--- /dev/null
+/*
+ * (C) Copyright 2007
+ * Heiko Schocher, DENX Software Engineering, hs@denx.de.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+
+#define CONFIG_MPC5200 1 /* This is an MPC5200 CPU */
+#define CONFIG_JUPITER 1 /* ... on Jupiter board */
+
+/*
+ * Valid values for CONFIG_SYS_TEXT_BASE are:
+ * 0xFFF00000 boot high (standard configuration)
+ * 0x00100000 boot from RAM (for testing only)
+ */
+#ifndef CONFIG_SYS_TEXT_BASE
+#define CONFIG_SYS_TEXT_BASE 0xFFF00000
+#endif
+
+#define CONFIG_SYS_MPC5XXX_CLKIN 33000000 /* ... running at 33.000000MHz */
+
+#define CONFIG_BOARD_EARLY_INIT_R 1
+#define CONFIG_BOARD_EARLY_INIT_F 1
+
+#define CONFIG_HIGH_BATS 1 /* High BATs supported */
+
+/*
+ * Serial console configuration
+ */
+#define CONFIG_PSC_CONSOLE 1 /* console is on PSC1 */
+#define CONFIG_BAUDRATE 115200 /* ... at 115200 bps */
+#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 }
+
+/*
+ * PCI Mapping:
+ * 0x40000000 - 0x4fffffff - PCI Memory
+ * 0x50000000 - 0x50ffffff - PCI IO Space
+ */
+/*#define CONFIG_PCI */
+
+#if defined(CONFIG_PCI)
+#define CONFIG_PCI_PNP 1
+#define CONFIG_PCI_SCAN_SHOW 1
+#define CONFIG_PCIAUTO_SKIP_HOST_BRIDGE 1
+
+#define CONFIG_PCI_MEM_BUS 0x40000000
+#define CONFIG_PCI_MEM_PHYS CONFIG_PCI_MEM_BUS
+#define CONFIG_PCI_MEM_SIZE 0x10000000
+
+#define CONFIG_PCI_IO_BUS 0x50000000
+#define CONFIG_PCI_IO_PHYS CONFIG_PCI_IO_BUS
+#define CONFIG_PCI_IO_SIZE 0x01000000
+#endif
+
+#define CONFIG_SYS_XLB_PIPELINING 1
+
+#define CONFIG_MII 1
+#define CONFIG_SYS_RX_ETH_BUFFER 8 /* use 8 rx buffer on eepro100 */
+
+/* Partitions */
+#define CONFIG_MAC_PARTITION
+#define CONFIG_DOS_PARTITION
+#define CONFIG_ISO_PARTITION
+
+#define CONFIG_TIMESTAMP /* Print image info with timestamp */
+
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_NFS
+#define CONFIG_CMD_SNTP
+
+#if defined(CONFIG_PCI)
+#define CODFIG_CMD_PCI
+#endif
+
+
+/*
+ * Autobooting
+ */
+#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
+
+#define CONFIG_PREBOOT "echo;" \
+ "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
+ "echo"
+
+#undef CONFIG_BOOTARGS
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "netdev=eth0\0" \
+ "nfsargs=setenv bootargs root=/dev/nfs rw " \
+ "nfsroot=${serverip}:${rootpath}\0" \
+ "ramargs=setenv bootargs root=/dev/ram rw\0" \
+ "addip=setenv bootargs ${bootargs} " \
+ "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
+ ":${hostname}:${netdev}:off panic=1\0" \
+ "flash_nfs=run nfsargs addip addcons;" \
+ "bootm ${kernel_addr}\0" \
+ "flash_self=run ramargs addip;" \
+ "bootm ${kernel_addr} ${ramdisk_addr}\0" \
+ "addcons=setenv bootargs ${bootargs} console=${contyp}," \
+ "${baudrate}\0" \
+ "contyp=ttyS0\0" \
+ "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addcons;" \
+ "bootm\0" \
+ "rootpath=/opt/eldk/ppc_6xx\0" \
+ "bootfile=/tftpboot/jupiter/uImage\0" \
+ ""
+
+#define CONFIG_BOOTCOMMAND "run flash_self"
+
+/*
+ * IPB Bus clocking configuration.
