--- /dev/null
+/*
+ * (C) Copyright 2005-2007
+ * Stefan Roese, DENX Software Engineering, sr@denx.de.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+/************************************************************************
+ * yosemite.h - configuration for Yosemite & Yellowstone boards
+ ***********************************************************************/
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*-----------------------------------------------------------------------
+ * High Level Configuration Options
+ *----------------------------------------------------------------------*/
+/* This config file is used for Yosemite (440EP) and Yellowstone (440GR)*/
+#ifndef CONFIG_YELLOWSTONE
+#define CONFIG_440EP 1 /* Specific PPC440EP support */
+#define CONFIG_HOSTNAME yosemite
+#else
+#define CONFIG_440GR 1 /* Specific PPC440GR support */
+#define CONFIG_HOSTNAME yellowstone
+#endif
+#define CONFIG_440 1 /* ... PPC440 family */
+#define CONFIG_SYS_CLK_FREQ 66666666 /* external freq to pll */
+
+#define CONFIG_SYS_TEXT_BASE 0xFFF80000
+
+/*
+ * Include common defines/options for all AMCC eval boards
+ */
+#include "amcc-common.h"
+
+#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
+#define CONFIG_MISC_INIT_R 1 /* call misc_init_r() */
+#define CONFIG_BOARD_RESET 1 /* call board_reset() */
+
+/*-----------------------------------------------------------------------
+ * Base addresses -- Note these are effective addresses where the
+ * actual resources get mapped (not physical addresses)
+ *----------------------------------------------------------------------*/
+#define CONFIG_SYS_FLASH_BASE 0xfc000000 /* start of FLASH */
+#define CONFIG_SYS_PCI_MEMBASE 0xa0000000 /* mapped pci memory*/
+#define CONFIG_SYS_PCI_MEMBASE1 CONFIG_SYS_PCI_MEMBASE + 0x10000000
+#define CONFIG_SYS_PCI_MEMBASE2 CONFIG_SYS_PCI_MEMBASE1 + 0x10000000
+#define CONFIG_SYS_PCI_MEMBASE3 CONFIG_SYS_PCI_MEMBASE2 + 0x10000000
+
+/*Don't change either of these*/
+#define CONFIG_SYS_PCI_BASE 0xe0000000 /* internal PCI regs*/
+/*Don't change either of these*/
+
+#define CONFIG_SYS_USB_DEVICE 0x50000000
+#define CONFIG_SYS_NVRAM_BASE_ADDR 0x80000000
+#define CONFIG_SYS_BCSR_BASE (CONFIG_SYS_NVRAM_BASE_ADDR | 0x2000)
+#define CONFIG_SYS_BOOT_BASE_ADDR 0xf0000000
+
+/*-----------------------------------------------------------------------
+ * Initial RAM & stack pointer (placed in SDRAM)
+ *----------------------------------------------------------------------*/
+#define CONFIG_SYS_INIT_RAM_DCACHE 1 /* d-cache as init ram */
+#define CONFIG_SYS_INIT_RAM_ADDR 0x70000000 /* DCache */
+#define CONFIG_SYS_INIT_RAM_SIZE (4 << 10)
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
+
+/*-----------------------------------------------------------------------
+ * Serial Port
+ *----------------------------------------------------------------------*/
+#define CONFIG_CONS_INDEX 1 /* Use UART0 */
+#define CONFIG_SYS_EXT_SERIAL_CLOCK 11059200 /* use external 11.059MHz clk */
+
+/*-----------------------------------------------------------------------
+ * Environment
+ *----------------------------------------------------------------------*/
+/*
+ * Define here the location of the environment variables (FLASH or EEPROM).
+ * Note: DENX encourages to use redundant environment in FLASH.
