Add qemu 2.4.0

[kvmfornfv.git] / qemu / roms / u-boot / include / configs / sc_sps_1.h

diff --git a/qemu/roms/u-boot/include/configs/sc_sps_1.h b/qemu/roms/u-boot/include/configs/sc_sps_1.h
new file mode 100644 (file)
index 0000000..16d2e2d
--- /dev/null
+++ b/qemu/roms/u-boot/include/configs/sc_sps_1.h
@@ -0,0 +1,91 @@
+/*
+ * SchulerControl GmbH, SC_SPS_1 module config
+ *
+ * Copyright (C) 2012 Marek Vasut <marex@denx.de>
+ * on behalf of DENX Software Engineering GmbH
+ *
+ * SPDX-License-Identifier:    GPL-2.0+
+ */
+#ifndef __CONFIGS_SC_SPS_1_H__
+#define __CONFIGS_SC_SPS_1_H__
+
+/* System configuration */
+#define CONFIG_MX28                            /* i.MX28 SoC */
+#define MACH_TYPE_SC_SPS_1     4172
+#define CONFIG_MACH_TYPE       MACH_TYPE_SC_SPS_1
+
+/* U-Boot Commands */
+#define CONFIG_SYS_NO_FLASH
+#include <config_cmd_default.h>
+#define CONFIG_DISPLAY_CPUINFO
+#define CONFIG_DOS_PARTITION
+
+#define CONFIG_CMD_CACHE
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_EXT2
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_GPIO
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_MMC
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_NFS
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_SETEXPR
+#define CONFIG_CMD_USB
+
+/* Memory configuration */
+#define CONFIG_NR_DRAM_BANKS           1               /* 1 bank of DRAM */
+#define PHYS_SDRAM_1                   0x40000000      /* Base address */
+#define PHYS_SDRAM_1_SIZE              0x40000000      /* Max 1 GB RAM */
+#define CONFIG_SYS_SDRAM_BASE          PHYS_SDRAM_1
+
+/* Environment */
+#define CONFIG_ENV_SIZE                        (16 * 1024)
+#define CONFIG_ENV_IS_IN_MMC
+
+/* Environment is in MMC */
+#if defined(CONFIG_CMD_MMC) && defined(CONFIG_ENV_IS_IN_MMC)
+#define CONFIG_ENV_OFFSET              (256 * 1024)
+#define CONFIG_SYS_MMC_ENV_DEV         0
+#else
+#define CONFIG_ENV_IS_NOWHERE
+#endif
+
+/* FEC Ethernet on SoC */
+#ifdef CONFIG_CMD_NET
+#define CONFIG_FEC_MXC
+#define CONFIG_PHYLIB
+#define CONFIG_PHY_SMSC
+#endif
+
+/* USB */
+#ifdef CONFIG_CMD_USB
+#define CONFIG_EHCI_MXS_PORT0
+#define CONFIG_USB_MAX_CONTROLLER_COUNT        1
+#define CONFIG_USB_STORAGE
+#endif
+
+/* Booting Linux */
+#define CONFIG_BOOTDELAY       3
+#define CONFIG_BOOTFILE                "uImage"
+#define CONFIG_BOOTARGS                "console=ttyAMA0,115200"
+#define CONFIG_BOOTCOMMAND     "bootm"
+#define CONFIG_LOADADDR                0x42000000
+#define CONFIG_SYS_LOAD_ADDR   CONFIG_LOADADDR
+
+/* Extra Environment */
+#define CONFIG_EXTRA_ENV_SETTINGS                                      \
+       "update_sd_firmware_filename=u-boot.sd\0"                       \
+       "update_sd_firmware="           /* Update the SD firmware partition */ \
+               "if mmc rescan ; then "                                 \
+               "if tftp ${update_sd_firmware_filename} ; then "        \
+               "setexpr fw_sz ${filesize} / 0x200 ; "  /* SD block size */ \
+               "setexpr fw_sz ${fw_sz} + 1 ; "                         \
+               "mmc write ${loadaddr} 0x800 ${fw_sz} ; "               \
+               "fi ; "                                                 \
+               "fi\0"
+
+/* The rest of the configuration is shared */
+#include <configs/mxs.h>
+
+#endif /* __CONFIGS_SC_SPS_1_H__ */