--- /dev/null
+/*
+ * Copyright (C) 2009 Texas Instruments Incorporated
+ *
+ * Copyright (C) 2011
+ * Heiko Schocher, DENX Software Engineering, hs@denx.de.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#define CONFIG_SYS_NO_FLASH /* that is, no *NOR* flash */
+#define CONFIG_SYS_CONSOLE_INFO_QUIET
+
+/* SoC Configuration */
+#define CONFIG_ARM926EJS /* arm926ejs CPU */
+#define CONFIG_SYS_TIMERBASE 0x01c21400 /* use timer 0 */
+#define CONFIG_SYS_HZ_CLOCK 24000000 /* timer0 freq */
+#define CONFIG_SOC_DM365
+
+#define CONFIG_MACH_TYPE MACH_TYPE_DAVINCI_DM365_EVM
+
+#define CONFIG_HOSTNAME cam_enc_4xx
+
+#define CONFIG_BOARD_LATE_INIT
+#define CONFIG_CAM_ENC_LED_MASK 0x0fc00000
+
+/* Memory Info */
+#define CONFIG_NR_DRAM_BANKS 1
+#define PHYS_SDRAM_1 0x80000000
+#define PHYS_SDRAM_1_SIZE (256 << 20) /* 256 MiB */
+#define DDR_4BANKS /* 4-bank DDR2 (256MB) */
+#define CONFIG_MAX_RAM_BANK_SIZE (256 << 20) /* 256 MB */
+#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
+
+/* Serial Driver info: UART0 for console */
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE -4
+#define CONFIG_SYS_NS16550_COM1 0x01c20000
+#define CONFIG_SYS_NS16550_CLK CONFIG_SYS_HZ_CLOCK
+#define CONFIG_CONS_INDEX 1
+#define CONFIG_BAUDRATE 115200
+
+/* Network Configuration */
+#define CONFIG_DRIVER_TI_EMAC
+#define CONFIG_EMAC_MDIO_PHY_NUM 0
+#define CONFIG_SYS_EMAC_TI_CLKDIV 0xa9 /* 1MHz */
+#define CONFIG_MII
+#define CONFIG_BOOTP_DNS
+#define CONFIG_BOOTP_DNS2
+#define CONFIG_BOOTP_SEND_HOSTNAME
+#define CONFIG_NET_RETRY_COUNT 10
+#define CONFIG_CMD_MII
+#define CONFIG_SYS_DCACHE_OFF
+#define CONFIG_RESET_PHY_R
+
+/* I2C */
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_DAVINCI
+#define CONFIG_SYS_DAVINCI_I2C_SPEED 400000
+#define CONFIG_SYS_DAVINCI_I2C_SLAVE 0x10 /* SMBus host address */
+
+/* NAND: socketed, two chipselects, normally 2 GBytes */
+#define CONFIG_NAND_DAVINCI
+#define CONFIG_SYS_NAND_CS 2
+#define CONFIG_SYS_NAND_USE_FLASH_BBT
+#define CONFIG_SYS_NAND_4BIT_HW_ECC_OOBFIRST
+#define CONFIG_SYS_NAND_PAGE_2K
+
+#define CONFIG_SYS_NAND_LARGEPAGE
+#define CONFIG_SYS_NAND_BASE_LIST { 0x02000000, }
+/* socket has two chipselects, nCE0 gated by address BIT(14) */
+#define CONFIG_SYS_MAX_NAND_DEVICE 1
+
+/* SPI support */
+#define CONFIG_SPI
+#define CONFIG_SPI_FLASH
+#define CONFIG_SPI_FLASH_STMICRO
+#define CONFIG_DAVINCI_SPI
+#define CONFIG_SYS_SPI_BASE DAVINCI_SPI1_BASE
+#define CONFIG_SYS_SPI_CLK davinci_clk_get(SPI_PLLDIV)
+#define CONFIG_SF_DEFAULT_SPEED 3000000
+#define CONFIG_ENV_SPI_MAX_HZ CONFIG_SF_DEFAULT_SPEED
