--- /dev/null
+/*
+ * esd vme8349 U-Boot configuration file
+ * Copyright (c) 2008, 2009 esd gmbh Hannover Germany
+ *
+ * (C) Copyright 2006-2010
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * reinhard.arlt@esd-electronics.de
+ * Based on the MPC8349EMDS config.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+/*
+ * vme8349 board configuration file.
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * Top level Makefile configuration choices
+ */
+#ifdef CONFIG_CADDY2
+#define VME_CADDY2
+#endif
+
+/*
+ * High Level Configuration Options
+ */
+#define CONFIG_E300 1 /* E300 Family */
+#define CONFIG_MPC834x 1 /* MPC834x family */
+#define CONFIG_MPC8349 1 /* MPC8349 specific */
+#define CONFIG_VME8349 1 /* ESD VME8349 board specific */
+
+#define CONFIG_SYS_TEXT_BASE 0xFFF00000
+
+#define CONFIG_MISC_INIT_R
+
+#define CONFIG_PCI
+/* Don't enable PCI2 on vme834x - it doesn't exist physically. */
+#undef CONFIG_MPC83XX_PCI2 /* support for 2nd PCI controller */
+
+#define CONFIG_PCI_66M
+#ifdef CONFIG_PCI_66M
+#define CONFIG_83XX_CLKIN 66000000 /* in Hz */
+#else
+#define CONFIG_83XX_CLKIN 33000000 /* in Hz */
+#endif
+
+#ifndef CONFIG_SYS_CLK_FREQ
+#ifdef CONFIG_PCI_66M
+#define CONFIG_SYS_CLK_FREQ 66000000
+#define HRCWL_CSB_TO_CLKIN HRCWL_CSB_TO_CLKIN_4X1
+#else
+#define CONFIG_SYS_CLK_FREQ 33000000
+#define HRCWL_CSB_TO_CLKIN HRCWL_CSB_TO_CLKIN_8X1
+#endif
+#endif
+
+#define CONFIG_SYS_IMMR 0xE0000000
+
+#undef CONFIG_SYS_DRAM_TEST /* memory test, takes time */
+#define CONFIG_SYS_MEMTEST_START 0x00000000 /* memtest region */
+#define CONFIG_SYS_MEMTEST_END 0x00100000
+
+/*
+ * DDR Setup
+ */
+#define CONFIG_DDR_ECC /* only for ECC DDR module */
+#define CONFIG_DDR_ECC_CMD /* use DDR ECC user commands */
+#define CONFIG_SPD_EEPROM
+#define SPD_EEPROM_ADDRESS 0x54
+#define CONFIG_SYS_READ_SPD vme8349_read_spd
+#define CONFIG_SYS_83XX_DDR_USES_CS0 /* esd; Fsl board uses CS2/CS3 */
+
+/*
+ * 32-bit data path mode.
+ *
+ * Please note that using this mode for devices with the real density of 64-bit
+ * effectively reduces the amount of available memory due to the effect of
+ * wrapping around while translating address to row/columns, for example in the
+ * 256MB module the upper 128MB get aliased with contents of the lower
+ * 128MB); normally this define should be used for devices with real 32-bit
+ * data path.
