATE1 STATUS_LED_BLINKING
+# define STATUS_LED_BIT2 0x0080 /* Red LED 2 is on PA.8 */
+# define STATUS_LED_PERIOD2 (CONFIG_SYS_HZ / 4)
+# define STATUS_LED_STATE2 STATUS_LED_OFF
+# define STATUS_LED_BIT3 0x0040 /* Grn LED 3 is on PA.9 */
+# define STATUS_LED_PERIOD3 (CONFIG_SYS_HZ / 4)
+# define STATUS_LED_STATE3 STATUS_LED_OFF
+
+# define STATUS_LED_ACTIVE 1 /* LED on for bit == 1 */
+# define STATUS_LED_BOOT 1 /* Boot status on LED 1 */
+
+/***** IVMS8 **********************************************************/
+#elif defined(CONFIG_IVMS8)
+
+# define STATUS_LED_PAR im_cpm.cp_pbpar
+# define STATUS_LED_DIR im_cpm.cp_pbdir
+# define STATUS_LED_ODR im_cpm.cp_pbodr
+# define STATUS_LED_DAT im_cpm.cp_pbdat
+
+# define STATUS_LED_BIT 0x00000010 /* LED 0 is on PB.27 */
+# define STATUS_LED_PERIOD (1 * CONFIG_SYS_HZ)
+# define STATUS_LED_STATE STATUS_LED_OFF
+# define STATUS_LED_BIT1 0x00000020 /* LED 1 is on PB.26 */
+# define STATUS_LED_PERIOD1 (1 * CONFIG_SYS_HZ)
+# define STATUS_LED_STATE1 STATUS_LED_OFF
+/* IDE LED usable for other purposes, too */
+# define STATUS_LED_BIT2 0x00000008 /* LED 2 is on PB.28 */
+# define STATUS_LED_PERIOD2 (1 * CONFIG_SYS_HZ)
+# define STATUS_LED_STATE2 STATUS_LED_OFF
+
+# define STATUS_LED_ACTIVE 1 /* LED on for bit == 1 */
+
+# define STATUS_ILOCK_SWITCH 0x00800000 /* ILOCK switch in IRQ4 */
+
+# define STATUS_ILOCK_PERIOD (CONFIG_SYS_HZ / 10) /* about every 100 ms */
+
+# define STATUS_LED_YELLOW 0
+# define STATUS_LED_GREEN 1
+# define STATUS_LED_BOOT 2 /* IDE LED used for boot status */
+
+/***** IVML24 *********************************************************/
+#elif defined(CONFIG_IVML24)
+
+# define STATUS_LED_PAR im_cpm.cp_pbpar
+# define STATUS_LED_DIR im_cpm.cp_pbdir
+# define STATUS_LED_ODR im_cpm.cp_pbodr
+# define STATUS_LED_DAT im_cpm.cp_pbdat
+
+# define STATUS_LED_BIT 0x00000010 /* LED 0 is on PB.27 */
+# define STATUS_LED_PERIOD (1 * CONFIG_SYS_HZ)
+# define STATUS_LED_STATE STATUS_LED_OFF
+# define STATUS_LED_BIT1 0x00000020 /* LED 1 is on PB.26 */
+# define STATUS_LED_PERIOD1 (1 * CONFIG_SYS_HZ)
+# define STATUS_LED_STATE1 STATUS_LED_OFF
+/* IDE LED usable for other purposes, too */
+# define STATUS_LED_BIT2 0x00000008 /* LED 2 is on PB.28 */
+# define STATUS_LED_PERIOD2 (1 * CONFIG_SYS_HZ)
+# define STATUS_LED_STATE2 STATUS_LED_OFF
+
+# define STATUS_LED_ACTIVE 1 /* LED on for bit == 1 */
+
+# define STATUS_ILOCK_SWITCH 0x00004000 /* ILOCK is on PB.17 */
+
+# define STATUS_ILOCK_PERIOD (CONFIG_SYS_HZ / 10) /* about every 100 ms */
+
+# define STATUS_LED_YELLOW 0
+# define STATUS_LED_GREEN 1
+# define STATUS_LED_BOOT 2 /* IDE LED used for boot status */
+
+/***** ICU862 ********************************************************/
+#elif defined(CONFIG_ICU862)
+
+# define STATUS_LED_PAR im_ioport.iop_papar
+# define STATUS_LED_DIR im_ioport.iop_padir
+# define STATUS_LED_ODR im_ioport.iop_paodr
+# define STATUS_LED_DAT im_ioport.iop_padat
+
+# define STATUS_LED_BIT 0x4000 /* LED 0 is on PA.1 */
