--- /dev/null
+/*
+ * (C) Copyright 2002 Scott McNutt <smcnutt@artesyncp.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+/*
+ * config for XPedite1000 from XES Inc.
+ * Ported from EBONY config by Travis B. Sawyer <tsawyer@sandburst.com>
+ * (C) Copyright 2003 Sandburst Corporation
+ * board/config_EBONY.h - configuration for AMCC 440GP Ref (Ebony)
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/* High Level Configuration Options */
+#define CONFIG_XPEDITE1000 1
+#define CONFIG_SYS_BOARD_NAME "XPedite1000"
+#define CONFIG_SYS_FORM_PMC 1
+#define CONFIG_440 1
+#define CONFIG_440GX 1 /* 440 GX */
+#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */
+#define CONFIG_SYS_CLK_FREQ 33333333 /* external freq to pll */
+
+#define CONFIG_SYS_TEXT_BASE 0xFFF80000
+
+/*
+ * DDR config
+ */
+#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for setup */
+#define SPD_EEPROM_ADDRESS {0x54} /* SPD i2c spd addresses */
+#define CONFIG_VERY_BIG_RAM 1
+
+/*
+ * Base addresses -- Note these are effective addresses where the
+ * actual resources get mapped (not physical addresses)
+ */
+#define CONFIG_SYS_SDRAM_BASE 0x00000000
+#define CONFIG_SYS_FLASH_BASE 0xff000000 /* start of FLASH */
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
+#define CONFIG_SYS_PCI_MEMBASE 0x80000000 /* mapped pci memory */
+#define CONFIG_SYS_ISRAM_BASE 0xc0000000 /* internal SRAM */
+#define CONFIG_SYS_PCI_BASE 0xd0000000 /* internal PCI regs */
+#define CONFIG_SYS_NVRAM_BASE_ADDR (CONFIG_SYS_PERIPHERAL_BASE + 0x08000000)
+#define CONFIG_SYS_GPIO_BASE (CONFIG_SYS_PERIPHERAL_BASE + 0x00000700)
+
+/*
+ * Diagnostics
+ */
+#define CONFIG_SYS_ALT_MEMTEST
+#define CONFIG_SYS_MEMTEST_START 0x0400000
+#define CONFIG_SYS_MEMTEST_END 0x0C00000
+
+/* POST support */
+#define CONFIG_POST (CONFIG_SYS_POST_RTC | \
+ CONFIG_SYS_POST_I2C)
+
+/*
+ * LED support
+ */
+#define USR_LED0 0x00000080
+#define USR_LED1 0x00000100
+#define USR_LED2 0x00000200
+#define USR_LED3 0x00000400
+
+#ifndef __ASSEMBLY__
+extern unsigned long in32(unsigned int);
+extern void out32(unsigned int, unsigned long);
+
+#define LED0_ON() out32(CONFIG_SYS_GPIO_BASE, (in32(CONFIG_SYS_GPIO_BASE) & ~USR_LED0))
+#define LED1_ON() out32(CONFIG_SYS_GPIO_BASE, (in32(CONFIG_SYS_GPIO_BASE) & ~USR_LED1))
+#define LED2_ON() out32(CONFIG_SYS_GPIO_BASE, (in32(CONFIG_SYS_GPIO_BASE) & ~USR_LED2))
+#define LED3_ON() out32(CONFIG_SYS_GPIO_BASE, (in32(CONFIG_SYS_GPIO_BASE) & ~USR_LED3))
+
+#define LED0_OFF() out32(CONFIG_SYS_GPIO_BASE, (in32(CONFIG_SYS_GPIO_BASE) | USR_LED0))
+#define LED1_OFF() out32(CONFIG_SYS_GPIO_BASE, (in32(CONFIG_SYS_GPIO_BASE) | USR_LED1))
+#define LED2_OFF() out32(CONFIG_SYS_GPIO_BASE, (in32(CONFIG_SYS_GPIO_BASE) | USR_LED2))
+#define LED3_OFF() out32(CONFIG_SYS_GPIO_BASE, (in32(CONFIG_SYS_GPIO_BASE) | USR_LED3))
+#endif
+
+/*
+ * Use internal SRAM for initial stack
+ */
+#define CONFIG_SYS_TEMP_STACK_OCM 1
+#define CONFIG_SYS_OCM_DATA_ADDR CONFIG_SYS_ISRAM_BASE
+#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_ISRAM_BASE /* Initial RAM address */
+#define CONFIG_SYS_INIT_RAM_SIZE 0x2000 /* Size of used area in RAM */
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET (CONFIG_SYS_GBL_DATA_OFFSET - 0x4)
+
+#define CONFIG_SYS_MONITOR_LEN (512 * 1024) /* Reserve 512 KB for Mon */
+#define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserved for malloc */
+
+/*
+ * Serial Port
+ */
+#define CONFIG_CONS_INDEX 1 /* Use UART0 */
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE 1