+ */
+#undef CONFIG_DDR_32BIT
+
+#define CONFIG_SYS_DDR_BASE 0x00000000 /* DDR is sys memory*/
+#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE
+#define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE
+#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL (DDR_SDRAM_CLK_CNTL_SS_EN \
+ | DDR_SDRAM_CLK_CNTL_CLK_ADJUST_075)
+#define CONFIG_DDR_2T_TIMING
+#define CONFIG_SYS_DDRCDR (DDRCDR_DHC_EN \
+ | DDRCDR_ODT \
+ | DDRCDR_Q_DRN)
+ /* 0x80080001 */
+
+/*
+ * FLASH on the Local Bus
+ */
+#define CONFIG_SYS_FLASH_CFI
+#define CONFIG_FLASH_CFI_DRIVER /* use the CFI driver */
+#ifdef VME_CADDY2
+#define CONFIG_SYS_FLASH_BASE 0xffc00000 /* start of FLASH */
+#define CONFIG_SYS_FLASH_SIZE 4 /* flash size in MB */
+#define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE | \
+ BR_PS_16 | /* 16bit */ \
+ BR_MS_GPCM | /* MSEL = GPCM */ \
+ BR_V) /* valid */
+
+#define CONFIG_SYS_OR0_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \
+ | OR_GPCM_XAM \
+ | OR_GPCM_CSNT \
+ | OR_GPCM_ACS_DIV2 \
+ | OR_GPCM_XACS \
+ | OR_GPCM_SCY_15 \
+ | OR_GPCM_TRLX_SET \
+ | OR_GPCM_EHTR_SET \
+ | OR_GPCM_EAD)
+ /* 0xffc06ff7 */
+#define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE
+#define CONFIG_SYS_LBLAWAR0_PRELIM (LBLAWAR_EN | LBLAWAR_4MB)
+#else
+#define CONFIG_SYS_FLASH_BASE 0xf8000000 /* start of FLASH */
+#define CONFIG_SYS_FLASH_SIZE 128 /* flash size in MB */
+#define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE | \
+ BR_PS_16 | /* 16bit */ \
+ BR_MS_GPCM | /* MSEL = GPCM */ \
+ BR_V) /* valid */
+
+#define CONFIG_SYS_OR0_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \
+ | OR_GPCM_XAM \
+ | OR_GPCM_CSNT \
+ | OR_GPCM_ACS_DIV2 \
+ | OR_GPCM_XACS \
+ | OR_GPCM_SCY_15 \
+ | OR_GPCM_TRLX_SET \
+ | OR_GPCM_EHTR_SET \
+ | OR_GPCM_EAD)
+ /* 0xf8006ff7 */
+#define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE
+#define CONFIG_SYS_LBLAWAR0_PRELIM (LBLAWAR_EN | LBLAWAR_128MB)
+#endif
+/* #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE */
+
+#define CONFIG_SYS_WINDOW1_BASE 0xf0000000
+#define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_WINDOW1_BASE \
+ | BR_PS_32 \
+ | BR_MS_GPCM \
+ | BR_V)
+ /* 0xF0001801 */
+#define CONFIG_SYS_OR1_PRELIM (OR_AM_256KB \
+ | OR_GPCM_SETA)
+ /* 0xfffc0208 */
+#define CONFIG_SYS_LBLAWBAR1_PRELIM CONFIG_SYS_WINDOW1_BASE
+#define CONFIG_SYS_LBLAWAR1_PRELIM (LBLAWAR_EN | LBLAWAR_256KB)
+
+#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */
+#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device*/
+
+#undef CONFIG_SYS_FLASH_CHECKSUM
+#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase TO (ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write TO (ms) */
+
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
+
+#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
+#define CONFIG_SYS_RAMBOOT
+#else
+#undef CONFIG_SYS_RAMBOOT
+#endif
+
+#define CONFIG_SYS_INIT_RAM_LOCK 1
+#define CONFIG_SYS_INIT_RAM_ADDR 0xF7000000 /* Initial RAM addr */
+#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* size */
+
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \
+ GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
+
+#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB */
+#define CONFIG_SYS_MALLOC_LEN (256 * 1024) /* Malloc size */
+
+/*
+ * Local Bus LCRR and LBCR regs
+ * LCRR: no DLL bypass, Clock divider is 4
+ * External Local Bus rate is
+ * CLKIN * HRCWL_CSB_TO_CLKIN / HRCWL_LCL_BUS_TO_SCB_CLK / LCRR_CLKDIV
+ */
+#define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_4
+#define CONFIG_SYS_LBC_LBCR 0x00000000
+
+#undef CONFIG_SYS_LB_SDRAM /* if board has SDRAM on local bus */
+
+/*
+ * Serial Port
+ */
+#define CONFIG_CONS_INDEX 1
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE 1
+#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
+
+#define CONFIG_SYS_BAUDRATE_TABLE \
+ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
+
+#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR + 0x4500)
+#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR + 0x4600)
+
+#define CONFIG_CMDLINE_EDITING /* add command line history */
+#define CONFIG_AUTO_COMPLETE /* add autocompletion support */
+/* Use the HUSH parser */
+#define CONFIG_SYS_HUSH_PARSER
+
+/* pass open firmware flat tree */
+#define CONFIG_OF_LIBFDT
+#define CONFIG_OF_BOARD_SETUP
+#define CONFIG_OF_STDOUT_VIA_ALIAS
+
+/* I2C */
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_FSL
+#define CONFIG_SYS_FSL_I2C_SPEED 400000
+#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
+#define CONFIG_SYS_FSL_I2C2_SPEED 400000
+#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100
+#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} }
+/* could also use CONFIG_I2C_MULTI_BUS and CONFIG_SYS_SPD_BUS_NUM... */
+
+#define CONFIG_SYS_I2C_8574_ADDR2 0x20 /* I2C1, PCF8574 */
+
+/* TSEC */
+#define CONFIG_SYS_TSEC1_OFFSET 0x24000
+#define CONFIG_SYS_TSEC1 (CONFIG_SYS_IMMR + CONFIG_SYS_TSEC1_OFFSET)
+#define CONFIG_SYS_TSEC2_OFFSET 0x25000
+#define CONFIG_SYS_TSEC2 (CONFIG_SYS_IMMR + CONFIG_SYS_TSEC2_OFFSET)
+
+/*
+ * General PCI
+ * Addresses are mapped 1-1.