+# define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 2)
+# define STATUS_LED_STATE STATUS_LED_BLINKING
+# define STATUS_LED_BIT1 0x1000 /* LED 1 is on PA.3 */
+# define STATUS_LED_PERIOD1 (CONFIG_SYS_HZ)
+# define STATUS_LED_STATE1 STATUS_LED_OFF
+
+# define STATUS_LED_ACTIVE 1 /* LED on for bit == 1 */
+
+# define STATUS_LED_BOOT 0 /* LED 0 used for boot status */
+
+/***** Someone else defines these *************************************/
+#elif defined(STATUS_LED_PAR)
+
+ /*
+ * ADVICE: Define in your board configuration file rather than
+ * filling this file up with lots of custom board stuff.
+ */
+
+/***** NetVia ********************************************************/
+#elif defined(CONFIG_NETVIA)
+
+#if !defined(CONFIG_NETVIA_VERSION) || CONFIG_NETVIA_VERSION == 1
+
+#define STATUS_LED_PAR im_ioport.iop_pdpar
+#define STATUS_LED_DIR im_ioport.iop_pddir
+#undef STATUS_LED_ODR
+#define STATUS_LED_DAT im_ioport.iop_pddat
+
+# define STATUS_LED_BIT 0x0080 /* PD.8 */
+# define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 2)
+# define STATUS_LED_STATE STATUS_LED_BLINKING
+
+# define STATUS_LED_BIT1 0x0040 /* PD.9 */
+# define STATUS_LED_PERIOD1 (CONFIG_SYS_HZ / 2)
+# define STATUS_LED_STATE1 STATUS_LED_OFF
+
+# define STATUS_LED_ACTIVE 0 /* LED on for bit == 0 */
+# define STATUS_LED_BOOT 0 /* LED 0 used for boot status */
+
+#endif
+
+/***** CMI ********************************************************/
+#elif defined(CONFIG_CMI)
+# define STATUS_LED_DIR im_mios.mios_mpiosm32ddr
+# define STATUS_LED_DAT im_mios.mios_mpiosm32dr
+
+# define STATUS_LED_BIT 0x2000 /* Select one of the 16 possible*/
+ /* MIOS outputs */
+# define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 2) /* Blinking periode is 500 ms */
+# define STATUS_LED_STATE STATUS_LED_BLINKING
+
+# define STATUS_LED_ACTIVE 1 /* LED on for bit == 0 */
+# define STATUS_LED_BOOT 0 /* LED 0 used for boot status */
+
+/***** KUP4K, KUP4X ****************************************************/
+#elif defined(CONFIG_KUP4K) || defined(CONFIG_KUP4X)
+
+# define STATUS_LED_PAR im_ioport.iop_papar
+# define STATUS_LED_DIR im_ioport.iop_padir
+# define STATUS_LED_ODR im_ioport.iop_paodr
+# define STATUS_LED_DAT im_ioport.iop_padat
+
+# define STATUS_LED_BIT 0x00000300 /* green + red PA[8]=yellow, PA[7]=red, PA[6]=green */
+# define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 2)
+# define STATUS_LED_STATE STATUS_LED_BLINKING
+
+# define STATUS_LED_ACTIVE 1 /* LED on for bit == 1 */
+
+# define STATUS_LED_BOOT 0 /* LED 0 used for boot status */
+
+#elif defined(CONFIG_SVM_SC8xx)
+# define STATUS_LED_PAR im_cpm.cp_pbpar
+# define STATUS_LED_DIR im_cpm.cp_pbdir
+# define STATUS_LED_ODR im_cpm.cp_pbodr
+# define STATUS_LED_DAT im_cpm.cp_pbdat
+
+# define STATUS_LED_BIT 0x00000001
+# define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 2)
+# define STATUS_LED_STATE STATUS_LED_BLINKING
+
+# define STATUS_LED_ACTIVE 1 /* LED on for bit == 1 */
+
+# define STATUS_LED_BOOT 0 /* LED 0 used for boot status */
