--- /dev/null
+/*
+ * (C) Copyright 2011 Freescale Semiconductor, Inc.
+ * Author: Fabio Estevam <fabio.estevam@freescale.com>
+ *
+ * Based on m28evk.h:
+ * Copyright (C) 2011 Marek Vasut <marek.vasut@gmail.com>
+ * on behalf of DENX Software Engineering GmbH
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+#ifndef __CONFIGS_MX28EVK_H__
+#define __CONFIGS_MX28EVK_H__
+
+/* System configurations */
+#define CONFIG_MX28 /* i.MX28 SoC */
+#define CONFIG_MACH_TYPE MACH_TYPE_MX28EVK
+
+/* U-Boot Commands */
+#define CONFIG_SYS_NO_FLASH
+#include <config_cmd_default.h>
+#define CONFIG_DISPLAY_CPUINFO
+#define CONFIG_DOS_PARTITION
+
+#define CONFIG_CMD_CACHE
+#define CONFIG_CMD_DATE
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_GPIO
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_MMC
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_NFS
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_SAVEENV
+#define CONFIG_CMD_SETEXPR
+#define CONFIG_CMD_SF
+#define CONFIG_CMD_SPI
+#define CONFIG_CMD_USB
+#define CONFIG_CMD_BOOTZ
+#define CONFIG_CMD_NAND
+#define CONFIG_CMD_NAND_TRIMFFS
+#define CONFIG_VIDEO
+
+/* Memory configuration */
+#define CONFIG_NR_DRAM_BANKS 1 /* 1 bank of DRAM */
+#define PHYS_SDRAM_1 0x40000000 /* Base address */
+#define PHYS_SDRAM_1_SIZE 0x40000000 /* Max 1 GB RAM */
+#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
+
+/* Environment */
+#define CONFIG_ENV_SIZE (16 * 1024)
+#define CONFIG_ENV_OVERWRITE
+
+/* Environment is in MMC */
+#if defined(CONFIG_CMD_MMC) && defined(CONFIG_ENV_IS_IN_MMC)
+#define CONFIG_ENV_OFFSET (256 * 1024)
+#define CONFIG_SYS_MMC_ENV_DEV 0
+#endif
+
+/* Environment is in NAND */
+#if defined(CONFIG_CMD_NAND) && defined(CONFIG_ENV_IS_IN_NAND)
+#define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE
+#define CONFIG_ENV_SECT_SIZE (128 * 1024)
+#define CONFIG_ENV_RANGE (512 * 1024)
+#define CONFIG_ENV_OFFSET 0x300000
+#define CONFIG_ENV_OFFSET_REDUND \
+ (CONFIG_ENV_OFFSET + CONFIG_ENV_RANGE)
+#endif
+
+/* Environemnt is in SPI flash */
+#if defined(CONFIG_CMD_SF) && defined(CONFIG_ENV_IS_IN_SPI_FLASH)
+#define CONFIG_SYS_REDUNDAND_ENVIRONMENT
+#define CONFIG_ENV_SIZE 0x1000 /* 4KB */
+#define CONFIG_ENV_OFFSET 0x40000 /* 256K */
+#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)
+#define CONFIG_ENV_SECT_SIZE 0x1000
+#define CONFIG_ENV_SPI_CS 0
+#define CONFIG_ENV_SPI_BUS 2
+#define CONFIG_ENV_SPI_MAX_HZ 24000000
+#define CONFIG_ENV_SPI_MODE SPI_MODE_0
+#endif
+
+/* UBI and NAND partitioning */
+#ifdef CONFIG_CMD_NAND
+#define CONFIG_CMD_UBI
+#define CONFIG_CMD_UBIFS
+#define CONFIG_CMD_MTDPARTS
+#define CONFIG_RBTREE
+#define CONFIG_LZO
+#define CONFIG_MTD_DEVICE
+#define CONFIG_MTD_PARTITIONS
+#define MTDIDS_DEFAULT "nand0=gpmi-nand"
+#define MTDPARTS_DEFAULT \
+ "mtdparts=gpmi-nand:" \
+ "3m(bootloader)ro," \
+ "512k(environment)," \
+ "512k(redundant-environment)," \
+ "4m(kernel)," \
+ "512k(fdt)," \
+ "8m(ramdisk)," \
+ "-(filesystem)"
+#endif
+
+/* FEC Ethernet on SoC */
+#ifdef CONFIG_CMD_NET
+#define CONFIG_FEC_MXC
+#define CONFIG_NET_MULTI
+#define CONFIG_MX28_FEC_MAC_IN_OCOTP
+#endif
+
+/* RTC */
+#ifdef CONFIG_CMD_DATE
+#define CONFIG_RTC_MXS
+#endif
+
+/* USB */
+#ifdef CONFIG_CMD_USB
+#define CONFIG_EHCI_MXS_PORT1