+ */
+#define CONFIG_SYS_PCI1_MEM_BASE 0x80000000
+#define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BASE
+#define CONFIG_SYS_PCI1_MEM_SIZE 0x10000000 /* 256M */
+#define CONFIG_SYS_PCI1_MMIO_BASE 0x90000000
+#define CONFIG_SYS_PCI1_MMIO_PHYS CONFIG_SYS_PCI1_MMIO_BASE
+#define CONFIG_SYS_PCI1_MMIO_SIZE 0x10000000 /* 256M */
+#define CONFIG_SYS_PCI1_IO_BASE 0x00000000
+#define CONFIG_SYS_PCI1_IO_PHYS 0xE2000000
+#define CONFIG_SYS_PCI1_IO_SIZE 0x00100000 /* 1M */
+
+#define CONFIG_SYS_PCI2_MEM_BASE 0xA0000000
+#define CONFIG_SYS_PCI2_MEM_PHYS CONFIG_SYS_PCI2_MEM_BASE
+#define CONFIG_SYS_PCI2_MEM_SIZE 0x10000000 /* 256M */
+#define CONFIG_SYS_PCI2_MMIO_BASE 0xB0000000
+#define CONFIG_SYS_PCI2_MMIO_PHYS CONFIG_SYS_PCI2_MMIO_BASE
+#define CONFIG_SYS_PCI2_MMIO_SIZE 0x10000000 /* 256M */
+#define CONFIG_SYS_PCI2_IO_BASE 0x00000000
+#define CONFIG_SYS_PCI2_IO_PHYS 0xE2100000
+#define CONFIG_SYS_PCI2_IO_SIZE 0x00100000 /* 1M */
+
+#if defined(CONFIG_PCI)
+
+#define PCI_64BIT
+#define PCI_ONE_PCI1
+#if defined(PCI_64BIT)
+#undef PCI_ALL_PCI1
+#undef PCI_TWO_PCI1
+#undef PCI_ONE_PCI1
+#endif
+
+#ifndef VME_CADDY2
+#endif
+#define CONFIG_PCI_PNP /* do pci plug-and-play */
+
+#undef CONFIG_EEPRO100
+#undef CONFIG_TULIP
+
+#if !defined(CONFIG_PCI_PNP)
+ #define PCI_ENET0_IOADDR 0xFIXME
+ #define PCI_ENET0_MEMADDR 0xFIXME
+ #define PCI_IDSEL_NUMBER 0xFIXME
+#endif
+
+#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
+#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */
+
+#endif /* CONFIG_PCI */
+
+/*
+ * TSEC configuration
+ */
+#ifdef VME_CADDY2
+#define CONFIG_E1000
+#else
+#define CONFIG_TSEC_ENET /* TSEC ethernet support */
+#endif
+
+#if defined(CONFIG_TSEC_ENET)
+
+#define CONFIG_GMII /* MII PHY management */
+#define CONFIG_TSEC1
+#define CONFIG_TSEC1_NAME "TSEC0"
+#define CONFIG_TSEC2
+#define CONFIG_TSEC2_NAME "TSEC1"
+#define CONFIG_PHY_M88E1111
+#define TSEC1_PHY_ADDR 0x08
+#define TSEC2_PHY_ADDR 0x10
+#define TSEC1_PHYIDX 0
+#define TSEC2_PHYIDX 0
+#define TSEC1_FLAGS TSEC_GIGABIT
+#define TSEC2_FLAGS TSEC_GIGABIT
+
+/* Options are: TSEC[0-1] */
+#define CONFIG_ETHPRIME "TSEC0"
+
+#endif /* CONFIG_TSEC_ENET */
+
+/*
+ * Environment
+ */
+#ifndef CONFIG_SYS_RAMBOOT
+ #define CONFIG_ENV_IS_IN_FLASH
+ #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + 0xc0000)
+ #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */
+ #define CONFIG_ENV_SIZE 0x2000
+
+/* Address and size of Redundant Environment Sector */
+#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
+
+#else
+ #define CONFIG_SYS_NO_FLASH /* Flash is not usable now */
+ #define CONFIG_ENV_IS_NOWHERE /* Store ENV in memory only */
