--- /dev/null
+/*
+ * (C) Copyright 2007-2008
+ * Stelian Pop <stelian@popies.net>
+ * Lead Tech Design <www.leadtechdesign.com>
+ * Ilko Iliev <www.ronetix.at>
+ *
+ * Configuation settings for the RONETIX PM9263 board.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * SoC must be defined first, before hardware.h is included.
+ * In this case SoC is defined in boards.cfg.
+ */
+#include <asm/hardware.h>
+
+/* ARM asynchronous clock */
+#define CONFIG_DISPLAY_CPUINFO
+#define CONFIG_DISPLAY_BOARDINFO
+
+#define MASTER_PLL_DIV 6
+#define MASTER_PLL_MUL 65
+#define MAIN_PLL_DIV 2 /* 2 or 4 */
+#define CONFIG_SYS_AT91_MAIN_CLOCK 18432000
+#define CONFIG_SYS_AT91_SLOW_CLOCK 32768 /* slow clock xtal */
+
+#define CONFIG_SYS_AT91_CPU_NAME "AT91SAM9263"
+#define CONFIG_PM9263 1 /* on a Ronetix PM9263 Board */
+#define CONFIG_ARCH_CPU_INIT
+#define CONFIG_SYS_TEXT_BASE 0
+
+#define MACH_TYPE_PM9263 1475
+#define CONFIG_MACH_TYPE MACH_TYPE_PM9263
+
+/* clocks */
+#define CONFIG_SYS_MOR_VAL \
+ (AT91_PMC_MOR_MOSCEN | \
+ (255 << 8)) /* Main Oscillator Start-up Time */
+#define CONFIG_SYS_PLLAR_VAL \
+ (AT91_PMC_PLLAR_29 | /* Bit 29 must be 1 when prog */ \
+ AT91_PMC_PLLXR_OUT(3) | \
+ AT91_PMC_PLLXR_PLLCOUNT(0x3f) | /* PLL Counter */\
+ (2 << 28) | /* PLL Clock Frequency Range */ \
+ ((MASTER_PLL_MUL - 1) << 16) | (MASTER_PLL_DIV))
+
+#if (MAIN_PLL_DIV == 2)
+/* PCK/2 = MCK Master Clock from PLLA */
+#define CONFIG_SYS_MCKR1_VAL \
+ (AT91_PMC_MCKR_CSS_SLOW | \
+ AT91_PMC_MCKR_PRES_1 | \
+ AT91_PMC_MCKR_MDIV_2)
+/* PCK/2 = MCK Master Clock from PLLA */
+#define CONFIG_SYS_MCKR2_VAL \
+ (AT91_PMC_MCKR_CSS_PLLA | \
+ AT91_PMC_MCKR_PRES_1 | \
+ AT91_PMC_MCKR_MDIV_2)
+#else
+/* PCK/4 = MCK Master Clock from PLLA */
+#define CONFIG_SYS_MCKR1_VAL \
+ (AT91_PMC_MCKR_CSS_SLOW | \
+ AT91_PMC_MCKR_PRES_1 | \
+ AT91_PMC_MCKR_MDIV_4)
+/* PCK/4 = MCK Master Clock from PLLA */
+#define CONFIG_SYS_MCKR2_VAL \
+ (AT91_PMC_MCKR_CSS_PLLA | \
+ AT91_PMC_MCKR_PRES_1 | \
+ AT91_PMC_MCKR_MDIV_4)
+#endif
+/* define PDC[31:16] as DATA[31:16] */
+#define CONFIG_SYS_PIOD_PDR_VAL1 0xFFFF0000
+/* no pull-up for D[31:16] */
+#define CONFIG_SYS_PIOD_PPUDR_VAL 0xFFFF0000
+/* EBI0_CSA, CS1 SDRAM, CS3 NAND Flash, 3.3V memories */
+#define CONFIG_SYS_MATRIX_EBI0CSA_VAL \
+ (AT91_MATRIX_CSA_DBPUC | AT91_MATRIX_CSA_VDDIOMSEL_3_3V | \
+ AT91_MATRIX_CSA_EBI_CS1A)
+
+/* SDRAM */
+/* SDRAMC_MR Mode register */
+#define CONFIG_SYS_SDRC_MR_VAL1 0
+/* SDRAMC_TR - Refresh Timer register */
