--- /dev/null
+/*
+ * (C) Copyright 2008
+ * Heiko Schocher, DENX Software Engineering, hs@denx.de.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+
+#define CONFIG_MUAS3001 1
+
+#define CONFIG_SYS_TEXT_BASE 0xFF000000
+
+#define CONFIG_CPM2 1 /* Has a CPM2 */
+
+/* Do boardspecific init */
+#define CONFIG_BOARD_EARLY_INIT_R 1
+
+/* enable Watchdog */
+#define CONFIG_WATCHDOG 1
+
+/*
+ * Select serial console configuration
+ *
+ * If either CONFIG_CONS_ON_SMC or CONFIG_CONS_ON_SCC is selected, then
+ * CONFIG_CONS_INDEX must be set to the channel number (1-2 for SMC, 1-4
+ * for SCC).
+ */
+#define CONFIG_CONS_ON_SMC /* Console is on SMC */
+#undef CONFIG_CONS_ON_SCC /* It's not on SCC */
+#undef CONFIG_CONS_NONE /* It's not on external UART */
+#if defined(CONFIG_MUAS_DEV_BOARD)
+#define CONFIG_CONS_INDEX 2 /* SMC2 is used for console */
+#else
+#define CONFIG_CONS_INDEX 1 /* SMC1 is used for console */
+#endif
+
+/*
+ * Select ethernet configuration
+ *
+ * If either CONFIG_ETHER_ON_SCC or CONFIG_ETHER_ON_FCC is selected,
+ * then CONFIG_ETHER_INDEX must be set to the channel number (1-4 for
+ * SCC, 1-3 for FCC)
+ *
+ * If CONFIG_ETHER_NONE is defined, then either the ethernet routines
+ * must be defined elsewhere (as for the console), or CONFIG_CMD_NET
+ * must be unset.
+ */
+#undef CONFIG_ETHER_ON_SCC /* Ethernet is not on SCC */
+#define CONFIG_ETHER_ON_FCC /* Ethernet is on FCC */
+#undef CONFIG_ETHER_NONE /* No external Ethernet */
+
+#define CONFIG_ETHER_INDEX 1
+#define CONFIG_ETHER_ON_FCC1
+#define CONFIG_HAS_ETH0
+#define FCC_ENET
+
+/*
+ * - Rx-CLK is CLK11
+ * - Tx-CLK is CLK12
+ */
+# define CONFIG_SYS_CMXFCR_VALUE1 (CMXFCR_RF1CS_CLK11 | CMXFCR_TF1CS_CLK12)
+# define CONFIG_SYS_CMXFCR_MASK1 (CMXFCR_FC1 | CMXFCR_RF1CS_MSK | CMXFCR_TF1CS_MSK)
+/*
+ * - RAM for BD/Buffers is on the 60x Bus (see 28-13)
+ */
+# define CONFIG_SYS_CPMFCR_RAMTYPE (0)
+/* know on local Bus */
+/* define CONFIG_SYS_CPMFCR_RAMTYPE (CPMFCR_DTB | CPMFCR_BDB) */
+/*
+ * - Enable Full Duplex in FSMR
+ */
+# define CONFIG_SYS_FCC_PSMR (FCC_PSMR_FDE|FCC_PSMR_LPB)
+
+#define CONFIG_MII /* MII PHY management */
+#define CONFIG_BITBANGMII /* bit-bang MII PHY management */
+# define CONFIG_SYS_PHY_ADDR 1
+/*
+ * GPIO pins used for bit-banged MII communications
+ */
+#define MDIO_PORT 0 /* Port A */
+#define MDIO_DECLARE volatile ioport_t *iop = ioport_addr ( \
+ (immap_t *) CONFIG_SYS_IMMR, MDIO_PORT )
+#define MDC_DECLARE MDIO_DECLARE
+
+
+#define CONFIG_SYS_MDIO_PIN 0x00200000 /* PA10 */
+#define CONFIG_SYS_MDC_PIN 0x00400000 /* PA9 */
+
+#define MDIO_ACTIVE (iop->pdir |= CONFIG_SYS_MDIO_PIN)
+#define MDIO_TRISTATE (iop->pdir &= ~CONFIG_SYS_MDIO_PIN)
+#define MDIO_READ ((iop->pdat & CONFIG_SYS_MDIO_PIN) != 0)
+
+#define MDIO(bit) if(bit) iop->pdat |= CONFIG_SYS_MDIO_PIN; \