+#define CONFIG_CMD_SF
+
+/* SD/MMC */
+#define CONFIG_MMC
+#define CONFIG_GENERIC_MMC
+#define CONFIG_DAVINCI_MMC
+#define CONFIG_MMC_MBLOCK
+
+/* U-Boot command configuration */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_BDI
+#undef CONFIG_CMD_FLASH
+#undef CONFIG_CMD_FPGA
+#undef CONFIG_CMD_SETGETDCR
+#define CONFIG_CMD_ASKENV
+#define CONFIG_CMD_CACHE
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_SAVES
+
+#ifdef CONFIG_CMD_BDI
+#define CONFIG_CLOCKS
+#endif
+
+#ifdef CONFIG_MMC
+#define CONFIG_DOS_PARTITION
+#define CONFIG_CMD_EXT2
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_MMC
+#endif
+
+#ifdef CONFIG_NAND_DAVINCI
+#define CONFIG_CMD_MTDPARTS
+#define CONFIG_MTD_PARTITIONS
+#define CONFIG_MTD_DEVICE
+#define CONFIG_CMD_NAND
+#define CONFIG_CMD_UBI
+#define CONFIG_CMD_UBIFS
+#define CONFIG_RBTREE
+#define CONFIG_LZO
+#endif
+
+#define CONFIG_CRC32_VERIFY
+#define CONFIG_MX_CYCLIC
+
+/* U-Boot general configuration */
+#define CONFIG_BOOTFILE "uImage" /* Boot file name */
+#define CONFIG_SYS_PROMPT "cam_enc_4xx> " /* Monitor Command Prompt */
+#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
+#define CONFIG_SYS_PBSIZE /* Print buffer size */ \
+ (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+#define CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_LONGHELP
+
+#define CONFIG_MENU
+#define CONFIG_MENU_SHOW
+#define CONFIG_FIT
+#define CONFIG_BOARD_IMG_ADDR_R 0x80000000
+
+#ifdef CONFIG_NAND_DAVINCI
+#define CONFIG_ENV_SIZE (16 << 10)
+#define CONFIG_ENV_IS_IN_NAND
+#define CONFIG_ENV_OFFSET 0x180000
+#define CONFIG_ENV_RANGE 0x040000
+#define CONFIG_ENV_OFFSET_REDUND 0x1c0000
+#undef CONFIG_ENV_IS_IN_FLASH
+#endif
+
+#if defined(CONFIG_MMC) && !defined(CONFIG_ENV_IS_IN_NAND)
+#define CONFIG_CMD_ENV
+#define CONFIG_SYS_MMC_ENV_DEV 0
+#define CONFIG_ENV_SIZE (16 << 10) /* 16 KiB */
+#define CONFIG_ENV_OFFSET (51 << 9) /* Sector 51 */
+#define CONFIG_ENV_IS_IN_MMC
+#undef CONFIG_ENV_IS_IN_FLASH
+#endif
+
+#define CONFIG_BOOTDELAY 3
+/*
+ * 24MHz InputClock / 15 prediv -> 1.6 MHz timer running
+ * Timeout 1 second.
+ */
+#define CONFIG_AIT_TIMER_TIMEOUT 0x186a00
+
+#define CONFIG_CMDLINE_EDITING
+#define CONFIG_VERSION_VARIABLE
+#define CONFIG_TIMESTAMP
+
+/* U-Boot memory configuration */
+#define CONFIG_SYS_MALLOC_LEN (1 << 20) /* 1 MiB */
+#define CONFIG_SYS_MEMTEST_START 0x80000000 /* physical address */
+#define CONFIG_SYS_MEMTEST_END 0x81000000 /* test 16MB RAM */
+
+/* Linux interfacing */
+#define CONFIG_CMDLINE_TAG
+#define CONFIG_SETUP_MEMORY_TAGS
