--- /dev/null
+/*
+ * Copyright 2010 Extreme Engineering Solutions, Inc.
+ * Copyright 2007-2008 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+/*
+ * xpedite550x board configuration file
+ */
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ */
+#define CONFIG_BOOKE 1 /* BOOKE */
+#define CONFIG_E500 1 /* BOOKE e500 family */
+#define CONFIG_P2020 1
+#define CONFIG_XPEDITE550X 1
+#define CONFIG_SYS_BOARD_NAME "XPedite5500"
+#define CONFIG_SYS_FORM_PMC_XMC 1
+#define CONFIG_PRPMC_PCI_ALIAS "pci0" /* Processor PMC interface on pci0 */
+#define CONFIG_BOARD_EARLY_INIT_R /* Call board_pre_init */
+
+#ifndef CONFIG_SYS_TEXT_BASE
+#define CONFIG_SYS_TEXT_BASE 0xfff80000
+#endif
+
+#define CONFIG_PCI 1 /* Enable PCI/PCIE */
+#define CONFIG_PCI_PNP 1 /* do pci plug-and-play */
+#define CONFIG_PCI_SCAN_SHOW 1 /* show pci devices on startup */
+#define CONFIG_PCIE1 1 /* PCIE controler 1 (PEX8112 or XMC) */
+#define CONFIG_FSL_PCI_INIT 1 /* Use common FSL init code */
+#define CONFIG_PCI_INDIRECT_BRIDGE 1 /* indirect PCI bridge support */
+#define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */
+#define CONFIG_FSL_PCIE_RESET 1 /* need PCIe reset errata */
+#define CONFIG_FSL_LAW 1 /* Use common FSL init code */
+#define CONFIG_FSL_ELBC 1
+
+/*
+ * Multicore config
+ */
+#define CONFIG_MP
+#define CONFIG_BPTR_VIRT_ADDR 0xee000000 /* virt boot page address */
+#define CONFIG_MPC8xxx_DISABLE_BPTR /* Don't leave BPTR enabled */
+
+/*
+ * DDR config
+ */
+#define CONFIG_SYS_FSL_DDR3
+#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */
+#define CONFIG_DDR_SPD
+#define CONFIG_MEM_INIT_VALUE 0xdeadbeef
+#define SPD_EEPROM_ADDRESS 0x54
+#define SPD_EEPROM_OFFSET 0x200 /* OFFSET of SPD in EEPROM */
+#define CONFIG_NUM_DDR_CONTROLLERS 1
+#define CONFIG_DIMM_SLOTS_PER_CTLR 1
+#define CONFIG_CHIP_SELECTS_PER_CTRL 2
+#define CONFIG_DDR_ECC
+#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
+#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/
+#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
+#define CONFIG_VERY_BIG_RAM
+
+#ifndef __ASSEMBLY__
+extern unsigned long get_board_sys_clk(unsigned long dummy);
+extern unsigned long get_board_ddr_clk(unsigned long dummy);
+#endif
+
+#define CONFIG_SYS_CLK_FREQ get_board_sys_clk(0) /* sysclk for MPC85xx */
+#define CONFIG_DDR_CLK_FREQ get_board_ddr_clk(0) /* ddrclk for MPC85xx */
+
+/*
+ * These can be toggled for performance analysis, otherwise use default.
