--- /dev/null
+/*
+ * (C) Copyright 2003-2005
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * (C) Copyright 2006
+ * Eric Schumann, Phytec Messatechnik GmbH
+ *
+ * (C) Copyright 2009
+ * Jon Smirl <jonsmirl@gmail.com>
+ *
+ * (C) Copyright 2009
+ * Eric Millbrandt, DEKA Research and Development Corporation
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#define CONFIG_BOARDINFO "galaxy5200"
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+#define CONFIG_MPC5200 1 /* This is an MPC5200 CPU */
+#define CONFIG_SYS_MPC5XXX_CLKIN 33333333 /* ... running at 33.333333MHz */
+
+/*
+ * Valid values for CONFIG_SYS_TEXT_BASE are:
+ * 0xFFF00000 boot high (standard configuration)
+ * 0xFE000000 boot low
+ * 0x00100000 boot from RAM (for testing only) does not work
+ */
+#ifdef CONFIG_galaxy5200_LOWBOOT
+#define CONFIG_SYS_TEXT_BASE 0xFE000000
+#endif
+
+#ifndef CONFIG_SYS_TEXT_BASE
+#define CONFIG_SYS_TEXT_BASE 0xFFF00000 /* Standard: boot high */
+#endif
+
+/*
+ * Serial console configuration
+ */
+#define CONFIG_PSC_CONSOLE 4 /* console is on PSC4 -> */
+ /* define gps port conf. */
+ /* register later on to */
+ /* enable UART function! */
+#define CONFIG_BAUDRATE 115200 /* ... at 115200 bps */
+#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 }
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_DATE
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_EEPROM
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_JFFS2
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_NFS
+#define CONFIG_CMD_SNTP
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_ASKENV
+#define CONFIG_CMD_USB
+#define CONFIG_CMD_CACHE
+#define CONFIG_CMD_FAT
+
+#define CONFIG_TIMESTAMP 1 /* Print image info with timestamp */
+
+#if (CONFIG_SYS_TEXT_BASE == 0xFE000000) /* Boot low */
+#define CONFIG_SYS_LOWBOOT 1
+#endif
+/* RAMBOOT will be defined automatically in memory section */
+
+#define MTDIDS_DEFAULT "nor0=physmap-flash.0"
+#define MTDPARTS_DEFAULT "mtdparts=physmap-flash.0:256k(ubootl)," \
+ "1792k(kernel),13312k(jffs2),256k(uboot)ro,256k(oftree),-(space)"
+
+/*
+ * Autobooting
+ */
+#define CONFIG_BOOTDELAY 10 /* autoboot after 10 seconds */
+#define CONFIG_ZERO_BOOTDELAY_CHECK /* allow stopping of boot process */
+ /* even with bootdelay=0 */
+#define CONFIG_BOOT_RETRY_TIME 120 /* Reset if no command is entered */
+#define CONFIG_RESET_TO_RETRY
+
+#define CONFIG_PREBOOT "echo;" \
+ "echo Welcome to U-Boot;"\
+ "echo"
+
+#define CONFIG_BOOTCOMMAND "go ff300004 0; go ff300004 2 2;" \
+ "bootm ff040000 ff900000 fffc0000"
+#define CONFIG_BOOTARGS "console=ttyPSC0,115200"
+#define CONFIG_EXTRA_ENV_SETTINGS "epson=yes\0"
+
+/*
+ * IPB Bus clocking configuration.