+#define CONFIG_SYS_BARGSIZE 1024 /* bootarg Size */
+#define CONFIG_SYS_LOAD_ADDR 0x80700000 /* kernel address */
+
+#define MTDIDS_DEFAULT "nand0=davinci_nand.0"
+#define MTDPARTS_DEFAULT \
+ "mtdparts=" \
+ "davinci_nand.0:" \
+ "128k(spl)," \
+ "384k(UBLheader)," \
+ "1m(u-boot)," \
+ "512k(env)," \
+ "-(ubi)"
+
+#define CONFIG_SYS_NAND_PAGE_SIZE 0x800
+#define CONFIG_SYS_NAND_BLOCK_SIZE 0x20000
+
+/* Defines for SPL */
+#define CONFIG_SPL
+#define CONFIG_SPL_FRAMEWORK
+#define CONFIG_SPL_BOARD_INIT
+#define CONFIG_SPL_LIBGENERIC_SUPPORT
+#define CONFIG_SPL_NAND_SUPPORT
+#define CONFIG_SPL_NAND_BASE
+#define CONFIG_SPL_NAND_DRIVERS
+#define CONFIG_SPL_NAND_ECC
+#define CONFIG_SPL_NAND_SIMPLE
+#define CONFIG_SYS_NAND_HW_ECC_OOBFIRST
+#define CONFIG_SPL_SERIAL_SUPPORT
+#define CONFIG_SPL_POST_MEM_SUPPORT
+#define CONFIG_SPL_LDSCRIPT "$(BOARDDIR)/u-boot-spl.lds"
+#define CONFIG_SPL_STACK (0x00010000 + 0x7f00)
+
+#define CONFIG_SPL_TEXT_BASE 0x00000020 /*CONFIG_SYS_SRAM_START*/
+/* Provide at least 16MB spacing between us and the Linux Kernel image */
+#define CONFIG_SPL_PAD_TO 12320
+#define CONFIG_SPL_MAX_FOOTPRINT 12288
+
+#ifndef CONFIG_SPL_BUILD
+#define CONFIG_SYS_TEXT_BASE 0x81080000
+#endif
+
+#define CONFIG_SYS_NAND_BASE 0x02000000
+#define CONFIG_SYS_NAND_PAGE_COUNT (CONFIG_SYS_NAND_BLOCK_SIZE / \
+ CONFIG_SYS_NAND_PAGE_SIZE)
+
+#define CONFIG_SYS_NAND_ECCPOS { \
+ 24, 25, 26, 27, 28, \
+ 29, 30, 31, 32, 33, 34, 35, 36, 37, 38, \
+ 39, 40, 41, 42, 43, 44, 45, 46, 47, 48, \
+ 49, 50, 51, 52, 53, 54, 55, 56, 57, 58, \
+ 59, 60, 61, 62, 63 }
+#define CONFIG_SYS_NAND_BAD_BLOCK_POS 0
+#define CONFIG_SYS_NAND_ECCSIZE 0x200
+#define CONFIG_SYS_NAND_ECCBYTES 10
+#define CONFIG_SYS_NAND_MAX_OOBFREE 2
+#define CONFIG_SYS_NAND_MAX_ECCPOS 56
+#define CONFIG_SYS_NAND_OOBSIZE 64
+#define CONFIG_SYS_NAND_5_ADDR_CYCLE
+
+/*
+ * RBL searches from Block n (n = 1..24)
+ * so we can define, how many UBL Headers
+ * we can write before the real spl code
+ */
+#define CONFIG_SYS_NROF_PAGES_NAND_SPL 6
+
+#define CONFIG_SYS_NAND_U_BOOT_DST 0x81080000 /* u-boot TEXT_BASE */
+#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_NAND_U_BOOT_DST
+
+/*
+ * Post tests for memory testing
+ */
+#define CONFIG_POST CONFIG_SYS_POST_MEMORY
+#define _POST_WORD_ADDR 0x0
+
+#define CONFIG_DISPLAY_BOARDINFO
+
+#define CONFIG_SYS_INIT_SP_ADDR CONFIG_SPL_STACK
+
+#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000
+#define CONFIG_SYS_NAND_U_BOOT_SIZE 0xa0000
+#define CONFIG_SYS_NAND_U_BOOT_ERA_SIZE 0x100000
+