+ */
+#define CONFIG_L2_CACHE /* toggle L2 cache */
+#define CONFIG_BTB /* toggle branch predition */
+#define CONFIG_ENABLE_36BIT_PHYS 1
+
+#define CONFIG_SYS_CCSRBAR 0xef000000
+#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR
+
+/*
+ * Diagnostics
+ */
+#define CONFIG_SYS_ALT_MEMTEST
+#define CONFIG_SYS_MEMTEST_START 0x10000000
+#define CONFIG_SYS_MEMTEST_END 0x20000000
+#define CONFIG_POST (CONFIG_SYS_POST_MEMORY | \
+ CONFIG_SYS_POST_I2C)
+#define I2C_ADDR_LIST {CONFIG_SYS_I2C_EEPROM_ADDR, \
+ CONFIG_SYS_I2C_LM75_ADDR, \
+ CONFIG_SYS_I2C_LM90_ADDR, \
+ CONFIG_SYS_I2C_PCA953X_ADDR0, \
+ CONFIG_SYS_I2C_PCA953X_ADDR2, \
+ CONFIG_SYS_I2C_PCA953X_ADDR3, \
+ CONFIG_SYS_I2C_RTC_ADDR}
+
+/*
+ * Memory map
+ * 0x0000_0000 0x7fff_ffff DDR 2G Cacheable
+ * 0x8000_0000 0xbfff_ffff PCIe1 Mem 1G non-cacheable
+ * 0xe000_0000 0xe7ff_ffff SRAM/SSRAM/L1 Cache 128M non-cacheable
+ * 0xe800_0000 0xe87f_ffff PCIe1 IO 8M non-cacheable
+ * 0xee00_0000 0xee00_ffff Boot page translation 4K non-cacheable
+ * 0xef00_0000 0xef0f_ffff CCSR/IMMR 1M non-cacheable
+ * 0xef80_0000 0xef8f_ffff NAND Flash 1M non-cacheable
+ * 0xf000_0000 0xf7ff_ffff NOR Flash 2 128M non-cacheable
+ * 0xf800_0000 0xffff_ffff NOR Flash 1 128M non-cacheable
+ */
+
+#define CONFIG_SYS_LBC_LCRR (LCRR_CLKDIV_8 | LCRR_EADC_3)
+
+/*
+ * NAND flash configuration
+ */
+#define CONFIG_SYS_NAND_BASE 0xef800000
+#define CONFIG_SYS_NAND_BASE2 0xef840000 /* Unused at this time */
+#define CONFIG_SYS_NAND_BASE_LIST {CONFIG_SYS_NAND_BASE, \
+ CONFIG_SYS_NAND_BASE2}
+#define CONFIG_SYS_MAX_NAND_DEVICE 2
+#define CONFIG_MTD_NAND_VERIFY_WRITE
+#define CONFIG_SYS_NAND_QUIET_TEST /* 2nd NAND flash not always populated */
+#define CONFIG_NAND_FSL_ELBC
+
+/*
+ * NOR flash configuration
+ */
+#define CONFIG_SYS_FLASH_BASE 0xf8000000
+#define CONFIG_SYS_FLASH_BASE2 0xf0000000
+#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE2}
+#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */
+#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */
+#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
+#define CONFIG_FLASH_CFI_DRIVER
+#define CONFIG_SYS_FLASH_CFI
+#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
+#define CONFIG_SYS_FLASH_AUTOPROTECT_LIST { {0xfff40000, 0xc0000}, \
+ {0xf7f40000, 0xc0000} }
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
+
+/*
+ * Chip select configuration
+ */
+/* NOR Flash 0 on CS0 */
+#define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE | \
+ BR_PS_16 | \
+ BR_V)
+#define CONFIG_SYS_OR0_PRELIM (OR_AM_128MB | \
+ OR_GPCM_CSNT | \
+ OR_GPCM_XACS | \
+ OR_GPCM_ACS_DIV2 | \
+ OR_GPCM_SCY_8 | \
+ OR_GPCM_TRLX | \
+ OR_GPCM_EHTR | \
+ OR_GPCM_EAD)
+
+/* NOR Flash 1 on CS1 */
+#define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_FLASH_BASE2 | \
+ BR_PS_16 | \
+ BR_V)
+#define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_OR0_PRELIM
+
+/* NAND flash on CS2 */
+#define CONFIG_SYS_BR2_PRELIM (CONFIG_SYS_NAND_BASE | \
+ (2<<BR_DECC_SHIFT) | \
+ BR_PS_8 | \
+ BR_MS_FCM | \
+ BR_V)
+
+/* NAND flash on CS2 */
+#define CONFIG_SYS_OR2_PRELIM (OR_AM_256KB | \
+ OR_FCM_PGS | \
+ OR_FCM_CSCT | \
+ OR_FCM_CST | \
+ OR_FCM_CHT | \
+ OR_FCM_SCY_1 | \
+ OR_FCM_TRLX | \
+ OR_FCM_EHTR)
+
+/* NAND flash on CS3 */
+#define CONFIG_SYS_BR3_PRELIM (CONFIG_SYS_NAND_BASE2 | \
+ (2<<BR_DECC_SHIFT) | \
+ BR_PS_8 | \
+ BR_MS_FCM | \
+ BR_V)
+#define CONFIG_SYS_OR3_PRELIM CONFIG_SYS_OR2_PRELIM
+
+/*
+ * Use L1 as initial stack
+ */
+#define CONFIG_SYS_INIT_RAM_LOCK 1
+#define CONFIG_SYS_INIT_RAM_ADDR 0xe0000000
+#define CONFIG_SYS_INIT_RAM_SIZE 0x00004000
+
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
