--- /dev/null
+/*
+ * (C) Copyright 2003 Embedded Edge, LLC
+ * Dan Malek <dan@embeddededge.com>
+ * Copied from ADS85xx.
+ * Updates for Silicon Tx GP3 8560 board.
+ *
+ * (C) Copyright 2002,2003 Motorola,Inc.
+ * Xianghua Xiao <X.Xiao@motorola.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+/* mpc8560ads board configuration file */
+/* please refer to doc/README.mpc85xx for more info */
+/* make sure you change the MAC address and other network params first,
+ * search for CONFIG_ETHADDR,CONFIG_SERVERIP,etc in this file
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/* High Level Configuration Options */
+#define CONFIG_BOOKE 1 /* BOOKE */
+#define CONFIG_E500 1 /* BOOKE e500 family */
+#define CONFIG_CPM2 1 /* has CPM2 */
+#define CONFIG_STXGP3 1 /* Silicon Tx GPPP board specific*/
+#define CONFIG_MPC8560 1
+
+#define CONFIG_SYS_TEXT_BASE 0xfff80000
+
+#undef CONFIG_PCI /* pci ethernet support */
+#define CONFIG_TSEC_ENET /* tsec ethernet support*/
+#undef CONFIG_ETHER_ON_FCC /* cpm FCC ethernet support */
+#define CONFIG_ENV_OVERWRITE
+
+#define CONFIG_FSL_LAW 1 /* Use common FSL init code */
+
+/* sysclk for MPC85xx
+ */
+
+#define CONFIG_SYS_CLK_FREQ 33333333 /* most pci cards are 33Mhz */
+
+/* Blinkin' LEDs for Robert :-)
+*/
+#define CONFIG_SHOW_ACTIVITY 1
+
+/*
+ * These can be toggled for performance analysis, otherwise use default.
+ */
+#define CONFIG_L2_CACHE /* toggle L2 cache */
+#define CONFIG_BTB /* toggle branch predition */
+
+#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */
+#define CONFIG_RESET_PHY_R 1 /* Call reset_phy() */
+
+#undef CONFIG_SYS_DRAM_TEST /* memory test, takes time */
+#define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest region */
+#define CONFIG_SYS_MEMTEST_END 0x00400000
+
+
+/* Localbus SDRAM is an option, not all boards have it.
+ * This address, however, is used to configure a 256M local bus
+ * window that includes the Config latch below.
+ */
+#define CONFIG_SYS_LBC_SDRAM_BASE 0xf0000000 /* Localbus SDRAM */
+#define CONFIG_SYS_LBC_SDRAM_SIZE 256 /* LBC SDRAM is 64MB */
+
+#define CONFIG_SYS_FLASH_BASE 0xff000000 /* start of FLASH 16M */
+#define CONFIG_SYS_BR0_PRELIM 0xff001801 /* port size 32bit */
+
+#define CONFIG_SYS_OR0_PRELIM 0xff000ff7 /* 16 MB Flash */
+#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */
+#define CONFIG_SYS_MAX_FLASH_SECT 136 /* sectors per device */
+#undef CONFIG_SYS_FLASH_CHECKSUM
+#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Timeout for Flash Erase (in ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
+
+/* The configuration latch is Chip Select 1.
+ * It's an 8-bit latch in the lower 8 bits of the word.
+ */
+#define CONFIG_SYS_BR1_PRELIM 0xfc001801 /* 32-bit port */
+#define CONFIG_SYS_OR1_PRELIM 0xffff0ff7 /* 64K is enough */
+#define CONFIG_SYS_LBC_LCLDEVS_BASE 0xfc000000 /* Base of localbus devices */
+
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
+
+#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
+#define CONFIG_SYS_RAMBOOT
+#else
+#undef CONFIG_SYS_RAMBOOT
+#endif
+
+#ifdef CONFIG_SYS_RAMBOOT
+#define CONFIG_SYS_CCSRBAR_DEFAULT 0x40000000 /* CCSRBAR by BDI cfg */
+#endif
+#define CONFIG_SYS_CCSRBAR 0xfdf00000
+#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR
+
+/* DDR Setup */
+#define CONFIG_SYS_FSL_DDR1
+#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/
+#define CONFIG_DDR_SPD
+#undef CONFIG_FSL_DDR_INTERACTIVE
+
+#undef CONFIG_DDR_ECC /* only for ECC DDR module */
+#define CONFIG_SYS_FSL_ERRATUM_DDR_MSYNC_IN /* possible DLL fix needed */
