--- /dev/null
+/*
+ * (C) Copyright 2010
+ * Ilko Iliev <iliev@ronetix.at>
+ * Asen Dimov <dimov@ronetix.at>
+ * Ronetix GmbH <www.ronetix.at>
+ *
+ * (C) Copyright 2007-2008
+ * Stelian Pop <stelian@popies.net>
+ * Lead Tech Design <www.leadtechdesign.com>
+ *
+ * Configuation settings for the PM9G45 board.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * SoC must be defined first, before hardware.h is included.
+ * In this case SoC is defined in boards.cfg.
+ */
+#include <asm/hardware.h>
+
+#define CONFIG_PM9G45 1 /* It's an Ronetix PM9G45 */
+#define CONFIG_SYS_AT91_CPU_NAME "AT91SAM9G45"
+
+#define MACH_TYPE_PM9G45 2672
+#define CONFIG_MACH_TYPE MACH_TYPE_PM9G45
+
+/* ARM asynchronous clock */
+#define CONFIG_SYS_AT91_MAIN_CLOCK 12000000 /* from 12 MHz crystal */
+#define CONFIG_SYS_AT91_SLOW_CLOCK 32768 /* slow clock xtal */
+#define CONFIG_SYS_TEXT_BASE 0x73f00000
+
+#define CONFIG_ARCH_CPU_INIT
+
+#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */
+#define CONFIG_SETUP_MEMORY_TAGS 1
+#define CONFIG_INITRD_TAG 1
+
+#define CONFIG_SKIP_LOWLEVEL_INIT
+#define CONFIG_BOARD_EARLY_INIT_F
+
+/*
+ * Hardware drivers
+ */
+#define CONFIG_AT91_GPIO 1
+#define CONFIG_ATMEL_USART 1
+#define CONFIG_USART_BASE ATMEL_BASE_DBGU
+#define CONFIG_USART_ID ATMEL_ID_SYS
+
+#define CONFIG_SYS_USE_NANDFLASH 1
+
+/* LED */
+#define CONFIG_AT91_LED
+#define CONFIG_RED_LED GPIO_PIN_PD(31) /* this is the user1 led */
+#define CONFIG_GREEN_LED GPIO_PIN_PD(0) /* this is the user2 led */
+
+#define CONFIG_BOOTDELAY 3
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE 1
+#define CONFIG_BOOTP_BOOTPATH 1
+#define CONFIG_BOOTP_GATEWAY 1
+#define CONFIG_BOOTP_HOSTNAME 1
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+#undef CONFIG_CMD_FPGA
+#undef CONFIG_CMD_IMLS
+
+#define CONFIG_CMD_CACHE
+#define CONFIG_CMD_PING 1
+#define CONFIG_CMD_DHCP 1
+#define CONFIG_CMD_NAND 1
+#define CONFIG_CMD_USB 1
+
+#define CONFIG_CMD_JFFS2 1
+#define CONFIG_JFFS2_CMDLINE 1
+#define CONFIG_JFFS2_NAND 1
+#define CONFIG_JFFS2_DEV "nand0" /* NAND dev jffs2 lives on */
+#define CONFIG_JFFS2_PART_OFFSET 0 /* start of jffs2 partition */
+#define CONFIG_JFFS2_PART_SIZE (256 * 1024 * 1024) /* partition */
+
+/* SDRAM */
+#define CONFIG_NR_DRAM_BANKS 1
+#define PHYS_SDRAM 0x70000000
+#define PHYS_SDRAM_SIZE 0x08000000 /* 128 megs */
+
+/* NOR flash, not available */
+#define CONFIG_SYS_NO_FLASH 1
+#undef CONFIG_CMD_FLASH
+
+/* NAND flash */
+#ifdef CONFIG_CMD_NAND
+#define CONFIG_NAND_ATMEL
+#define CONFIG_SYS_MAX_NAND_DEVICE 1
+#define CONFIG_SYS_NAND_BASE 0x40000000
+#define CONFIG_SYS_NAND_DBW_8 1
+/* our ALE is AD21 */
+#define CONFIG_SYS_NAND_MASK_ALE (1 << 21)
+/* our CLE is AD22 */
+#define CONFIG_SYS_NAND_MASK_CLE (1 << 22)
+#define CONFIG_SYS_NAND_ENABLE_PIN GPIO_PIN_PC(14)
+#define CONFIG_SYS_NAND_READY_PIN GPIO_PIN_PD(3)
+
+#endif
+
+/* Ethernet */
+#define CONFIG_MACB 1
+#define CONFIG_RMII 1
+#define CONFIG_NET_RETRY_COUNT 20
+#define CONFIG_RESET_PHY_R 1
+
+/* USB */
+#define CONFIG_USB_ATMEL
+#define CONFIG_USB_ATMEL_CLK_SEL_UPLL
+#define CONFIG_USB_OHCI_NEW 1
+#define CONFIG_DOS_PARTITION 1
+#define CONFIG_SYS_USB_OHCI_CPU_INIT 1
+#define CONFIG_SYS_USB_OHCI_REGS_BASE 0x00700000 /* _UHP_OHCI_BASE */
+#define CONFIG_SYS_USB_OHCI_SLOT_NAME "at91sam9g45"
+#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 2
+#define CONFIG_USB_STORAGE 1
+
+/* board specific(not enough SRAM) */
+#define CONFIG_AT91SAM9G45_LCD_BASE PHYS_SDRAM + 0xE00000
+
+#define CONFIG_SYS_LOAD_ADDR PHYS_SDRAM + 0x2000000 /* load addr */
+
+#define CONFIG_SYS_MEMTEST_START PHYS_SDRAM
+#define CONFIG_SYS_MEMTEST_END CONFIG_AT91SAM9G45_LCD_BASE
+
+/* bootstrap + u-boot + env + linux in nandflash */
+#define CONFIG_ENV_IS_IN_NAND 1
+#define CONFIG_ENV_OFFSET 0x60000
+#define CONFIG_ENV_OFFSET_REDUND 0x80000
+#define CONFIG_ENV_SIZE 0x20000 /* 1 sector = 128 kB */
+#define CONFIG_BOOTCOMMAND "nand read 0x72000000 0x200000 0x200000; bootm"
+#define CONFIG_BOOTARGS "fbcon=rotate:3 console=tty0 " \
+ "console=ttyS0,115200 " \
+ "root=/dev/mtdblock4 " \
+ "mtdparts=atmel_nand:128k(bootstrap)ro," \
+ "256k(uboot)ro,1664k(env)," \
+ "2M(linux)ro,-(root) rw " \
+ "rootfstype=jffs2"
+
+#define CONFIG_BAUDRATE 115200
+
+#define CONFIG_SYS_PROMPT "U-Boot> "
+#define CONFIG_SYS_CBSIZE 256
+#define CONFIG_SYS_MAXARGS 16
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
+ sizeof(CONFIG_SYS_PROMPT) + 16)
+#define CONFIG_SYS_LONGHELP 1
+#define CONFIG_CMDLINE_EDITING 1
+#define CONFIG_AUTO_COMPLETE
+#define CONFIG_SYS_HUSH_PARSER
+
+/*
+ * Size of malloc() pool
+ */
+#define CONFIG_SYS_MALLOC_LEN ROUND(3 * CONFIG_ENV_SIZE + 128*1024,\
+ 0x1000)
+
+#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM
+#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_SDRAM_BASE + 0x1000 - \
+ GENERATED_GBL_DATA_SIZE)
+
+#endif
Code Review / kvmfornfv.git / blobdiff