--- /dev/null
+/*
+ * (C) Copyright 2011 CompuLab, Ltd.
+ * Mike Rapoport <mike@compulab.co.il>
+ * Igor Grinberg <grinberg@compulab.co.il>
+ *
+ * Based on omap3_beagle.h
+ * (C) Copyright 2006-2008
+ * Texas Instruments.
+ * Richard Woodruff <r-woodruff2@ti.com>
+ * Syed Mohammed Khasim <x0khasim@ti.com>
+ *
+ * Configuration settings for the CompuLab CM-T35 and CM-T3730 boards
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ */
+#define CONFIG_OMAP /* in a TI OMAP core */
+#define CONFIG_OMAP34XX /* which is a 34XX */
+#define CONFIG_OMAP_GPIO
+#define CONFIG_CMD_GPIO
+#define CONFIG_CM_T3X /* working with CM-T35 and CM-T3730 */
+#define CONFIG_OMAP_COMMON
+
+#define CONFIG_SDRC /* The chip has SDRC controller */
+
+#include <asm/arch/cpu.h> /* get chip and board defs */
+#include <asm/arch/omap3.h>
+
+/*
+ * Display CPU and Board information
+ */
+#define CONFIG_DISPLAY_CPUINFO
+#define CONFIG_DISPLAY_BOARDINFO
+
+/* Clock Defines */
+#define V_OSCK 26000000 /* Clock output from T2 */
+#define V_SCLK (V_OSCK >> 1)
+
+#define CONFIG_MISC_INIT_R
+
+#define CONFIG_OF_LIBFDT 1
+
+#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */
+#define CONFIG_SETUP_MEMORY_TAGS
+#define CONFIG_INITRD_TAG
+#define CONFIG_REVISION_TAG
+#define CONFIG_SERIAL_TAG
+
+/*
+ * Size of malloc() pool
+ */
+#define CONFIG_ENV_SIZE (16 << 10) /* 16 KiB */
+ /* Sector */
+#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + (128 << 10))
+
+/*
+ * Hardware drivers
+ */
+
+/*
+ * NS16550 Configuration
+ */
+#define V_NS16550_CLK 48000000 /* 48MHz (APLL96/2) */
+
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE (-4)
+#define CONFIG_SYS_NS16550_CLK V_NS16550_CLK
+
+/*
+ * select serial console configuration
+ */
+#define CONFIG_CONS_INDEX 3
+#define CONFIG_SYS_NS16550_COM3 OMAP34XX_UART3
+#define CONFIG_SERIAL3 3 /* UART3 */
+
+/* allow to overwrite serial and ethaddr */
+#define CONFIG_ENV_OVERWRITE
+#define CONFIG_BAUDRATE 115200
+#define CONFIG_SYS_BAUDRATE_TABLE {4800, 9600, 19200, 38400, 57600,\
+ 115200}
+
+#define CONFIG_GENERIC_MMC
+#define CONFIG_MMC
+#define CONFIG_OMAP_HSMMC
+#define CONFIG_DOS_PARTITION
+
+/* USB */
+#define CONFIG_USB_OMAP3
+#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_OMAP
+#define CONFIG_USB_STORAGE
+#define CONFIG_MUSB_UDC
+#define CONFIG_TWL4030_USB
+#define CONFIG_CMD_USB
+
+/* USB device configuration */
+#define CONFIG_USB_DEVICE
+#define CONFIG_USB_TTY
+#define CONFIG_SYS_CONSOLE_IS_IN_ENV
+/* This delay is really for slow-to-power-on USB sticks, not the hub */
+#define CONFIG_USB_HUB_MIN_POWER_ON_DELAY 500
+
+/* commands to include */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_CACHE
+#define CONFIG_CMD_EXT2 /* EXT2 Support */
+#define CONFIG_CMD_FAT /* FAT support */
+#define CONFIG_CMD_MTDPARTS /* Enable MTD parts commands */
+#define CONFIG_MTD_DEVICE /* needed for mtdparts commands */
+#define CONFIG_MTD_PARTITIONS
+#define MTDIDS_DEFAULT "nand0=nand"
+#define MTDPARTS_DEFAULT "mtdparts=nand:512k(x-loader),"\
+ "1920k(u-boot),256k(u-boot-env),"\
+ "4m(kernel),-(fs)"
+
+#define CONFIG_CMD_I2C /* I2C serial bus support */
+#define CONFIG_CMD_MMC /* MMC support */
+#define CONFIG_CMD_NAND /* NAND support */
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_PING
+
+#undef CONFIG_CMD_FLASH /* flinfo, erase, protect */
+#undef CONFIG_CMD_FPGA /* FPGA configuration Support */
+#undef CONFIG_CMD_IMLS /* List all found images */
+
+#define CONFIG_SYS_NO_FLASH
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_OMAP24_I2C_SPEED 100000
+#define CONFIG_SYS_OMAP24_I2C_SLAVE 1
+#define CONFIG_SYS_I2C_OMAP34XX
+#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
+#define CONFIG_I2C_MULTI_BUS
+
+/*
+ * TWL4030
+ */
+#define CONFIG_TWL4030_POWER
+#define CONFIG_TWL4030_LED
+
+/*
+ * Board NAND Info.
