--- /dev/null
+/*
+ * (C) Copyright 2003-2010
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+/*
+ * board/config.h - configuration options, board specific
+ * changes for 16M board
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+
+#undef CONFIG_MPC860
+#define CONFIG_MPC850 1 /* This is a MPC850 CPU */
+#define CONFIG_RPXLITE 1 /* QUANTUM is the RPXlite clone */
+#define CONFIG_RMU 1 /* The QUNATUM is based on our RMU */
+
+#define CONFIG_SYS_TEXT_BASE 0xfff00000
+
+#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */
+#undef CONFIG_8xx_CONS_SMC2
+#undef CONFIG_8xx_CONS_NONE
+#define CONFIG_BAUDRATE 9600 /* console baudrate = 9600bps */
+#if 0
+#define CONFIG_BOOTDELAY -1 /* autoboot disabled */
+#else
+#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
+#endif
+
+/* default developmenmt environment */
+
+#define CONFIG_ETHADDR 00:0B:17:00:00:00
+
+#define CONFIG_IPADDR 10.10.69.10
+#define CONFIG_SERVERIP 10.10.69.49
+#define CONFIG_NETMASK 255.255.255.0
+#define CONFIG_HOSTNAME QUANTUM
+#define CONFIG_ROOTPATH "/opt/eldk/pcc_8xx"
+
+#define CONFIG_BOOTARGS "root=/dev/ram rw"
+
+#define CONFIG_BOOTCOMMAND "bootm ff000000"
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "serial#=12345\0" \
+ "nfsargs=setenv bootargs root=/dev/nfs rw nfsroot=${serverip}:${rootpath}\0" \
+ "ramargs=setenv bootargs root=/dev/ram rw\0" \
+ "addip=setenv bootargs ${bootargs} ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off\0"
+
+/*
+ * Select the more full-featured memory test (Barr embedded systems)
+ */
+#define CONFIG_SYS_ALT_MEMTEST
+
+#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
+#undef CONFIG_SYS_LOADS_BAUD_CHANGE /* don't allow baudrate change */
+
+
+/* M48T02 Paralled access timekeeper with same interface as the M48T35A*/
+#define CONFIG_RTC_M48T35A 1
+
+#if 0
+#define CONFIG_WATCHDOG 1 /* watchdog enabled */
+#else
+#undef CONFIG_WATCHDOG
+#endif
+
+/* NVRAM and RTC */
+#define CONFIG_SYS_NVRAM_BASE_ADDR 0xFA000000
+#define CONFIG_SYS_NVRAM_SIZE 2048
+
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_DATE
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_NFS
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_REGINFO
+#define CONFIG_CMD_SNTP
+
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_SUBNETMASK
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_BOOTFILESIZE
+
+
+#define CONFIG_AUTOBOOT_KEYED /* Enable password protection */
+#define CONFIG_AUTOBOOT_PROMPT \
+ "\nEnter password - autoboot in %d sec...\n", bootdelay
+#define CONFIG_AUTOBOOT_DELAY_STR "system"
+/*
+ * Miscellaneous configurable options
+ */
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#if defined(CONFIG_CMD_KGDB)
+#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
+#else
+#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
+#endif
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
+
+#define CONFIG_SYS_MEMTEST_START 0x00040000 /* memtest works on */
+#define CONFIG_SYS_MEMTEST_END 0x01f00000 /* 256K ... 15 MB in DRAM */
+
+#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
+
+/*
+ * Low Level Configuration Settings
+ * (address mappings, register initial values, etc.)
+ * You should know what you are doing if you make changes here.
