--- /dev/null
+/*
+ * (C) Copyright 2006-2009
+ * Texas Instruments Incorporated.
+ * Richard Woodruff <r-woodruff2@ti.com>
+ * Syed Mohammed Khasim <x0khasim@ti.com>
+ * Nishanth Menon <nm@ti.com>
+ *
+ * Configuration settings for the 3430 TI SDP3430 board.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/* TODO: REMOVE THE FOLLOWING
+ * Retained the following till size.h is removed in u-boot
+ */
+#include <linux/sizes.h>
+/*
+ * High Level Configuration Options
+ */
+#define CONFIG_OMAP 1 /* in a TI OMAP core */
+#define CONFIG_OMAP34XX 1 /* which is a 34XX */
+#define CONFIG_OMAP3_3430SDP 1 /* working with SDP Rev2 */
+#define CONFIG_OMAP_COMMON
+
+#define CONFIG_SDRC /* The chip has SDRC controller */
+
+#include <asm/arch/cpu.h> /* get chip and board defs */
+#include <asm/arch/omap3.h>
+
+/*
+ * NOTE: these #defines presume standard SDP jumper settings.
+ * In particular:
+ * - 26 MHz clock (not 19.2 or 38.4 MHz)
+ * - Boot from 128MB NOR, not NAND or OneNAND
+ *
+ * At this writing, OMAP3 U-Boot support doesn't permit concurrent
+ * support for all the flash types the board supports.
+ */
+#define CONFIG_DISPLAY_CPUINFO 1
+#define CONFIG_DISPLAY_BOARDINFO 1
+
+/* Clock Defines */
+#define V_OSCK 26000000 /* Clock output from T2 */
+#define V_SCLK (V_OSCK >> 1)
+
+#define CONFIG_MISC_INIT_R
+
+#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */
+#define CONFIG_SETUP_MEMORY_TAGS 1
+#define CONFIG_INITRD_TAG 1
+#define CONFIG_REVISION_TAG 1
+
+#define CONFIG_OF_LIBFDT 1
+
+/*
+ * Size of malloc() pool
+ * Total Size Environment - 256k
+ * Malloc - add 256k
+ */
+#define CONFIG_ENV_SIZE (256 << 10)
+#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + (256 << 10))
+
+/*--------------------------------------------------------------------------*/
+
+/*
+ * Hardware drivers
+ */
+
+/*
+ * TWL4030
+ */
+#define CONFIG_TWL4030_POWER 1
+
+/*
+ * serial port - NS16550 compatible
+ */
+#define V_NS16550_CLK 48000000 /* 48MHz (APLL96/2) */
+
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE (-4)
+#define CONFIG_SYS_NS16550_CLK V_NS16550_CLK
+
+/* Original SDP u-boot used UART1 and thus J8 (innermost); that can be
+ * swapped with UART2 via jumpering. Downsides of using J8: it doesn't
+ * support UART boot (that's only for UART3); it prevents sharing a Linux
+ * kernel (LL_DEBUG_UART3) or filesystem (getty ttyS2) with most boards.
+ *
+ * UART boot uses UART3 on J9, and the SDP user's guide says to use
+ * that for console. Downsides of using J9: you can't use IRDA too;
+ * since UART3 isn't in the CORE power domain, it may be a bit less
+ * usable in certain PM-sensitive debug scenarios.
