--- /dev/null
+/*
+ * Copyright 2008,2010 Freescale Semiconductor, Inc
+ * Andy Fleming
+ *
+ * Based (loosely) on the Linux code
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef _MMC_H_
+#define _MMC_H_
+
+#include <linux/list.h>
+#include <linux/compiler.h>
+#include <part.h>
+
+#define SD_VERSION_SD 0x20000
+#define SD_VERSION_3 (SD_VERSION_SD | 0x300)
+#define SD_VERSION_2 (SD_VERSION_SD | 0x200)
+#define SD_VERSION_1_0 (SD_VERSION_SD | 0x100)
+#define SD_VERSION_1_10 (SD_VERSION_SD | 0x10a)
+#define MMC_VERSION_MMC 0x10000
+#define MMC_VERSION_UNKNOWN (MMC_VERSION_MMC)
+#define MMC_VERSION_1_2 (MMC_VERSION_MMC | 0x102)
+#define MMC_VERSION_1_4 (MMC_VERSION_MMC | 0x104)
+#define MMC_VERSION_2_2 (MMC_VERSION_MMC | 0x202)
+#define MMC_VERSION_3 (MMC_VERSION_MMC | 0x300)
+#define MMC_VERSION_4 (MMC_VERSION_MMC | 0x400)
+#define MMC_VERSION_4_1 (MMC_VERSION_MMC | 0x401)
+#define MMC_VERSION_4_2 (MMC_VERSION_MMC | 0x402)
+#define MMC_VERSION_4_3 (MMC_VERSION_MMC | 0x403)
+#define MMC_VERSION_4_41 (MMC_VERSION_MMC | 0x429)
+#define MMC_VERSION_4_5 (MMC_VERSION_MMC | 0x405)
+
+#define MMC_MODE_HS 0x001
+#define MMC_MODE_HS_52MHz 0x010
+#define MMC_MODE_4BIT 0x100
+#define MMC_MODE_8BIT 0x200
+#define MMC_MODE_SPI 0x400
+#define MMC_MODE_HC 0x800
+
+#define MMC_MODE_MASK_WIDTH_BITS (MMC_MODE_4BIT | MMC_MODE_8BIT)
+#define MMC_MODE_WIDTH_BITS_SHIFT 8
+
+#define SD_DATA_4BIT 0x00040000
+
+#define IS_SD(x) (x->version & SD_VERSION_SD)
+
+#define MMC_DATA_READ 1
+#define MMC_DATA_WRITE 2
+
+#define NO_CARD_ERR -16 /* No SD/MMC card inserted */
+#define UNUSABLE_ERR -17 /* Unusable Card */
+#define COMM_ERR -18 /* Communications Error */
+#define TIMEOUT -19
+#define IN_PROGRESS -20 /* operation is in progress */
+
+#define MMC_CMD_GO_IDLE_STATE 0
+#define MMC_CMD_SEND_OP_COND 1
+#define MMC_CMD_ALL_SEND_CID 2
+#define MMC_CMD_SET_RELATIVE_ADDR 3
+#define MMC_CMD_SET_DSR 4
+#define MMC_CMD_SWITCH 6
+#define MMC_CMD_SELECT_CARD 7
+#define MMC_CMD_SEND_EXT_CSD 8
+#define MMC_CMD_SEND_CSD 9
+#define MMC_CMD_SEND_CID 10
+#define MMC_CMD_STOP_TRANSMISSION 12
+#define MMC_CMD_SEND_STATUS 13
+#define MMC_CMD_SET_BLOCKLEN 16
+#define MMC_CMD_READ_SINGLE_BLOCK 17
+#define MMC_CMD_READ_MULTIPLE_BLOCK 18
+#define MMC_CMD_WRITE_SINGLE_BLOCK 24
+#define MMC_CMD_WRITE_MULTIPLE_BLOCK 25
+#define MMC_CMD_ERASE_GROUP_START 35
+#define MMC_CMD_ERASE_GROUP_END 36
+#define MMC_CMD_ERASE 38
+#define MMC_CMD_APP_CMD 55
+#define MMC_CMD_SPI_READ_OCR 58
+#define MMC_CMD_SPI_CRC_ON_OFF 59
+#define MMC_CMD_RES_MAN 62
+
+#define MMC_CMD62_ARG1 0xefac62ec
+#define MMC_CMD62_ARG2 0xcbaea7