+ #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000)
+ #define CONFIG_ENV_SIZE 0x2000
+#endif
+
+#define CONFIG_LOADS_ECHO /* echo on for serial download */
+#define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_DATE
+#define CONFIG_SYS_RTC_BUS_NUM 0x01
+#define CONFIG_SYS_I2C_RTC_ADDR 0x32
+#define CONFIG_RTC_RX8025
+#define CONFIG_CMD_TSI148
+
+#if defined(CONFIG_PCI)
+ #define CONFIG_CMD_PCI
+#endif
+
+#if defined(CONFIG_SYS_RAMBOOT)
+ #undef CONFIG_CMD_ENV
+ #undef CONFIG_CMD_LOADS
+#endif
+
+#define CONFIG_CMD_ELF
+/* Pass Ethernet MAC to VxWorks */
+#define CONFIG_SYS_VXWORKS_MAC_PTR 0x000043f0
+
+#undef CONFIG_WATCHDOG /* watchdog disabled */
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
+
+#if defined(CONFIG_CMD_KGDB)
+ #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
+#else
+ #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
+#endif
+
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
+#define CONFIG_SYS_MAXARGS 16 /* max num of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buf Size */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 256 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_SYS_BOOTMAPSZ (256 << 20) /* Init Memory map for Linux*/
+
+#define CONFIG_SYS_RCWH_PCIHOST 0x80000000 /* PCIHOST */
+
+#define CONFIG_SYS_HRCW_LOW (\
+ HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
+ HRCWL_DDR_TO_SCB_CLK_1X1 |\
+ HRCWL_CSB_TO_CLKIN |\
+ HRCWL_VCO_1X2 |\
+ HRCWL_CORE_TO_CSB_2X1)
+
+#if defined(PCI_64BIT)
+#define CONFIG_SYS_HRCW_HIGH (\
+ HRCWH_PCI_HOST |\
+ HRCWH_64_BIT_PCI |\
+ HRCWH_PCI1_ARBITER_ENABLE |\
+ HRCWH_PCI2_ARBITER_DISABLE |\
+ HRCWH_CORE_ENABLE |\
+ HRCWH_FROM_0X00000100 |\
+ HRCWH_BOOTSEQ_DISABLE |\
+ HRCWH_SW_WATCHDOG_DISABLE |\
+ HRCWH_ROM_LOC_LOCAL_16BIT |\
+ HRCWH_TSEC1M_IN_GMII |\
+ HRCWH_TSEC2M_IN_GMII)
+#else
+#define CONFIG_SYS_HRCW_HIGH (\
+ HRCWH_PCI_HOST |\
+ HRCWH_32_BIT_PCI |\
+ HRCWH_PCI1_ARBITER_ENABLE |\
+ HRCWH_PCI2_ARBITER_ENABLE |\
+ HRCWH_CORE_ENABLE |\
+ HRCWH_FROM_0X00000100 |\
+ HRCWH_BOOTSEQ_DISABLE |\
+ HRCWH_SW_WATCHDOG_DISABLE |\
+ HRCWH_ROM_LOC_LOCAL_16BIT |\
+ HRCWH_TSEC1M_IN_GMII |\
+ HRCWH_TSEC2M_IN_GMII)
+#endif
+
+/* System IO Config */
+#define CONFIG_SYS_SICRH 0
+#define CONFIG_SYS_SICRL SICRL_LDP_A
+
+#define CONFIG_SYS_HID0_INIT 0x000000000
+#define CONFIG_SYS_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK | \
+ HID0_ENABLE_INSTRUCTION_CACHE)
+
+#define CONFIG_SYS_HID2 HID2_HBE
+
+#define CONFIG_SYS_GPIO1_PRELIM
+#define CONFIG_SYS_GPIO1_DIR 0x00100000
+#define CONFIG_SYS_GPIO1_DAT 0x00100000
+
+#define CONFIG_SYS_GPIO2_PRELIM
+#define CONFIG_SYS_GPIO2_DIR 0x78900000
+#define CONFIG_SYS_GPIO2_DAT 0x70100000
+