+ */
+#define CONFIG_SYS_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */
+#define CONFIG_SYS_XLB_PIPELINING 1
+
+/*
+ * I2C configuration
+ */
+#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
+#define CONFIG_SYS_I2C_MODULE 2 /* Select I2C module #1 or #2 */
+#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */
+#define CONFIG_SYS_I2C_SLAVE 0x7F
+#define CONFIG_SYS_I2C_INIT_MPC5XXX /* Reset devices on i2c bus */
+
+/*
+ * EEPROM CAT24WC32 configuration
+ */
+#define CONFIG_SYS_I2C_EEPROM_ADDR 0x52 /* 1010100x */
+#define CONFIG_SYS_I2C_FACT_ADDR 0x52 /* EEPROM CAT24WC32 */
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 /* Bytes of address */
+#define CONFIG_SYS_EEPROM_SIZE 4096
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 15
+
+/*
+ * RTC configuration
+ */
+#define RTC
+#define CONFIG_RTC_DS3231 1
+#define CONFIG_SYS_I2C_RTC_ADDR 0x68
+
+/*
+ * Flash configuration
+ */
+
+#define CONFIG_SYS_FLASH_BASE 0xfe000000
+/*
+ * The flash size is autoconfigured, but arch/powerpc/cpu/mpc5xxx/cpu_init.c needs this
+ * variable defined
+ */
+#define CONFIG_SYS_FLASH_SIZE 0x02000000
+#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE }
+
+#define CONFIG_SYS_FLASH_CFI 1 /* Flash is CFI conformant */
+#define CONFIG_FLASH_CFI_DRIVER 1 /* Use the common driver */
+#define CONFIG_SYS_FLASH_EMPTY_INFO
+#define CONFIG_SYS_MAX_FLASH_SECT 259 /* max num of sects on one chip */
+#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of flash banks */
+ /* (= chip selects) */
+#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
+
+/*
+ * Use hardware protection. This seems required, as the BDI uses hardware
+ * protection. Without this, U-Boot can't work with this sectors as its
+ * protection is software only by default.
+ */
+#define CONFIG_SYS_FLASH_PROTECTION 1
+
+/*
+ * Environment settings
+ */
+
+#define CONFIG_ENV_IS_IN_EEPROM 1
+#define CONFIG_ENV_OFFSET 0x00 /* environment starts at the */
+ /* beginning of the EEPROM */
+#define CONFIG_ENV_SIZE CONFIG_SYS_EEPROM_SIZE
+
+#define CONFIG_ENV_OVERWRITE 1
+
+/*
+ * SDRAM configuration
+ */
+#define SDRAM_DDR 1
+#define SDRAM_MODE 0x018D0000
+#define SDRAM_EMODE 0x40090000
+#define SDRAM_CONTROL 0x71500F00
+#define SDRAM_CONFIG1 0x73711930
+#define SDRAM_CONFIG2 0x47770000
+
+/*
+ * Memory map
+ */
+#define CONFIG_SYS_MBAR 0xF0000000 /* MBAR has to be switched by other */
+ /* bootloader or debugger config */
+#define CONFIG_SYS_SDRAM_BASE 0x00000000
+#define CONFIG_SYS_DEFAULT_MBAR 0x80000000
+
+/* Use SRAM until RAM will be available */
+#define CONFIG_SYS_INIT_RAM_ADDR MPC5XXX_SRAM
+
+/* End of used area in SPRAM */
+#define CONFIG_SYS_INIT_RAM_SIZE MPC5XXX_SRAM_SIZE
+
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \
+ GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
+
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
+#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