+ else iop->pdat &= ~CONFIG_SYS_MDIO_PIN
+
+#define MDC(bit) if(bit) iop->pdat |= CONFIG_SYS_MDC_PIN; \
+ else iop->pdat &= ~CONFIG_SYS_MDC_PIN
+
+#define MIIDELAY udelay(1)
+
+#ifndef CONFIG_8260_CLKIN
+#define CONFIG_8260_CLKIN 66000000 /* in Hz */
+#endif
+
+#define CONFIG_BAUDRATE 115200
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_DTT
+#define CONFIG_CMD_ECHO
+#define CONFIG_CMD_IMMAP
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_I2C
+
+/*
+ * Default environment settings
+ */
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "netdev=eth0\0" \
+ "u-boot_addr_r=100000\0" \
+ "kernel_addr_r=200000\0" \
+ "fdt_addr_r=400000\0" \
+ "rootpath=/opt/eldk/ppc_6xx\0" \
+ "u-boot=muas3001/u-boot.bin\0" \
+ "bootfile=muas3001/uImage\0" \
+ "fdt_file=muas3001/muas3001.dtb\0" \
+ "ramdisk_file=uRamdisk\0" \
+ "load=tftp ${u-boot_addr_r} ${u-boot}\0" \
+ "update=prot off ff000000 ff03ffff; era ff000000 ff03ffff; " \
+ "cp.b ${u-boot_addr_r} ff000000 ${filesize};" \
+ "prot on ff000000 ff03ffff\0" \
+ "ramargs=setenv bootargs root=/dev/ram rw\0" \
+ "nfsargs=setenv bootargs root=/dev/nfs rw " \
+ "nfsroot=${serverip}:${rootpath}\0" \
+ "addcons=setenv bootargs ${bootargs} console=ttyCPM0,${baudrate}\0" \
+ "addmtd=setenv bootargs ${bootargs} ${mtdparts}\0" \
+ "addip=setenv bootargs ${bootargs} " \
+ "ip=${ipaddr}:${serverip}:${gatewayip}:" \
+ "${netmask}:${hostname}:${netdev}:off panic=1\0" \
+ "net_nfs=tftp ${kernel_addr_r} ${bootfile}; " \
+ "tftp ${fdt_addr_r} ${fdt_file}; run nfsargs addip addcons;" \
+ "bootm ${kernel_addr_r} - ${fdt_addr_r}\0" \
+ "net_self=tftp ${kernel_addr_r} ${bootfile}; " \
+ "tftp ${fdt_addr_r} ${fdt_file}; " \
+ "tftp ${ramdisk_addr} ${ramdisk_file}; " \
+ "run ramargs addip; " \
+ "bootm ${kernel_addr_r} ${ramdisk_addr} ${fdt_addr_r}\0" \
+ "ramdisk_addr=ff210000\0" \
+ "kernel_addr=ff050000\0" \
+ "fdt_addr=ff200000\0" \
+ "flash_self=run ramargs addip addcons;bootm ${kernel_addr}" \
+ " ${ramdisk_addr} ${fdt_addr}\0" \
+ "updateramdisk=era ${ramdisk_addr} +1f0000;tftpb ${kernel_addr_r}" \
+ " ${ramdisk_file};" \
+ "cp.b ${kernel_addr_r} ${ramdisk_addr} ${filesize}\0" \
+ "updatekernel=era ${kernel_addr} +1b0000;tftpb ${kernel_addr_r}" \
+ " ${bootfile};" \
+ "cp.b ${kernel_addr_r} ${kernel_addr} ${filesize}\0" \
+ "updatefdt=era ${fdt_addr} +10000;tftpb ${fdt_addr_r} ${fdt_file};" \
+ "cp.b ${fdt_addr_r} ${fdt_addr} ${filesize}\0" \
+ ""
+
+#define CONFIG_BOOTCOMMAND "run net_nfs"
+#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#if defined(CONFIG_CMD_KGDB)
+#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
+#else
+#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
+#endif
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
+
+#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */
+#define CONFIG_SYS_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */
