--- /dev/null
+/*
+ * (C) Copyright 2007-2008
+ * Dirk Eibach, Guntermann & Drunck GmbH, eibach@gdsys.de
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+
+#define CONFIG_405EP 1 /* this is a PPC405 CPU */
+#define CONFIG_NEO 1 /* on a Neo board */
+
+#define CONFIG_SYS_TEXT_BASE 0xFFFC0000
+
+/*
+ * Include common defines/options for all AMCC eval boards
+ */
+#define CONFIG_HOSTNAME neo
+#define CONFIG_IDENT_STRING " neo 0.02"
+#include "amcc-common.h"
+
+#define CONFIG_BOARD_EARLY_INIT_F
+#define CONFIG_BOARD_EARLY_INIT_R
+#define CONFIG_MISC_INIT_R
+#define CONFIG_LAST_STAGE_INIT
+
+#define CONFIG_SYS_CLK_FREQ 33333333 /* external frequency to pll */
+
+/*
+ * Configure PLL
+ */
+#define PLLMR0_DEFAULT PLLMR0_266_133_66_33
+#define PLLMR1_DEFAULT PLLMR1_266_133_66_33
+
+/* new uImage format support */
+#define CONFIG_FIT
+#define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */
+
+#define CONFIG_ENV_IS_IN_FLASH /* use FLASH for environment vars */
+
+/*
+ * Default environment variables
+ */
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ CONFIG_AMCC_DEF_ENV \
+ CONFIG_AMCC_DEF_ENV_POWERPC \
+ CONFIG_AMCC_DEF_ENV_NOR_UPD \
+ "kernel_addr=fc000000\0" \
+ "fdt_addr=fc1e0000\0" \
+ "ramdisk_addr=fc200000\0" \
+ ""
+
+#define CONFIG_PHY_ADDR 4 /* PHY address */
+#define CONFIG_HAS_ETH0
+#define CONFIG_HAS_ETH1
+#define CONFIG_PHY1_ADDR 0xc /* EMAC1 PHY address */
+#define CONFIG_PHY_CLK_FREQ EMAC_STACR_CLK_66MHZ
+
+/*
+ * Commands additional to the ones defined in amcc-common.h
+ */
+#define CONFIG_CMD_CACHE
+#define CONFIG_CMD_DATE
+#define CONFIG_CMD_DTT
+#undef CONFIG_CMD_EEPROM
+
+/*
+ * SDRAM configuration (please see cpu/ppc/sdram.[ch])
+ */
+#define CONFIG_SDRAM_BANK0 1 /* init onboard SDRAM bank 0 */
+
+/* SDRAM timings used in datasheet */
+#define CONFIG_SYS_SDRAM_CL 3 /* CAS latency */
+#define CONFIG_SYS_SDRAM_tRP 20 /* PRECHARGE command period */
+#define CONFIG_SYS_SDRAM_tRC 66 /* ACTIVE-to-ACTIVE command period */
+#define CONFIG_SYS_SDRAM_tRCD 20 /* ACTIVE-to-READ delay */
+#define CONFIG_SYS_SDRAM_tRFC 66 /* Auto refresh period */
+
+/*
+ * If CONFIG_SYS_EXT_SERIAL_CLOCK, then the UART divisor is 1.
+ * If CONFIG_SYS_405_UART_ERRATA_59, then UART divisor is 31.
+ * Otherwise, UART divisor is determined by CPU Clock and CONFIG_SYS_BASE_BAUD value.
+ * The Linux BASE_BAUD define should match this configuration.
+ * baseBaud = cpuClock/(uartDivisor*16)
+ * If CONFIG_SYS_405_UART_ERRATA_59 and 200MHz CPU clock,
+ * set Linux BASE_BAUD to 403200.
+ */
+#define CONFIG_CONS_INDEX 1 /* Use UART0 */
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE 1
+#define CONFIG_SYS_NS16550_CLK get_serial_clock()
+
+#undef CONFIG_SYS_EXT_SERIAL_CLOCK /* external serial clock */
+#undef CONFIG_SYS_405_UART_ERRATA_59 /* 405GP/CR Rev. D silicon */
+#define CONFIG_SYS_BASE_BAUD 691200
+
+/*
+ * I2C stuff
+ */
+#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 100000
+
+/* RTC */
+#define CONFIG_RTC_DS1337
+#define CONFIG_SYS_I2C_RTC_ADDR 0x68
+
+/* Temp sensor/hwmon/dtt */
+#define CONFIG_DTT_LM63 1 /* National LM63 */
+#define CONFIG_DTT_SENSORS { 0 } /* Sensor addresses */
+#define CONFIG_DTT_PWM_LOOKUPTABLE \
+ { { 40, 10 }, { 50, 20 }, { 60, 40 } }
+#define CONFIG_DTT_TACH_LIMIT 0xa10
+
+/*
+ * FLASH organization
+ */
+#define CONFIG_SYS_FLASH_CFI /* The flash is CFI compatible */
+#define CONFIG_FLASH_CFI_DRIVER /* Use common CFI driver */
+
+#define CONFIG_SYS_FLASH_BASE 0xFC000000
+#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE }
+
+#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
+#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max number of sectors on one chip */
+
+#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
+
+#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */
+
+#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
+#define CONFIG_SYS_FLASH_QUIET_TEST 1 /* don't warn upon unknown flash */
+
+#ifdef CONFIG_ENV_IS_IN_FLASH
+#define CONFIG_ENV_SECT_SIZE 0x20000 /* size of one complete sector */
+#define CONFIG_ENV_ADDR 0xFFF00000
+#define CONFIG_ENV_SIZE 0x20000 /* Total Size of Environment Sector */
+
+/* Address and size of Redundant Environment Sector */
+#define CONFIG_ENV_ADDR_REDUND 0xFFF20000
+#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
+#endif
+
+/*
+ * PPC405 GPIO Configuration
+ */
+#define CONFIG_SYS_4xx_GPIO_TABLE { \