+
+#define CONFIG_SYS_MONITOR_LEN (512 * 1024) /* Reserve 512 KB for Mon */
+#define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserved for malloc */
+
+/*
+ * Serial Port
+ */
+#define CONFIG_CONS_INDEX 1
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE 1
+#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
+#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500)
+#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600)
+#define CONFIG_SYS_BAUDRATE_TABLE \
+ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
+#define CONFIG_BAUDRATE 115200
+#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
+#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
+
+/*
+ * Use the HUSH parser
+ */
+#define CONFIG_SYS_HUSH_PARSER
+
+/*
+ * Pass open firmware flat tree
+ */
+#define CONFIG_OF_LIBFDT 1
+#define CONFIG_OF_BOARD_SETUP 1
+#define CONFIG_OF_STDOUT_VIA_ALIAS 1
+#define CONFIG_FDT_FIXUP_PCI_IRQ 1
+
+/*
+ * I2C
+ */
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_FSL
+#define CONFIG_SYS_FSL_I2C_SPEED 400000
+#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
+#define CONFIG_SYS_FSL_I2C2_SPEED 400000
+#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100
+
+/* I2C DS7505 temperature sensor */
+#define CONFIG_DTT_LM75
+#define CONFIG_DTT_SENSORS { 0 }
+#define CONFIG_SYS_I2C_LM75_ADDR 0x48
+
+/* I2C ADT7461 temperature sensor */
+#define CONFIG_SYS_I2C_LM90_ADDR 0x4C
+
+/* I2C EEPROM - AT24C128B */
+#define CONFIG_SYS_I2C_EEPROM_ADDR 0x54
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6 /* 64 byte pages */
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* take up to 10 msec */
+
+/* I2C RTC */
+#define CONFIG_RTC_M41T11 1
+#define CONFIG_SYS_I2C_RTC_ADDR 0x68
+#define CONFIG_SYS_M41T11_BASE_YEAR 2000
+
+/* GPIO */
+#define CONFIG_PCA953X
+#define CONFIG_SYS_I2C_PCA953X_ADDR0 0x18
+#define CONFIG_SYS_I2C_PCA953X_ADDR1 0x1c
+#define CONFIG_SYS_I2C_PCA953X_ADDR2 0x1e
+#define CONFIG_SYS_I2C_PCA953X_ADDR3 0x1f
+#define CONFIG_SYS_I2C_PCA953X_ADDR CONFIG_SYS_I2C_PCA953X_ADDR0
+
+/*
+ * GPIO pin definitions, PU = pulled high, PD = pulled low
+ */
+/* PCA9557 @ 0x18*/
+#define CONFIG_SYS_PCA953X_C0_SER0_EN 0x01 /* PU; UART0 enable (1: enabled) */
+#define CONFIG_SYS_PCA953X_C0_SER0_MODE 0x02 /* PU; UART0 serial mode select (1: RS-485, 0: RS-232) */
+#define CONFIG_SYS_PCA953X_C0_SER1_EN 0x04 /* PU; UART1 enable (1: enabled) */
+#define CONFIG_SYS_PCA953X_C0_SER1_MODE 0x08 /* PU; UART1 serial mode select (1: RS-485, 0: RS-232) */
+#define CONFIG_SYS_PCA953X_C0_FLASH_PASS_CS 0x10 /* PU; Boot flash CS select */
+#define CONFIG_SYS_PCA953X_NVM_WP 0x20 /* PU; Write protection (0: disabled, 1: enabled) */
+
+/* PCA9557 @ 0x1e*/
+#define CONFIG_SYS_PCA953X_XMC_GA0 0x01 /* PU; */
+#define CONFIG_SYS_PCA953X_XMC_GA1 0x02 /* PU; */
+#define CONFIG_SYS_PCA953X_XMC_GA2 0x04 /* PU; */
+#define CONFIG_SYS_PCA953X_XMC_WAKE 0x10 /* PU; */
+#define CONFIG_SYS_PCA953X_XMC_BIST 0x20 /* Enable XMC BIST */
+#define CONFIG_SYS_PCA953X_PMC_EREADY 0x40 /* PU; PMC PCI eready */
+#define CONFIG_SYS_PCA953X_PMC_MONARCH 0x80 /* PMC monarch mode enable */
+
+/* PCA9557 @ 0x1f */
+#define CONFIG_SYS_PCA953X_MC_GPIO0 0x01 /* PU; */
+#define CONFIG_SYS_PCA953X_MC_GPIO1 0x02 /* PU; */
+#define CONFIG_SYS_PCA953X_MC_GPIO2 0x04 /* PU; */
+#define CONFIG_SYS_PCA953X_MC_GPIO3 0x08 /* PU; */
+#define CONFIG_SYS_PCA953X_MC_GPIO4 0x10 /* PU; */
+#define CONFIG_SYS_PCA953X_MC_GPIO5 0x20 /* PU; */
+#define CONFIG_SYS_PCA953X_MC_GPIO6 0x40 /* PU; */
+#define CONFIG_SYS_PCA953X_MC_GPIO7 0x80 /* PU; */
+
+/*
+ * General PCI
+ * Memory space is mapped 1-1, but I/O space must start from 0.