+#define CONFIG_SYS_NS16550_CLK get_serial_clock()
+
+#define CONFIG_SYS_BAUDRATE_TABLE \
+ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400}
+#define CONFIG_BAUDRATE 115200
+#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
+#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
+
+/*
+ * Use the HUSH parser
+ */
+#define CONFIG_SYS_HUSH_PARSER
+
+/*
+ * NOR flash configuration
+ */
+#define CONFIG_SYS_MAX_FLASH_BANKS 3
+#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE, 0xf0000000, 0xf4000000 }
+#define CONFIG_SYS_MAX_FLASH_SECT 512 /* sectors per device */
+#define CONFIG_FLASH_CFI_DRIVER
+#define CONFIG_SYS_FLASH_CFI
+#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
+#define CONFIG_SYS_FLASH_QUIET_TEST /* MirrorBit flashes are optional */
+#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
+
+/*
+ * I2C
+ */
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_PPC4XX
+#define CONFIG_SYS_I2C_PPC4XX_CH0
+#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000
+#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7f
+
+/* I2C EEPROM */
+#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10
+
+/* I2C RTC: STMicro M41T00 */
+#define CONFIG_RTC_M41T11 1
+#define CONFIG_SYS_I2C_RTC_ADDR 0x68
+#define CONFIG_SYS_M41T11_BASE_YEAR 2000
+
+/*
+ * PCI
+ */
+/* General PCI */
+#define CONFIG_PCI /* include pci support */
+#define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */
+#define CONFIG_PCI_PNP /* do pci plug-and-play */
+#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
+#define CONFIG_SYS_PCI_TARGBASE 0x80000000 /* PCIaddr mapped to CONFIG_SYS_PCI_MEMBASE */
+
+/* Board-specific PCI */
+#define CONFIG_SYS_PCI_TARGET_INIT /* let board init pci target */
+#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1014 /* IBM */
+#define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0xcafe /* Whatever */
+#define CONFIG_SYS_PCI_FORCE_PCI_CONV /* Force PCI Conventional Mode */
+
+/*
+ * Networking options
+ */
+#define CONFIG_PPC4xx_EMAC
+#define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */
+#define CONFIG_MII 1 /* MII PHY management */
+#define CONFIG_PHY_RESET 1 /* reset phy upon startup */
+#define CONFIG_SYS_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */
+#define CONFIG_ETHPRIME "ppc_4xx_eth2"
+#define CONFIG_PHY_ADDR 4 /* PHY address phy0 not populated */
+#define CONFIG_PHY2_ADDR 4 /* PHY address phy2 */
+#define CONFIG_HAS_ETH2 1 /* add support for "eth2addr" */
+#define CONFIG_PHY3_ADDR 8 /* PHY address phy3 */
+#define CONFIG_HAS_ETH3 1 /* add support for "eth3addr" */
+
+/* BOOTP options */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+/*
+ * Command configuration
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_ASKENV
+#define CONFIG_CMD_DATE
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_EEPROM
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_FLASH
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_IRQ
+#define CONFIG_CMD_JFFS2
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_PCI
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_SAVEENV
+#define CONFIG_CMD_SNTP
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
+#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
+#define CONFIG_CMDLINE_EDITING 1 /* Command-line editing */
+#define CONFIG_BOOTDELAY 3 /* -1 disables auto-boot */
+#define CONFIG_PANIC_HANG /* do not reset board on panic */
+#define CONFIG_PREBOOT /* enable preboot variable */
+#define CONFIG_FIT 1
+#define CONFIG_FIT_VERBOSE 1