+#define CONFIG_SYS_SDRC_TR_VAL1 0x3AA
+/* SDRAMC_CR - Configuration register*/
+#define CONFIG_SYS_SDRC_CR_VAL \
+ (AT91_SDRAMC_NC_9 | \
+ AT91_SDRAMC_NR_13 | \
+ AT91_SDRAMC_NB_4 | \
+ AT91_SDRAMC_CAS_2 | \
+ AT91_SDRAMC_DBW_32 | \
+ (2 << 8) | /* tWR - Write Recovery Delay */ \
+ (7 << 12) | /* tRC - Row Cycle Delay */ \
+ (2 << 16) | /* tRP - Row Precharge Delay */ \
+ (2 << 20) | /* tRCD - Row to Column Delay */ \
+ (5 << 24) | /* tRAS - Active to Precharge Delay */ \
+ (8 << 28)) /* tXSR - Exit Self Refresh to Active Delay */
+
+/* Memory Device Register -> SDRAM */
+#define CONFIG_SYS_SDRC_MDR_VAL AT91_SDRAMC_MD_SDRAM
+#define CONFIG_SYS_SDRC_MR_VAL2 AT91_SDRAMC_MODE_PRECHARGE
+#define CONFIG_SYS_SDRAM_VAL1 0 /* SDRAM_BASE */
+#define CONFIG_SYS_SDRC_MR_VAL3 AT91_SDRAMC_MODE_REFRESH
+#define CONFIG_SYS_SDRAM_VAL2 0 /* SDRAM_BASE */
+#define CONFIG_SYS_SDRAM_VAL3 0 /* SDRAM_BASE */
+#define CONFIG_SYS_SDRAM_VAL4 0 /* SDRAM_BASE */
+#define CONFIG_SYS_SDRAM_VAL5 0 /* SDRAM_BASE */
+#define CONFIG_SYS_SDRAM_VAL6 0 /* SDRAM_BASE */
+#define CONFIG_SYS_SDRAM_VAL7 0 /* SDRAM_BASE */
+#define CONFIG_SYS_SDRAM_VAL8 0 /* SDRAM_BASE */
+#define CONFIG_SYS_SDRAM_VAL9 0 /* SDRAM_BASE */
+#define CONFIG_SYS_SDRC_MR_VAL4 AT91_SDRAMC_MODE_LMR
+#define CONFIG_SYS_SDRAM_VAL10 0 /* SDRAM_BASE */
+#define CONFIG_SYS_SDRC_MR_VAL5 AT91_SDRAMC_MODE_NORMAL
+#define CONFIG_SYS_SDRAM_VAL11 0 /* SDRAM_BASE */
+#define CONFIG_SYS_SDRC_TR_VAL2 1200 /* SDRAM_TR */
+#define CONFIG_SYS_SDRAM_VAL12 0 /* SDRAM_BASE */
+
+/* setup SMC0, CS0 (NOR Flash) - 16-bit, 15 WS */
+#define CONFIG_SYS_SMC0_SETUP0_VAL \
+ (AT91_SMC_SETUP_NWE(10) | AT91_SMC_SETUP_NCS_WR(10) | \
+ AT91_SMC_SETUP_NRD(10) | AT91_SMC_SETUP_NCS_RD(10))
+#define CONFIG_SYS_SMC0_PULSE0_VAL \
+ (AT91_SMC_PULSE_NWE(11) | AT91_SMC_PULSE_NCS_WR(11) | \
+ AT91_SMC_PULSE_NRD(11) | AT91_SMC_PULSE_NCS_RD(11))
+#define CONFIG_SYS_SMC0_CYCLE0_VAL \
+ (AT91_SMC_CYCLE_NWE(22) | AT91_SMC_CYCLE_NRD(22))
+#define CONFIG_SYS_SMC0_MODE0_VAL \
+ (AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE | \
+ AT91_SMC_MODE_DBW_16 | \
+ AT91_SMC_MODE_TDF | \
+ AT91_SMC_MODE_TDF_CYCLE(6))
+
+/* user reset enable */
+#define CONFIG_SYS_RSTC_RMR_VAL \
+ (AT91_RSTC_KEY | \
+ AT91_RSTC_CR_PROCRST | \
+ AT91_RSTC_MR_ERSTL(1) | \
+ AT91_RSTC_MR_ERSTL(2))
+
+/* Disable Watchdog */
+#define CONFIG_SYS_WDTC_WDMR_VAL \
+ (AT91_WDT_MR_WDIDLEHLT | AT91_WDT_MR_WDDBGHLT | \
+ AT91_WDT_MR_WDV(0xfff) | \
+ AT91_WDT_MR_WDDIS | \
