--- /dev/null
+/*
+ * (C) Copyright 2007
+ * Stefan Roese, DENX Software Engineering, sr@denx.de.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+/************************************************************************
+ * zeus.h - configuration for Zeus board
+ ***********************************************************************/
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*-----------------------------------------------------------------------
+ * High Level Configuration Options
+ *----------------------------------------------------------------------*/
+#define CONFIG_ZEUS 1 /* Board is Zeus */
+#define CONFIG_405EP 1 /* Specifc 405EP support*/
+
+#define CONFIG_SYS_TEXT_BASE 0xFFFC0000
+
+#define CONFIG_SYS_CLK_FREQ 33000000 /* external frequency to pll */
+
+#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
+#define CONFIG_MISC_INIT_R 1 /* Call misc_init_r */
+
+#define PLLMR0_DEFAULT PLLMR0_333_111_55_111
+#define PLLMR1_DEFAULT PLLMR1_333_111_55_111
+
+#define CONFIG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */
+
+#define CONFIG_OVERWRITE_ETHADDR_ONCE 1
+
+#define CONFIG_PPC4xx_EMAC
+#define CONFIG_MII 1 /* MII PHY management */
+#define CONFIG_PHY_ADDR 0x01 /* PHY address */
+#define CONFIG_HAS_ETH1 1
+#define CONFIG_PHY1_ADDR 0x11 /* EMAC1 PHY address */
+#define CONFIG_SYS_RX_ETH_BUFFER 16 /* Number of ethernet rx buffers & descriptors */
+#define CONFIG_PHY_RESET 1
+#define CONFIG_PHY_RESET_DELAY 300 /* PHY RESET recovery delay */
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_ASKENV
+#define CONFIG_CMD_CACHE
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_DIAG
+#define CONFIG_CMD_EEPROM
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_IRQ
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_NFS
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_REGINFO
+
+/* POST support */
+#define CONFIG_POST (CONFIG_SYS_POST_MEMORY | \
+ CONFIG_SYS_POST_CPU | \
+ CONFIG_SYS_POST_CACHE | \
+ CONFIG_SYS_POST_UART | \
+ CONFIG_SYS_POST_ETHER)
+
+#define CONFIG_SYS_POST_ETHER_EXT_LOOPBACK /* eth POST using ext loopack connector */
+
+/* Define here the base-addresses of the UARTs to test in POST */
+#define CONFIG_SYS_POST_UART_TABLE { CONFIG_SYS_NS16550_COM1 }
+
+#define CONFIG_LOGBUFFER
+#define CONFIG_SYS_POST_CACHE_ADDR 0x00800000 /* free virtual address */
+
+#define CONFIG_SYS_CONSOLE_IS_IN_ENV /* Otherwise it catches logbuffer as output */
+
+#undef CONFIG_WATCHDOG /* watchdog disabled */
+
+/*-----------------------------------------------------------------------
+ * SDRAM
+ *----------------------------------------------------------------------*/
+/*
+ * SDRAM configuration (please see cpu/ppc/sdram.[ch])
+ */
+#define CONFIG_SDRAM_BANK0 1 /* init onboard SDRAM bank 0 */
+#define CONFIG_SDRAM_BANK1 1 /* init onboard SDRAM bank 1 */
+
+/* SDRAM timings used in datasheet */
+#define CONFIG_SYS_SDRAM_CL 3 /* CAS latency */
+#define CONFIG_SYS_SDRAM_tRP 20 /* PRECHARGE command period */
+#define CONFIG_SYS_SDRAM_tRC 66 /* ACTIVE-to-ACTIVE command period */
+#define CONFIG_SYS_SDRAM_tRCD 20 /* ACTIVE-to-READ delay */
+#define CONFIG_SYS_SDRAM_tRFC 66 /* Auto refresh period */
+
+/*-----------------------------------------------------------------------
+ * Serial Port
+ *----------------------------------------------------------------------*/
+#define CONFIG_CONS_INDEX 1
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE 1
+#define CONFIG_SYS_NS16550_CLK get_serial_clock()
+#undef CONFIG_SYS_EXT_SERIAL_CLOCK /* external serial clock */
+#define CONFIG_SYS_BASE_BAUD 691200
+#define CONFIG_BAUDRATE 115200
+
+#define CONFIG_SYS_BAUDRATE_TABLE \
+ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400}
+
+/*-----------------------------------------------------------------------
+ * Miscellaneous configurable options
+ *----------------------------------------------------------------------*/
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#if defined(CONFIG_CMD_KGDB)
+#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
+#else
+#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
+#endif
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
+
+#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */
+#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
+