+
+
+#define SD_CMD_SEND_RELATIVE_ADDR 3
+#define SD_CMD_SWITCH_FUNC 6
+#define SD_CMD_SEND_IF_COND 8
+
+#define SD_CMD_APP_SET_BUS_WIDTH 6
+#define SD_CMD_ERASE_WR_BLK_START 32
+#define SD_CMD_ERASE_WR_BLK_END 33
+#define SD_CMD_APP_SEND_OP_COND 41
+#define SD_CMD_APP_SEND_SCR 51
+
+/* SCR definitions in different words */
+#define SD_HIGHSPEED_BUSY 0x00020000
+#define SD_HIGHSPEED_SUPPORTED 0x00020000
+
+#define MMC_HS_TIMING 0x00000100
+#define MMC_HS_52MHZ 0x2
+
+#define OCR_BUSY 0x80000000
+#define OCR_HCS 0x40000000
+#define OCR_VOLTAGE_MASK 0x007FFF80
+#define OCR_ACCESS_MODE 0x60000000
+
+#define SECURE_ERASE 0x80000000
+
+#define MMC_STATUS_MASK (~0x0206BF7F)
+#define MMC_STATUS_RDY_FOR_DATA (1 << 8)
+#define MMC_STATUS_CURR_STATE (0xf << 9)
+#define MMC_STATUS_ERROR (1 << 19)
+
+#define MMC_STATE_PRG (7 << 9)
+
+#define MMC_VDD_165_195 0x00000080 /* VDD voltage 1.65 - 1.95 */
+#define MMC_VDD_20_21 0x00000100 /* VDD voltage 2.0 ~ 2.1 */
+#define MMC_VDD_21_22 0x00000200 /* VDD voltage 2.1 ~ 2.2 */
+#define MMC_VDD_22_23 0x00000400 /* VDD voltage 2.2 ~ 2.3 */
+#define MMC_VDD_23_24 0x00000800 /* VDD voltage 2.3 ~ 2.4 */
+#define MMC_VDD_24_25 0x00001000 /* VDD voltage 2.4 ~ 2.5 */
+#define MMC_VDD_25_26 0x00002000 /* VDD voltage 2.5 ~ 2.6 */
+#define MMC_VDD_26_27 0x00004000 /* VDD voltage 2.6 ~ 2.7 */
+#define MMC_VDD_27_28 0x00008000 /* VDD voltage 2.7 ~ 2.8 */
+#define MMC_VDD_28_29 0x00010000 /* VDD voltage 2.8 ~ 2.9 */
+#define MMC_VDD_29_30 0x00020000 /* VDD voltage 2.9 ~ 3.0 */
+#define MMC_VDD_30_31 0x00040000 /* VDD voltage 3.0 ~ 3.1 */
+#define MMC_VDD_31_32 0x00080000 /* VDD voltage 3.1 ~ 3.2 */
+#define MMC_VDD_32_33 0x00100000 /* VDD voltage 3.2 ~ 3.3 */
+#define MMC_VDD_33_34 0x00200000 /* VDD voltage 3.3 ~ 3.4 */
+#define MMC_VDD_34_35 0x00400000 /* VDD voltage 3.4 ~ 3.5 */
+#define MMC_VDD_35_36 0x00800000 /* VDD voltage 3.5 ~ 3.6 */
+
+#define MMC_SWITCH_MODE_CMD_SET 0x00 /* Change the command set */
+#define MMC_SWITCH_MODE_SET_BITS 0x01 /* Set bits in EXT_CSD byte
+ addressed by index which are
+ 1 in value field */
+#define MMC_SWITCH_MODE_CLEAR_BITS 0x02 /* Clear bits in EXT_CSD byte
+ addressed by index, which are
+ 1 in value field */
+#define MMC_SWITCH_MODE_WRITE_BYTE 0x03 /* Set target byte to value */
+
+#define SD_SWITCH_CHECK 0
+#define SD_SWITCH_SWITCH 1
+
+/*
+ * EXT_CSD fields
+ */
+#define EXT_CSD_GP_SIZE_MULT 143 /* R/W */
+#define EXT_CSD_PARTITIONS_ATTRIBUTE 156 /* R/W */
+#define EXT_CSD_PARTITIONING_SUPPORT 160 /* RO */
+#define EXT_CSD_RST_N_FUNCTION 162 /* R/W */
+#define EXT_CSD_RPMB_MULT 168 /* RO */