+ */
+
+/* controller 1 - PEX8112 or XMC, depending on build option */
+#define CONFIG_SYS_PCIE1_MEM_BUS 0x80000000
+#define CONFIG_SYS_PCIE1_MEM_PHYS CONFIG_SYS_PCIE1_MEM_BUS
+#define CONFIG_SYS_PCIE1_MEM_SIZE 0x40000000 /* 1G */
+#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000
+#define CONFIG_SYS_PCIE1_IO_PHYS 0xe8000000
+#define CONFIG_SYS_PCIE1_IO_SIZE 0x00800000 /* 8M */
+
+
+/*
+ * Networking options
+ */
+#define CONFIG_TSEC_ENET /* tsec ethernet support */
+#define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */
+#define CONFIG_TSEC_TBI
+#define CONFIG_MII 1 /* MII PHY management */
+#define CONFIG_MII_DEFAULT_TSEC 1 /* Allow unregistered phys */
+#define CONFIG_ETHPRIME "eTSEC2"
+
+/*
+ * In-band SGMII auto-negotiation between TBI and BCM5482S PHY fails, force
+ * 1000mbps SGMII link
+ */
+#define CONFIG_TSEC_TBICR_SETTINGS ( \
+ TBICR_PHY_RESET \
+ | TBICR_FULL_DUPLEX \
+ | TBICR_SPEED1_SET \
+ )
+
+#define CONFIG_TSEC1 1
+#define CONFIG_TSEC1_NAME "eTSEC1"
+#define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
+#define TSEC1_PHY_ADDR 1
+#define TSEC1_PHYIDX 0
+#define CONFIG_HAS_ETH0
+
+#define CONFIG_TSEC2 1
+#define CONFIG_TSEC2_NAME "eTSEC2"
+#define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
+#define TSEC2_PHY_ADDR 2
+#define TSEC2_PHYIDX 0
+#define CONFIG_HAS_ETH1
+
+#define CONFIG_TSEC3 1
+#define CONFIG_TSEC3_NAME "eTSEC3"
+#define TSEC3_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
+#define TSEC3_PHY_ADDR 3
+#define TSEC3_PHYIDX 0
+#define CONFIG_HAS_ETH2
+
+/*
+ * USB
+ */
+#define CONFIG_USB_STORAGE
+#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_FSL
+#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
+#define CONFIG_DOS_PARTITION
+
+/*
+ * Command configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_ASKENV
+#define CONFIG_CMD_DATE
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_DTT
+#define CONFIG_CMD_EEPROM
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_FLASH
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_JFFS2
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_NAND
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_PCA953X
+#define CONFIG_CMD_PCA953X_INFO
+#define CONFIG_CMD_PCI
+#define CONFIG_CMD_PCI_ENUM
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_REGINFO
+#define CONFIG_CMD_SAVEENV
+#define CONFIG_CMD_SNTP
+#define CONFIG_CMD_USB
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
+#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
+#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
+#define CONFIG_AUTO_COMPLETE 1 /* add autocompletion support */
+#define CONFIG_LOADADDR 0x1000000 /* default location for tftp and bootm */
+#define CONFIG_BOOTDELAY 3 /* -1 disables auto-boot */
+#define CONFIG_PANIC_HANG /* do not reset board on panic */
+#define CONFIG_PREBOOT /* enable preboot variable */
