--- /dev/null
+/*
+ * Copyright (C) 2009, Ilya Yanok, Emcraft Systems, <yanok@emcraft.com>
+ *
+ * Configuration settings for the Dave/DENX QongEVB-LITE board.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#include <asm/arch/imx-regs.h>
+
+/* High Level Configuration Options */
+#define CONFIG_ARM1136 /* This is an arm1136 CPU core */
+#define CONFIG_MX31 /* in a mx31 */
+#define CONFIG_QONG
+
+#define CONFIG_DISPLAY_CPUINFO
+#define CONFIG_DISPLAY_BOARDINFO
+
+#define CONFIG_SYS_TEXT_BASE 0xa0000000
+
+#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */
+#define CONFIG_SETUP_MEMORY_TAGS
+#define CONFIG_INITRD_TAG
+
+/*
+ * Size of malloc() pool
+ */
+#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 1536 * 1024)
+
+/*
+ * Hardware drivers
+ */
+
+#define CONFIG_MXC_UART
+#define CONFIG_MXC_UART_BASE UART1_BASE
+
+#define CONFIG_MXC_GPIO
+#define CONFIG_HW_WATCHDOG
+#define CONFIG_IMX_WATCHDOG
+
+#define CONFIG_MXC_SPI
+#define CONFIG_DEFAULT_SPI_BUS 1
+#define CONFIG_DEFAULT_SPI_MODE (SPI_MODE_0 | SPI_CS_HIGH)
+#define CONFIG_RTC_MC13XXX
+
+#define CONFIG_POWER
+#define CONFIG_POWER_SPI
+#define CONFIG_POWER_FSL
+#define CONFIG_FSL_PMIC_BUS 1
+#define CONFIG_FSL_PMIC_CS 0
+#define CONFIG_FSL_PMIC_CLK 100000
+#define CONFIG_FSL_PMIC_MODE (SPI_MODE_0 | SPI_CS_HIGH)
+#define CONFIG_FSL_PMIC_BITLEN 32
+
+/* FPGA */
+#define CONFIG_FPGA
+#define CONFIG_QONG_FPGA
+#define CONFIG_FPGA_BASE (CS1_BASE)
+#define CONFIG_FPGA_LATTICE
+#define CONFIG_FPGA_COUNT 1
+
+#ifdef CONFIG_QONG_FPGA
+/* Ethernet */
+#define CONFIG_DNET
+#define CONFIG_DNET_BASE (CS1_BASE + QONG_FPGA_PERIPH_SIZE)
+
+/* Framebuffer and LCD */
+#define CONFIG_VIDEO
+#define CONFIG_CFB_CONSOLE
+#define CONFIG_VIDEO_MX3
+#define CONFIG_VIDEO_LOGO
+#define CONFIG_VIDEO_SW_CURSOR
+#define CONFIG_VGA_AS_SINGLE_DEVICE
+#define CONFIG_SYS_CONSOLE_IS_IN_ENV
+#define CONFIG_SPLASH_SCREEN
+#define CONFIG_CMD_BMP
+#define CONFIG_BMP_16BPP
+#define CONFIG_VIDEO_BMP_GZIP
+#define CONFIG_SYS_VIDEO_LOGO_MAX_SIZE (512 << 10)
+
+/* USB */
+#define CONFIG_CMD_USB
+#ifdef CONFIG_CMD_USB
+#define CONFIG_USB_EHCI /* Enable EHCI USB support */
+#define CONFIG_USB_EHCI_MXC
+#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
+#define CONFIG_MXC_USB_PORT 2
+#define CONFIG_MXC_USB_PORTSC (MXC_EHCI_MODE_ULPI | MXC_EHCI_UTMI_8BIT)
+#define CONFIG_MXC_USB_FLAGS MXC_EHCI_POWER_PINS_ENABLED
+#define CONFIG_EHCI_IS_TDI
+#define CONFIG_USB_STORAGE
+#define CONFIG_DOS_PARTITION
+#define CONFIG_SUPPORT_VFAT
+#define CONFIG_CMD_EXT2
+#define CONFIG_CMD_FAT
+#endif /* CONFIG_CMD_USB */
+
+/*
+ * Reducing the ARP timeout from default 5 seconds to 200ms we speed up the
+ * initial TFTP transfer, should the user wish one, significantly.