+#define CONFIG_HIGH_BATS /* High BATs supported */
+
+/* DDR @ 0x00000000 */
+#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_PP_RW | \
+ BATL_MEMCOHERENCE)
+#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE | BATU_BL_256M | \
+ BATU_VS | BATU_VP)
+
+/* PCI @ 0x80000000 */
+#ifdef CONFIG_PCI
+#define CONFIG_PCI_INDIRECT_BRIDGE
+#define CONFIG_SYS_IBAT1L (CONFIG_SYS_PCI1_MEM_BASE | BATL_PP_RW | \
+ BATL_MEMCOHERENCE)
+#define CONFIG_SYS_IBAT1U (CONFIG_SYS_PCI1_MEM_BASE | BATU_BL_256M | \
+ BATU_VS | BATU_VP)
+#define CONFIG_SYS_IBAT2L (CONFIG_SYS_PCI1_MMIO_BASE | BATL_PP_RW | \
+ BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_IBAT2U (CONFIG_SYS_PCI1_MMIO_BASE | BATU_BL_256M | \
+ BATU_VS | BATU_VP)
+#else
+#define CONFIG_SYS_IBAT1L (0)
+#define CONFIG_SYS_IBAT1U (0)
+#define CONFIG_SYS_IBAT2L (0)
+#define CONFIG_SYS_IBAT2U (0)
+#endif
+
+#ifdef CONFIG_MPC83XX_PCI2
+#define CONFIG_SYS_IBAT3L (CONFIG_SYS_PCI2_MEM_BASE | BATL_PP_RW | \
+ BATL_MEMCOHERENCE)
+#define CONFIG_SYS_IBAT3U (CONFIG_SYS_PCI2_MEM_BASE | BATU_BL_256M | \
+ BATU_VS | BATU_VP)
+#define CONFIG_SYS_IBAT4L (CONFIG_SYS_PCI2_MMIO_BASE | BATL_PP_RW | \
+ BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_IBAT4U (CONFIG_SYS_PCI2_MMIO_BASE | BATU_BL_256M | \
+ BATU_VS | BATU_VP)
+#else
+#define CONFIG_SYS_IBAT3L (0)
+#define CONFIG_SYS_IBAT3U (0)
+#define CONFIG_SYS_IBAT4L (0)
+#define CONFIG_SYS_IBAT4U (0)
+#endif
+
+/* IMMRBAR @ 0xE0000000, PCI IO @ 0xE2000000 */
+#define CONFIG_SYS_IBAT5L (CONFIG_SYS_IMMR | BATL_PP_RW | \
+ BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_IBAT5U (CONFIG_SYS_IMMR | BATU_BL_256M | \
+ BATU_VS | BATU_VP)
+
+#define CONFIG_SYS_IBAT6L (0xF0000000 | BATL_PP_RW | BATL_MEMCOHERENCE)
+#define CONFIG_SYS_IBAT6U (0xF0000000 | BATU_BL_256M | BATU_VS | BATU_VP)
+
+#if (CONFIG_SYS_DDR_SIZE == 512)
+#define CONFIG_SYS_IBAT7L (CONFIG_SYS_SDRAM_BASE+0x10000000 | \
+ BATL_PP_RW | BATL_MEMCOHERENCE)
+#define CONFIG_SYS_IBAT7U (CONFIG_SYS_SDRAM_BASE+0x10000000 | \
+ BATU_BL_256M | BATU_VS | BATU_VP)
+#else
+#define CONFIG_SYS_IBAT7L (0)
+#define CONFIG_SYS_IBAT7U (0)
+#endif
+
+#define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L
+#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U
+#define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L
+#define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U
+#define CONFIG_SYS_DBAT2L CONFIG_SYS_IBAT2L
+#define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U
+#define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L
+#define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U
+#define CONFIG_SYS_DBAT4L CONFIG_SYS_IBAT4L
+#define CONFIG_SYS_DBAT4U CONFIG_SYS_IBAT4U