+#define CONFIG_FIT 1
+#define CONFIG_FIT_VERBOSE 1
+#define CONFIG_INTEGRITY /* support booting INTEGRITY OS */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 16 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_SYS_BOOTMAPSZ (16 << 20) /* Initial Memory map for Linux*/
+#define CONFIG_SYS_BOOTM_LEN (16 << 20) /* Increase max gunzip size */
+
+/*
+ * Environment Configuration
+ */
+#define CONFIG_ENV_IS_IN_FLASH 1
+#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128k (one sector) for env */
+#define CONFIG_ENV_SIZE 0x8000
+#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - (256 * 1024))
+
+/*
+ * Flash memory map:
+ * fff80000 - ffffffff Pri U-Boot (512 KB)
+ * fff40000 - fff7ffff Pri U-Boot Environment (256 KB)
+ * fff00000 - fff3ffff Pri FDT (256KB)
+ * fef00000 - ffefffff Pri OS image (16MB)
+ * f8000000 - feefffff Pri OS Use/Filesystem (111MB)
+ *
+ * f7f80000 - f7ffffff Sec U-Boot (512 KB)
+ * f7f40000 - f7f7ffff Sec U-Boot Environment (256 KB)
+ * f7f00000 - f7f3ffff Sec FDT (256KB)
+ * f6f00000 - f7efffff Sec OS image (16MB)
+ * f0000000 - f6efffff Sec OS Use/Filesystem (111MB)
+ */
+#define CONFIG_UBOOT1_ENV_ADDR __stringify(0xfff80000)
+#define CONFIG_UBOOT2_ENV_ADDR __stringify(0xf7f80000)
+#define CONFIG_FDT1_ENV_ADDR __stringify(0xfff00000)
+#define CONFIG_FDT2_ENV_ADDR __stringify(0xf7f00000)
+#define CONFIG_OS1_ENV_ADDR __stringify(0xfef00000)
+#define CONFIG_OS2_ENV_ADDR __stringify(0xf6f00000)
+
+#define CONFIG_PROG_UBOOT1 \
+ "$download_cmd $loadaddr $ubootfile; " \
+ "if test $? -eq 0; then " \
+ "protect off "CONFIG_UBOOT1_ENV_ADDR" +80000; " \
+ "erase "CONFIG_UBOOT1_ENV_ADDR" +80000; " \
+ "cp.w $loadaddr "CONFIG_UBOOT1_ENV_ADDR" 40000; " \
+ "protect on "CONFIG_UBOOT1_ENV_ADDR" +80000; " \
+ "cmp.b $loadaddr "CONFIG_UBOOT1_ENV_ADDR" 80000; " \
+ "if test $? -ne 0; then " \
+ "echo PROGRAM FAILED; " \
+ "else; " \
+ "echo PROGRAM SUCCEEDED; " \
+ "fi; " \
+ "else; " \
+ "echo DOWNLOAD FAILED; " \
+ "fi;"
+
+#define CONFIG_PROG_UBOOT2 \
+ "$download_cmd $loadaddr $ubootfile; " \
+ "if test $? -eq 0; then " \
+ "protect off "CONFIG_UBOOT2_ENV_ADDR" +80000; " \
+ "erase "CONFIG_UBOOT2_ENV_ADDR" +80000; " \
+ "cp.w $loadaddr "CONFIG_UBOOT2_ENV_ADDR" 40000; " \
+ "protect on "CONFIG_UBOOT2_ENV_ADDR" +80000; " \
+ "cmp.b $loadaddr "CONFIG_UBOOT2_ENV_ADDR" 80000; " \
+ "if test $? -ne 0; then " \
+ "echo PROGRAM FAILED; " \
+ "else; " \
+ "echo PROGRAM SUCCEEDED; " \
+ "fi; " \
+ "else; " \
+ "echo DOWNLOAD FAILED; " \
+ "fi;"
+
+#define CONFIG_BOOT_OS_NET \
+ "$download_cmd $osaddr $osfile; " \
+ "if test $? -eq 0; then " \
+ "if test -n $fdtaddr; then " \
+ "$download_cmd $fdtaddr $fdtfile; " \
+ "if test $? -eq 0; then " \
+ "bootm $osaddr - $fdtaddr; " \
+ "else; " \
+ "echo FDT DOWNLOAD FAILED; " \
+ "fi; " \
+ "else; " \
+ "bootm $osaddr; " \