+# define CONFIG_SYS_RAMBOOT 1
+#endif
+
+#define CONFIG_SYS_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */
+#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
+#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+
+/* Chip Select configuration for NAND flash */
+#define CONFIG_SYS_CS1_START 0x20000000
+#define CONFIG_SYS_CS1_SIZE 0x90000
+#define CONFIG_SYS_CS1_CFG 0x00025b00
+
+/* Chip Select configuration for Epson S1D13513 */
+#define CONFIG_SYS_CS3_START 0x10000000
+#define CONFIG_SYS_CS3_SIZE 0x400000
+#define CONFIG_SYS_CS3_CFG 0xffff3d10
+
+/*
+ * Ethernet configuration
+ */
+#define CONFIG_MPC5xxx_FEC 1
+#define CONFIG_MPC5xxx_FEC_MII100
+#define CONFIG_PHY_ADDR 0x01
+#define CONFIG_NO_AUTOLOAD 1
+
+/*
+ * GPIO configuration
+ *
+ * GPS port configuration
+ *
+ * [29:31] = 01x
+ * AC97 on PSC1
+ * PSC1_0 -> AC97 SDATA out
+ * PSC1_1 -> AC97 SDTA in
+ * PSC1_2 -> AC97 SYNC out
+ * PSC1_3 -> AC97 bitclock out
+ * PSC1_4 -> AC97 reset out
+ *
+ * [28] = Reserved
+ *
+ * [25:27] = 110
+ * SPI on PSC2
+ * PSC2_0 -> MOSI
+ * PSC2_1 -> MISO
+ * PSC2_2 -> n/a
+ * PSC2_3 -> CLK
+ * PSC2_4 -> SS
+ *
+ * [24] = Reserved
+ *
+ * [20:23] = 0001
+ * USB on PSC3
+ * PSC3_0 -> USB_OE OE out
+ * PSC3_1 -> USB_TXN Tx- out
+ * PSC3_2 -> USB_TXP Tx+ out
+ * PSC3_3 -> USB_TXD
+ * PSC3_4 -> USB_RXP Rx+ in
+ * PSC3_5 -> USB_RXN Rx- in
+ * PSC3_6 -> USB_PWR PortPower out
+ * PSC3_7 -> USB_SPEED speed out
+ * PSC3_8 -> USB_SUSPEND suspend
+ * PSC3_9 -> USB_OVRCURNT overcurrent in
+ *
+ * [18:19] = 10
+ * Two UARTs
+ *
+ * [17] = 0
+ * USB differential mode
+ *
+ * [16] = 1
+ * PCI disabled
+ *
+ * [12:15] = 0101
+ * Ethernet 100Mbit with MD
+ * ETH_0 -> ETH Txen
+ * ETH_1 -> ETH TxD0
+ * ETH_2 -> ETH TxD1
+ * ETH_3 -> ETH TxD2
+ * ETH_4 -> ETH TxD3
+ * ETH_5 -> ETH Txerr
+ * ETH_6 -> ETH MDC
+ * ETH_7 -> ETH MDIO
+ * ETH_8 -> ETH RxDv
+ * ETH_9 -> ETH RxCLK
+ * ETH_10 -> ETH Collision
+ * ETH_11 -> ETH TxD
+ * ETH_12 -> ETH RxD0
+ * ETH_13 -> ETH RxD1
+ * ETH_14 -> ETH RxD2
+ * ETH_15 -> ETH RxD3
+ * ETH_16 -> ETH Rxerr
+ * ETH_17 -> ETH CRS
+ *
+ * [9:11] = 111
+ * SPI on PSC6
+ * PSC6_0 -> MISO
+ * PSC6_1 -> SS#
+ * PSC6_2 -> MOSI
+ * PSC6_3 -> CLK
+ *
+ * [8] = 0
+ * IrDA/USB 48MHz clock generated internally
+ *
+ * [6:7] = 01
+ * ATA chip selects on csb_4/5
+ * CSB_4 -> ATA_CS0 out
+ * CSB_5 -> ATA_CS1 out
+ *
+ * [5] = 1
+ * PSC3_4 is used as CS6
+ *
+ * [4] = 1
+ * PSC3_5 is used as CS7
+ *
+ * [2:3] = 00
+ * No Alternatives
+ *
+ * [1] = 0
+ * gpio_wkup_7 is GPIO
+ *
+ * [0] = 0
+ * gpio_wkup_6 is GPIO
+ *
+ */
+#define CONFIG_SYS_GPS_PORT_CONFIG 0x0d75a162
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#define CONFIG_SYS_PROMPT "uboot> " /* Monitor Command Prompt */
+
+#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
+
+#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */
+#if defined(CONFIG_CMD_KGDB)