+
+/***** RBC823 ********************************************************/
+#elif defined(CONFIG_RBC823)
+
+# define STATUS_LED_PAR im_ioport.iop_pcpar
+# define STATUS_LED_DIR im_ioport.iop_pcdir
+# undef STATUS_LED_ODR
+# define STATUS_LED_DAT im_ioport.iop_pcdat
+
+# define STATUS_LED_BIT 0x0002 /* LED 0 is on PC.14 */
+# define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 2)
+# define STATUS_LED_STATE STATUS_LED_BLINKING
+# define STATUS_LED_BIT1 0x0004 /* LED 1 is on PC.13 */
+# define STATUS_LED_PERIOD1 (CONFIG_SYS_HZ)
+# define STATUS_LED_STATE1 STATUS_LED_OFF
+
+# define STATUS_LED_ACTIVE 1 /* LED on for bit == 1 */
+
+# define STATUS_LED_BOOT 0 /* LED 0 used for boot status */
+
+/***** NetPhone ********************************************************/
+#elif defined(CONFIG_NETPHONE) || defined(CONFIG_NETTA2)
+/* XXX empty just to avoid the error */
+/***** STx XTc ********************************************************/
+#elif defined(CONFIG_STXXTC)
+/* XXX empty just to avoid the error */
+/************************************************************************/
+#elif defined(CONFIG_V38B)
+
+# define STATUS_LED_BIT 0x0010 /* Timer7 GPIO */
+# define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 2)
+# define STATUS_LED_STATE STATUS_LED_BLINKING
+
+# define STATUS_LED_ACTIVE 0 /* LED on for bit == 0 */
+# define STATUS_LED_BOOT 0 /* LED 0 used for boot status */
+
+#elif defined(CONFIG_MOTIONPRO)
+
+#define STATUS_LED_BIT ((vu_long *) MPC5XXX_GPT6_ENABLE)
+#define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 10)
+#define STATUS_LED_STATE STATUS_LED_BLINKING
+
+#define STATUS_LED_BIT1 ((vu_long *) MPC5XXX_GPT7_ENABLE)
+#define STATUS_LED_PERIOD1 (CONFIG_SYS_HZ / 10)
+#define STATUS_LED_STATE1 STATUS_LED_OFF
+
+#define STATUS_LED_BOOT 0 /* LED 0 used for boot status */
+
+#elif defined(CONFIG_BOARD_SPECIFIC_LED)
+/* led_id_t is unsigned long mask */
+typedef unsigned long led_id_t;
+
+extern void __led_toggle (led_id_t mask);
+extern void __led_init (led_id_t mask, int state);
+extern void __led_set (led_id_t mask, int state);
+#else
+# error Status LED configuration missing
+#endif
+/************************************************************************/
+
+#ifndef CONFIG_BOARD_SPECIFIC_LED
+# include <asm/status_led.h>
+#endif
+
+/*
+ * Coloured LEDs API
+ */
+#ifndef __ASSEMBLY__
+extern void coloured_LED_init (void);
+extern void red_led_on(void);
+extern void red_led_off(void);
+extern void green_led_on(void);
+extern void green_led_off(void);
+extern void yellow_led_on(void);
+extern void yellow_led_off(void);
+extern void blue_led_on(void);
+extern void blue_led_off(void);
+#else
+ .extern LED_init
+ .extern red_led_on
+ .extern red_led_off
+ .extern yellow_led_on
+ .extern yellow_led_off
+ .extern green_led_on
+ .extern green_led_off
+ .extern blue_led_on
+ .extern blue_led_off
+#endif
+
+#endif /* CONFIG_STATUS_LED */
+
+#endif /* _STATUS_LED_H_ */
Code Review / kvmfornfv.git / blobdiff