+ */
+#define CONFIG_SYS_NAND_QUIET_TEST
+#define CONFIG_NAND_OMAP_GPMC
+#define CONFIG_SYS_NAND_ADDR NAND_BASE /* physical address */
+ /* to access nand */
+#define CONFIG_SYS_NAND_BASE NAND_BASE /* physical address */
+ /* to access nand at */
+ /* CS0 */
+#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND */
+ /* devices */
+#define GPMC_NAND_ECC_LP_x8_LAYOUT
+
+/* Environment information */
+#define CONFIG_BOOTDELAY 3
+#define CONFIG_ZERO_BOOTDELAY_CHECK
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "loadaddr=0x82000000\0" \
+ "usbtty=cdc_acm\0" \
+ "console=ttyO2,115200n8\0" \
+ "mpurate=500\0" \
+ "vram=12M\0" \
+ "dvimode=1024x768MR-16@60\0" \
+ "defaultdisplay=dvi\0" \
+ "mmcdev=0\0" \
+ "mmcroot=/dev/mmcblk0p2 rw\0" \
+ "mmcrootfstype=ext4 rootwait\0" \
+ "nandroot=/dev/mtdblock4 rw\0" \
+ "nandrootfstype=ubifs\0" \
+ "mmcargs=setenv bootargs console=${console} " \
+ "mpurate=${mpurate} " \
+ "vram=${vram} " \
+ "omapfb.mode=dvi:${dvimode} " \
+ "omapdss.def_disp=${defaultdisplay} " \
+ "root=${mmcroot} " \
+ "rootfstype=${mmcrootfstype}\0" \
+ "nandargs=setenv bootargs console=${console} " \
+ "mpurate=${mpurate} " \
+ "vram=${vram} " \
+ "omapfb.mode=dvi:${dvimode} " \
+ "omapdss.def_disp=${defaultdisplay} " \
+ "root=${nandroot} " \
+ "rootfstype=${nandrootfstype}\0" \
+ "loadbootscript=fatload mmc ${mmcdev} ${loadaddr} boot.scr\0" \
+ "bootscript=echo Running bootscript from mmc ...; " \
+ "source ${loadaddr}\0" \
+ "loaduimage=fatload mmc ${mmcdev} ${loadaddr} uImage\0" \
+ "mmcboot=echo Booting from mmc ...; " \
+ "run mmcargs; " \
+ "bootm ${loadaddr}\0" \
+ "nandboot=echo Booting from nand ...; " \
+ "run nandargs; " \
+ "nand read ${loadaddr} 2a0000 400000; " \
+ "bootm ${loadaddr}\0" \
+
+#define CONFIG_CMD_BOOTZ
+#define CONFIG_BOOTCOMMAND \
+ "mmc dev ${mmcdev}; if mmc rescan; then " \
+ "if run loadbootscript; then " \
+ "run bootscript; " \
+ "else " \
+ "if run loaduimage; then " \
+ "run mmcboot; " \
+ "else run nandboot; " \
+ "fi; " \
+ "fi; " \
+ "else run nandboot; fi"
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CONFIG_AUTO_COMPLETE
+#define CONFIG_CMDLINE_EDITING
+#define CONFIG_TIMESTAMP
+#define CONFIG_SYS_AUTOLOAD "no"
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#define CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */
+#define CONFIG_SYS_PROMPT "CM-T3x # "
+#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
+/* Print Buffer Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
+ sizeof(CONFIG_SYS_PROMPT) + 16)
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+/* Boot Argument Buffer Size */