+ */
+#if 1
+#define CONFIG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */
+#else
+#define CONFIG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */
+#endif
+
+/*-----------------------------------------------------------------------
+ * FLASH related
+ *----------------------------------------------------------------------*/
+#define CONFIG_SYS_FLASH_CFI /* The flash is CFI compatible */
+#define CONFIG_FLASH_CFI_DRIVER /* Use common CFI driver */
+#define CONFIG_SYS_FLASH_CFI_AMD_RESET 1 /* AMD RESET for STM 29W320DB! */
+
+#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
+#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max number of sectors on one chip */
+
+#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
+
+#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */
+
+#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
+
+#ifdef CONFIG_ENV_IS_IN_FLASH
+#define CONFIG_ENV_SECT_SIZE 0x20000 /* size of one complete sector */
+#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE-CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */
+
+/* Address and size of Redundant Environment Sector */
+#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR-CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
+#endif /* CONFIG_ENV_IS_IN_FLASH */
+
+/*-----------------------------------------------------------------------
+ * DDR SDRAM
+ *----------------------------------------------------------------------*/
+#undef CONFIG_SPD_EEPROM /* Don't use SPD EEPROM for setup */
+#define CONFIG_SYS_KBYTES_SDRAM (128 * 1024) /* 128MB */
+#define CONFIG_SYS_SDRAM_BANKS (2)
+
+/*-----------------------------------------------------------------------
+ * I2C
+ *----------------------------------------------------------------------*/
+#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000
+
+#define CONFIG_SYS_I2C_MULTI_EEPROMS
+#define CONFIG_SYS_I2C_EEPROM_ADDR (0xa8>>1)
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10
+
+#ifdef CONFIG_ENV_IS_IN_EEPROM
+#define CONFIG_ENV_SIZE 0x200 /* Size of Environment vars */
+#define CONFIG_ENV_OFFSET 0x0
+#endif /* CONFIG_ENV_IS_IN_EEPROM */
+
+/* I2C SYSMON (LM75, AD7414 is almost compatible) */
+#define CONFIG_DTT_LM75 1 /* ON Semi's LM75 */
+#define CONFIG_DTT_AD7414 1 /* use AD7414 */
+#define CONFIG_DTT_SENSORS {0} /* Sensor addresses */
+#define CONFIG_SYS_DTT_MAX_TEMP 70
+#define CONFIG_SYS_DTT_LOW_TEMP -30
+#define CONFIG_SYS_DTT_HYSTERESIS 3
+
+/*
+ * Default environment variables
+ */
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ CONFIG_AMCC_DEF_ENV \
+ CONFIG_AMCC_DEF_ENV_POWERPC \
+ CONFIG_AMCC_DEF_ENV_PPC_OLD \
+ CONFIG_AMCC_DEF_ENV_NOR_UPD \
+ "kernel_addr=fc000000\0" \
+ "ramdisk_addr=fc180000\0" \
+ ""
+
+#define CONFIG_HAS_ETH0 1 /* add support for "ethaddr" */
+#define CONFIG_HAS_ETH1 1 /* add support for "eth1addr" */
+#define CONFIG_PHY_ADDR 1 /* PHY address, See schematics */
+#define CONFIG_PHY1_ADDR 3
+
+/* Partitions */
+#define CONFIG_MAC_PARTITION
+#define CONFIG_DOS_PARTITION
+#define CONFIG_ISO_PARTITION
+
+#ifdef CONFIG_440EP
+/* USB */
+#define CONFIG_USB_OHCI_NEW
+#define CONFIG_USB_STORAGE
+#define CONFIG_SYS_OHCI_BE_CONTROLLER
+
+#undef CONFIG_SYS_USB_OHCI_BOARD_INIT
+#define CONFIG_SYS_USB_OHCI_CPU_INIT 1
+#define CONFIG_SYS_USB_OHCI_REGS_BASE (CONFIG_SYS_PERIPHERAL_BASE | 0x1000)
+#define CONFIG_SYS_USB_OHCI_SLOT_NAME "ppc440"
+#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 15
+
+/* Comment this out to enable USB 1.1 device */
+#define USB_2_0_DEVICE
+
+#define CONFIG_SUPPORT_VFAT
+#endif /* CONFIG_440EP */
+
+#ifdef DEBUG
+#define CONFIG_PANIC_HANG
+#else
+#define CONFIG_HW_WATCHDOG /* watchdog */
+#endif
+
+/*
+ * Commands additional to the ones defined in amcc-common.h
+ */
+#define CONFIG_CMD_DTT
+#define CONFIG_CMD_PCI
+
+#ifdef CONFIG_440EP
+ #define CONFIG_CMD_USB
+ #define CONFIG_CMD_FAT
+ #define CONFIG_CMD_EXT2
+#endif
+
+/*-----------------------------------------------------------------------
+ * PCI stuff
+ *-----------------------------------------------------------------------
+ */
+/* General PCI */
+#define CONFIG_PCI /* include pci support */
+#define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */
+#undef CONFIG_PCI_PNP /* do (not) pci plug-and-play */
+#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
+#define CONFIG_SYS_PCI_TARGBASE 0x80000000 /* PCIaddr mapped to CONFIG_SYS_PCI_MEMBASE*/
+
+/* Board-specific PCI */
+#define CONFIG_SYS_PCI_TARGET_INIT
+#define CONFIG_SYS_PCI_MASTER_INIT
+
+#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x10e8 /* AMCC */
+#define CONFIG_SYS_PCI_SUBSYS_ID 0xcafe /* Whatever */
+
+/*-----------------------------------------------------------------------
+ * External Bus Controller (EBC) Setup
+ *----------------------------------------------------------------------*/
+#define CONFIG_SYS_FLASH CONFIG_SYS_FLASH_BASE
+#define CONFIG_SYS_CPLD 0x80000000
+
+/* Memory Bank 0 (NOR-FLASH) initialization */
+#define CONFIG_SYS_EBC_PB0AP 0x03017300
+#define CONFIG_SYS_EBC_PB0CR (CONFIG_SYS_FLASH | 0xda000)
+
+/* Memory Bank 2 (CPLD) initialization */
+#define CONFIG_SYS_EBC_PB2AP 0x04814500
+#define CONFIG_SYS_EBC_PB2CR (CONFIG_SYS_CPLD | 0x18000)
+
+#define CONFIG_SYS_BCSR5_PCI66EN 0x80
+
+#endif /* __CONFIG_H */
Code Review / kvmfornfv.git / blobdiff