--- /dev/null
+/*
+ * (C) Copyright 2012 Michal Simek <monstr@monstr.eu>
+ * (C) Copyright 2013 Xilinx, Inc.
+ *
+ * Common configuration options for all Zynq boards.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __CONFIG_ZYNQ_COMMON_H
+#define __CONFIG_ZYNQ_COMMON_H
+
+/* High Level configuration Options */
+#define CONFIG_ARMV7
+#define CONFIG_ZYNQ
+
+/* CPU clock */
+#ifndef CONFIG_CPU_FREQ_HZ
+# define CONFIG_CPU_FREQ_HZ 800000000
+#endif
+
+/* Cache options */
+#define CONFIG_CMD_CACHE
+#define CONFIG_SYS_CACHELINE_SIZE 32
+
+#define CONFIG_SYS_L2CACHE_OFF
+#ifndef CONFIG_SYS_L2CACHE_OFF
+# define CONFIG_SYS_L2_PL310
+# define CONFIG_SYS_PL310_BASE 0xf8f02000
+#endif
+
+/* Serial drivers */
+#define CONFIG_BAUDRATE 115200
+/* The following table includes the supported baudrates */
+#define CONFIG_SYS_BAUDRATE_TABLE \
+ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400}
+
+/* DCC driver */
+#if defined(CONFIG_ZYNQ_DCC)
+# define CONFIG_ARM_DCC
+# define CONFIG_CPU_V6 /* Required by CONFIG_ARM_DCC */
+#else
+# define CONFIG_ZYNQ_SERIAL
+#endif
+
+/* Ethernet driver */
+#if defined(CONFIG_ZYNQ_GEM0) || defined(CONFIG_ZYNQ_GEM1)
+# define CONFIG_NET_MULTI
+# define CONFIG_ZYNQ_GEM
+# define CONFIG_MII
+# define CONFIG_SYS_FAULT_ECHO_LINK_DOWN
+# define CONFIG_PHYLIB
+# define CONFIG_PHY_MARVELL
+#endif
+
+/* SPI */
+#ifdef CONFIG_ZYNQ_SPI
+# define CONFIG_SPI_FLASH
+# define CONFIG_SPI_FLASH_SST
+# define CONFIG_CMD_SF
+#endif
+
+/* NOR */
+#ifndef CONFIG_SYS_NO_FLASH
+# define CONFIG_SYS_FLASH_BASE 0xE2000000
+# define CONFIG_SYS_FLASH_SIZE (16 * 1024 * 1024)
+# define CONFIG_SYS_MAX_FLASH_BANKS 1
+# define CONFIG_SYS_MAX_FLASH_SECT 512
+# define CONFIG_SYS_FLASH_ERASE_TOUT 1000
+# define CONFIG_SYS_FLASH_WRITE_TOUT 5000
+# define CONFIG_FLASH_SHOW_PROGRESS 10
+# define CONFIG_SYS_FLASH_CFI
+# undef CONFIG_SYS_FLASH_EMPTY_INFO
+# define CONFIG_FLASH_CFI_DRIVER
+# undef CONFIG_SYS_FLASH_PROTECTION
+# define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
+#endif
+
+/* MMC */
+#if defined(CONFIG_ZYNQ_SDHCI0) || defined(CONFIG_ZYNQ_SDHCI1)
+# define CONFIG_MMC
+# define CONFIG_GENERIC_MMC
+# define CONFIG_SDHCI
+# define CONFIG_ZYNQ_SDHCI
+# define CONFIG_CMD_MMC
+# define CONFIG_CMD_FAT
+# define CONFIG_SUPPORT_VFAT
+# define CONFIG_CMD_EXT2
+# define CONFIG_DOS_PARTITION
+#endif
+
+#define CONFIG_SYS_I2C_ZYNQ
+/* I2C */
+#if defined(CONFIG_SYS_I2C_ZYNQ)
+# define CONFIG_CMD_I2C
+# define CONFIG_SYS_I2C
+# define CONFIG_SYS_I2C_ZYNQ_SPEED 100000
+# define CONFIG_SYS_I2C_ZYNQ_SLAVE 0
+#endif
+
+/* EEPROM */
+#ifdef CONFIG_ZYNQ_EEPROM
+# define CONFIG_CMD_EEPROM
+# define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
+# define CONFIG_SYS_I2C_EEPROM_ADDR 0x54
+# define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4
+# define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5
+# define CONFIG_SYS_EEPROM_SIZE 1024 /* Bytes */
+#endif
+