+ AT91_WDT_MR_WDD(0xfff))
+
+#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */
+#define CONFIG_SETUP_MEMORY_TAGS 1
+#define CONFIG_INITRD_TAG 1
+
+#undef CONFIG_SKIP_LOWLEVEL_INIT
+#define CONFIG_USER_LOWLEVEL_INIT 1
+#define CONFIG_BOARD_EARLY_INIT_F
+
+/*
+ * Hardware drivers
+ */
+#define CONFIG_AT91_GPIO 1
+#define CONFIG_ATMEL_USART 1
+#define CONFIG_USART_BASE ATMEL_BASE_DBGU
+#define CONFIG_USART_ID ATMEL_ID_SYS
+
+/* LCD */
+#define CONFIG_LCD 1
+#define LCD_BPP LCD_COLOR8
+#define CONFIG_LCD_LOGO 1
+#undef LCD_TEST_PATTERN
+#define CONFIG_LCD_INFO 1
+#define CONFIG_LCD_INFO_BELOW_LOGO 1
+#define CONFIG_SYS_WHITE_ON_BLACK 1
+#define CONFIG_ATMEL_LCD 1
+#define CONFIG_ATMEL_LCD_BGR555 1
+#define CONFIG_SYS_CONSOLE_IS_IN_ENV 1
+
+#define CONFIG_LCD_IN_PSRAM 1
+
+/* LED */
+#define CONFIG_AT91_LED
+#define CONFIG_RED_LED GPIO_PIN_PB(7) /* this is the power led */
+#define CONFIG_GREEN_LED GPIO_PIN_PB(8) /* this is the user1 led */
+
+#define CONFIG_BOOTDELAY 3
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE 1
+#define CONFIG_BOOTP_BOOTPATH 1
+#define CONFIG_BOOTP_GATEWAY 1
+#define CONFIG_BOOTP_HOSTNAME 1
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+#undef CONFIG_CMD_BDI
+#undef CONFIG_CMD_IMI
+#undef CONFIG_CMD_FPGA
+#undef CONFIG_CMD_LOADS
+#undef CONFIG_CMD_IMLS
+
+#define CONFIG_CMD_CACHE
+#define CONFIG_CMD_PING 1
+#define CONFIG_CMD_DHCP 1
+#define CONFIG_CMD_NAND 1
+#define CONFIG_CMD_USB 1
+
+/* SDRAM */
+#define CONFIG_NR_DRAM_BANKS 1
+#define PHYS_SDRAM 0x20000000
+#define PHYS_SDRAM_SIZE 0x04000000 /* 64 megs */
+
+/* DataFlash */
+#define CONFIG_ATMEL_DATAFLASH_SPI
+#define CONFIG_HAS_DATAFLASH 1
+#define CONFIG_SYS_SPI_WRITE_TOUT (5 * CONFIG_SYS_HZ)
+#define CONFIG_SYS_MAX_DATAFLASH_BANKS 1
+#define CONFIG_SYS_DATAFLASH_LOGIC_ADDR_CS0 0xC0000000 /* CS0 */
+#define AT91_SPI_CLK 15000000
+#define DATAFLASH_TCSS (0x1a << 16)
+#define DATAFLASH_TCHS (0x1 << 24)
+
+/* NOR flash, if populated */
+#define CONFIG_SYS_FLASH_CFI 1
+#define CONFIG_FLASH_CFI_DRIVER 1
+#define PHYS_FLASH_1 0x10000000
+#define CONFIG_SYS_FLASH_BASE PHYS_FLASH_1
+#define CONFIG_SYS_MAX_FLASH_SECT 256
+#define CONFIG_SYS_MAX_FLASH_BANKS 1
+
+/* NAND flash */
+#ifdef CONFIG_CMD_NAND
+#define CONFIG_NAND_ATMEL
+#define CONFIG_SYS_MAX_NAND_DEVICE 1
+#define CONFIG_SYS_NAND_BASE 0x40000000
+#define CONFIG_SYS_NAND_DBW_8 1
+/* our ALE is AD21 */
+#define CONFIG_SYS_NAND_MASK_ALE (1 << 21)
+/* our CLE is AD22 */
+#define CONFIG_SYS_NAND_MASK_CLE (1 << 22)