+#define CONFIG_USB_MAX_CONTROLLER_COUNT 1
+#define CONFIG_USB_STORAGE
+#define CONFIG_USB_HOST_ETHER
+#define CONFIG_USB_ETHER_ASIX
+#define CONFIG_USB_ETHER_SMSC95XX
+#endif
+
+/* SPI */
+#ifdef CONFIG_CMD_SPI
+#define CONFIG_DEFAULT_SPI_BUS 2
+#define CONFIG_DEFAULT_SPI_MODE SPI_MODE_0
+
+/* SPI Flash */
+#ifdef CONFIG_CMD_SF
+#define CONFIG_SPI_FLASH
+#define CONFIG_SF_DEFAULT_BUS 2
+#define CONFIG_SF_DEFAULT_CS 0
+/* this may vary and depends on the installed chip */
+#define CONFIG_SPI_FLASH_SST
+#define CONFIG_SF_DEFAULT_MODE SPI_MODE_0
+#define CONFIG_SF_DEFAULT_SPEED 24000000
+#endif
+
+#endif
+
+/* Framebuffer support */
+#ifdef CONFIG_VIDEO
+#define CONFIG_VIDEO_LOGO
+#define CONFIG_SPLASH_SCREEN
+#define CONFIG_CMD_BMP
+#define CONFIG_BMP_16BPP
+#define CONFIG_VIDEO_BMP_RLE8
+#define CONFIG_VIDEO_BMP_GZIP
+#define CONFIG_SYS_VIDEO_LOGO_MAX_SIZE (512 << 10)
+#endif
+
+/* Boot Linux */
+#define CONFIG_BOOTDELAY 1
+#define CONFIG_BOOTFILE "uImage"
+#define CONFIG_LOADADDR 0x42000000
+#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
+
+/* Extra Environment */
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "ubifs_file=filesystem.ubifs\0" \
+ "update_nand_full_filename=u-boot.nand\0" \
+ "update_nand_firmware_filename=u-boot.sb\0" \
+ "update_nand_firmware_maxsz=0x100000\0" \
+ "update_nand_stride=0x40\0" /* MX28 datasheet ch. 12.12 */ \
+ "update_nand_count=0x4\0" /* MX28 datasheet ch. 12.12 */ \
+ "update_nand_get_fcb_size=" /* Get size of FCB blocks */ \
+ "nand device 0 ; " \
+ "nand info ; " \
+ "setexpr fcb_sz ${update_nand_stride} * ${update_nand_count};" \
+ "setexpr update_nand_fcb ${fcb_sz} * ${nand_writesize}\0" \
+ "update_nand_firmware_full=" /* Update FCB, DBBT and FW */ \
+ "if tftp ${update_nand_full_filename} ; then " \
+ "run update_nand_get_fcb_size ; " \
+ "nand scrub -y 0x0 ${filesize} ; " \
+ "nand write.raw ${loadaddr} 0x0 ${fcb_sz} ; " \
+ "setexpr update_off ${loadaddr} + ${update_nand_fcb} ; " \
+ "setexpr update_sz ${filesize} - ${update_nand_fcb} ; " \
+ "nand write ${update_off} ${update_nand_fcb} ${update_sz} ; " \
+ "fi\0" \
+ "update_nand_firmware=" /* Update only firmware */ \
+ "if tftp ${update_nand_firmware_filename} ; then " \
+ "run update_nand_get_fcb_size ; " \
+ "setexpr fcb_sz ${update_nand_fcb} * 2 ; " /* FCB + DBBT */ \
+ "setexpr fw_sz ${update_nand_firmware_maxsz} * 2 ; " \
+ "setexpr fw_off ${fcb_sz} + ${update_nand_firmware_maxsz};" \
+ "nand erase ${fcb_sz} ${fw_sz} ; " \
+ "nand write ${loadaddr} ${fcb_sz} ${filesize} ; " \
+ "nand write ${loadaddr} ${fw_off} ${filesize} ; " \
+ "fi\0" \
+ "update_nand_kernel=" /* Update kernel */ \
+ "mtdparts default; " \
+ "nand erase.part kernel; " \
+ "if test ${ip_dyn} = yes; then " \
+ "setenv get_cmd dhcp; " \
+ "else " \
+ "setenv get_cmd tftp; " \
+ "fi; " \
+ "${get_cmd} ${image}; " \
+ "nand write ${loadaddr} kernel ${filesize}\0" \
+ "update_nand_fdt=" /* Update fdt */ \
+ "mtdparts default; " \
+ "nand erase.part fdt; " \
+ "if test ${ip_dyn} = yes; then " \
+ "setenv get_cmd dhcp; " \
+ "else " \
+ "setenv get_cmd tftp; " \
+ "fi; " \
+ "${get_cmd} ${fdt_file}; " \
+ "nand write ${loadaddr} fdt ${filesize}\0" \
+ "update_nand_filesystem=" /* Update filesystem */ \
+ "mtdparts default; " \