+#define CONFIG_BOOTP_SERVERIP
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+#define CONFIG_BOOTP_MAY_FAIL
+
+/* Total Size of Environment Sector */
+#define CONFIG_ENV_SIZE (128 << 10)
+
+/* Allow to overwrite serial and ethaddr */
+#define CONFIG_ENV_OVERWRITE
+
+/* Environment */
+#ifndef CONFIG_ENV_IS_NOWHERE
+# ifndef CONFIG_SYS_NO_FLASH
+# define CONFIG_ENV_IS_IN_FLASH
+# elif defined(CONFIG_SYS_NO_FLASH)
+# define CONFIG_ENV_IS_NOWHERE
+# endif
+
+# define CONFIG_ENV_SECT_SIZE CONFIG_ENV_SIZE
+# define CONFIG_ENV_OFFSET 0xE0000
+# define CONFIG_CMD_SAVEENV
+#endif
+
+/* Default environment */
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "fit_image=fit.itb\0" \
+ "load_addr=0x2000000\0" \
+ "fit_size=0x800000\0" \
+ "flash_off=0x100000\0" \
+ "nor_flash_off=0xE2100000\0" \
+ "fdt_high=0x20000000\0" \
+ "initrd_high=0x20000000\0" \
+ "norboot=echo Copying FIT from NOR flash to RAM... && " \
+ "cp.b ${nor_flash_off} ${load_addr} ${fit_size} && " \
+ "bootm ${load_addr}\0" \
+ "sdboot=echo Copying FIT from SD to RAM... && " \
+ "fatload mmc 0 ${load_addr} ${fit_image} && " \
+ "bootm ${load_addr}\0" \
+ "jtagboot=echo TFTPing FIT to RAM... && " \
+ "tftpboot ${load_addr} ${fit_image} && " \
+ "bootm ${load_addr}\0"
+#define CONFIG_BOOTCOMMAND "run $modeboot"
+#define CONFIG_BOOTDELAY 3 /* -1 to Disable autoboot */
+#define CONFIG_SYS_LOAD_ADDR 0 /* default? */
+
+/* Miscellaneous configurable options */
+#define CONFIG_SYS_PROMPT "zynq-uboot> "
+#define CONFIG_SYS_HUSH_PARSER
+
+#define CONFIG_CMDLINE_EDITING
+#define CONFIG_AUTO_COMPLETE
+#define CONFIG_BOARD_LATE_INIT
+#define CONFIG_SYS_LONGHELP
+#define CONFIG_CLOCKS
+#define CONFIG_CMD_CLK
+#define CONFIG_SYS_MAXARGS 15 /* max number of command args */
+#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
+ sizeof(CONFIG_SYS_PROMPT) + 16)
+
+/* Physical Memory map */
+#define CONFIG_SYS_TEXT_BASE 0x4000000
+
+#define CONFIG_NR_DRAM_BANKS 1
+#define CONFIG_SYS_SDRAM_BASE 0
+
+#define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE
+#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_SDRAM_BASE + 0x1000)
+
+#define CONFIG_SYS_MALLOC_LEN 0x400000
+#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_SDRAM_BASE
+#define CONFIG_SYS_INIT_RAM_SIZE CONFIG_SYS_MALLOC_LEN
+#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + \
+ CONFIG_SYS_INIT_RAM_SIZE - \
+ GENERATED_GBL_DATA_SIZE)
+
+/* Enable the PL to be downloaded */
+#define CONFIG_FPGA
+#define CONFIG_FPGA_XILINX
+#define CONFIG_FPGA_ZYNQPL
+#define CONFIG_CMD_FPGA
+
+/* Open Firmware flat tree */
+#define CONFIG_OF_LIBFDT
+
+/* FIT support */
+#define CONFIG_FIT
+#define CONFIG_FIT_VERBOSE 1 /* enable fit_format_{error,warning}() */
+
+/* FDT support */
+#define CONFIG_OF_CONTROL
+#define CONFIG_OF_SEPARATE
+#define CONFIG_DISPLAY_BOARDINFO_LATE
+
+/* RSA support */
+#define CONFIG_FIT_SIGNATURE
+#define CONFIG_RSA
+
