Add qemu 2.4.0

[kvmfornfv.git] / qemu / roms / u-boot / include / configs / nios2-generic.h

diff --git a/qemu/roms/u-boot/include/configs/nios2-generic.h b/qemu/roms/u-boot/include/configs/nios2-generic.h
new file mode 100644 (file)
index 0000000..1578b01
--- /dev/null
+++ b/qemu/roms/u-boot/include/configs/nios2-generic.h
@@ -0,0 +1,135 @@
+/*
+ * (C) Copyright 2005, Psyent Corporation <www.psyent.com>
+ * Scott McNutt <smcnutt@psyent.com>
+ * (C) Copyright 2010, Thomas Chou <thomas@wytron.com.tw>
+ *
+ * SPDX-License-Identifier:    GPL-2.0+
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * BOARD/CPU
+ */
+#include "../board/altera/nios2-generic/custom_fpga.h" /* fpga parameters */
+#define CONFIG_BOARD_NAME "nios2-generic" /* custom board name */
+#define CONFIG_BOARD_EARLY_INIT_F      /* enable early board-spec. init */
+#define CONFIG_SYS_NIOS_SYSID_BASE     CONFIG_SYS_SYSID_BASE
+
+/*
+ * SERIAL
+ */
+#define CONFIG_ALTERA_UART
+#if defined(CONFIG_ALTERA_JTAG_UART)
+# define CONFIG_SYS_NIOS_CONSOLE       CONFIG_SYS_JTAG_UART_BASE
+#else
+# define CONFIG_SYS_NIOS_CONSOLE       CONFIG_SYS_UART_BASE
+#endif
+
+#define CONFIG_ALTERA_JTAG_UART_BYPASS
+#define CONFIG_SYS_NIOS_FIXEDBAUD
+#define CONFIG_BAUDRATE                CONFIG_SYS_UART_BAUD
+#define CONFIG_SYS_BAUDRATE_TABLE      {CONFIG_BAUDRATE}
+#define CONFIG_SYS_CONSOLE_INFO_QUIET  /* Suppress console info */
+
+/*
+ * TIMER
+ */
+#define CONFIG_SYS_LOW_RES_TIMER
+#define CONFIG_SYS_NIOS_TMRBASE        CONFIG_SYS_TIMER_BASE
+#define CONFIG_SYS_NIOS_TMRIRQ         CONFIG_SYS_TIMER_IRQ
+#define CONFIG_SYS_NIOS_TMRMS          10      /* Desired period (msec)*/
+#define CONFIG_SYS_NIOS_TMRCNT \
+       (CONFIG_SYS_NIOS_TMRMS * (CONFIG_SYS_TIMER_FREQ / 1000) - 1)
+
+/*
+ * STATUS LED
+ */
+#define CONFIG_ALTERA_PIO
+#define CONFIG_SYS_ALTERA_PIO_NUM      1
+#define CONFIG_SYS_ALTERA_PIO_GPIO_NUM LED_PIO_WIDTH
+
+#define CONFIG_STATUS_LED              /* Enable status driver */
+#define CONFIG_BOARD_SPECIFIC_LED
+#define CONFIG_GPIO_LED                /* Enable GPIO LED driver */
+#define CONFIG_GPIO                    /* Enable GPIO driver */
+
+#define STATUS_LED_BIT                 0       /* Bit-0 on GPIO */
+#define STATUS_LED_STATE               1       /* Blinking */
+#define STATUS_LED_PERIOD      (500 / CONFIG_SYS_NIOS_TMRMS) /* 500 msec */
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+#undef CONFIG_CMD_BOOTD
+#undef CONFIG_CMD_FPGA
+#undef CONFIG_CMD_IMLS
+#undef CONFIG_CMD_ITEST
+#undef CONFIG_CMD_NFS
+#undef CONFIG_CMD_SETGETDCR
+#undef CONFIG_CMD_XIMG
+
+#ifdef CONFIG_CMD_NET
+# define CONFIG_CMD_DHCP
+# define CONFIG_CMD_PING
+#endif
+
+/*
+ * ENVIRONMENT -- Put environment in sector CONFIG_SYS_MONITOR_LEN above
+ * CONFIG_SYS_RESET_ADDR, since we assume the monitor is stored at the
+ * reset address, no? This will keep the environment in user region
+ * of flash. NOTE: the monitor length must be multiple of sector size
+ * (which is common practice).
+ */
+#define CONFIG_ENV_IS_IN_FLASH
+
+#define CONFIG_ENV_SIZE                0x10000 /* 64k, 1 sector */
+#define CONFIG_ENV_OVERWRITE           /* Serial change Ok     */
+#define CONFIG_ENV_ADDR                ((CONFIG_SYS_RESET_ADDR + \
+                                         CONFIG_SYS_MONITOR_LEN) | \
+                                        CONFIG_SYS_FLASH_BASE)
+
+/*
+ * MEMORY ORGANIZATION
+ * -Monitor at top of sdram.
+ * -The heap is placed below the monitor
+ * -The stack is placed below the heap (&grows down).
+ */
+#define CONFIG_MONITOR_IS_IN_RAM
+#define CONFIG_SYS_MONITOR_LEN         0x40000 /* Reserve 256k */
+#define CONFIG_SYS_MONITOR_BASE        (CONFIG_SYS_SDRAM_BASE + \
+                                        CONFIG_SYS_SDRAM_SIZE - \
+                                        CONFIG_SYS_MONITOR_LEN)
+#define CONFIG_SYS_MALLOC_LEN          (CONFIG_ENV_SIZE + 0x20000)
+#define CONFIG_SYS_MALLOC_BASE         (CONFIG_SYS_MONITOR_BASE - \
+                                        CONFIG_SYS_MALLOC_LEN)
+#define CONFIG_SYS_INIT_SP             CONFIG_SYS_MALLOC_BASE
+
+/*
+ * MISC
+ */
+#define CONFIG_SYS_LONGHELP            /* Provide extended help */
+#define CONFIG_SYS_CBSIZE              256     /* Console I/O buf size */
+#define CONFIG_SYS_MAXARGS             16      /* Max command args     */
+#define CONFIG_SYS_BARGSIZE            CONFIG_SYS_CBSIZE /* Bootarg buf size */
+#define CONFIG_SYS_PBSIZE              (CONFIG_SYS_CBSIZE + \
+                                       sizeof(CONFIG_SYS_PROMPT) + \
+                                        16)    /* Print buf size */
+#define CONFIG_SYS_LOAD_ADDR           CONFIG_SYS_SDRAM_BASE
+#define CONFIG_SYS_MEMTEST_START       CONFIG_SYS_SDRAM_BASE
+#define CONFIG_SYS_MEMTEST_END         (CONFIG_SYS_INIT_SP - 0x20000)
+#define CONFIG_CMDLINE_EDITING
+
+#define CONFIG_SYS_HUSH_PARSER
+
+#endif /* __CONFIG_H */