--- /dev/null
+/*
+ * (C) Copyright 2008
+ * Gary Jennejohn, DENX Software Engineering GmbH, garyj@denx.de.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+/************************************************************************
+ * quad100hd.h - configuration for Quad100hd board
+ ***********************************************************************/
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*-----------------------------------------------------------------------
+ * High Level Configuration Options
+ *----------------------------------------------------------------------*/
+#define CONFIG_QUAD100HD 1 /* Board is Quad100hd */
+#define CONFIG_405EP 1 /* Specifc 405EP support*/
+
+#define CONFIG_SYS_TEXT_BASE 0xFFFC0000
+
+#define CONFIG_SYS_CLK_FREQ 33333333 /* external frequency to pll */
+
+#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
+
+#define PLLMR0_DEFAULT PLLMR0_266_133_66 /* no PCI */
+#define PLLMR1_DEFAULT PLLMR1_266_133_66 /* no PCI */
+
+/* the environment is in the EEPROM by default */
+#define CONFIG_ENV_IS_IN_EEPROM
+#undef CONFIG_ENV_IS_IN_FLASH
+
+#define CONFIG_PPC4xx_EMAC
+#define CONFIG_HAS_ETH1 1
+#define CONFIG_MII 1 /* MII PHY management */
+#define CONFIG_PHY_ADDR 0x01 /* PHY address */
+#define CONFIG_SYS_RX_ETH_BUFFER 16 /* Number of ethernet rx buffers & descriptors */
+#define CONFIG_PHY_RESET 1
+#define CONFIG_PHY_RESET_DELAY 300 /* PHY RESET recovery delay */
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#undef CONFIG_CMD_ASKENV
+#undef CONFIG_CMD_CACHE
+#define CONFIG_CMD_DHCP
+#undef CONFIG_CMD_DIAG
+#define CONFIG_CMD_EEPROM
+#undef CONFIG_CMD_ELF
+#define CONFIG_CMD_I2C
+#undef CONFIG_CMD_IRQ
+#define CONFIG_CMD_JFFS2
+#undef CONFIG_CMD_MII
+#define CONFIG_CMD_NAND
+#undef CONFIG_CMD_PING
+#define CONFIG_CMD_REGINFO
+
+#undef CONFIG_WATCHDOG /* watchdog disabled */
+
+/*-----------------------------------------------------------------------
+ * SDRAM
+ *----------------------------------------------------------------------*/
+/*
+ * SDRAM configuration (please see cpu/ppc/sdram.[ch])
+ */
+#define CONFIG_SDRAM_BANK0 1
+
+/* FIX! SDRAM timings used in datasheet */
+#define CONFIG_SYS_SDRAM_CL 3 /* CAS latency */
+#define CONFIG_SYS_SDRAM_tRP 20 /* PRECHARGE command period */
+#define CONFIG_SYS_SDRAM_tRC 66 /* ACTIVE-to-ACTIVE command period */
+#define CONFIG_SYS_SDRAM_tRCD 20 /* ACTIVE-to-READ delay */
+#define CONFIG_SYS_SDRAM_tRFC 66 /* Auto refresh period */
+
+/*
+ * JFFS2
+ */
+#define CONFIG_SYS_JFFS2_FIRST_BANK 0
+#ifdef CONFIG_SYS_KERNEL_IN_JFFS2
+#define CONFIG_SYS_JFFS2_FIRST_SECTOR 0 /* JFFS starts at block 0 */
+#else /* kernel not in JFFS */
+#define CONFIG_SYS_JFFS2_FIRST_SECTOR 8 /* block 0-7 is kernel (1MB = 8 sectors) */
+#endif
+#define CONFIG_SYS_JFFS2_NUM_BANKS 1
+
+/*-----------------------------------------------------------------------
+ * Serial Port
+ *----------------------------------------------------------------------*/
+#define CONFIG_CONS_INDEX 1 /* Use UART0 */
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE 1
+#define CONFIG_SYS_NS16550_CLK get_serial_clock()
+#undef CONFIG_SYS_EXT_SERIAL_CLOCK /* external serial clock */
+#define CONFIG_SYS_BASE_BAUD 691200
+#define CONFIG_BAUDRATE 115200
+
+/* The following table includes the supported baudrates */
+#define CONFIG_SYS_BAUDRATE_TABLE \
+ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400}
+
+/*-----------------------------------------------------------------------
+ * Miscellaneous configurable options
+ *----------------------------------------------------------------------*/
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#if defined(CONFIG_CMD_KGDB)
+#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
+#else
+#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
+#endif
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
+
+#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */
+#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
+
+#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
+#define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_info (bd_t) */
+
+#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
+#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
+
+#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
+#define CONFIG_LOOPW 1 /* enable loopw command */
+#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */
+#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
+#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
+
+/*-----------------------------------------------------------------------
+ * I2C
+ *----------------------------------------------------------------------*/
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_PPC4XX
+#define CONFIG_SYS_I2C_PPC4XX_CH0
+#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000
+#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F
+
+#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* base address */
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 /* bytes of address */