+#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
+#define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_into (bd_t) */
+
+#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
+#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
+
+#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
+#define CONFIG_LOOPW 1 /* enable loopw command */
+#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */
+#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
+#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
+
+/*-----------------------------------------------------------------------
+ * I2C
+ *----------------------------------------------------------------------*/
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_PPC4XX
+#define CONFIG_SYS_I2C_PPC4XX_CH0
+#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000
+#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F
+
+/* these are for the ST M24C02 2kbit serial i2c eeprom */
+#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* base address */
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* bytes of address */
+/* mask of address bits that overflow into the "EEPROM chip address" */
+#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW 0x07
+
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 /* 8 byte write page size */
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */
+
+/*
+ * The layout of the I2C EEPROM, used for bootstrap setup and for board-
+ * specific values, like ethaddr... that can be restored via the sw-reset
+ * button
+ */
+#define FACTORY_RESET_I2C_EEPROM 0x50
+#define FACTORY_RESET_ENV_OFFS 0x80
+#define FACTORY_RESET_ENV_SIZE 0x80
+
+/*-----------------------------------------------------------------------
+ * Start addresses for the final memory configuration
+ * (Set up by the startup code)
+ * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
+ */
+#define CONFIG_SYS_SDRAM_BASE 0x00000000
+#define CONFIG_SYS_FLASH_BASE 0xFF000000
+#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Monitor */
+#define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc() */
+#define CONFIG_SYS_MONITOR_BASE (-CONFIG_SYS_MONITOR_LEN)
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+
+/*-----------------------------------------------------------------------
+ * FLASH organization
+ */
+#define CONFIG_SYS_FLASH_CFI /* The flash is CFI compatible */
+#define CONFIG_FLASH_CFI_DRIVER /* Use common CFI driver */
+
+#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE }
+
+#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
+#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max number of sectors on one chip */
+
+#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
+
+#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */
+#define CONFIG_SYS_FLASH_PROTECTION 1 /* use hardware flash protection */
+
+#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
+#define CONFIG_SYS_FLASH_QUIET_TEST 1 /* don't warn upon unknown flash */
+
+#ifdef CONFIG_ENV_IS_IN_FLASH
+#define CONFIG_ENV_SECT_SIZE 0x20000 /* size of one complete sector */
+#define CONFIG_ENV_ADDR ((-CONFIG_SYS_MONITOR_LEN)-CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */
+
+/* Address and size of Redundant Environment Sector */
+#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR-CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
+#endif
+
+/*-----------------------------------------------------------------------
+ * Definitions for initial stack pointer and data area (in data cache)
+ */
+/* use on chip memory (OCM) for temperary stack until sdram is tested */
+#define CONFIG_SYS_TEMP_STACK_OCM 1
+
+/* On Chip Memory location */
+#define CONFIG_SYS_OCM_DATA_ADDR 0xF8000000
+#define CONFIG_SYS_OCM_DATA_SIZE 0x1000
+#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_DATA_ADDR /* inside of OCM */
+#define CONFIG_SYS_INIT_RAM_SIZE CONFIG_SYS_OCM_DATA_SIZE /* Size of used area in RAM */
+
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+/* reserve some memory for POST and BOOT limit info */
+#define CONFIG_SYS_INIT_SP_OFFSET (CONFIG_SYS_GBL_DATA_OFFSET - 16)
+
+/* extra data in OCM */
+#define CONFIG_SYS_POST_MAGIC \
+ (CONFIG_SYS_OCM_DATA_ADDR + CONFIG_SYS_GBL_DATA_OFFSET - 8)
+#define CONFIG_SYS_POST_VAL \
+ (CONFIG_SYS_OCM_DATA_ADDR + CONFIG_SYS_GBL_DATA_OFFSET - 12)