+ */
+#undef CONSOLE_J9 /* else J8/UART1 (innermost) */
+
+#ifdef CONSOLE_J9
+#define CONFIG_CONS_INDEX 3
+#define CONFIG_SYS_NS16550_COM3 OMAP34XX_UART3
+#define CONFIG_SERIAL3 3 /* UART3 */
+#else
+#define CONFIG_CONS_INDEX 1
+#define CONFIG_SYS_NS16550_COM1 OMAP34XX_UART1
+#define CONFIG_SERIAL1 1 /* UART1 */
+#endif
+
+#define CONFIG_ENV_OVERWRITE
+#define CONFIG_BAUDRATE 115200
+#define CONFIG_SYS_BAUDRATE_TABLE {4800, 9600, 19200, 38400, 57600,\
+ 115200}
+
+/*
+ * I2C for power management setup
+ */
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_OMAP24_I2C_SPEED 100000
+#define CONFIG_SYS_OMAP24_I2C_SLAVE 1
+#define CONFIG_SYS_I2C_OMAP34XX
+
+/* OMITTED: single 1 Gbit MT29F1G NAND flash */
+
+/*
+ * NOR boot support - single 1 Gbit PF48F6000M0 Strataflash
+ */
+#define CONFIG_SYS_FLASH_BASE 0x10000000
+#define CONFIG_FLASH_CFI_DRIVER 1 /* Use drivers/cfi_flash.c */
+#define CONFIG_SYS_FLASH_CFI 1 /* use CFI geometry data */
+#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* ~10x faster writes */
+#define CONFIG_SYS_FLASH_PROTECTION 1 /* hardware sector protection */
+#define CONFIG_SYS_FLASH_EMPTY_INFO 1 /* flinfo 'E' for empty */
+#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE}
+#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of flash banks */
+
+#define CONFIG_SYS_FLASH_CFI_WIDTH 2
+#define PHYS_FLASH_SIZE (128 << 20)
+#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max sectors on one chip */
+
+/* OMITTED: single 2 Gbit KFM2G16 OneNAND flash */
+
+#define CONFIG_ENV_IS_IN_FLASH 1
+#define CONFIG_SYS_ENV_SECT_SIZE (256 << 10)
+#define CONFIG_ENV_OFFSET CONFIG_SYS_ENV_SECT_SIZE
+#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + CONFIG_SYS_ENV_SECT_SIZE)
+/*--------------------------------------------------------------------------*/
+
+/* commands to include */
+#include <config_cmd_default.h>
+
+/* Enabled commands */
+#define CONFIG_CMD_DHCP /* DHCP Support */
+#define CONFIG_CMD_EXT2 /* EXT2 Support */
+#define CONFIG_CMD_FAT /* FAT support */
+#define CONFIG_CMD_I2C /* I2C serial bus support */
+#define CONFIG_CMD_JFFS2 /* JFFS2 Support */
+#define CONFIG_CMD_MMC /* MMC support */
+#define CONFIG_CMD_NET
+
+/* Disabled commands */
+#undef CONFIG_CMD_FPGA /* FPGA configuration Support */
+#undef CONFIG_CMD_IMLS /* List all found images */
+
+/*--------------------------------------------------------------------------*/
+/*
+ * MMC boot support
+ */
+
+#if defined(CONFIG_CMD_MMC)
+#define CONFIG_GENERIC_MMC 1
+#define CONFIG_MMC 1
+#define CONFIG_OMAP_HSMMC 1
+#define CONFIG_DOS_PARTITION 1
+#endif
+
+/*----------------------------------------------------------------------------
+ * SMSC9115 Ethernet from SMSC9118 family
+ *----------------------------------------------------------------------------
+ */
+#if defined(CONFIG_CMD_NET)
+
+#define CONFIG_LAN91C96
+#define CONFIG_LAN91C96_BASE DEBUG_BASE
+#define CONFIG_LAN91C96_EXT_PHY
+
+#define CONFIG_BOOTP_SEND_HOSTNAME
+/*
+ * BOOTP fields
+ */
+#define CONFIG_BOOTP_SUBNETMASK 0x00000001
+#define CONFIG_BOOTP_GATEWAY 0x00000002
+#define CONFIG_BOOTP_HOSTNAME 0x00000004
+#define CONFIG_BOOTP_BOOTPATH 0x00000010
+#endif /* (CONFIG_CMD_NET) */
+
+/*
+ * Environment setup
+ *
+ * Default boot order: mmc bootscript, MMC uImage, NOR image.
+ * Network booting environment must be configured at site.