+#define CONFIG_DDR_2T_TIMING /* Sets the 2T timing bit */
+
+#define CONFIG_MEM_INIT_VALUE 0xDeadBeef
+
+#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/
+#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
+
+#define CONFIG_NUM_DDR_CONTROLLERS 1
+#define CONFIG_DIMM_SLOTS_PER_CTLR 1
+#define CONFIG_CHIP_SELECTS_PER_CTRL (2 * CONFIG_DIMM_SLOTS_PER_CTLR)
+
+/* I2C addresses of SPD EEPROMs */
+#define SPD_EEPROM_ADDRESS 0x54 /* CTLR 0 DIMM 0 */
+
+#undef CONFIG_CLOCKS_IN_MHZ
+
+/* local bus definitions */
+#define CONFIG_SYS_BR2_PRELIM 0xf8001861 /* 64MB localbus SDRAM */
+#define CONFIG_SYS_OR2_PRELIM 0xfc006901
+#define CONFIG_SYS_LBC_LCRR 0x00030004 /* local bus freq */
+#define CONFIG_SYS_LBC_LBCR 0x00000000
+#define CONFIG_SYS_LBC_LSRT 0x20000000
+#define CONFIG_SYS_LBC_MRTPR 0x20000000
+#define CONFIG_SYS_LBC_LSDMR_1 0x2861b723
+#define CONFIG_SYS_LBC_LSDMR_2 0x0861b723
+#define CONFIG_SYS_LBC_LSDMR_3 0x0861b723
+#define CONFIG_SYS_LBC_LSDMR_4 0x1861b723
+#define CONFIG_SYS_LBC_LSDMR_5 0x4061b723
+
+#define CONFIG_SYS_INIT_RAM_LOCK 1
+#define CONFIG_SYS_INIT_RAM_ADDR 0x60000000 /* Initial RAM address */
+#define CONFIG_SYS_INIT_RAM_SIZE 0x4000 /* Size of used area in RAM */
+
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
+
+#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
+#define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserved for malloc */
+
+/* Serial Port */
+#define CONFIG_CONS_ON_SCC /* define if console on SCC */
+#undef CONFIG_CONS_NONE /* define if console on something else */
+#define CONFIG_CONS_INDEX 2 /* which serial channel for console */
+
+#define CONFIG_BAUDRATE 38400
+
+#define CONFIG_SYS_BAUDRATE_TABLE \
+ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
+
+/* Use the HUSH parser */
+#define CONFIG_SYS_HUSH_PARSER
+#ifdef CONFIG_SYS_HUSH_PARSER
+#endif
+
+/*
+ * I2C
+ */
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_FSL
+#define CONFIG_SYS_FSL_I2C_SPEED 400000
+#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
+
+#if 0
+#define CONFIG_SYS_I2C_NOPROBES {0x00} /* Don't probe these addrs */
+#else
+/* I did the 'if 0' so we could keep the syntax above if ever needed. */
+#undef CONFIG_SYS_I2C_NOPROBES
+#endif
+
+/* RapdIO Map configuration, mapped 1:1.
+*/
+#define CONFIG_SYS_RIO_MEM_BASE 0xc0000000
+#define CONFIG_SYS_RIO_MEM_PHYS CONFIG_SYS_RIO_MEM_BASE
+#define CONFIG_SYS_RIO_MEM_SIZE 0x200000000 /* 512 M */
+
+/* Standard 8560 PCI addressing, mapped 1:1.
+*/
+#define CONFIG_SYS_PCI1_MEM_BASE 0x80000000
+#define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BASE
+#define CONFIG_SYS_PCI1_MEM_SIZE 0x20000000 /* 512M */
+#define CONFIG_SYS_PCI1_IO_BASE 0xe2000000
+#define CONFIG_SYS_PCI1_IO_PHYS CONFIG_SYS_PCI1_IO_BASE
+#define CONFIG_SYS_PCI1_IO_SIZE 0x01000000 /* 16 M */
+
+#if defined(CONFIG_PCI) /* PCI Ethernet card */
+
+#define CONFIG_PCI_PNP /* do pci plug-and-play */
+
+#undef CONFIG_EEPRO100
+#undef CONFIG_TULIP
+
+#if !defined(CONFIG_PCI_PNP)
+ #define PCI_ENET0_IOADDR 0xe0000000
+ #define PCI_ENET0_MEMADDR 0xe0000000
+ #define PCI_IDSEL_NUMBER 0x0c /* slot0->3(IDSEL)=12->15 */
+#endif
+
+#undef CONFIG_PCI_SCAN_SHOW
+#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1057 /* Motorola */
+
+#endif /* CONFIG_PCI */
+
+#if defined(CONFIG_TSEC_ENET)
+
+#define CONFIG_MII 1 /* MII PHY management */
+
+#define CONFIG_TSEC1 1
+#define CONFIG_TSEC1_NAME "TSEC0"
+#define CONFIG_TSEC2 1
+#define CONFIG_TSEC2_NAME "TSEC1"
+
+#define TSEC1_PHY_ADDR 2
+#define TSEC2_PHY_ADDR 4
+#define TSEC1_PHYIDX 0
+#define TSEC2_PHYIDX 0