+#define CONFIG_SYS_DBAT5L CONFIG_SYS_IBAT5L
+#define CONFIG_SYS_DBAT5U CONFIG_SYS_IBAT5U
+#define CONFIG_SYS_DBAT6L CONFIG_SYS_IBAT6L
+#define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U
+#define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L
+#define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U
+
+#if defined(CONFIG_CMD_KGDB)
+#define CONFIG_KGDB_BAUDRATE 230400 /* speed of kgdb serial port */
+#endif
+
+/*
+ * Environment Configuration
+ */
+#define CONFIG_ENV_OVERWRITE
+
+#if defined(CONFIG_TSEC_ENET)
+#define CONFIG_HAS_ETH0
+#define CONFIG_HAS_ETH1
+#endif
+
+#define CONFIG_HOSTNAME VME8349
+#define CONFIG_ROOTPATH "/tftpboot/rootfs"
+#define CONFIG_BOOTFILE "uImage"
+
+#define CONFIG_LOADADDR 800000 /* def location for tftp and bootm */
+
+#define CONFIG_BOOTDELAY 6 /* -1 disables auto-boot */
+#undef CONFIG_BOOTARGS /* boot command will set bootargs */
+
+#define CONFIG_BAUDRATE 9600
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "netdev=eth0\0" \
+ "hostname=vme8349\0" \
+ "nfsargs=setenv bootargs root=/dev/nfs rw " \
+ "nfsroot=${serverip}:${rootpath}\0" \
+ "ramargs=setenv bootargs root=/dev/ram rw\0" \
+ "addip=setenv bootargs ${bootargs} " \
+ "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
+ ":${hostname}:${netdev}:off panic=1\0" \
+ "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
+ "flash_nfs=run nfsargs addip addtty;" \
+ "bootm ${kernel_addr}\0" \
+ "flash_self=run ramargs addip addtty;" \
+ "bootm ${kernel_addr} ${ramdisk_addr}\0" \
+ "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \
+ "bootm\0" \
+ "load=tftp 100000 /tftpboot/bdi2000/vme8349.bin\0" \
+ "update=protect off fff00000 fff3ffff; " \
+ "era fff00000 fff3ffff; cp.b 100000 fff00000 ${filesize}\0" \
+ "upd=run load update\0" \
+ "fdtaddr=780000\0" \
+ "fdtfile=vme8349.dtb\0" \
+ ""
+
+#define CONFIG_NFSBOOTCOMMAND \
+ "setenv bootargs root=/dev/nfs rw " \
+ "nfsroot=$serverip:$rootpath " \
+ "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:" \
+ "$netdev:off " \
+ "console=$consoledev,$baudrate $othbootargs;" \
+ "tftp $loadaddr $bootfile;" \
+ "tftp $fdtaddr $fdtfile;" \
+ "bootm $loadaddr - $fdtaddr"
+
+#define CONFIG_RAMBOOTCOMMAND \
+ "setenv bootargs root=/dev/ram rw " \
+ "console=$consoledev,$baudrate $othbootargs;" \
+ "tftp $ramdiskaddr $ramdiskfile;" \
+ "tftp $loadaddr $bootfile;" \
+ "tftp $fdtaddr $fdtfile;" \
+ "bootm $loadaddr $ramdiskaddr $fdtaddr"
+
+#define CONFIG_BOOTCOMMAND "run flash_self"
+
+#ifndef __ASSEMBLY__
+int vme8349_read_spd(unsigned char chip, unsigned int addr, int alen,
+ unsigned char *buffer, int len);
+#endif
+
+#endif /* __CONFIG_H */
Code Review / kvmfornfv.git / blobdiff