+ "fi; " \
+ "else; " \
+ "echo OS DOWNLOAD FAILED; " \
+ "fi;"
+
+#define CONFIG_PROG_OS1 \
+ "$download_cmd $osaddr $osfile; " \
+ "if test $? -eq 0; then " \
+ "erase "CONFIG_OS1_ENV_ADDR" +$filesize; " \
+ "cp.b $osaddr "CONFIG_OS1_ENV_ADDR" $filesize; " \
+ "cmp.b $osaddr "CONFIG_OS1_ENV_ADDR" $filesize; " \
+ "if test $? -ne 0; then " \
+ "echo OS PROGRAM FAILED; " \
+ "else; " \
+ "echo OS PROGRAM SUCCEEDED; " \
+ "fi; " \
+ "else; " \
+ "echo OS DOWNLOAD FAILED; " \
+ "fi;"
+
+#define CONFIG_PROG_OS2 \
+ "$download_cmd $osaddr $osfile; " \
+ "if test $? -eq 0; then " \
+ "erase "CONFIG_OS2_ENV_ADDR" +$filesize; " \
+ "cp.b $osaddr "CONFIG_OS2_ENV_ADDR" $filesize; " \
+ "cmp.b $osaddr "CONFIG_OS2_ENV_ADDR" $filesize; " \
+ "if test $? -ne 0; then " \
+ "echo OS PROGRAM FAILED; " \
+ "else; " \
+ "echo OS PROGRAM SUCCEEDED; " \
+ "fi; " \
+ "else; " \
+ "echo OS DOWNLOAD FAILED; " \
+ "fi;"
+
+#define CONFIG_PROG_FDT1 \
+ "$download_cmd $fdtaddr $fdtfile; " \
+ "if test $? -eq 0; then " \
+ "erase "CONFIG_FDT1_ENV_ADDR" +$filesize;" \
+ "cp.b $fdtaddr "CONFIG_FDT1_ENV_ADDR" $filesize; " \
+ "cmp.b $fdtaddr "CONFIG_FDT1_ENV_ADDR" $filesize; " \
+ "if test $? -ne 0; then " \
+ "echo FDT PROGRAM FAILED; " \
+ "else; " \
+ "echo FDT PROGRAM SUCCEEDED; " \
+ "fi; " \
+ "else; " \
+ "echo FDT DOWNLOAD FAILED; " \
+ "fi;"
+
+#define CONFIG_PROG_FDT2 \
+ "$download_cmd $fdtaddr $fdtfile; " \
+ "if test $? -eq 0; then " \
+ "erase "CONFIG_FDT2_ENV_ADDR" +$filesize;" \
+ "cp.b $fdtaddr "CONFIG_FDT2_ENV_ADDR" $filesize; " \
+ "cmp.b $fdtaddr "CONFIG_FDT2_ENV_ADDR" $filesize; " \
+ "if test $? -ne 0; then " \
+ "echo FDT PROGRAM FAILED; " \
+ "else; " \
+ "echo FDT PROGRAM SUCCEEDED; " \
+ "fi; " \
+ "else; " \
+ "echo FDT DOWNLOAD FAILED; " \
+ "fi;"
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "autoload=yes\0" \
+ "download_cmd=tftp\0" \
+ "console_args=console=ttyS0,115200\0" \
+ "root_args=root=/dev/nfs rw\0" \
+ "misc_args=ip=on\0" \
+ "set_bootargs=setenv bootargs ${console_args} ${root_args} ${misc_args}\0" \
+ "bootfile=/home/user/file\0" \
+ "osfile=/home/user/board.uImage\0" \
+ "fdtfile=/home/user/board.dtb\0" \
+ "ubootfile=/home/user/u-boot.bin\0" \
+ "fdtaddr=c00000\0" \
+ "osaddr=0x1000000\0" \
+ "loadaddr=0x1000000\0" \
+ "prog_uboot1="CONFIG_PROG_UBOOT1"\0" \
+ "prog_uboot2="CONFIG_PROG_UBOOT2"\0" \
+ "prog_os1="CONFIG_PROG_OS1"\0" \
+ "prog_os2="CONFIG_PROG_OS2"\0" \
+ "prog_fdt1="CONFIG_PROG_FDT1"\0" \
+ "prog_fdt2="CONFIG_PROG_FDT2"\0" \
+ "bootcmd_net=run set_bootargs; "CONFIG_BOOT_OS_NET"\0" \
+ "bootcmd_flash1=run set_bootargs; " \
+ "bootm "CONFIG_OS1_ENV_ADDR" - "CONFIG_FDT1_ENV_ADDR"\0"\
+ "bootcmd_flash2=run set_bootargs; " \
+ "bootm "CONFIG_OS2_ENV_ADDR" - "CONFIG_FDT2_ENV_ADDR"\0"\
+ "bootcmd=run bootcmd_flash1\0"
+#endif /* __CONFIG_H */
Code Review / kvmfornfv.git / blobdiff