+{ \
+/* GPIO Core 0 */ \
+{ GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO0 PerBLast */ \
+{ GPIO_BASE, GPIO_OUT, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO1 TS1E */ \
+{ GPIO_BASE, GPIO_OUT, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO2 TS2E */ \
+{ GPIO_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO3 TS1O */ \
+{ GPIO_BASE, GPIO_OUT, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO4 TS2O */ \
+{ GPIO_BASE, GPIO_OUT, GPIO_SEL, GPIO_OUT_1 }, /* GPIO5 TS3 */ \
+{ GPIO_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO6 TS4 */ \
+{ GPIO_BASE, GPIO_OUT, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO7 TS5 */ \
+{ GPIO_BASE, GPIO_OUT, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO8 TS6 */ \
+{ GPIO_BASE, GPIO_OUT, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO9 TrcClk */ \
+{ GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO10 PerCS1 */ \
+{ GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO11 PerCS2 */ \
+{ GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO12 PerCS3 */ \
+{ GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO13 PerCS4 */ \
+{ GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO14 PerAddr03 */ \
+{ GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO15 PerAddr04 */ \
+{ GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO16 PerAddr05 */ \
+{ GPIO_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO17 IRQ0 */ \
+{ GPIO_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO18 IRQ1 */ \
+{ GPIO_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO19 IRQ2 */ \
+{ GPIO_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO20 IRQ3 */ \
+{ GPIO_BASE, GPIO_OUT, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO21 IRQ4 */ \
+{ GPIO_BASE, GPIO_OUT, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO22 IRQ5 */ \
+{ GPIO_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO23 IRQ6 */ \
+{ GPIO_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO24 UART0_DCD */ \
+{ GPIO_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO25 UART0_DSR */ \
+{ GPIO_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO26 UART0_RI */ \
+{ GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO27 UART0_DTR */ \
+{ GPIO_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO28 UART1_Rx */ \
+{ GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO29 UART1_Tx */ \
+{ GPIO_BASE, GPIO_OUT, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO30 RejectPkt0 */ \
+{ GPIO_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO31 RejectPkt1 */ \
+} \
+}
+
+/*
+ * Definitions for initial stack pointer and data area (in data cache)
+ */
+/* use on chip memory (OCM) for temperary stack until sdram is tested */
+#define CONFIG_SYS_TEMP_STACK_OCM 1
+
+/* On Chip Memory location */
+#define CONFIG_SYS_OCM_DATA_ADDR 0xF8000000
+#define CONFIG_SYS_OCM_DATA_SIZE 0x1000
+#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_DATA_ADDR /* inside of SDRAM */
+#define CONFIG_SYS_INIT_RAM_SIZE CONFIG_SYS_OCM_DATA_SIZE /* Size of used area in RAM */
+
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
+
+/*
+ * External Bus Controller (EBC) Setup
+ */
+
+/* Memory Bank 0 (NOR-FLASH) initialization */
+#define CONFIG_SYS_EBC_PB0AP 0x92015480
+#define CONFIG_SYS_EBC_PB0CR 0xFC0DA000 /* BAS=0xFC0,BS=64MB,BU=R/W,BW=16bit */
+
+/* Memory Bank 1 (NVRAM) initialization */
+#define CONFIG_SYS_EBC_PB1AP 0x92015480
+#define CONFIG_SYS_EBC_PB1CR 0xFB85A000 /* BAS=0xFF8,BS=4MB,BU=R/W,BW=8bit */
+
+/* Memory Bank 2 (FPGA) initialization */
+#define CONFIG_SYS_FPGA0_BASE 0x7f100000
+#define CONFIG_SYS_EBC_PB2AP 0x92015480
+#define CONFIG_SYS_EBC_PB2CR 0x7f11a000 /* BAS=0x7f1,BS=1MB,BU=R/W,BW=16bit */
+
+#define CONFIG_SYS_FPGA_BASE(k) CONFIG_SYS_FPGA0_BASE
+
+#define CONFIG_SYS_FPGA_COUNT 1
+
+#define CONFIG_SYS_FPGA_PTR \
+ { (struct ihs_fpga *)CONFIG_SYS_FPGA0_BASE }
+
+#define CONFIG_SYS_FPGA_COMMON
+
+/* Memory Bank 3 (Latches) initialization */
+#define CONFIG_SYS_LATCH_BASE 0x7f200000
+#define CONFIG_SYS_EBC_PB3AP 0x92015480
+#define CONFIG_SYS_EBC_PB3CR 0x7f21a000 /* BAS=0x7f2,BS=1MB,BU=R/W,BW=16bit */
+
+#define CONFIG_SYS_LATCH0_RESET 0xffff
+#define CONFIG_SYS_LATCH0_BOOT 0xffff
+#define CONFIG_SYS_LATCH1_RESET 0xffbf
+#define CONFIG_SYS_LATCH1_BOOT 0xffff
+
+#endif /* __CONFIG_H */
Code Review / kvmfornfv.git / blobdiff