+ */
+/*-----------------------------------------------------------------------
+ * Internal Memory Mapped Register
+ */
+#define CONFIG_SYS_IMMR 0xFA200000
+
+/*-----------------------------------------------------------------------
+ * Definitions for initial stack pointer and data area (in DPRAM)
+ */
+#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR
+#define CONFIG_SYS_INIT_RAM_SIZE 0x2F00 /* Size of used area in DPRAM */
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
+
+/*-----------------------------------------------------------------------
+ * Start addresses for the final memory configuration
+ * (Set up by the startup code)
+ * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
+ */
+#define CONFIG_SYS_SDRAM_BASE 0x00000000
+#define CONFIG_SYS_FLASH_BASE 0xFF000000
+
+#if 1
+ #define CONFIG_FLASH_CFI_DRIVER
+#else
+ #undef CONFIG_FLASH_CFI_DRIVER
+#endif
+
+
+#ifdef CONFIG_FLASH_CFI_DRIVER
+ #define CONFIG_SYS_FLASH_CFI 1
+ #undef CONFIG_SYS_FLASH_USE_BUFFER_WRITE
+ #define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE}
+#endif
+
+/*%%% #define CONFIG_SYS_FLASH_BASE 0xFFF00000 */
+#if defined(DEBUG) || defined(CONFIG_CMD_IDE)
+#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
+#else
+#define CONFIG_SYS_MONITOR_LEN (128 << 10) /* Reserve 128 kB for Monitor */
+#endif
+#define CONFIG_SYS_MONITOR_BASE 0xFFF00000
+/*%%% #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE */
+#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+
+/*-----------------------------------------------------------------------
+ * FLASH organization
+ */
+#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
+#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max number of sectors on one chip */
+
+#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
+
+#define CONFIG_ENV_IS_IN_FLASH 1
+#define CONFIG_ENV_OFFSET 0x00040000 /* Offset of Environment Sector absolute address 0xfff40000*/
+#define CONFIG_ENV_SECT_SIZE 0x40000 /* Total Size of Environment Sector */
+#define CONFIG_ENV_SIZE CONFIG_ENV_SECT_SIZE
+#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + CONFIG_ENV_OFFSET)
+
+/* Address and size of Redundant Environment Sector */
+#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET+CONFIG_ENV_SIZE)
+#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
+
+/* FPGA */
+#define CONFIG_MISC_INIT_R
+#define CONFIG_SYS_FPGA_SPARTAN2
+#define CONFIG_SYS_FPGA_PROG_FEEDBACK
+
+
+/*-----------------------------------------------------------------------
+ * Reset address
+ */
+#define CONFIG_SYS_RESET_ADDRESS ((ulong)((((immap_t *)CONFIG_SYS_IMMR)->im_clkrst.res)))
+
+/*-----------------------------------------------------------------------
+ * Cache Configuration
+ */
+#define CONFIG_SYS_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */
+#if defined(CONFIG_CMD_KGDB)
+#define CONFIG_SYS_CACHELINE_SHIFT 4 /* log base 2 of the above value */
+#endif
+
+/*-----------------------------------------------------------------------
+ * SYPCR - System Protection Control 11-9
+ * SYPCR can only be written once after reset!
+ *-----------------------------------------------------------------------
+ * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
+ */
+#if defined(CONFIG_WATCHDOG)
+#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
+ SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP)
+#else
+#define CONFIG_SYS_SYPCR (SYPCR_SWTC | 0x00000600 | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
+#endif
+
+/*-----------------------------------------------------------------------
+ * SIUMCR - SIU Module Configuration 11-6
+ *-----------------------------------------------------------------------
+ * PCMCIA config., multi-function pin tri-state
+ */
+#define CONFIG_SYS_SIUMCR (SIUMCR_MLRC10)
+
+/*-----------------------------------------------------------------------
+ * TBSCR - Time Base Status and Control 11-26
+ *-----------------------------------------------------------------------
+ * Clear Reference Interrupt Status, Timebase freezing enabled
+ */
+#define CONFIG_SYS_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF | TBSCR_TBE)
+
+/*-----------------------------------------------------------------------
+ * RTCSC - Real-Time Clock Status and Control Register 11-27
+ *-----------------------------------------------------------------------
+ */
+/*%%%#define CONFIG_SYS_RTCSC (RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE) */
+#define CONFIG_SYS_RTCSC (RTCSC_SEC | RTCSC_RTE)
+
+/*-----------------------------------------------------------------------
+ * PISCR - Periodic Interrupt Status and Control 11-31
+ *-----------------------------------------------------------------------
+ * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
+ */
+#define CONFIG_SYS_PISCR (PISCR_PS | PISCR_PITF)
+
+/*-----------------------------------------------------------------------
+ * PLPRCR - PLL, Low-Power, and Reset Control Register 15-30
+ *-----------------------------------------------------------------------
+ * Reset PLL lock status sticky bit, timer expired status bit and timer
+ * interrupt status bit
+ *
+ * If this is a 80 MHz CPU, set PLL multiplication factor to 5 (5*16=80)!
