--- /dev/null
+/*
+ * (C) Copyright 2009
+ * Heiko Schocher, DENX Software Engineering, hs@denx.de.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __MANROLAND_MPC52XX__COMMON_H
+#define __MANROLAND_MPC52XX__COMMON_H
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+#define CONFIG_MPC5200 1 /* MPC5200 CPU */
+
+#define CONFIG_SYS_MPC5XXX_CLKIN 33000000 /* ... running at 33.000000MHz */
+
+#define CONFIG_HIGH_BATS 1 /* High BATs supported */
+
+/*
+ * Serial console configuration
+ */
+#define CONFIG_PSC_CONSOLE 1 /* console is on PSC1 */
+#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200,\
+ 230400 }
+
+#if (CONFIG_SYS_TEXT_BASE == 0xFFF00000) /* Boot low */
+# define CONFIG_SYS_LOWBOOT 1
+#endif
+
+/*
+ * IPB Bus clocking configuration.
+ */
+#define CONFIG_SYS_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */
+
+/*
+ * I2C configuration
+ */
+#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
+#define CONFIG_SYS_I2C_MODULE 2 /* Select I2C module #1 or #2 */
+
+#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */
+#define CONFIG_SYS_I2C_SLAVE 0x7F
+
+/*
+ * EEPROM configuration
+ */
+#define CONFIG_SYS_I2C_EEPROM_ADDR 0x58
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10
+
+/*
+ * RTC configuration
+ */
+#define CONFIG_RTC_PCF8563
+#define CONFIG_SYS_I2C_RTC_ADDR 0x51
+
+/* I2C SYSMON (LM75) */
+#define CONFIG_DTT_LM81 1 /* ON Semi's LM75 */
+#define CONFIG_DTT_SENSORS {0} /* Sensor addresses */
+#define CONFIG_SYS_DTT_MAX_TEMP 70
+#define CONFIG_SYS_DTT_LOW_TEMP -30
+#define CONFIG_SYS_DTT_HYSTERESIS 3
+
+/*
+ * Flash configuration
+ */
+#define CONFIG_SYS_FLASH_BASE 0xFF800000
+
+#define CONFIG_SYS_FLASH_SIZE 0x00800000 /* 8 MByte */
+
+#define CONFIG_ENV_ADDR (CONFIG_SYS_TEXT_BASE+0x40000) /* second sector */
+#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of flash banks
+ (= chip selects) */
+#define CONFIG_SYS_FLASH_ERASE_TOUT 240000 /* Flash Erase Timeout [ms]*/
+#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout [ms]*/
+
+#define CONFIG_FLASH_CFI_DRIVER
+#define CONFIG_SYS_FLASH_CFI
+#define CONFIG_SYS_FLASH_EMPTY_INFO
+#define CONFIG_SYS_FLASH_CFI_AMD_RESET
+
+/*
+ * Environment settings
+ */
+#define CONFIG_ENV_IS_IN_FLASH 1
+#define CONFIG_ENV_SIZE 0x4000
+#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET+CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
+
+/*
+ * Memory map
+ */
+#define CONFIG_SYS_MBAR 0xF0000000
+#define CONFIG_SYS_DEFAULT_MBAR 0x80000000
+
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE -\
+ GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
+
+#define CONFIG_SYS_SDRAM_BASE 0x00000000
+#define CONFIG_SYS_SRAM_BASE 0x80100000 /* CS 1 */
+#define CONFIG_SYS_DISPLAY_BASE 0x80600000 /* CS 3 */
+
+/* Settings for XLB = 132 MHz */
+#define SDRAM_DDR 1
+#define SDRAM_MODE 0x018D0000
+#define SDRAM_EMODE 0x40090000
+#define SDRAM_CONTROL 0x714f0f00
+#define SDRAM_CONFIG1 0x73722930
+#define SDRAM_CONFIG2 0x47770000
+#define SDRAM_TAPDELAY 0x10000000
+
+/* Use ON-Chip SRAM until RAM will be available */
+#define CONFIG_SYS_INIT_RAM_ADDR MPC5XXX_SRAM
+#ifdef CONFIG_POST
+/* preserve space for the post_word at end of on-chip SRAM */
+#define CONFIG_SYS_INIT_RAM_SIZE MPC5XXX_SRAM_POST_SIZE
+#else
+#define CONFIG_SYS_INIT_RAM_SIZE MPC5XXX_SRAM_SIZE
+#endif
+
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
+#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
+# define CONFIG_SYS_RAMBOOT 1
+#endif
+
+#define CONFIG_SYS_MONITOR_LEN (192 << 10)
+#define CONFIG_SYS_MALLOC_LEN (512 << 10)
+#define CONFIG_SYS_BOOTMAPSZ (8 << 20)
+
+/*
+ * Ethernet configuration
+ */
+#define CONFIG_MPC5xxx_FEC 1
+#define CONFIG_MPC5xxx_FEC_MII100
+#define CONFIG_PHY_ADDR 0x00
+#define CONFIG_MII 1
+
+/*use Hardware WDT */
+#define CONFIG_HW_WATCHDOG
+
+#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */
+#if defined(CONFIG_CMD_KGDB)
+# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value*/
+#endif
+
+/*
+ * Various low-level settings
+ */
+#define CONFIG_SYS_HID0_INIT HID0_ICE | HID0_ICFI
+#define CONFIG_SYS_HID0_FINAL HID0_ICE
+
+#define CONFIG_SYS_BOOTCS_START CONFIG_SYS_FLASH_BASE
+#define CONFIG_SYS_BOOTCS_SIZE CONFIG_SYS_FLASH_SIZE
+#define CONFIG_SYS_CS0_START CONFIG_SYS_FLASH_BASE
+#define CONFIG_SYS_CS0_SIZE CONFIG_SYS_FLASH_SIZE
+
+/* 8Mbit SRAM @0x80100000 */
+#define CONFIG_SYS_CS1_START CONFIG_SYS_SRAM_BASE
+
+#define CONFIG_SYS_CS_BURST 0x00000000
+#define CONFIG_SYS_CS_DEADCYCLE 0x33333333
+
+/*-----------------------------------------------------------------------
+ * IDE/ATA stuff Supports IDE harddisk
+ *-----------------------------------------------------------------------
+ */
+
+#undef CONFIG_IDE_8xx_PCCARD /* Use IDE with PC Card Adapter */
+
+#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */
+#undef CONFIG_IDE_LED /* LED for ide not supported */
+
+#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */
+
+#define CONFIG_IDE_PREINIT 1
+
+#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000
+
+#define CONFIG_SYS_ATA_BASE_ADDR MPC5XXX_ATA
+
+/* Offset for data I/O */
+#define CONFIG_SYS_ATA_DATA_OFFSET (0x0060)
+
+/* Offset for normal register accesses */
+#define CONFIG_SYS_ATA_REG_OFFSET (CONFIG_SYS_ATA_DATA_OFFSET)
+
+/* Offset for alternate registers */
+#define CONFIG_SYS_ATA_ALT_OFFSET (0x005C)
+
+/* Interval between registers */
+#define CONFIG_SYS_ATA_STRIDE 4
+
+#define CONFIG_ATAPI 1
+
+#define OF_CPU "PowerPC,5200@0"
+#define OF_SOC "soc5200@f0000000"
+#define OF_TBCLK (bd->bi_busfreq / 4)
+#define OF_STDOUT_PATH "/soc5200@f0000000/serial@2000"
+#define CONFIG_OF_IDE_FIXUP
+
+#endif /* __MANROLAND_MPC52XX__COMMON_H */
Code Review / kvmfornfv.git / blobdiff