+#define CONFIG_SYS_BARGSIZE (CONFIG_SYS_CBSIZE)
+
+#define CONFIG_SYS_MEMTEST_START (OMAP34XX_SDRC_CS0) /* memtest */
+ /* works on */
+#define CONFIG_SYS_MEMTEST_END (OMAP34XX_SDRC_CS0 + \
+ 0x01F00000) /* 31MB */
+
+#define CONFIG_SYS_LOAD_ADDR (OMAP34XX_SDRC_CS0) /* default */
+ /* load address */
+
+/*
+ * OMAP3 has 12 GP timers, they can be driven by the system clock
+ * (12/13/16.8/19.2/38.4MHz) or by 32KHz clock. We use 13MHz (V_SCLK).
+ * This rate is divided by a local divisor.
+ */
+#define CONFIG_SYS_TIMERBASE (OMAP34XX_GPT2)
+#define CONFIG_SYS_PTV 2 /* Divisor: 2^(PTV+1) => 8 */
+
+/*-----------------------------------------------------------------------
+ * Physical Memory Map
+ */
+#define CONFIG_NR_DRAM_BANKS 1 /* CS1 is never populated */
+#define PHYS_SDRAM_1 OMAP34XX_SDRC_CS0
+
+/*-----------------------------------------------------------------------
+ * FLASH and environment organization
+ */
+
+/* **** PISMO SUPPORT *** */
+/* Configure the PISMO */
+#define PISMO1_NAND_SIZE GPMC_SIZE_128M
+
+/* Monitor at start of flash */
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
+#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 2 sectors */
+
+#define CONFIG_ENV_IS_IN_NAND
+#define SMNAND_ENV_OFFSET 0x260000 /* environment starts here */
+#define CONFIG_ENV_OFFSET SMNAND_ENV_OFFSET
+#define CONFIG_ENV_ADDR SMNAND_ENV_OFFSET
+
+#if defined(CONFIG_CMD_NET)
+#define CONFIG_SMC911X
+#define CONFIG_SMC911X_32_BIT
+#define CM_T3X_SMC911X_BASE 0x2C000000
+#define SB_T35_SMC911X_BASE (CM_T3X_SMC911X_BASE + (16 << 20))
+#define CONFIG_SMC911X_BASE CM_T3X_SMC911X_BASE
+#endif /* (CONFIG_CMD_NET) */
+
+/* additions for new relocation code, must be added to all boards */
+#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
+#define CONFIG_SYS_INIT_RAM_ADDR 0x4020f800
+#define CONFIG_SYS_INIT_RAM_SIZE 0x800
+#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + \
+ CONFIG_SYS_INIT_RAM_SIZE - \
+ GENERATED_GBL_DATA_SIZE)
+
+/* Status LED */
+#define CONFIG_STATUS_LED /* Status LED enabled */
+#define CONFIG_BOARD_SPECIFIC_LED
+#define CONFIG_GPIO_LED
+#define GREEN_LED_GPIO 186 /* CM-T35 Green LED is GPIO186 */
+#define GREEN_LED_DEV 0
+#define STATUS_LED_BIT GREEN_LED_GPIO
+#define STATUS_LED_STATE STATUS_LED_ON
+#define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 2)
+#define STATUS_LED_BOOT GREEN_LED_DEV
+
+#define CONFIG_SPLASHIMAGE_GUARD
+
+/* GPIO banks */
+#ifdef CONFIG_STATUS_LED
+#define CONFIG_OMAP3_GPIO_6 /* GPIO186 is in GPIO bank 6 */
+#endif
+
+/* Display Configuration */
+#define CONFIG_OMAP3_GPIO_2