+/* for UBL header */
+#define CONFIG_SYS_UBL_BLOCK (CONFIG_SYS_NAND_PAGE_SIZE)
+
+#define CONFIG_SYS_DM36x_PLL1_PLLM 0x55
+#define CONFIG_SYS_DM36x_PLL1_PREDIV 0x8005
+#define CONFIG_SYS_DM36x_PLL2_PLLM 0x09
+#define CONFIG_SYS_DM36x_PLL2_PREDIV 0x8000
+#define CONFIG_SYS_DM36x_PERI_CLK_CTRL 0x243F04FC
+#define CONFIG_SYS_DM36x_PLL1_PLLDIV1 0x801b
+#define CONFIG_SYS_DM36x_PLL1_PLLDIV2 0x8001
+/* POST DIV 680/2 = 340Mhz -> MJCP and HDVICP bus interface clock */
+#define CONFIG_SYS_DM36x_PLL1_PLLDIV3 0x8001
+/*
+ * POST DIV 680/4 = 170Mhz -> EDMA/Peripheral CFG0(1/2 MJCP/HDVICP bus
+ * interface clk)
+ */
+#define CONFIG_SYS_DM36x_PLL1_PLLDIV4 0x8003
+/* POST DIV 680/2 = 340Mhz -> VPSS */
+#define CONFIG_SYS_DM36x_PLL1_PLLDIV5 0x8001
+/* POST DIV 680/9 = 75.6 Mhz -> VENC */
+#define CONFIG_SYS_DM36x_PLL1_PLLDIV6 0x8008
+/*
+ * POST DIV 680/1 = 680Mhz -> DDRx2(with internal divider of 2, clock boils
+ * down to 340 Mhz)
+ */
+#define CONFIG_SYS_DM36x_PLL1_PLLDIV7 0x8000
+/* POST DIV 680/7= 97Mhz-> MMC0/SD0 */
+#define CONFIG_SYS_DM36x_PLL1_PLLDIV8 0x8006
+/* POST DIV 680/28 = 24.3Mhz-> CLKOUT */
+#define CONFIG_SYS_DM36x_PLL1_PLLDIV9 0x801b
+
+#define CONFIG_SYS_DM36x_PLL2_PLLDIV1 0x8011
+/* POST DIV 432/1=432 Mhz -> ARM926/(HDVICP block) clk */
+#define CONFIG_SYS_DM36x_PLL2_PLLDIV2 0x8000
+#define CONFIG_SYS_DM36x_PLL2_PLLDIV3 0x8001
+/* POST DIV 432/21= 20.5714 Mhz->VOICE Codec clk */
+#define CONFIG_SYS_DM36x_PLL2_PLLDIV4 0x8014
+/* POST DIV 432/16=27 Mhz -> VENC(For SD modes, requires) */
+#define CONFIG_SYS_DM36x_PLL2_PLLDIV5 0x800f
+
+/*
+ * READ LATENCY 7 (CL + 2)
+ * CONFIG_PWRDNEN = 1
+ * CONFIG_EXT_STRBEN = 1
+ */
+#define CONFIG_SYS_DM36x_DDR2_DDRPHYCR (0 \
+ | DV_DDR_PHY_EXT_STRBEN \
+ | DV_DDR_PHY_PWRDNEN \
+ | (7 << DV_DDR_PHY_RD_LATENCY_SHIFT))
+
+/*
+ * T_RFC = (trfc/DDR_CLK) - 1 = (195 / 2.941) - 1
+ * T_RP = (trp/DDR_CLK) - 1 = (12.5 / 2.941) - 1
+ * T_RCD = (trcd/DDR_CLK) - 1 = (12.5 / 2.941) - 1
+ * T_WR = (twr/DDR_CLK) - 1 = (15 / 2.941) - 1
+ * T_RAS = (tras/DDR_CLK) - 1 = (45 / 2.941) - 1
+ * T_RC = (trc/DDR_CLK) - 1 = (57.5 / 2.941) - 1
+ * T_RRD = (trrd/DDR_CLK) - 1 = (7.5 / 2.941) - 1
+ * T_WTR = (twtr/DDR_CLK) - 1 = (7.5 / 2.941) - 1
+ */
+#define CONFIG_SYS_DM36x_DDR2_SDTIMR (0 \
+ | (66 << DV_DDR_SDTMR1_RFC_SHIFT) \
+ | (4 << DV_DDR_SDTMR1_RP_SHIFT) \
+ | (4 << DV_DDR_SDTMR1_RCD_SHIFT) \
+ | (5 << DV_DDR_SDTMR1_WR_SHIFT) \
+ | (14 << DV_DDR_SDTMR1_RAS_SHIFT) \
+ | (19 << DV_DDR_SDTMR1_RC_SHIFT) \
+ | (2 << DV_DDR_SDTMR1_RRD_SHIFT) \
+ | (2 << DV_DDR_SDTMR1_WTR_SHIFT))
+
+/*