+ "nand erase.part filesystem; " \
+ "if test ${ip_dyn} = yes; then " \
+ "setenv get_cmd dhcp; " \
+ "else " \
+ "setenv get_cmd tftp; " \
+ "fi; " \
+ "${get_cmd} ${ubifs_file}; " \
+ "ubi part filesystem; " \
+ "ubi create filesystem; " \
+ "ubi write ${loadaddr} filesystem ${filesize}\0" \
+ "nandargs=setenv bootargs console=${console_mainline},${baudrate} " \
+ "rootfstype=ubifs ubi.mtd=6 root=ubi0_0 ${mtdparts}\0" \
+ "nandboot=" /* Boot from NAND */ \
+ "mtdparts default; " \
+ "run nandargs; " \
+ "nand read ${loadaddr} kernel 0x00400000; " \
+ "if test ${boot_fdt} = yes; then " \
+ "nand read ${fdt_addr} fdt 0x00080000; " \
+ "bootz ${loadaddr} - ${fdt_addr}; " \
+ "else " \
+ "if test ${boot_fdt} = no; then " \
+ "bootz; " \
+ "else " \
+ "echo \"ERROR: Set boot_fdt to yes or no.\"; " \
+ "fi; " \
+ "fi\0" \
+ "update_sd_firmware_filename=u-boot.sd\0" \
+ "update_sd_firmware=" /* Update the SD firmware partition */ \
+ "if mmc rescan ; then " \
+ "if tftp ${update_sd_firmware_filename} ; then " \
+ "setexpr fw_sz ${filesize} / 0x200 ; " /* SD block size */ \
+ "setexpr fw_sz ${fw_sz} + 1 ; " \
+ "mmc write ${loadaddr} 0x800 ${fw_sz} ; " \
+ "fi ; " \
+ "fi\0" \
+ "script=boot.scr\0" \
+ "image=zImage\0" \
+ "console_fsl=ttyAM0\0" \
+ "console_mainline=ttyAMA0\0" \
+ "fdt_file=imx28-evk.dtb\0" \
+ "fdt_addr=0x41000000\0" \
+ "boot_fdt=try\0" \
+ "ip_dyn=yes\0" \
+ "mmcdev=0\0" \
+ "mmcpart=2\0" \
+ "mmcroot=/dev/mmcblk0p3 rw rootwait\0" \
+ "mmcargs=setenv bootargs console=${console_mainline},${baudrate} " \
+ "root=${mmcroot}\0" \
+ "loadbootscript=" \
+ "fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
+ "bootscript=echo Running bootscript from mmc ...; " \
+ "source\0" \
+ "loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \
+ "loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \
+ "mmcboot=echo Booting from mmc ...; " \
+ "run mmcargs; " \
+ "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
+ "if run loadfdt; then " \
+ "bootz ${loadaddr} - ${fdt_addr}; " \
+ "else " \
+ "if test ${boot_fdt} = try; then " \
+ "bootz; " \
+ "else " \
+ "echo WARN: Cannot load the DT; " \
+ "fi; " \
+ "fi; " \
+ "else " \
+ "bootz; " \
+ "fi;\0" \
+ "netargs=setenv bootargs console=${console_mainline},${baudrate} " \
+ "root=/dev/nfs " \
+ "ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \
+ "netboot=echo Booting from net ...; " \
+ "run netargs; " \
+ "if test ${ip_dyn} = yes; then " \
+ "setenv get_cmd dhcp; " \
+ "else " \
+ "setenv get_cmd tftp; " \
+ "fi; " \
+ "${get_cmd} ${image}; " \
+ "if test ${boot_fdt} = yes; then " \
+ "if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \
+ "bootz ${loadaddr} - ${fdt_addr}; " \
+ "else " \
+ "if test ${boot_fdt} = try; then " \
+ "bootz; " \
+ "else " \
+ "echo WARN: Cannot load the DT; " \
+ "fi;" \
+ "fi; " \
+ "else " \
+ "bootz; " \
+ "fi;\0"
+
+#define CONFIG_BOOTCOMMAND \
+ "mmc dev ${mmcdev}; if mmc rescan; then " \
+ "if run loadbootscript; then " \
+ "run bootscript; " \
+ "else " \
+ "if run loadimage; then " \
+ "run mmcboot; " \
+ "else run netboot; " \
+ "fi; " \
+ "fi; " \
+ "else run netboot; fi"
+
+/* The rest of the configuration is shared */
+#include <configs/mxs.h>
+
+#endif /* __CONFIGS_MX28EVK_H__ */
Code Review / kvmfornfv.git / blobdiff