+#define CONFIG_SYS_NAND_ENABLE_PIN GPIO_PIN_PD(15)
+#define CONFIG_SYS_NAND_READY_PIN GPIO_PIN_PB(30)
+
+#endif
+
+#define CONFIG_CMD_JFFS2 1
+#define CONFIG_JFFS2_CMDLINE 1
+#define CONFIG_JFFS2_NAND 1
+#define CONFIG_JFFS2_DEV "nand0" /* NAND device jffs2 lives on */
+#define CONFIG_JFFS2_PART_OFFSET 0 /* start of jffs2 partition */
+#define CONFIG_JFFS2_PART_SIZE (256 * 1024 * 1024) /* partition size*/
+
+/* PSRAM */
+#define PHYS_PSRAM 0x70000000
+#define PHYS_PSRAM_SIZE 0x00400000 /* 4MB */
+/* Slave EBI1, PSRAM connected */
+#define CONFIG_PSRAM_SCFG (AT91_MATRIX_SCFG_ARBT_FIXED_PRIORITY | \
+ AT91_MATRIX_SCFG_FIXED_DEFMSTR(5) | \
+ AT91_MATRIX_SCFG_DEFMSTR_TYPE_FIXED | \
+ AT91_MATRIX_SCFG_SLOT_CYCLE(255))
+
+/* Ethernet */
+#define CONFIG_MACB 1
+#define CONFIG_RMII 1
+#define CONFIG_NET_RETRY_COUNT 20
+#define CONFIG_RESET_PHY_R 1
+
+/* USB */
+#define CONFIG_USB_ATMEL
+#define CONFIG_USB_ATMEL_CLK_SEL_PLLB
+#define CONFIG_USB_OHCI_NEW 1
+#define CONFIG_DOS_PARTITION 1
+#define CONFIG_SYS_USB_OHCI_CPU_INIT 1
+#define CONFIG_SYS_USB_OHCI_REGS_BASE 0x00a00000 /* AT91SAM9263_UHP_BASE */
+#define CONFIG_SYS_USB_OHCI_SLOT_NAME "at91sam9263"
+#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 2
+#define CONFIG_USB_STORAGE 1
+
+#define CONFIG_SYS_LOAD_ADDR 0x22000000 /* load address */
+
+#define CONFIG_SYS_MEMTEST_START PHYS_SDRAM
+#define CONFIG_SYS_MEMTEST_END 0x23e00000
+
+#define CONFIG_SYS_USE_FLASH 1
+#undef CONFIG_SYS_USE_DATAFLASH
+#undef CONFIG_SYS_USE_NANDFLASH
+
+#ifdef CONFIG_SYS_USE_DATAFLASH
+
+/* bootstrap + u-boot + env + linux in dataflash on CS0 */
+#define CONFIG_ENV_IS_IN_DATAFLASH
+#define CFG_MONITOR_BASE (CFG_DATAFLASH_LOGIC_ADDR_CS0 + 0x8400)
+#define CONFIG_ENV_OFFSET 0x4200
+#define CONFIG_ENV_ADDR (CFG_DATAFLASH_LOGIC_ADDR_CS0 + CONFIG_ENV_OFFSET)
+#define CONFIG_ENV_SIZE 0x4200
+#define CONFIG_BOOTCOMMAND "cp.b 0xC0042000 0x22000000 0x210000; bootm"
+#define CONFIG_BOOTARGS "console=ttyS0,115200 " \
+ "root=/dev/mtdblock0 " \
+ "mtdparts=atmel_nand:-(root) "\
+ "rw rootfstype=jffs2"
+
+#elif defined(CONFIG_SYS_USE_NANDFLASH) /* CFG_USE_NANDFLASH */
+
+/* bootstrap + u-boot + env + linux in nandflash */
+#define CONFIG_ENV_IS_IN_NAND
+#define CONFIG_ENV_OFFSET 0x60000
+#define CONFIG_ENV_OFFSET_REDUND 0x80000
+#define CONFIG_ENV_SIZE 0x20000 /* 1 sector = 128 kB */
+#define CONFIG_BOOTCOMMAND "nand read 0x22000000 0xA0000 0x200000; bootm"
+#define CONFIG_BOOTARGS "console=ttyS0,115200 " \