+#define EXT_CSD_ERASE_GROUP_DEF 175 /* R/W */
+#define EXT_CSD_BOOT_BUS_WIDTH 177
+#define EXT_CSD_PART_CONF 179 /* R/W */
+#define EXT_CSD_BUS_WIDTH 183 /* R/W */
+#define EXT_CSD_HS_TIMING 185 /* R/W */
+#define EXT_CSD_REV 192 /* RO */
+#define EXT_CSD_CARD_TYPE 196 /* RO */
+#define EXT_CSD_SEC_CNT 212 /* RO, 4 bytes */
+#define EXT_CSD_HC_WP_GRP_SIZE 221 /* RO */
+#define EXT_CSD_HC_ERASE_GRP_SIZE 224 /* RO */
+#define EXT_CSD_BOOT_MULT 226 /* RO */
+
+/*
+ * EXT_CSD field definitions
+ */
+
+#define EXT_CSD_CMD_SET_NORMAL (1 << 0)
+#define EXT_CSD_CMD_SET_SECURE (1 << 1)
+#define EXT_CSD_CMD_SET_CPSECURE (1 << 2)
+
+#define EXT_CSD_CARD_TYPE_26 (1 << 0) /* Card can run at 26MHz */
+#define EXT_CSD_CARD_TYPE_52 (1 << 1) /* Card can run at 52MHz */
+
+#define EXT_CSD_BUS_WIDTH_1 0 /* Card is in 1 bit mode */
+#define EXT_CSD_BUS_WIDTH_4 1 /* Card is in 4 bit mode */
+#define EXT_CSD_BUS_WIDTH_8 2 /* Card is in 8 bit mode */
+
+#define EXT_CSD_BOOT_ACK_ENABLE (1 << 6)
+#define EXT_CSD_BOOT_PARTITION_ENABLE (1 << 3)
+#define EXT_CSD_PARTITION_ACCESS_ENABLE (1 << 0)
+#define EXT_CSD_PARTITION_ACCESS_DISABLE (0 << 0)
+
+#define EXT_CSD_BOOT_ACK(x) (x << 6)
+#define EXT_CSD_BOOT_PART_NUM(x) (x << 3)
+#define EXT_CSD_PARTITION_ACCESS(x) (x << 0)
+
+#define EXT_CSD_BOOT_BUS_WIDTH_MODE(x) (x << 3)
+#define EXT_CSD_BOOT_BUS_WIDTH_RESET(x) (x << 2)
+#define EXT_CSD_BOOT_BUS_WIDTH_WIDTH(x) (x)
+
+#define R1_ILLEGAL_COMMAND (1 << 22)
+#define R1_APP_CMD (1 << 5)
+
+#define MMC_RSP_PRESENT (1 << 0)
+#define MMC_RSP_136 (1 << 1) /* 136 bit response */
+#define MMC_RSP_CRC (1 << 2) /* expect valid crc */
+#define MMC_RSP_BUSY (1 << 3) /* card may send busy */
+#define MMC_RSP_OPCODE (1 << 4) /* response contains opcode */
+
+#define MMC_RSP_NONE (0)
+#define MMC_RSP_R1 (MMC_RSP_PRESENT|MMC_RSP_CRC|MMC_RSP_OPCODE)
+#define MMC_RSP_R1b (MMC_RSP_PRESENT|MMC_RSP_CRC|MMC_RSP_OPCODE| \
+ MMC_RSP_BUSY)
+#define MMC_RSP_R2 (MMC_RSP_PRESENT|MMC_RSP_136|MMC_RSP_CRC)
+#define MMC_RSP_R3 (MMC_RSP_PRESENT)
+#define MMC_RSP_R4 (MMC_RSP_PRESENT)
+#define MMC_RSP_R5 (MMC_RSP_PRESENT|MMC_RSP_CRC|MMC_RSP_OPCODE)
+#define MMC_RSP_R6 (MMC_RSP_PRESENT|MMC_RSP_CRC|MMC_RSP_OPCODE)
+#define MMC_RSP_R7 (MMC_RSP_PRESENT|MMC_RSP_CRC|MMC_RSP_OPCODE)
+
+#define MMCPART_NOAVAILABLE (0xff)
+#define PART_ACCESS_MASK (0x7)
+#define PART_SUPPORT (0x1)
+#define PART_ENH_ATTRIB (0x1f)
+
+/* Maximum block size for MMC */
+#define MMC_MAX_BLOCK_LEN 512
+
+/* The number of MMC physical partitions. These consist of:
+ * boot partitions (2), general purpose partitions (4) in MMC v4.4.