+
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5 /* 8 byte write page size */
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */
+#define CONFIG_SYS_EEPROM_SIZE 0x2000
+
+/*-----------------------------------------------------------------------
+ * Start addresses for the final memory configuration
+ * (Set up by the startup code)
+ * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
+ */
+#define CONFIG_SYS_SDRAM_BASE 0x00000000
+#define CONFIG_SYS_FLASH_BASE 0xFFC00000
+#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Monitor */
+#define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc() */
+#define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_TEXT_BASE)
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+
+/*-----------------------------------------------------------------------
+ * FLASH organization
+ */
+#define CONFIG_SYS_FLASH_CFI /* The flash is CFI compatible */
+#define CONFIG_FLASH_CFI_DRIVER
+
+#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE }
+
+#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
+#define CONFIG_SYS_MAX_FLASH_SECT 128 /* max number of sectors on one chip */
+
+#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
+
+#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */
+#define CONFIG_SYS_FLASH_INCREMENT 0 /* there is only one bank */
+
+#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
+#define CONFIG_SYS_FLASH_QUIET_TEST 1 /* don't warn upon unknown flash */
+
+#ifdef CONFIG_ENV_IS_IN_FLASH
+#define CONFIG_ENV_SECT_SIZE 0x10000 /* size of one complete sector */
+/* the environment is located before u-boot */
+#define CONFIG_ENV_ADDR (CONFIG_SYS_TEXT_BASE - CONFIG_ENV_SECT_SIZE)
+
+/* Address and size of Redundant Environment Sector */
+#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR - CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SECT_SIZE)
+#endif
+
+#ifdef CONFIG_ENV_IS_IN_EEPROM
+#define CONFIG_ENV_SIZE 0x400 /* Size of Environment vars */
+#define CONFIG_ENV_OFFSET 0x00000000
+#define CONFIG_SYS_ENABLE_CRC_16 1 /* Intrinsyc formatting used crc16 */
+#endif
+
+/* partly from PPCBoot */
+/* NAND */
+#define CONFIG_NAND
+#ifdef CONFIG_NAND
+#define CONFIG_SYS_NAND_BASE 0x60000000
+#define CONFIG_SYS_NAND_CS 10 /* our CS is GPIO10 */
+#define CONFIG_SYS_NAND_RDY 23 /* our RDY is GPIO23 */
+#define CONFIG_SYS_NAND_CE 24 /* our CE is GPIO24 */
+#define CONFIG_SYS_NAND_CLE 31 /* our CLE is GPIO31 */
+#define CONFIG_SYS_NAND_ALE 30 /* our ALE is GPIO30 */
+#define CONFIG_SYS_MAX_NAND_DEVICE 1
+
+#endif
+
+/*-----------------------------------------------------------------------
+ * Definitions for initial stack pointer and data area (in data cache)
+ */
+/* use on chip memory (OCM) for temperary stack until sdram is tested */
+/* see ./arch/powerpc/cpu/ppc4xx/start.S */
+#define CONFIG_SYS_TEMP_STACK_OCM 1
+
+/* On Chip Memory location */
+#define CONFIG_SYS_OCM_DATA_ADDR 0xF8000000
+#define CONFIG_SYS_OCM_DATA_SIZE 0x1000
+#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_DATA_ADDR /* inside of OCM */
+#define CONFIG_SYS_INIT_RAM_SIZE CONFIG_SYS_OCM_DATA_SIZE /* Size of used area in RAM */
+
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
+
+/*-----------------------------------------------------------------------
+ * External Bus Controller (EBC) Setup
+ * Taken from PPCBoot board/icecube/icecube.h
+ */
+
+/* see ./arch/powerpc/cpu/ppc4xx/cpu_init.c ./cpu/ppc4xx/ndfc.c */
+#define CONFIG_SYS_EBC_PB0AP 0x04002480
+/* AMD NOR flash - this corresponds to FLASH_BASE so may be correct */
+#define CONFIG_SYS_EBC_PB0CR 0xFFC5A000
+#define CONFIG_SYS_EBC_PB1AP 0x04005480
+#define CONFIG_SYS_EBC_PB1CR 0x60018000
+#define CONFIG_SYS_EBC_PB2AP 0x00000000
+#define CONFIG_SYS_EBC_PB2CR 0x00000000
+#define CONFIG_SYS_EBC_PB3AP 0x00000000
+#define CONFIG_SYS_EBC_PB3CR 0x00000000
+#define CONFIG_SYS_EBC_PB4AP 0x00000000
+#define CONFIG_SYS_EBC_PB4CR 0x00000000
+
+/*-----------------------------------------------------------------------
+ * Definitions for GPIO setup (PPC405EP specific)
+ *
+ * Taken in part from PPCBoot board/icecube/icecube.h
+ */
+/* see ./arch/powerpc/cpu/ppc4xx/cpu_init.c ./cpu/ppc4xx/start.S */
+#define CONFIG_SYS_GPIO0_OSRL 0x55555550
+#define CONFIG_SYS_GPIO0_OSRH 0x00000110
+#define CONFIG_SYS_GPIO0_ISR1L 0x00000000
+#define CONFIG_SYS_GPIO0_ISR1H 0x15555445
+#define CONFIG_SYS_GPIO0_TSRL 0x00000000
+#define CONFIG_SYS_GPIO0_TSRH 0x00000000
+#define CONFIG_SYS_GPIO0_TCR 0xFFFF8097
+#define CONFIG_SYS_GPIO0_ODR 0x00000000
+
+#if defined(CONFIG_CMD_KGDB)
+#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
+#endif
+
+/* ENVIRONMENT VARS */
+
+#define CONFIG_IPADDR 192.168.1.67
+#define CONFIG_SERVERIP 192.168.1.50
+#define CONFIG_GATEWAYIP 192.168.1.1
+#define CONFIG_NETMASK 255.255.255.0
+#define CONFIG_LOADADDR 300000
+#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
+
+/* pass open firmware flat tree */
+#define CONFIG_OF_LIBFDT 1
+
+#endif /* __CONFIG_H */
Code Review / kvmfornfv.git / blobdiff