+
+/*-----------------------------------------------------------------------
+ * External Bus Controller (EBC) Setup
+ */
+
+/* Memory Bank 0 (Flash 16M) initialization */
+#define CONFIG_SYS_EBC_PB0AP 0x05815600
+#define CONFIG_SYS_EBC_PB0CR 0xFF09A000 /* BAS=0xFF0,BS=16MB,BU=R/W,BW=16bit */
+
+/*-----------------------------------------------------------------------
+ * Definitions for GPIO setup (PPC405EP specific)
+ *
+ * GPIO0[0] - External Bus Controller BLAST output
+ * GPIO0[1-9] - Instruction trace outputs
+ * GPIO0[10-13] - External Bus Controller CS_1 - CS_4 outputs
+ * GPIO0[14-16] - External Bus Controller ABUS3-ABUS5 outputs
+ * GPIO0[17-23] - External Interrupts IRQ0 - IRQ6 inputs
+ * GPIO0[24-27] - UART0 control signal inputs/outputs
+ * GPIO0[28-29] - UART1 data signal input/output
+ * GPIO0[30-31] - EMAC0 and EMAC1 reject packet inputs
+ */
+#define CONFIG_SYS_GPIO0_OSRL 0x15555550 /* Chip selects */
+#define CONFIG_SYS_GPIO0_OSRH 0x00000110 /* UART_DTR-pin 27 alt out */
+#define CONFIG_SYS_GPIO0_ISR1L 0x10000041 /* Pin 2, 12 is input */
+#define CONFIG_SYS_GPIO0_ISR1H 0x15505440 /* OUT: LEDs 22/23; IN: pin12,2, NVALID# */
+#define CONFIG_SYS_GPIO0_TSRL 0x00000000
+#define CONFIG_SYS_GPIO0_TSRH 0x00000000
+#define CONFIG_SYS_GPIO0_TCR 0xBFF68317 /* 3-state OUT: 22/23/29; 12,2 is not 3-state */
+#define CONFIG_SYS_GPIO0_ODR 0x00000000
+
+#define CONFIG_SYS_GPIO_SW_RESET 1
+#define CONFIG_SYS_GPIO_ZEUS_PE 12
+#define CONFIG_SYS_GPIO_LED_RED 22
+#define CONFIG_SYS_GPIO_LED_GREEN 23
+
+/* Time in milli-seconds */
+#define CONFIG_SYS_TIME_POST 5000
+#define CONFIG_SYS_TIME_FACTORY_RESET 10000
+
+#if defined(CONFIG_CMD_KGDB)
+#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
+#endif
+
+/*
+ * Pass open firmware flat tree
+ */
+#define CONFIG_OF_LIBFDT
+#define CONFIG_OF_BOARD_SETUP
+
+/* ENVIRONMENT VARS */
+
+#define CONFIG_PREBOOT "echo;echo Welcome to Bulletendpoints board v1.1;echo"
+#define CONFIG_IPADDR 192.168.1.10
+#define CONFIG_SERVERIP 192.168.1.100
+#define CONFIG_GATEWAYIP 192.168.1.100
+#define CONFIG_ETHADDR 50:00:00:00:06:00
+#define CONFIG_ETH1ADDR 50:00:00:00:06:01
+#if 0
+#define CONFIG_BOOTDELAY -1 /* autoboot disabled */
+#else
+#define CONFIG_BOOTDELAY 3 /* autoboot after 5 seconds */
+#endif
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "logversion=2\0" \
+ "hostname=zeus\0" \
+ "netdev=eth0\0" \
+ "ethact=ppc_4xx_eth0\0" \
+ "netmask=255.255.255.0\0" \
+ "ramdisk_size=50000\0" \
+ "nfsargs=setenv bootargs root=/dev/nfs rw" \
+ " nfsroot=${serverip}:${rootpath}\0" \
+ "ramargs=setenv bootargs root=/dev/ram rw" \
+ " ramdisk_size=${ramdisk_size}\0" \
+ "addip=setenv bootargs ${bootargs} " \
+ "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
+ ":${hostname}:${netdev}:off panic=1\0" \
+ "addtty=setenv bootargs ${bootargs} console=ttyS0," \
+ "${baudrate}\0" \
+ "net_nfs=tftp ${kernel_mem_addr} ${file_kernel};" \
+ "run nfsargs addip addtty;bootm\0" \
+ "net_ram=tftp ${kernel_mem_addr} ${file_kernel};" \
+ "tftp ${ramdisk_mem_addr} ${file_fs};" \
+ "run ramargs addip addtty;" \
+ "bootm ${kernel_mem_addr} ${ramdisk_mem_addr}\0" \
+ "rootpath=/target_fs/zeus\0" \
+ "kernel_fl_addr=ff000000\0" \
+ "kernel_mem_addr=200000\0" \
+ "ramdisk_fl_addr=ff300000\0" \
+ "ramdisk_mem_addr=4000000\0" \
+ "uboot_fl_addr=fffc0000\0" \
+ "uboot_mem_addr=100000\0" \
+ "file_uboot=/zeus/u-boot.bin\0" \
+ "tftp_uboot=tftp 100000 ${file_uboot}\0" \
+ "update_uboot=protect off fffc0000 ffffffff;" \
+ "era fffc0000 ffffffff;cp.b 100000 fffc0000 40000;" \
+ "protect on fffc0000 ffffffff\0" \
+ "upd_uboot=run tftp_uboot;run update_uboot\0" \
+ "file_kernel=/zeus/uImage_ba\0" \
+ "tftp_kernel=tftp 100000 ${file_kernel}\0" \
+ "update_kernel=protect off ff000000 ff17ffff;" \
+ "era ff000000 ff17ffff;cp.b 100000 ff000000 180000\0" \
+ "upd_kernel=run tftp_kernel;run update_kernel\0" \
+ "file_fs=/zeus/rootfs_ba.img\0" \
+ "tftp_fs=tftp 100000 ${file_fs}\0" \
+ "update_fs=protect off ff300000 ff87ffff;era ff300000 ff87ffff;"\
+ "cp.b 100000 ff300000 580000\0" \
+ "upd_fs=run tftp_fs;run update_fs\0" \
+ "bootcmd=chkreset;run ramargs addip addtty addmisc;" \
+ "bootm ${kernel_fl_addr} ${ramdisk_fl_addr}\0" \
+ ""
+
+#endif /* __CONFIG_H */
Code Review / kvmfornfv.git / blobdiff