--- /dev/null
+/*
+ * Copyright (C) ST-Ericsson SA 2009
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * #define DEBUG 1
+ */
+
+#define CONFIG_SKIP_LOWLEVEL_INIT
+#define CONFIG_SNOWBALL
+#define CONFIG_SYS_ICACHE_OFF
+#define CONFIG_SYS_DCACHE_OFF
+#define CONFIG_ARCH_CPU_INIT
+#define CONFIG_BOARD_LATE_INIT
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+#define CONFIG_U8500
+
+#define CONFIG_SYS_MEMTEST_START 0x00000000
+#define CONFIG_SYS_MEMTEST_END 0x1FFFFFFF
+
+/*-----------------------------------------------------------------------
+ * Size of environment and malloc() pool
+ */
+/*
+ * If you use U-Boot as crash kernel, make sure that it does not overwrite
+ * information saved by kexec during panic. Kexec expects the start
+ * address of the executable 32K above "crashkernel" address.
+ */
+/*
+ * Size of malloc() pool
+ */
+#define CONFIG_ENV_SIZE (8*1024)
+#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 256*1024)
+
+#define CONFIG_ENV_IS_IN_MMC
+#define CONFIG_CMD_ENV
+#define CONFIG_CMD_SAVEENV
+#define CONFIG_ENV_OFFSET 0x0118000
+#define CONFIG_SYS_MMC_ENV_DEV 0 /* SLOT2: eMMC */
+
+/*
+ * PL011 Configuration
+ */
+#define CONFIG_PL011_SERIAL
+#define CONFIG_PL011_SERIAL_RLCR
+#define CONFIG_PL011_SERIAL_FLUSH_ON_INIT
+
+/*
+ * U8500 UART registers base for 3 serial devices
+ */
+#define CFG_UART0_BASE 0x80120000
+#define CFG_UART1_BASE 0x80121000
+#define CFG_UART2_BASE 0x80007000
+#define CFG_SERIAL0 CFG_UART0_BASE
+#define CFG_SERIAL1 CFG_UART1_BASE
+#define CFG_SERIAL2 CFG_UART2_BASE
+#define CONFIG_PL011_CLOCK 38400000
+#define CONFIG_PL01x_PORTS { (void *)CFG_SERIAL0, (void *)CFG_SERIAL1, \
+ (void *)CFG_SERIAL2 }
+#define CONFIG_CONS_INDEX 2
+#define CONFIG_BAUDRATE 115200
+
+/*
+ * Devices and file systems
+ */
+#define CONFIG_MMC
+#define CONFIG_GENERIC_MMC
+#define CONFIG_DOS_PARTITION
+
+/*
+ * Commands
+ */
+#define CONFIG_CMD_MEMORY
+#define CONFIG_CMD_BOOTD
+#define CONFIG_CMD_BDI
+#define CONFIG_CMD_IMI
+#define CONFIG_CMD_MISC
+#define CONFIG_CMD_RUN
+#define CONFIG_CMD_ECHO
+#define CONFIG_CMD_CONSOLE
+#define CONFIG_CMD_LOADS
+#define CONFIG_CMD_LOADB
+#define CONFIG_CMD_MMC
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_EXT2
+#define CONFIG_CMD_SOURCE
+
+#ifndef CONFIG_BOOTDELAY
+#define CONFIG_BOOTDELAY 1
+#endif
+#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
+
+#undef CONFIG_BOOTARGS
+#define CONFIG_BOOTCOMMAND \
+"mmc dev 1; " \
+ "if run loadbootscript; " \
+ "then run bootscript; " \
+ "else " \
+ "if run mmcload; " \
+ "then run mmcboot; " \
+ "else " \
+ "mmc dev 0; " \
+ "if run emmcloadbootscript; " \
+ "then run bootscript; " \
+ "else " \
+ "if run emmcload; " \
+ "then run emmcboot; " \
+ "else " \
+ "echo No media to boot from; " \
+ "fi; " \
+ "fi; " \
+ "fi; " \
+ "fi; "
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "verify=n\0" \
+ "loadaddr=0x00100000\0" \
+ "console=ttyAMA2,115200n8\0" \
+ "loadbootscript=fatload mmc 1:1 ${loadaddr} boot.scr\0" \
+ "emmcloadbootscript=fatload mmc 0:2 ${loadaddr} boot.scr\0" \
+ "bootscript=echo Running bootscript " \
+ "from mmc ...; source ${loadaddr}\0" \
+ "memargs256=mem=96M@0 mem_modem=32M@96M mem=32M@128M " \
+ "hwmem=22M@160M pmem_hwb=42M@182M mem_mali=32@224M\0" \
+ "memargs512=mem=96M@0 mem_modem=32M@96M hwmem=32M@128M " \
+ "mem=64M@160M mem_mali=32M@224M " \