+#define CONFIG_INTEGRITY /* support booting INTEGRITY OS */
+#define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_into (bd_t) */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+
+/*
+ * Environment Configuration
+ */
+#define CONFIG_ENV_IS_IN_FLASH 1
+#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128k (one sector) for env */
+#define CONFIG_ENV_SIZE 0x8000
+#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - (256 * 1024))
+
+/*
+ * Flash memory map:
+ * fff80000 - ffffffff U-Boot (512 KB)
+ * fff40000 - fff7ffff U-Boot Environment (256 KB)
+ * fff00000 - fff3ffff FDT (256KB)
+ * ffc00000 - ffefffff OS image (3MB)
+ * ff000000 - ffbfffff OS Use/Filesystem (12MB)
+ */
+
+#define CONFIG_UBOOT_ENV_ADDR __stringify(CONFIG_SYS_TEXT_BASE)
+#define CONFIG_FDT_ENV_ADDR __stringify(0xfff00000)
+#define CONFIG_OS_ENV_ADDR __stringify(0xffc00000)
+
+#define CONFIG_PROG_UBOOT \
+ "$download_cmd $loadaddr $ubootfile; " \
+ "if test $? -eq 0; then " \
+ "protect off "CONFIG_UBOOT_ENV_ADDR" +80000; " \
+ "erase "CONFIG_UBOOT_ENV_ADDR" +80000; " \
+ "cp.w $loadaddr "CONFIG_UBOOT_ENV_ADDR" 40000; " \
+ "protect on "CONFIG_UBOOT_ENV_ADDR" +80000; " \
+ "cmp.b $loadaddr "CONFIG_UBOOT_ENV_ADDR" 80000; " \
+ "if test $? -ne 0; then " \
+ "echo PROGRAM FAILED; " \
+ "else; " \
+ "echo PROGRAM SUCCEEDED; " \
+ "fi; " \
+ "else; " \
+ "echo DOWNLOAD FAILED; " \
+ "fi;"
+
+#define CONFIG_BOOT_OS_NET \
+ "$download_cmd $osaddr $osfile; " \
+ "if test $? -eq 0; then " \
+ "if test -n $fdtaddr; then " \
+ "$download_cmd $fdtaddr $fdtfile; " \
+ "if test $? -eq 0; then " \
+ "bootm $osaddr - $fdtaddr; " \
+ "else; " \
+ "echo FDT DOWNLOAD FAILED; " \
+ "fi; " \
+ "else; " \
+ "bootm $osaddr; " \
+ "fi; " \
+ "else; " \
+ "echo OS DOWNLOAD FAILED; " \
+ "fi;"
+
+#define CONFIG_PROG_OS \
+ "$download_cmd $osaddr $osfile; " \
+ "if test $? -eq 0; then " \
+ "erase "CONFIG_OS_ENV_ADDR" +$filesize; " \
+ "cp.b $osaddr "CONFIG_OS_ENV_ADDR" $filesize; " \
+ "cmp.b $osaddr "CONFIG_OS_ENV_ADDR" $filesize; " \
+ "if test $? -ne 0; then " \
+ "echo OS PROGRAM FAILED; " \
+ "else; " \
+ "echo OS PROGRAM SUCCEEDED; " \
+ "fi; " \
+ "else; " \
+ "echo OS DOWNLOAD FAILED; " \
+ "fi;"
+
+#define CONFIG_PROG_FDT \
+ "$download_cmd $fdtaddr $fdtfile; " \
+ "if test $? -eq 0; then " \
+ "erase "CONFIG_FDT_ENV_ADDR" +$filesize;" \
+ "cp.b $fdtaddr "CONFIG_FDT_ENV_ADDR" $filesize; " \
+ "cmp.b $fdtaddr "CONFIG_FDT_ENV_ADDR" $filesize; " \
+ "if test $? -ne 0; then " \
+ "echo FDT PROGRAM FAILED; " \
+ "else; " \
+ "echo FDT PROGRAM SUCCEEDED; " \
+ "fi; " \
+ "else; " \
+ "echo FDT DOWNLOAD FAILED; " \
+ "fi;"
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "autoload=yes\0" \
+ "download_cmd=tftp\0" \
+ "console_args=console=ttyS0,115200\0" \
+ "root_args=root=/dev/nfs rw\0" \
+ "misc_args=ip=on\0" \
+ "set_bootargs=setenv bootargs ${console_args} ${root_args} ${misc_args}\0" \
+ "bootfile=/home/user/file\0" \
+ "osfile=/home/user/board.uImage\0" \
+ "fdtfile=/home/user/board.dtb\0" \
+ "ubootfile=/home/user/u-boot.bin\0" \
+ "fdtaddr=c00000\0" \
+ "osaddr=0x1000000\0" \
+ "loadaddr=0x1000000\0" \
+ "prog_uboot="CONFIG_PROG_UBOOT"\0" \
+ "prog_os="CONFIG_PROG_OS"\0" \
+ "prog_fdt="CONFIG_PROG_FDT"\0" \
+ "bootcmd_net=run set_bootargs; "CONFIG_BOOT_OS_NET"\0" \
+ "bootcmd_flash=run set_bootargs; " \
+ "bootm "CONFIG_OS_ENV_ADDR" - "CONFIG_FDT_ENV_ADDR"\0" \
+ "bootcmd=run bootcmd_flash\0"
+#endif /* __CONFIG_H */
Code Review / kvmfornfv.git / blobdiff