--- /dev/null
+/*
+ * This is used to for host and peripheral modes of the driver for
+ * Inventra (Multidrop) Highspeed Dual-Role Controllers: (M)HDRC.
+ *
+ * Board initialization should put one of these into dev->platform_data,
+ * probably on some platform_device named "musb-hdrc". It encapsulates
+ * key configuration differences between boards.
+ */
+
+#ifndef __LINUX_USB_MUSB_H
+#define __LINUX_USB_MUSB_H
+
+#ifndef __deprecated
+#define __deprecated
+#endif
+
+/* The USB role is defined by the connector used on the board, so long as
+ * standards are being followed. (Developer boards sometimes won't.)
+ */
+enum musb_mode {
+ MUSB_UNDEFINED = 0,
+ MUSB_HOST, /* A or Mini-A connector */
+ MUSB_PERIPHERAL, /* B or Mini-B connector */
+ MUSB_OTG /* Mini-AB connector */
+};
+
+struct clk;
+
+enum musb_fifo_style {
+ FIFO_RXTX,
+ FIFO_TX,
+ FIFO_RX
+} __attribute__ ((packed));
+
+enum musb_buf_mode {
+ BUF_SINGLE,
+ BUF_DOUBLE
+} __attribute__ ((packed));
+
+struct musb_fifo_cfg {
+ u8 hw_ep_num;
+ enum musb_fifo_style style;
+ enum musb_buf_mode mode;
+ u16 maxpacket;
+};
+
+#define MUSB_EP_FIFO(ep, st, m, pkt) \
+{ \
+ .hw_ep_num = ep, \
+ .style = st, \
+ .mode = m, \
+ .maxpacket = pkt, \
+}
+
+#define MUSB_EP_FIFO_SINGLE(ep, st, pkt) \
+ MUSB_EP_FIFO(ep, st, BUF_SINGLE, pkt)
+
+#define MUSB_EP_FIFO_DOUBLE(ep, st, pkt) \
+ MUSB_EP_FIFO(ep, st, BUF_DOUBLE, pkt)
+
+struct musb_hdrc_eps_bits {
+ const char name[16];
+ u8 bits;
+};
+
+struct musb_hdrc_config {
+ struct musb_fifo_cfg *fifo_cfg; /* board fifo configuration */
+ unsigned fifo_cfg_size; /* size of the fifo configuration */
+
+ /* MUSB configuration-specific details */
+ unsigned multipoint:1; /* multipoint device */
+ unsigned dyn_fifo:1 __deprecated; /* supports dynamic fifo sizing */
+ unsigned soft_con:1 __deprecated; /* soft connect required */
+ unsigned utm_16:1 __deprecated; /* utm data witdh is 16 bits */
+ unsigned big_endian:1; /* true if CPU uses big-endian */
+ unsigned mult_bulk_tx:1; /* Tx ep required for multbulk pkts */
+ unsigned mult_bulk_rx:1; /* Rx ep required for multbulk pkts */
+ unsigned high_iso_tx:1; /* Tx ep required for HB iso */
+ unsigned high_iso_rx:1; /* Rx ep required for HD iso */
+ unsigned dma:1 __deprecated; /* supports DMA */
+ unsigned vendor_req:1 __deprecated; /* vendor registers required */
+
+ u8 num_eps; /* number of endpoints _with_ ep0 */
+ u8 dma_channels __deprecated; /* number of dma channels */
+ u8 dyn_fifo_size; /* dynamic size in bytes */
+ u8 vendor_ctrl __deprecated; /* vendor control reg width */
+ u8 vendor_stat __deprecated; /* vendor status reg witdh */
+ u8 dma_req_chan __deprecated; /* bitmask for required dma channels */
+ u8 ram_bits; /* ram address size */
+
+ struct musb_hdrc_eps_bits *eps_bits __deprecated;
+#ifdef CONFIG_BLACKFIN
+ /* A GPIO controlling VRSEL in Blackfin */
+ unsigned int gpio_vrsel;
+ unsigned int gpio_vrsel_active;
+ /* musb CLKIN in Blackfin in MHZ */
+ unsigned char clkin;
+#endif
+
+};
+
+struct musb_hdrc_platform_data {
+ /* MUSB_HOST, MUSB_PERIPHERAL, or MUSB_OTG */
+ u8 mode;
+
+ /* for clk_get() */
+ const char *clock;
+
+ /* (HOST or OTG) switch VBUS on/off */
+ int (*set_vbus)(struct device *dev, int is_on);
+
+ /* (HOST or OTG) mA/2 power supplied on (default = 8mA) */
+ u8 power;
+
+ /* (PERIPHERAL) mA/2 max power consumed (default = 100mA) */
+ u8 min_power;
+
+ /* (HOST or OTG) msec/2 after VBUS on till power good */
+ u8 potpgt;
+
+ /* (HOST or OTG) program PHY for external Vbus */
+ unsigned extvbus:1;
+
+ /* Power the device on or off */
+ int (*set_power)(int state);
+
+ /* MUSB configuration-specific details */
+ struct musb_hdrc_config *config;
+
+ /* Architecture specific board data */
+ void *board_data;
+
+ /* Platform specific struct musb_ops pointer */
+ const void *platform_ops;
+};
+
+
+/* TUSB 6010 support */
+
+#define TUSB6010_OSCCLK_60 16667 /* psec/clk @ 60.0 MHz */
+#define TUSB6010_REFCLK_24 41667 /* psec/clk @ 24.0 MHz XI */
+#define TUSB6010_REFCLK_19 52083 /* psec/clk @ 19.2 MHz CLKIN */
+
+#ifdef CONFIG_ARCH_OMAP2
+
+extern int __init tusb6010_setup_interface(
+ struct musb_hdrc_platform_data *data,
+ unsigned ps_refclk, unsigned waitpin,
+ unsigned async_cs, unsigned sync_cs,
+ unsigned irq, unsigned dmachan);
+
+extern int tusb6010_platform_retime(unsigned is_refclk);
+
+#endif /* OMAP2 */
+
+/*
+ * U-Boot specfic stuff
+ */
+int musb_register(struct musb_hdrc_platform_data *plat, void *bdata,
+ void *ctl_regs);
+
+#endif /* __LINUX_USB_MUSB_H */
Code Review / kvmfornfv.git / blobdiff