+/* Extend size of kernel image for uncompression */
+#define CONFIG_SYS_BOOTM_LEN (20 * 1024 * 1024)
+
+/* Boot FreeBSD/vxWorks from an ELF image */
+#if defined(CONFIG_ZYNQ_BOOT_FREEBSD)
+# define CONFIG_API
+# define CONFIG_CMD_ELF
+# define CONFIG_SYS_MMC_MAX_DEVICE 1
+#endif
+
+#define CONFIG_SYS_LDSCRIPT "arch/arm/cpu/armv7/zynq/u-boot.lds"
+
+/* Commands */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_TFTPPUT
+
+/* SPL part */
+#define CONFIG_SPL
+#define CONFIG_CMD_SPL
+#define CONFIG_SPL_FRAMEWORK
+#define CONFIG_SPL_LIBCOMMON_SUPPORT
+#define CONFIG_SPL_LIBGENERIC_SUPPORT
+#define CONFIG_SPL_SERIAL_SUPPORT
+
+#define CONFIG_SPL_LDSCRIPT "arch/arm/cpu/armv7/zynq/u-boot-spl.lds"
+
+/* Disable dcache for SPL just for sure */
+#ifdef CONFIG_SPL_BUILD
+#define CONFIG_SYS_DCACHE_OFF
+#undef CONFIG_FPGA
+#undef CONFIG_OF_CONTROL
+#endif
+
+/* MMC support */
+#ifdef CONFIG_ZYNQ_SDHCI0
+#define CONFIG_SPL_MMC_SUPPORT
+#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x300 /* address 0x60000 */
+#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x200 /* 256 KB */
+#define CONFIG_SYS_MMC_SD_FAT_BOOT_PARTITION 1
+#define CONFIG_SPL_LIBDISK_SUPPORT
+#define CONFIG_SPL_FAT_SUPPORT
+#define CONFIG_SPL_FAT_LOAD_PAYLOAD_NAME "u-boot.img"
+#endif
+
+/* Address in RAM where the parameters must be copied by SPL. */
+#define CONFIG_SYS_SPL_ARGS_ADDR 0x10000000
+
+#define CONFIG_SPL_FAT_LOAD_ARGS_NAME "system.dtb"
+#define CONFIG_SPL_FAT_LOAD_KERNEL_NAME "uImage"
+
+/* Not using MMC raw mode - just for compilation purpose */
+#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR 0
+#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS 0
+#define CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR 0
+
+/* qspi mode is working fine */
+#ifdef CONFIG_ZYNQ_QSPI
+#define CONFIG_SPL_SPI_SUPPORT
+#define CONFIG_SPL_SPI_LOAD
+#define CONFIG_SPL_SPI_FLASH_SUPPORT
+#define CONFIG_SPL_SPI_BUS 0
+#define CONFIG_SYS_SPI_U_BOOT_OFFS 0x100000
+#define CONFIG_SPL_SPI_CS 0
+#endif
+
+/* for booting directly linux */
+#define CONFIG_SPL_OS_BOOT
+
+/* SP location before relocation, must use scratch RAM */
+#define CONFIG_SPL_TEXT_BASE 0x0
+
+/* 3 * 64kB blocks of OCM - one is on the top because of bootrom */
+#define CONFIG_SPL_MAX_SIZE 0x30000
+
+/* The highest 64k OCM address */
+#define OCM_HIGH_ADDR 0xffff0000
+
+/* Just define any reasonable size */
+#define CONFIG_SPL_STACK_SIZE 0x1000
+
+/* SPL stack position - and stack goes down */
+#define CONFIG_SPL_STACK (OCM_HIGH_ADDR + CONFIG_SPL_STACK_SIZE)
+
+/* On the top of OCM space */
+#define CONFIG_SYS_SPL_MALLOC_START (CONFIG_SPL_STACK + \
+ GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_SPL_MALLOC_SIZE 0x1000
+
+/* BSS setup */
+#define CONFIG_SPL_BSS_START_ADDR 0x100000
+#define CONFIG_SPL_BSS_MAX_SIZE 0x100000
+
+#define CONFIG_SYS_UBOOT_START CONFIG_SYS_TEXT_BASE
+
+#endif /* __CONFIG_ZYNQ_COMMON_H */
Code Review / kvmfornfv.git / blobdiff