+#define TSEC1_FLAGS TSEC_GIGABIT
+#define TSEC2_FLAGS TSEC_GIGABIT
+#define CONFIG_ETHPRIME "TSEC0"
+
+#elif defined(CONFIG_ETHER_ON_FCC) /* CPM FCC Ethernet */
+
+#define CONFIG_ETHER_ON_FCC2 /* define if ether on FCC */
+#undef CONFIG_ETHER_NONE /* define if ether on something else */
+#define CONFIG_ETHER_INDEX 2 /* which channel for ether */
+
+#if (CONFIG_ETHER_INDEX == 2)
+ /*
+ * - Rx-CLK is CLK13
+ * - Tx-CLK is CLK14
+ * - Select bus for bd/buffers
+ * - Full duplex
+ */
+ #define CONFIG_SYS_CMXFCR_MASK2 (CMXFCR_FC2 | CMXFCR_RF2CS_MSK | CMXFCR_TF2CS_MSK)
+ #define CONFIG_SYS_CMXFCR_VALUE2 (CMXFCR_RF2CS_CLK13 | CMXFCR_TF2CS_CLK14)
+ #define CONFIG_SYS_CPMFCR_RAMTYPE 0
+#if 0
+ #define CONFIG_SYS_FCC_PSMR (FCC_PSMR_FDE)
+#else
+ #define CONFIG_SYS_FCC_PSMR 0
+#endif
+ #define FETH2_RST 0x01
+#elif (CONFIG_ETHER_INDEX == 3)
+ /* need more definitions here for FE3 */
+ #define FETH3_RST 0x80
+#endif /* CONFIG_ETHER_INDEX */
+
+/* MDIO is done through the TSEC0 control.
+*/
+#define CONFIG_MII /* MII PHY management */
+#undef CONFIG_BITBANGMII /* bit-bang MII PHY management */
+
+#endif
+
+/* Environment */
+/* We use the top boot sector flash, so we have some 16K sectors for env
+ */
+#ifndef CONFIG_SYS_RAMBOOT
+ #define CONFIG_ENV_IS_IN_FLASH 1
+ #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + 0x60000)
+ #define CONFIG_ENV_SECT_SIZE 0x4000 /* 16K (one top sector) for env */
+ #define CONFIG_ENV_SIZE 0x2000
+#else
+ #define CONFIG_SYS_NO_FLASH 1 /* Flash is not usable now */
+ #define CONFIG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */
+ #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000)
+ #define CONFIG_ENV_SIZE 0x2000
+#endif
+
+#define CONFIG_BOOTARGS "root=/dev/nfs rw ip=any console=ttyS1,38400"
+#define CONFIG_BOOTCOMMAND "bootm 0xff000000 0xff100000"
+#define CONFIG_BOOTDELAY 3 /* -1 disable autoboot */
+
+#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
+#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_REGINFO
+
+#if defined(CONFIG_SYS_RAMBOOT)
+ #undef CONFIG_CMD_SAVEENV
+ #undef CONFIG_CMD_LOADS
+#else
+ #define CONFIG_CMD_ELF
+#endif
+
+#if defined(CONFIG_PCI)
+ #define CONFIG_CMD_PCI
+#endif
+
+#if defined(CONFIG_TSEC_ENET) || defined(CONFIG_ETHER_ON_FCC)
+ #define CONFIG_CMD_MII
+#endif
+
+
+#undef CONFIG_WATCHDOG /* watchdog disabled */
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#define CONFIG_SYS_PROMPT "GPPP=> " /* Monitor Command Prompt */
+#if defined(CONFIG_CMD_KGDB)
+#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
+#else
+#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
+#endif
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
+#define CONFIG_SYS_LOAD_ADDR 0x1000000 /* default load address */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+
+#if defined(CONFIG_CMD_KGDB)
+#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
+#endif
+
+/*Note: change below for your network setting!!! */
+#if defined(CONFIG_TSEC_ENET) || defined(CONFIG_ETHER_ON_FCC)
+#define CONFIG_HAS_ETH0
+#define CONFIG_ETHADDR 00:e0:0c:07:9b:8a
+#define CONFIG_HAS_ETH1
+#define CONFIG_ETH1ADDR 00:e0:0c:07:9b:8b
+#define CONFIG_HAS_ETH2
+#define CONFIG_ETH2ADDR 00:e0:0c:07:9b:8c
+#endif
+
+#define CONFIG_SERVERIP 192.168.85.1
+#define CONFIG_IPADDR 192.168.85.60
+#define CONFIG_GATEWAYIP 192.168.85.1
+#define CONFIG_NETMASK 255.255.255.0
+#define CONFIG_HOSTNAME STX_GP3
+#define CONFIG_ROOTPATH "/gppproot"
+#define CONFIG_BOOTFILE "uImage"
+#define CONFIG_LOADADDR 0x1000000
+
+#endif /* __CONFIG_H */
Code Review / kvmfornfv.git / blobdiff