+
+#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
+
+#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 }
+
+#define CONFIG_SYS_SDRAM_BASE 0x00000000
+#define CONFIG_SYS_FLASH_BASE 0xFF000000
+#define CONFIG_SYS_FLASH_SIZE 32
+#define CONFIG_SYS_FLASH_CFI
+#define CONFIG_FLASH_CFI_DRIVER
+#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of flash banks */
+#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max num of sects on one chip */
+
+#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE }
+
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
+#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
+#define CONFIG_SYS_RAMBOOT
+#endif
+
+#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256KB for Monitor */
+
+#define CONFIG_ENV_IS_IN_FLASH
+
+#ifdef CONFIG_ENV_IS_IN_FLASH
+#define CONFIG_ENV_SECT_SIZE 0x10000
+#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
+#endif /* CONFIG_ENV_IS_IN_FLASH */
+
+/*
+ * I2C Bus
+ */
+#define CONFIG_HARD_I2C 1 /* To enable I2C support */
+#define CONFIG_SYS_I2C_SPEED 100000 /* I2C speed and slave address */
+#define CONFIG_SYS_I2C_SLAVE 0x7F
+
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
+/* I2C SYSMON (LM75, AD7414 is almost compatible) */
+#define CONFIG_DTT_LM75 1 /* ON Semi's LM75 */
+#define CONFIG_DTT_SENSORS {0} /* Sensor addresses */
+#define CONFIG_SYS_DTT_MAX_TEMP 70
+#define CONFIG_SYS_DTT_LOW_TEMP -30
+#define CONFIG_SYS_DTT_HYSTERESIS 3
+
+#define CONFIG_SYS_IMMR 0xF0000000
+#define CONFIG_SYS_DEFAULT_IMMR 0x0F010000
+
+#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR
+#define CONFIG_SYS_INIT_RAM_SIZE 0x2000 /* Size of used area in DPRAM */
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
+
+/* Hard reset configuration word */
+#define CONFIG_SYS_HRCW_MASTER 0x0E028200 /* BPS=11 CIP=1 ISB=010 BMS=1 */
+
+/* No slaves */
+#define CONFIG_SYS_HRCW_SLAVE1 0
+#define CONFIG_SYS_HRCW_SLAVE2 0
+#define CONFIG_SYS_HRCW_SLAVE3 0
+#define CONFIG_SYS_HRCW_SLAVE4 0
+#define CONFIG_SYS_HRCW_SLAVE5 0
+#define CONFIG_SYS_HRCW_SLAVE6 0
+#define CONFIG_SYS_HRCW_SLAVE7 0
+
+#define CONFIG_SYS_MALLOC_LEN (4096 << 10) /* Reserve 4 MB for malloc() */
+#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+
+#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC8260 CPUs */
+#if defined(CONFIG_CMD_KGDB)
+# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */
+#endif
+
+#define CONFIG_SYS_HID0_INIT 0
+#define CONFIG_SYS_HID0_FINAL (HID0_ICE | HID0_IFEM | HID0_ABE)
+
+#define CONFIG_SYS_HID2 0
+
+#define CONFIG_SYS_SIUMCR 0x00200000
+#define CONFIG_SYS_BCR 0x004c0000
+#define CONFIG_SYS_SCCR 0x0
+
+/*-----------------------------------------------------------------------
+ * SYPCR - System Protection Control 4-35
+ * SYPCR can only be written once after reset!