+ */
+/* up to 50 MHz we use a 1:1 clock */
+#define CONFIG_SYS_PLPRCR ( (5 << PLPRCR_MF_SHIFT) | PLPRCR_TEXPS )
+
+/*-----------------------------------------------------------------------
+ * SCCR - System Clock and reset Control Register 15-27
+ *-----------------------------------------------------------------------
+ * Set clock output, timebase and RTC source and divider,
+ * power management and some other internal clocks
+ */
+#define SCCR_MASK SCCR_EBDF00
+/* up to 50 MHz we use a 1:1 clock */
+#define CONFIG_SYS_SCCR (SCCR_COM00 | SCCR_TBS)
+
+/*-----------------------------------------------------------------------
+ * PCMCIA stuff
+ *-----------------------------------------------------------------------
+ *
+ */
+#define CONFIG_SYS_PCMCIA_MEM_ADDR (0xE0000000)
+#define CONFIG_SYS_PCMCIA_MEM_SIZE ( 64 << 20 )
+#define CONFIG_SYS_PCMCIA_DMA_ADDR (0xE4000000)
+#define CONFIG_SYS_PCMCIA_DMA_SIZE ( 64 << 20 )
+#define CONFIG_SYS_PCMCIA_ATTRB_ADDR (0xE8000000)
+#define CONFIG_SYS_PCMCIA_ATTRB_SIZE ( 64 << 20 )
+#define CONFIG_SYS_PCMCIA_IO_ADDR (0xEC000000)
+#define CONFIG_SYS_PCMCIA_IO_SIZE ( 64 << 20 )
+
+/*-----------------------------------------------------------------------
+ * IDE/ATA stuff (Supports IDE harddisk on PCMCIA Adapter)
+ *-----------------------------------------------------------------------
+ */
+
+#define CONFIG_IDE_PREINIT 1 /* Use preinit IDE hook */
+#define CONFIG_IDE_8xx_PCCARD 1 /* Use IDE with PC Card Adapter */
+
+#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */
+#undef CONFIG_IDE_LED /* LED for ide not supported */
+#undef CONFIG_IDE_RESET /* reset for ide not supported */
+
+#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */
+#define CONFIG_SYS_IDE_MAXDEVICE 1 /* max. 1 drive per IDE bus */
+
+#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000
+
+#define CONFIG_SYS_ATA_BASE_ADDR CONFIG_SYS_PCMCIA_MEM_ADDR
+
+/* Offset for data I/O */
+#define CONFIG_SYS_ATA_DATA_OFFSET (CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
+
+/* Offset for normal register accesses */
+#define CONFIG_SYS_ATA_REG_OFFSET (2 * CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
+
+/* Offset for alternate registers */
+#define CONFIG_SYS_ATA_ALT_OFFSET 0x0100
+
+/*-----------------------------------------------------------------------
+ *
+ *-----------------------------------------------------------------------
+ *
+ */
+/*#define CONFIG_SYS_DER 0x2002000F*/
+#define CONFIG_SYS_DER 0
+
+/*
+ * Init Memory Controller:
+ *
+ * BR0 and OR0 (FLASH)
+ */
+
+#define FLASH_BASE_PRELIM 0xFE000000 /* FLASH base */
+#define CONFIG_SYS_PRELIM_OR_AM 0xFE000000 /* OR addr mask */
+