+#define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */
+#endif
+
+#if defined(CONFIG_CMD_KGDB)
+#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
+#else
+#define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */
+#endif
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
+ /* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS 32 /* max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
+
+#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */
+#define CONFIG_SYS_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */
+
+#define CONFIG_SYS_LOAD_ADDR 0x400000 /* default load address */
+
+#define CONFIG_DISPLAY_BOARDINFO 1
+
+#define CONFIG_SYS_HUSH_PARSER 1
+
+#define CONFIG_CRC32_VERIFY 1
+
+#define CONFIG_BOOTP_DNS
+#define CONFIG_BOOTP_DNS2
+#define CONFIG_BOOTP_SEND_HOSTNAME
+
+#define CONFIG_VERSION_VARIABLE 1
+
+/*
+ * Various low-level settings
+ */
+#define CONFIG_SYS_HID0_INIT HID0_ICE | HID0_ICFI
+#define CONFIG_SYS_HID0_FINAL HID0_ICE
+
+/* no burst access on the LPB */
+#define CONFIG_SYS_CS_BURST 0x00000000
+/* one deadcycle for the 33MHz statemachine */
+#define CONFIG_SYS_CS_DEADCYCLE 0x33333331
+
+#define CONFIG_SYS_BOOTCS_CFG 0x0002d900
+#define CONFIG_SYS_BOOTCS_START CONFIG_SYS_FLASH_BASE
+#define CONFIG_SYS_BOOTCS_SIZE CONFIG_SYS_FLASH_SIZE
+
+#define CONFIG_SYS_RESET_ADDRESS 0xff000000
+
+/*
+ * USB settings
+ */
+#define CONFIG_USB_CLOCK 0x0001bbbb
+/* USB is on PSC3 */
+#define CONFIG_PSC3_USB
+#define CONFIG_USB_CONFIG 0x00000100
+#define CONFIG_USB_OHCI
+#define CONFIG_USB_STORAGE
+
+/*
+ * IDE/ATA stuff Supports IDE harddisk
+ */
+#undef CONFIG_IDE_8xx_PCCARD /* Use IDE with PC Card Adapter */
+#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */
+#undef CONFIG_IDE_LED /* LED for ide not supported */
+
+#define CONFIG_IDE_RESET 1 /* reset for ide supported */
+#define CONFIG_IDE_PREINIT
+#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */
+#define CONFIG_SYS_IDE_MAXDEVICE 2 /* max. 2 drives per IDE bus */
+#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000
+#define CONFIG_SYS_ATA_BASE_ADDR MPC5XXX_ATA
+/* Offset for data I/O */
+#define CONFIG_SYS_ATA_DATA_OFFSET (0x0060)
+/* Offset for normal register accesses */
+#define CONFIG_SYS_ATA_REG_OFFSET (CONFIG_SYS_ATA_DATA_OFFSET)
+/* Offset for alternate registers */
+#define CONFIG_SYS_ATA_ALT_OFFSET (0x005C)
+/* Interval between registers */
+#define CONFIG_SYS_ATA_STRIDE 4
+#define CONFIG_ATAPI 1
+
+/* we enable IDE and FAT support, so we also need partition support */
+#define CONFIG_DOS_PARTITION 1
+
+/*
+ * Open Firmware flat tree
+ */
+#define CONFIG_OF_LIBFDT 1
+#define CONFIG_OF_BOARD_SETUP 1
+
+#define OF_CPU "PowerPC,5200@0"
+#define OF_TBCLK CONFIG_SYS_MPC5XXX_CLKIN
+#define OF_SOC "soc5200@f0000000"
+#define OF_STDOUT_PATH "/soc5200@f0000000/serial@2600"
+
+#endif /* __CONFIG_H */
Code Review / kvmfornfv.git / blobdiff