+ */
+#define MMC_NUM_BOOT_PARTITION 2
+
+struct mmc_cid {
+ unsigned long psn;
+ unsigned short oid;
+ unsigned char mid;
+ unsigned char prv;
+ unsigned char mdt;
+ char pnm[7];
+};
+
+struct mmc_cmd {
+ ushort cmdidx;
+ uint resp_type;
+ uint cmdarg;
+ uint response[4];
+};
+
+struct mmc_data {
+ union {
+ char *dest;
+ const char *src; /* src buffers don't get written to */
+ };
+ uint flags;
+ uint blocks;
+ uint blocksize;
+};
+
+/* forward decl. */
+struct mmc;
+
+struct mmc_ops {
+ int (*send_cmd)(struct mmc *mmc,
+ struct mmc_cmd *cmd, struct mmc_data *data);
+ void (*set_ios)(struct mmc *mmc);
+ int (*init)(struct mmc *mmc);
+ int (*getcd)(struct mmc *mmc);
+ int (*getwp)(struct mmc *mmc);
+};
+
+struct mmc_config {
+ const char *name;
+ const struct mmc_ops *ops;
+ uint host_caps;
+ uint voltages;
+ uint f_min;
+ uint f_max;
+ uint b_max;
+ unsigned char part_type;
+};
+
+/* TODO struct mmc should be in mmc_private but it's hard to fix right now */
+struct mmc {
+ struct list_head link;
+ const struct mmc_config *cfg; /* provided configuration */
+ uint version;
+ void *priv;
+ uint has_init;
+ int high_capacity;
+ uint bus_width;
+ uint clock;
+ uint card_caps;
+ uint ocr;
+ uint dsr;
+ uint dsr_imp;
+ uint scr[2];
+ uint csd[4];
+ uint cid[4];
+ ushort rca;
+ char part_config;
+ char part_num;
+ uint tran_speed;
+ uint read_bl_len;
+ uint write_bl_len;
+ uint erase_grp_size;
+ u64 capacity;
+ u64 capacity_user;
+ u64 capacity_boot;
+ u64 capacity_rpmb;
+ u64 capacity_gp[4];
+ block_dev_desc_t block_dev;
+ char op_cond_pending; /* 1 if we are waiting on an op_cond command */
+ char init_in_progress; /* 1 if we have done mmc_start_init() */
+ char preinit; /* start init as early as possible */
+ uint op_cond_response; /* the response byte from the last op_cond */
+};
+
+int mmc_register(struct mmc *mmc);
+struct mmc *mmc_create(const struct mmc_config *cfg, void *priv);
+void mmc_destroy(struct mmc *mmc);
+int mmc_initialize(bd_t *bis);
+int mmc_init(struct mmc *mmc);
+int mmc_read(struct mmc *mmc, u64 src, uchar *dst, int size);
+void mmc_set_clock(struct mmc *mmc, uint clock);
+struct mmc *find_mmc_device(int dev_num);
+int mmc_set_dev(int dev_num);
+void print_mmc_devices(char separator);
+int get_mmc_num(void);
+int board_mmc_getcd(struct mmc *mmc);
+int mmc_switch_part(int dev_num, unsigned int part_num);
+int mmc_getcd(struct mmc *mmc);
+int mmc_getwp(struct mmc *mmc);
+int mmc_set_dsr(struct mmc *mmc, u16 val);
+/* Function to change the size of boot partition and rpmb partitions */
+int mmc_boot_partition_size_change(struct mmc *mmc, unsigned long bootsize,
+ unsigned long rpmbsize);
+/* Function to modify the PARTITION_CONFIG field of EXT_CSD */
+int mmc_set_part_conf(struct mmc *mmc, u8 ack, u8 part_num, u8 access);
+/* Function to modify the BOOT_BUS_WIDTH field of EXT_CSD */
+int mmc_set_boot_bus_width(struct mmc *mmc, u8 width, u8 reset, u8 mode);
+/* Function to modify the RST_n_FUNCTION field of EXT_CSD */
+int mmc_set_rst_n_function(struct mmc *mmc, u8 enable);
+
+/**
+ * Start device initialization and return immediately; it does not block on
+ * polling OCR (operation condition register) status. Then you should call
+ * mmc_init, which would block on polling OCR status and complete the device
+ * initializatin.
+ *
+ * @param mmc Pointer to a MMC device struct
+ * @return 0 on success, IN_PROGRESS on waiting for OCR status, <0 on error.
+ */
+int mmc_start_init(struct mmc *mmc);
+
+/**
+ * Set preinit flag of mmc device.
+ *
+ * This will cause the device to be pre-inited during mmc_initialize(),
+ * which may save boot time if the device is not accessed until later.
+ * Some eMMC devices take 200-300ms to init, but unfortunately they
+ * must be sent a series of commands to even get them to start preparing
+ * for operation.
+ *
+ * @param mmc Pointer to a MMC device struct
+ * @param preinit preinit flag value
+ */
+void mmc_set_preinit(struct mmc *mmc, int preinit);
+
+#ifdef CONFIG_GENERIC_MMC
+#ifdef CONFIG_MMC_SPI
+#define mmc_host_is_spi(mmc) ((mmc)->cfg->host_caps & MMC_MODE_SPI)
+#else
+#define mmc_host_is_spi(mmc) 0
+#endif
+struct mmc *mmc_spi_init(uint bus, uint cs, uint speed, uint mode);
+#else
+int mmc_legacy_init(int verbose);
+#endif
+
+int board_mmc_init(bd_t *bis);
+
+/* Set block count limit because of 16 bit register limit on some hardware*/
+#ifndef CONFIG_SYS_MMC_MAX_BLK_COUNT
+#define CONFIG_SYS_MMC_MAX_BLK_COUNT 65535
+#endif
+
+#endif /* _MMC_H_ */
Code Review / kvmfornfv.git / blobdiff