+#define CONFIG_OMAP3_GPIO_5
+#define CONFIG_VIDEO_OMAP3
+#define LCD_BPP LCD_COLOR16
+
+#define CONFIG_LCD
+#define CONFIG_SPLASH_SCREEN
+#define CONFIG_CMD_BMP
+#define CONFIG_BMP_16BPP
+#define CONFIG_SCF0403_LCD
+
+#define CONFIG_OMAP3_SPI
+
+/* Defines for SPL */
+#define CONFIG_SPL
+#define CONFIG_SPL_FRAMEWORK
+#define CONFIG_SPL_NAND_SIMPLE
+
+#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x300 /* address 0x60000 */
+#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x200 /* 256 KB */
+#define CONFIG_SYS_MMC_SD_FAT_BOOT_PARTITION 1
+#define CONFIG_SPL_FAT_LOAD_PAYLOAD_NAME "u-boot.img"
+
+#define CONFIG_SPL_BOARD_INIT
+#define CONFIG_SPL_LIBCOMMON_SUPPORT
+#define CONFIG_SPL_LIBDISK_SUPPORT
+#define CONFIG_SPL_I2C_SUPPORT
+#define CONFIG_SPL_LIBGENERIC_SUPPORT
+#define CONFIG_SPL_MMC_SUPPORT
+#define CONFIG_SPL_FAT_SUPPORT
+#define CONFIG_SPL_SERIAL_SUPPORT
+#define CONFIG_SPL_NAND_SUPPORT
+#define CONFIG_SPL_NAND_BASE
+#define CONFIG_SPL_NAND_DRIVERS
+#define CONFIG_SPL_NAND_ECC
+#define CONFIG_SPL_GPIO_SUPPORT
+#define CONFIG_SPL_POWER_SUPPORT
+#define CONFIG_SPL_OMAP3_ID_NAND
+#define CONFIG_SPL_LDSCRIPT "$(CPUDIR)/omap-common/u-boot-spl.lds"
+
+/* NAND boot config */
+#define CONFIG_SYS_NAND_5_ADDR_CYCLE
+#define CONFIG_SYS_NAND_PAGE_COUNT 64
+#define CONFIG_SYS_NAND_PAGE_SIZE 2048
+#define CONFIG_SYS_NAND_OOBSIZE 64
+#define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024)
+#define CONFIG_SYS_NAND_BAD_BLOCK_POS NAND_LARGE_BADBLOCK_POS
+/*
+ * Use the ECC/OOB layout from omap_gpmc.h that matches your chip:
+ * SP vs LP, 8bit vs 16bit: GPMC_NAND_HW_ECC_LAYOUT
+ */
+#define CONFIG_SYS_NAND_ECCPOS { 1, 2, 3, 4, 5, 6, 7, 8, 9, \
+ 10, 11, 12 }
+#define CONFIG_SYS_NAND_ECCSIZE 512
+#define CONFIG_SYS_NAND_ECCBYTES 3
+#define CONFIG_NAND_OMAP_ECCSCHEME OMAP_ECC_HAM1_CODE_HW
+
+#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE
+#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000
+
+#define CONFIG_SPL_TEXT_BASE 0x40200800
+#define CONFIG_SPL_MAX_SIZE (54 * 1024) /* 8 KB for stack */
+#define CONFIG_SPL_STACK LOW_LEVEL_SRAM_STACK
+
+/*
+ * Use 0x80008000 as TEXT_BASE here for compatibility reasons with the
+ * older x-loader implementations. And move the BSS area so that it
+ * doesn't overlap with TEXT_BASE.
+ */
+#define CONFIG_SYS_TEXT_BASE 0x80008000
+#define CONFIG_SPL_BSS_START_ADDR 0x80100000
+#define CONFIG_SPL_BSS_MAX_SIZE 0x80000 /* 512 KB */
+
+#define CONFIG_SYS_SPL_MALLOC_START 0x80208000
+#define CONFIG_SYS_SPL_MALLOC_SIZE 0x100000
+
+#endif /* __CONFIG_H */
Code Review / kvmfornfv.git / blobdiff