+ "root=/dev/mtdblock5 " \
+ "mtdparts=atmel_nand:" \
+ "128k(bootstrap)ro," \
+ "256k(uboot)ro," \
+ "128k(env1)ro," \
+ "128k(env2)ro," \
+ "2M(linux)," \
+ "-(root) " \
+ "rw rootfstype=jffs2"
+
+#elif defined(CONFIG_SYS_USE_FLASH) /* CFG_USE_FLASH */
+
+#define CONFIG_ENV_IS_IN_FLASH 1
+#define CONFIG_ENV_OFFSET 0x40000
+#define CONFIG_ENV_SECT_SIZE 0x10000
+#define CONFIG_ENV_SIZE 0x10000
+#define CONFIG_ENV_OVERWRITE 1
+
+/* JFFS Partition offset set */
+#define CONFIG_SYS_JFFS2_FIRST_BANK 0
+#define CONFIG_SYS_JFFS2_NUM_BANKS 1
+
+/* 512k reserved for u-boot */
+#define CONFIG_SYS_JFFS2_FIRST_SECTOR 11
+
+#define CONFIG_BOOTCOMMAND "run flashboot"
+#define CONFIG_ROOTPATH "/ronetix/rootfs"
+#define CONFIG_AUTOBOOT_PROMPT "autoboot in %d seconds\n", bootdelay
+
+#define CONFIG_CON_ROT "fbcon=rotate:3 "
+#define CONFIG_BOOTARGS "root=/dev/mtdblock4 rootfstype=jffs2 "\
+ CONFIG_CON_ROT
+
+#define MTDIDS_DEFAULT "nor0=physmap-flash.0,nand0=nand"
+#define MTDPARTS_DEFAULT \
+ "mtdparts=physmap-flash.0:" \
+ "256k(u-boot)ro," \
+ "64k(u-boot-env)ro," \
+ "1408k(kernel)," \
+ "-(rootfs);" \
+ "nand:-(nand)"
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "mtdids=" MTDIDS_DEFAULT "\0" \
+ "mtdparts=" MTDPARTS_DEFAULT "\0" \
+ "partition=nand0,0\0" \
+ "ramargs=setenv bootargs $(bootargs) $(mtdparts)\0" \
+ "nfsargs=setenv bootargs root=/dev/nfs rw " \
+ CONFIG_CON_ROT \
+ "nfsroot=$(serverip):$(rootpath) $(mtdparts)\0" \
+ "addip=setenv bootargs $(bootargs) " \
+ "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask)"\
+ ":$(hostname):eth0:off\0" \
+ "ramboot=tftpboot 0x22000000 vmImage;" \
+ "run ramargs;run addip;bootm 22000000\0" \
+ "nfsboot=tftpboot 0x22000000 vmImage;" \
+ "run nfsargs;run addip;bootm 22000000\0" \
+ "flashboot=run ramargs;run addip;bootm 0x10050000\0" \
+ ""
+
+#else
+#error "Undefined memory device"
+#endif
+
+#define CONFIG_BAUDRATE 115200
+
+#define CONFIG_SYS_PROMPT "u-boot-pm9263> "
+#define CONFIG_SYS_CBSIZE 256
+#define CONFIG_SYS_MAXARGS 16
+#define CONFIG_SYS_PBSIZE \
+ (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
+#define CONFIG_SYS_LONGHELP 1
+#define CONFIG_CMDLINE_EDITING 1
+
+/*
+ * Size of malloc() pool
+ */
+#define CONFIG_SYS_MALLOC_LEN ROUND(3 * CONFIG_ENV_SIZE + 128 * 1024, 0x1000)
+
+#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM
+#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_SDRAM_BASE + 0x1000 - \
+ GENERATED_GBL_DATA_SIZE)
+
+#endif
Code Review / kvmfornfv.git / blobdiff