+ */
+#define CONFIG_ARP_TIMEOUT 200UL
+
+#endif /* CONFIG_QONG_FPGA */
+
+#define CONFIG_CONS_INDEX 1
+#define CONFIG_BAUDRATE 115200
+
+/***********************************************************
+ * Command definition
+ ***********************************************************/
+
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_CACHE
+#define CONFIG_CMD_DATE
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_NAND
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_SETEXPR
+#define CONFIG_CMD_SPI
+#define CONFIG_CMD_UNZIP
+
+#define CONFIG_BOARD_LATE_INIT
+
+#define CONFIG_BOOTDELAY 5
+
+#define CONFIG_LOADADDR 0x80800000 /* loadaddr env var */
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "netdev=eth0\0" \
+ "nfsargs=setenv bootargs root=/dev/nfs rw " \
+ "nfsroot=${serverip}:${rootpath}\0" \
+ "ramargs=setenv bootargs root=/dev/ram rw\0" \
+ "addip=setenv bootargs ${bootargs} " \
+ "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
+ ":${hostname}:${netdev}:off panic=1\0" \
+ "addtty=setenv bootargs ${bootargs}" \
+ " console=ttymxc0,${baudrate}\0" \
+ "addmtd=setenv bootargs ${bootargs} ${mtdparts}\0" \
+ "addmisc=setenv bootargs ${bootargs}\0" \
+ "uboot_addr=A0000000\0" \
+ "kernel_addr=A00C0000\0" \
+ "ramdisk_addr=A0300000\0" \
+ "u-boot=qong/u-boot.bin\0" \
+ "kernel_addr_r=80800000\0" \
+ "hostname=qong\0" \
+ "bootfile=qong/uImage\0" \
+ "rootpath=/opt/eldk-4.2-arm/armVFP\0" \
+ "flash_self=run ramargs addip addtty addmtd addmisc;" \
+ "bootm ${kernel_addr} ${ramdisk_addr}\0" \
+ "flash_nfs=run nfsargs addip addtty addmtd addmisc;" \
+ "bootm ${kernel_addr}\0" \
+ "net_nfs=tftp ${kernel_addr_r} ${bootfile};" \
+ "run nfsargs addip addtty addmtd addmisc;" \
+ "bootm\0" \
+ "bootcmd=run flash_self\0" \
+ "load=tftp ${loadaddr} ${u-boot}\0" \
+ "update=protect off " __stringify(CONFIG_SYS_MONITOR_BASE) \
+ " +${filesize};era " __stringify(CONFIG_SYS_MONITOR_BASE)\
+ " +${filesize};cp.b ${fileaddr} " \
+ __stringify(CONFIG_SYS_MONITOR_BASE) " ${filesize}\0" \
+ "upd=run load update\0" \
+ "videomode=video=ctfb:x:640,y:480,depth:16,mode:0,pclk:40000," \
+ "le:120,ri:40,up:35,lo:10,hs:30,vs:3,sync:100663296," \
+ "vmode:0\0" \
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */
+/* Print Buffer Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
+ sizeof(CONFIG_SYS_PROMPT) + 16)
+#define CONFIG_SYS_MAXARGS 32 /* max number of command args */
+/* Boot Argument Buffer Size */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
+
+/* memtest works on first 255MB of RAM */
+#define CONFIG_SYS_MEMTEST_START PHYS_SDRAM_1
+#define CONFIG_SYS_MEMTEST_END (PHYS_SDRAM_1 + 0xff000000)
+
+#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
+
+#define CONFIG_CMDLINE_EDITING
+#define CONFIG_SYS_HUSH_PARSER /* Use the HUSH parser */
+
+#define CONFIG_MISC_INIT_R
+
+/*-----------------------------------------------------------------------
+ * Physical Memory Map
+ */
+#define CONFIG_NR_DRAM_BANKS 1