+ */
+
+/* allow overwriting serial config and ethaddr */
+#define CONFIG_ENV_OVERWRITE
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "loadaddr=0x82000000\0" \
+ "console=ttyS0,115200n8\0" \
+ "mmcargs=setenv bootargs console=${console} " \
+ "root=/dev/mmcblk0p2 rw " \
+ "rootfstype=ext3 rootwait\0" \
+ "norargs=setenv bootargs console=${console} " \
+ "root=/dev/mtdblock3 rw " \
+ "rootfstype=jffs2\0" \
+ "loadbootscript=fatload mmc 0 ${loadaddr} boot.scr\0" \
+ "bootscript=echo Running bootscript from MMC/SD ...; " \
+ "autoscr ${loadaddr}\0" \
+ "loaduimage=fatload mmc 0 ${loadaddr} uImage\0" \
+ "mmcboot=echo Booting from MMC/SD ...; " \
+ "run mmcargs; " \
+ "bootm ${loadaddr}\0" \
+ "norboot=echo Booting from NOR ...; " \
+ "run norargs; " \
+ "bootm 0x80000\0" \
+
+#define CONFIG_BOOTCOMMAND \
+ "if mmcinit; then " \
+ "if run loadbootscript; then " \
+ "run bootscript; " \
+ "else " \
+ "if run loaduimage; then " \
+ "run mmcboot; " \
+ "else run norboot; " \
+ "fi; " \
+ "fi; " \
+ "else run norboot; fi"
+
+#define CONFIG_AUTO_COMPLETE 1
+
+/*--------------------------------------------------------------------------*/
+
+/*
+ * Miscellaneous configurable options
+ */
+
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#define CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */
+#define CONFIG_SYS_PROMPT "OMAP34XX SDP # "
+#define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */
+/* Print Buffer Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
+ sizeof(CONFIG_SYS_PROMPT) + 16)
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+/* Boot Argument Buffer Size */
+#define CONFIG_SYS_BARGSIZE (CONFIG_SYS_CBSIZE)
+
+/* SDRAM Test range - start at 16 meg boundary -ends at 32Meg -
+ * a basic sanity check ONLY
+ * IF you would like to increase coverage, increase the end address
+ * or run the test with custom options
+ */
+#define CONFIG_SYS_MEMTEST_START (OMAP34XX_SDRC_CS0 + 0x01000000)
+#define CONFIG_SYS_MEMTEST_END (OMAP34XX_SDRC_CS0 + (32 << 20))
+
+/* Default load address */
+#define CONFIG_SYS_LOAD_ADDR (OMAP34XX_SDRC_CS0)
+
+/*--------------------------------------------------------------------------*/
+
+/*
+ * 3430 has 12 GP timers, they can be driven by the SysClk (12/13/19.2) or by
+ * 32KHz clk, or from external sig. This rate is divided by a local divisor.
+ */
+#define CONFIG_SYS_TIMERBASE (OMAP34XX_GPT2)
+#define CONFIG_SYS_PTV 2 /* Divisor: 2^(PTV+1) => 8 */
+
+#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
+#define CONFIG_SYS_INIT_RAM_ADDR 0x4020f800
+#define CONFIG_SYS_INIT_RAM_SIZE 0x800
+#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + \
+ CONFIG_SYS_INIT_RAM_SIZE - \
+ GENERATED_GBL_DATA_SIZE)
+/*
+ * SDRAM Memory Map
+ */
+#define CONFIG_NR_DRAM_BANKS 2 /* CS1 may or may not be populated */
+#define PHYS_SDRAM_1 OMAP34XX_SDRC_CS0
+#define PHYS_SDRAM_2 OMAP34XX_SDRC_CS1
+
+/*--------------------------------------------------------------------------*/
+
+/*
+ * NOR FLASH usage ... default nCS0:
+ * - one 256KB sector for U-Boot
+ * - one 256KB sector for its parameters (not all used)
+ * - eight sectors (2 MB) for kernel
+ * - rest for JFFS2
+ */
+
+/* Monitor at start of flash */
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
+#define CONFIG_SYS_MONITOR_LEN (256 << 10)
+
+/*
+ * NAND FLASH usage ... default nCS1:
+ * - four 128KB sectors for X-Loader
+ * - four 128KB sectors for U-Boot
+ * - two 128KB sector for its parameters
+ * - 32 sectors (4 MB) for kernel
+ * - rest for filesystem
+ */
+
+/*
+ * OneNAND FLASH usage ... default nCS2:
+ * - four 128KB sectors for X-Loader
+ * - two 128KB sectors for U-Boot
+ * - one 128KB sector for its parameters
+ * - sixteen sectors (2 MB) for kernel
+ * - rest for filesystem
+ */
+
+#define CONFIG_SYS_CACHELINE_SIZE 64
+
+#endif /* __CONFIG_H */
Code Review / kvmfornfv.git / blobdiff