+/* FLASH timing: ACS = 0, TRLX = 0, CSNT = 0, SCY = 4, ETHR = 0, BIH = 1 */
+#define CONFIG_SYS_OR_TIMING_FLASH (OR_SCY_4_CLK | OR_BI)
+
+#define CONFIG_SYS_OR0_PRELIM (CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_FLASH)
+#define CONFIG_SYS_BR0_PRELIM ((FLASH_BASE_PRELIM & BR_BA_MSK) | BR_V)
+
+/*
+ * BR1 and OR1 (SDRAM)
+ *
+ */
+#define SDRAM_BASE_PRELIM 0x00000000 /* SDRAM base */
+#define SDRAM_MAX_SIZE 0x08000000 /* max 128 MB */
+
+/* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care) */
+#define CONFIG_SYS_OR_TIMING_SDRAM 0x00000E00
+
+#define CONFIG_SYS_OR1_PRELIM (0xF0000000 | CONFIG_SYS_OR_TIMING_SDRAM ) /* map 256 MB */
+#define CONFIG_SYS_BR1_PRELIM ((SDRAM_BASE_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
+
+/* RPXLITE mem setting */
+#define CONFIG_SYS_BR3_PRELIM 0xFA400001 /* FPGA */
+#define CONFIG_SYS_OR3_PRELIM 0xFFFF8910
+
+#define CONFIG_SYS_BR4_PRELIM 0xFA000401 /* NVRAM&SRAM */
+#define CONFIG_SYS_OR4_PRELIM 0xFFFE0970
+
+/*
+ * Memory Periodic Timer Prescaler
+ */
+
+/* periodic timer for refresh */
+#define CONFIG_SYS_MAMR_PTA 20
+
+/*
+ * Refresh clock Prescalar
+ */
+#define CONFIG_SYS_MPTPR MPTPR_PTP_DIV2
+
+/*
+ * MAMR settings for SDRAM
+ */
+
+/* 9 column SDRAM */
+#define CONFIG_SYS_MAMR_9COL ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \
+ MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 | \
+ MAMR_RLFA_16X | MAMR_WLFA_16X | MAMR_TLFA_16X)
+
+/*
+ * BCSRx
+ *
+ * Board Status and Control Registers
+ *
+ */
+
+#define BCSR0 0xFA400000
+#define BCSR1 0xFA400001
+#define BCSR2 0xFA400002
+#define BCSR3 0xFA400003
+
+#define BCSR0_ENMONXCVR 0x01 /* Monitor XVCR Control */
+#define BCSR0_ENNVRAM 0x02 /* CS4# Control */
+#define BCSR0_LED5 0x04 /* LED5 control 0='on' 1='off' */
+#define BCSR0_LED4 0x08 /* LED4 control 0='on' 1='off' */
+#define BCSR0_FULLDPLX 0x10 /* Ethernet XCVR Control */
+#define BCSR0_COLTEST 0x20
+#define BCSR0_ETHLPBK 0x40
+#define BCSR0_ETHEN 0x80
+
+#define BCSR1_PCVCTL7 0x01 /* PC Slot B Control */
+#define BCSR1_PCVCTL6 0x02
+#define BCSR1_PCVCTL5 0x04
+#define BCSR1_PCVCTL4 0x08
+#define BCSR1_IPB5SEL 0x10
+
+#define BCSR2_ENPA5HDR 0x08 /* USB Control */
+#define BCSR2_ENUSBCLK 0x10
+#define BCSR2_USBPWREN 0x20
+#define BCSR2_USBSPD 0x40
+#define BCSR2_USBSUSP 0x80
+
+#define BCSR3_BWRTC 0x01 /* Real Time Clock Battery */
+#define BCSR3_BWNVR 0x02 /* NVRAM Battery */
+#define BCSR3_RDY_BSY 0x04 /* Flash Operation */
+#define BCSR3_RPXL 0x08 /* Reserved (reads back '1') */
+#define BCSR3_D27 0x10 /* Dip Switch settings */
+#define BCSR3_D26 0x20
+#define BCSR3_D25 0x40
+#define BCSR3_D24 0x80
+
+#endif /* __CONFIG_H */
Code Review / kvmfornfv.git / blobdiff