+ "pmem_hwb=128M@256M mem=128M@384M\0" \
+ "memargs1024=mem=128M@0 mali.mali_mem=32M@128M " \
+ "hwmem=168M@M160M mem=48M@328M " \
+ "mem_issw=1M@383M mem=640M@384M\0" \
+ "memargs=setenv bootargs ${bootargs} ${memargs1024}\0" \
+ "emmcload=fatload mmc 0:2 ${loadaddr} uImage\0" \
+ "mmcload=fatload mmc 1:1 ${loadaddr} uImage\0" \
+ "commonargs=setenv bootargs console=${console} " \
+ "vmalloc=300M\0" \
+ "emmcargs=setenv bootargs ${bootargs} " \
+ "root=/dev/mmcblk0p3 " \
+ "rootwait\0" \
+ "addcons=setenv bootargs ${bootargs} " \
+ "console=${console}\0" \
+ "emmcboot=echo Booting from eMMC ...; " \
+ "run commonargs emmcargs memargs; " \
+ "bootm ${loadaddr}\0" \
+ "mmcargs=setenv bootargs ${bootargs} " \
+ "root=/dev/mmcblk1p2 " \
+ "rootwait earlyprintk\0" \
+ "mmcboot=echo Booting from external MMC ...; " \
+ "run commonargs mmcargs memargs; " \
+ "bootm ${loadaddr}\0" \
+ "fdt_high=0x2BC00000\0" \
+ "stdout=serial,usbtty\0" \
+ "stdin=serial,usbtty\0" \
+ "stderr=serial,usbtty\0"
+
+/*-----------------------------------------------------------------------
+ * Miscellaneous configurable options
+ */
+
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#define CONFIG_SYS_PROMPT "U8500 $ " /* Monitor Command Prompt */
+#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
+
+/* Print Buffer Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE \
+ + sizeof(CONFIG_SYS_PROMPT) + 16)
+#define CONFIG_SYS_MAXARGS 32 /* max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Arg Buffer Size */
+
+#undef CONFIG_SYS_CLKS_IN_HZ /* everything, incl board info, in Hz */
+#define CONFIG_SYS_LOAD_ADDR 0x00100000 /* default load address */
+#define CONFIG_SYS_LOADS_BAUD_CHANGE 1
+
+#define CONFIG_SYS_HUSH_PARSER 1
+#define CONFIG_CMDLINE_EDITING
+
+#define CONFIG_SETUP_MEMORY_TAGS 2
+#define CONFIG_INITRD_TAG 1
+#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */
+
+/*
+ * Physical Memory Map
+ */
+#define CONFIG_NR_DRAM_BANKS 1
+#define PHYS_SDRAM_1 0x00000000 /* DDR-SDRAM Bank #1 */
+
+/*
+ * additions for new relocation code
+ */
+#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
+#define CONFIG_SYS_MAX_RAM_SIZE 0x40000000
+#define CONFIG_SYS_INIT_RAM_SIZE 0x100000
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_SDRAM_BASE + \
+ CONFIG_SYS_INIT_RAM_SIZE - \
+ GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_ADDR CONFIG_SYS_GBL_DATA_OFFSET
+
+/* landing address before relocation */
+#ifndef CONFIG_SYS_TEXT_BASE
+#define CONFIG_SYS_TEXT_BASE 0x0
+#endif
+
+/*
+ * MMC related configs
+ */
+#define CONFIG_ARM_PL180_MMCI
+#define MMC_BLOCK_SIZE 512
+#define CFG_EMMC_BASE 0x80114000
+#define CFG_MMC_BASE 0x80126000
+
+/*
+ * FLASH and environment organization
+ */
+#define CONFIG_SYS_NO_FLASH
+
+/*
+ * base register values for U8500
+ */
+#define CFG_PRCMU_BASE 0x80157000 /* Power, reset and clock */
+
+
+/*
+ * U8500 GPIO register base for 9 banks
+ */
+#define CONFIG_DB8500_GPIO
+#define CFG_GPIO_0_BASE 0x8012E000
+#define CFG_GPIO_1_BASE 0x8012E080
+#define CFG_GPIO_2_BASE 0x8000E000
+#define CFG_GPIO_3_BASE 0x8000E080
+#define CFG_GPIO_4_BASE 0x8000E100
+#define CFG_GPIO_5_BASE 0x8000E180
+#define CFG_GPIO_6_BASE 0x8011E000
+#define CFG_GPIO_7_BASE 0x8011E080
+#define CFG_GPIO_8_BASE 0xA03FE000
+
+#define CFG_FSMC_BASE 0x80000000 /* FSMC Controller */
+
+#endif /* __CONFIG_H */
Code Review / kvmfornfv.git / blobdiff