+ */
+#undef CONFIG_SYS_IPBSPEED_133 /* define for 133MHz speed */
+
+#if 0
+/* pass open firmware flat tree */
+#define CONFIG_OF_LIBFDT 1
+#define CONFIG_OF_BOARD_SETUP 1
+
+#define OF_CPU "PowerPC,5200@0"
+#define OF_SOC "soc5200@f0000000"
+#define OF_TBCLK (bd->bi_busfreq / 8)
+#define OF_STDOUT_PATH "/soc5200@f0000000/serial@2000"
+#endif
+
+#if 0
+/*
+ * I2C configuration
+ */
+#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
+#define CONFIG_SYS_I2C_MODULE 2 /* Select I2C module #1 or #2 */
+
+#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */
+#define CONFIG_SYS_I2C_SLAVE 0x7F
+
+/*
+ * EEPROM configuration
+ */
+#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* 1010000x */
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 70
+#endif
+
+/*
+ * Flash configuration
+ */
+#define CONFIG_SYS_FLASH_BASE 0xFF000000
+#define CONFIG_SYS_FLASH_SIZE 0x01000000
+
+#define CONFIG_SYS_MAX_FLASH_SECT 128 /* max num of sects on one chip */
+
+#define CONFIG_ENV_ADDR (CONFIG_SYS_TEXT_BASE + 0x40000) /* third sector */
+
+#define CONFIG_SYS_FLASH_ERASE_TOUT 240000 /* Flash Erase Timeout (in ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (in ms) */
+
+#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of flash banks */
+
+#define CONFIG_FLASH_CFI_DRIVER
+#define CONFIG_SYS_FLASH_CFI
+#define CONFIG_SYS_FLASH_EMPTY_INFO
+#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_8BIT
+#define CONFIG_SYS_UPDATE_FLASH_SIZE 1
+#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1
+
+/*
+ * Environment settings
+ */
+#define CONFIG_ENV_IS_IN_FLASH 1
+#define CONFIG_ENV_SIZE 0x20000
+#define CONFIG_ENV_SECT_SIZE 0x20000
+#define CONFIG_ENV_OVERWRITE 1
+
+/* Address and size of Redundant Environment Sector */
+#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
+
+/*
+ * Memory map
+ */
+#define CONFIG_SYS_MBAR 0xF0000000
+#define CONFIG_SYS_SDRAM_BASE 0x00000000
+#define CONFIG_SYS_DEFAULT_MBAR 0x80000000
+
+/* Use SRAM until RAM will be available */
+#define CONFIG_SYS_INIT_RAM_ADDR MPC5XXX_SRAM
+#define CONFIG_SYS_INIT_RAM_SIZE MPC5XXX_SRAM_SIZE /* Size of used area in DPRAM */
+
+
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
+
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
+#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
+# define CONFIG_SYS_RAMBOOT 1
+#endif
+
+#define CONFIG_SYS_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */
+#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
+#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+
+/*
+ * Ethernet configuration
+ */
+#define CONFIG_MPC5xxx_FEC 1
+#define CONFIG_MPC5xxx_FEC_MII100
+/*
+ * Define CONFIG_MPC5xxx_FEC_MII10 to force FEC at 10Mb
+ */
+/* #define CONFIG_MPC5xxx_FEC_MII10 */
+#define CONFIG_PHY_ADDR 0x00
+
+/*
+ * GPIO configuration
+ */
+#define CONFIG_SYS_GPS_PORT_CONFIG 0x10000004
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+
+#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
+#define CONFIG_SYS_HUSH_PARSER 1 /* Use the HUSH parser */
+#if defined(CONFIG_CMD_KGDB)
+#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
+#else
+#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
+#endif
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
+
+#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */
+#define CONFIG_SYS_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */
+#define CONFIG_SYS_ALT_MEMTEST 1
+
+#define CONFIG_SYS_LOAD_ADDR 0x200000 /* default load address */
+
+#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */
+#if defined(CONFIG_CMD_KGDB)
+# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */
+#endif
+
+/*
+ * Various low-level settings
+ */
+#define CONFIG_SYS_HID0_INIT HID0_ICE | HID0_ICFI
+#define CONFIG_SYS_HID0_FINAL HID0_ICE
+
+#define CONFIG_SYS_BOOTCS_START CONFIG_SYS_FLASH_BASE
+#define CONFIG_SYS_BOOTCS_SIZE CONFIG_SYS_FLASH_SIZE
+#define CONFIG_SYS_BOOTCS_CFG 0x00047801
+#define CONFIG_SYS_CS0_START CONFIG_SYS_FLASH_BASE
+#define CONFIG_SYS_CS0_SIZE CONFIG_SYS_FLASH_SIZE
+
+#define CONFIG_SYS_CS_BURST 0x00000000
+#define CONFIG_SYS_CS_DEADCYCLE 0x33333333
+
+#define CONFIG_SYS_RESET_ADDRESS 0xff000000
+
+#endif /* __CONFIG_H */
Code Review / kvmfornfv.git / blobdiff