+ *-----------------------------------------------------------------------
+ * Watchdog & Bus Monitor Timer max, 60x Bus Monitor enable
+ */
+#if defined(CONFIG_WATCHDOG)
+#define CONFIG_SYS_SYPCR (SYPCR_SWTC|SYPCR_BMT|SYPCR_PBME|SYPCR_LBME|\
+ SYPCR_SWRI|SYPCR_SWP|SYPCR_SWE)
+#else
+#define CONFIG_SYS_SYPCR (SYPCR_SWTC|SYPCR_BMT|SYPCR_PBME|SYPCR_LBME|\
+ SYPCR_SWRI|SYPCR_SWP)
+#endif /* CONFIG_WATCHDOG */
+
+/*-----------------------------------------------------------------------
+ * RMR - Reset Mode Register 5-5
+ *-----------------------------------------------------------------------
+ * turn on Checkstop Reset Enable
+ */
+#define CONFIG_SYS_RMR 0
+
+/*-----------------------------------------------------------------------
+ * TMCNTSC - Time Counter Status and Control 4-40
+ *-----------------------------------------------------------------------
+ * Clear once per Second and Alarm Interrupt Status, Set 32KHz timersclk,
+ * and enable Time Counter
+ */
+#define CONFIG_SYS_TMCNTSC (TMCNTSC_SEC|TMCNTSC_ALR|TMCNTSC_TCF|TMCNTSC_TCE)
+
+/*-----------------------------------------------------------------------
+ * PISCR - Periodic Interrupt Status and Control 4-42
+ *-----------------------------------------------------------------------
+ * Clear Periodic Interrupt Status, Set 32KHz timersclk, and enable
+ * Periodic timer
+ */
+#define CONFIG_SYS_PISCR (PISCR_PS|PISCR_PTF|PISCR_PTE)
+
+/*-----------------------------------------------------------------------
+ * RCCR - RISC Controller Configuration 13-7
+ *-----------------------------------------------------------------------
+ */
+#define CONFIG_SYS_RCCR 0
+
+/*
+ * Init Memory Controller:
+ *
+ * Bank Bus Machine PortSz Device
+ * ---- --- ------- ------ ------
+ * 0 60x GPCM 32 bit FLASH
+ * 1 60x SDRAM 64 bit SDRAM
+ * 4 60x GPCM 16 bit I/O Ctrl
+ *
+ */
+/* Bank 0 - FLASH
+ */
+#define CONFIG_SYS_BR0_PRELIM ((CONFIG_SYS_FLASH_BASE & BRx_BA_MSK) |\
+ BRx_PS_32 |\
+ BRx_MS_GPCM_P |\
+ BRx_V)
+
+#define CONFIG_SYS_OR0_PRELIM (0xff000020)
+
+/* Bank 1 - 60x bus SDRAM
+ */
+#define CONFIG_SYS_GLOBAL_SDRAM_LIMIT (256 << 20) /* less than 256 MB */
+
+#define CONFIG_SYS_MPTPR 0x2800
+
+/*-----------------------------------------------------------------------------
+ * Address for Mode Register Set (MRS) command
+ *-----------------------------------------------------------------------------
+ */
+#define CONFIG_SYS_MRS_OFFS 0x00000110
+#define CONFIG_SYS_PSRT 0x13
+
+#define CONFIG_SYS_BR1_PRELIM ((CONFIG_SYS_SDRAM_BASE & BRx_BA_MSK) |\
+ BRx_PS_64 |\
+ BRx_MS_SDRAM_P |\
+ BRx_V)
+
+#define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_OR1_LITTLE
+
+/* SDRAM initialization values
+*/
+#define CONFIG_SYS_OR1_LITTLE ((~(CONFIG_SYS_GLOBAL_SDRAM_LIMIT-1) & ORxS_SDAM_MSK) |\
+ ORxS_BPD_4 |\
+ ORxS_ROWST_PBI1_A7 |\
+ ORxS_NUMR_12)
+
+#define CONFIG_SYS_PSDMR_LITTLE 0x004b36a3
+
+#define CONFIG_SYS_OR1_BIG ((~(CONFIG_SYS_GLOBAL_SDRAM_LIMIT-1) & ORxS_SDAM_MSK) |\
+ ORxS_BPD_4 |\
+ ORxS_ROWST_PBI1_A4 |\
+ ORxS_NUMR_12)
+
+#define CONFIG_SYS_PSDMR_BIG 0x014f36a3
+
+/* IO on CS4 initialization values
+*/
+#define CONFIG_SYS_IO_BASE 0xc0000000
+#define CONFIG_SYS_IO_SIZE 1
+
+#define CONFIG_SYS_BR4_PRELIM ((CONFIG_SYS_IO_BASE & BRx_BA_MSK) |\
+ BRx_PS_16 | BRx_MS_GPCM_L | BRx_V)
+
+#define CONFIG_SYS_OR4_PRELIM (0xfff80020)
+
+#define CONFIG_SYS_RESET_ADDRESS 0xFDFFFFFC /* "bad" address */
+
+/* pass open firmware flat tree */
+#define CONFIG_OF_LIBFDT 1
+#define CONFIG_OF_BOARD_SETUP 1
+
+#define OF_TBCLK (bd->bi_busfreq / 4)
+#if defined(CONFIG_MUAS_DEV_BOARD)
+#define OF_STDOUT_PATH "/soc/cpm/serial@11a90"
+#else
+#define OF_STDOUT_PATH "/soc/cpm/serial@11a80"
+#endif
+
+#endif /* __CONFIG_H */
Code Review / kvmfornfv.git / blobdiff