+#define PHYS_SDRAM_1 CSD0_BASE
+#define PHYS_SDRAM_1_SIZE 0x10000000 /* 256 MB */
+
+/*
+ * NAND driver
+ */
+
+#ifndef __ASSEMBLY__
+extern void qong_nand_plat_init(void *chip);
+extern int qong_nand_rdy(void *chip);
+#endif
+#define CONFIG_NAND_PLAT
+#define CONFIG_SYS_MAX_NAND_DEVICE 1
+#define CONFIG_SYS_NAND_BASE CS3_BASE
+#define NAND_PLAT_INIT() qong_nand_plat_init(nand)
+
+#define QONG_NAND_CLE(chip) ((unsigned long)(chip)->IO_ADDR_W | (1 << 24))
+#define QONG_NAND_ALE(chip) ((unsigned long)(chip)->IO_ADDR_W | (1 << 23))
+#define QONG_NAND_WRITE(addr, cmd) \
+ do { \
+ __REG8(addr) = cmd; \
+ } while (0)
+
+#define NAND_PLAT_WRITE_CMD(chip, cmd) QONG_NAND_WRITE(QONG_NAND_CLE(chip), cmd)
+#define NAND_PLAT_WRITE_ADR(chip, cmd) QONG_NAND_WRITE(QONG_NAND_ALE(chip), cmd)
+#define NAND_PLAT_DEV_READY(chip) (qong_nand_rdy(chip))
+
+/*-----------------------------------------------------------------------
+ * FLASH and environment organization
+ */
+#define CONFIG_SYS_FLASH_BASE CS0_BASE
+#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
+/* max number of sectors on one chip */
+#define CONFIG_SYS_MAX_FLASH_SECT 1024
+/* Monitor at beginning of flash */
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
+#define CONFIG_SYS_MONITOR_LEN 0x40000 /* Reserve 256KiB */
+
+#define CONFIG_ENV_IS_IN_FLASH
+#define CONFIG_ENV_SECT_SIZE 0x20000
+#define CONFIG_ENV_SIZE CONFIG_ENV_SECT_SIZE
+#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x80000)
+
+/* Address and size of Redundant Environment Sector */
+#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)
+#define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE
+
+/*-----------------------------------------------------------------------
+ * CFI FLASH driver setup
+ */
+/* Flash memory is CFI compliant */
+#define CONFIG_SYS_FLASH_CFI
+/* Use drivers/cfi_flash.c */
+#define CONFIG_FLASH_CFI_DRIVER
+/* Use buffered writes (~10x faster) */
+#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
+/* Use hardware sector protection */
+#define CONFIG_SYS_FLASH_PROTECTION
+
+/*
+ * Filesystem
+ */
+#define CONFIG_CMD_JFFS2
+#define CONFIG_CMD_UBI
+#define CONFIG_CMD_UBIFS
+#define CONFIG_RBTREE
+#define CONFIG_MTD_PARTITIONS
+#define CONFIG_CMD_MTDPARTS
+#define CONFIG_LZO
+#define CONFIG_MTD_DEVICE /* needed for mtdparts commands */
+#define CONFIG_FLASH_CFI_MTD
+#define MTDIDS_DEFAULT "nor0=physmap-flash.0," \
+ "nand0=gen_nand"
+#define MTDPARTS_DEFAULT \
+ "mtdparts=physmap-flash.0:" \
+ "512k(U-Boot),128k(env1),128k(env2)," \
+ "2304k(kernel),13m(ramdisk),-(user);" \
+ "gen_nand:" \
+ "128m(nand)"
+
+/* additions for new relocation code, must be added to all boards */
+#define CONFIG_SYS_SDRAM_BASE 0x80000000
+#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR
+#define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_GBL_DATA_OFFSET)
+
+#define CONFIG_BOARD_EARLY_INIT_F
+
+#endif /* __CONFIG_H */
Code Review / kvmfornfv.git / blobdiff