+ * T_RASMAX = (trasmax/refresh_rate) - 1 = (70K / 7812.6) - 1
+ * T_XP = tCKE - 1 = 3 - 2
+ * T_XSNR= ((trfc + 10)/DDR_CLK) - 1 = (205 / 2.941) - 1
+ * T_XSRD = txsrd - 1 = 200 - 1
+ * T_RTP = (trtp/DDR_CLK) - 1 = (7.5 / 2.941) - 1
+ * T_CKE = tcke - 1 = 3 - 1
+ */
+#define CONFIG_SYS_DM36x_DDR2_SDTIMR2 (0 \
+ | (8 << DV_DDR_SDTMR2_RASMAX_SHIFT) \
+ | (2 << DV_DDR_SDTMR2_XP_SHIFT) \
+ | (69 << DV_DDR_SDTMR2_XSNR_SHIFT) \
+ | (199 << DV_DDR_SDTMR2_XSRD_SHIFT) \
+ | (2 << DV_DDR_SDTMR2_RTP_SHIFT) \
+ | (2 << DV_DDR_SDTMR2_CKE_SHIFT))
+
+/* PR_OLD_COUNT = 0xfe */
+#define CONFIG_SYS_DM36x_DDR2_PBBPR 0x000000FE
+/* refresh rate = 0x768 */
+#define CONFIG_SYS_DM36x_DDR2_SDRCR 0x00000768
+
+#define CONFIG_SYS_DM36x_DDR2_SDBCR (0 \
+ | (2 << DV_DDR_SDCR_PAGESIZE_SHIFT) \
+ | (3 << DV_DDR_SDCR_IBANK_SHIFT) \
+ | (5 << DV_DDR_SDCR_CL_SHIFT) \
+ | (1 << DV_DDR_SDCR_BUS_WIDTH_SHIFT) \
+ | (1 << DV_DDR_SDCR_TIMUNLOCK_SHIFT) \
+ | (1 << DV_DDR_SDCR_DDREN_SHIFT) \
+ | (0 << DV_DDR_SDCR_DDRDRIVE0_SHIFT) \
+ | (1 << DV_DDR_SDCR_DDR2EN_SHIFT) \
+ | (1 << DV_DDR_SDCR_DDR_DDQS_SHIFT) \
+ | (1 << DV_DDR_SDCR_BOOTUNLOCK_SHIFT))
+
+#define CONFIG_SYS_DM36x_AWCCR 0xff
+#define CONFIG_SYS_DM36x_AB1CR 0x40400204
+#define CONFIG_SYS_DM36x_AB2CR 0x04ca2650
+
+/* All Video Inputs */
+#define CONFIG_SYS_DM36x_PINMUX0 0x00000000
+/*
+ * All Video Outputs,
+ * GPIO 86, 87 + 90 0x0000f030
+ */
+#define CONFIG_SYS_DM36x_PINMUX1 0x00530002
+#define CONFIG_SYS_DM36x_PINMUX2 0x00001815
+/*
+ * SPI1, UART1, I2C, SD0, SD1, McBSP0, CLKOUTs
+ * GPIO 25 0x60000000
+ */
+#define CONFIG_SYS_DM36x_PINMUX3 0x9b5affff
+/*
+ * MMC/SD0 instead of MS, SPI0
+ * GPIO 34 0x0000c000
+ */
+#define CONFIG_SYS_DM36x_PINMUX4 0x00002655
+
+/*
+ * Default environment settings
+ */
+
+#define DVN4XX_UBOOT_ADDR_R_RAM 0x80000000
+/* (DVN4XX_UBOOT_ADDR_R_RAM + CONFIG_SYS_NAND_PAGE_SIZE) */
+#define DVN4XX_UBOOT_ADDR_R_NAND_SPL 0x80000800
+/*
+ * (DVN4XX_UBOOT_ADDR_R_NAND_SPL + (CONFIG_SYS_NROF_PAGES_NAND_SPL * \
+ * CONFIG_SYS_NAND_PAGE_SIZE))
+ */
+#define DVN4XX_UBOOT_ADDR_R_UBOOT 0x80003800
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "u_boot_addr_r=" __stringify(DVN4XX_UBOOT_ADDR_R_RAM) "\0" \
+ "u-boot=" __stringify(CONFIG_HOSTNAME) "/u-boot.ubl\0" \
+ "load=tftp ${u_boot_addr_r} ${u-boot}\0" \
+ "pagesz=" __stringify(CONFIG_SYS_NAND_PAGE_SIZE) "\0" \
+ "writeheader=nandrbl rbl;nand erase 20000 ${pagesz};" \
+ "nand write ${u_boot_addr_r} 20000 ${pagesz};" \
+ "nandrbl uboot\0" \
+ "writenand_spl=nandrbl rbl;nand erase 0 3000;" \
+ "nand write " __stringify(DVN4XX_UBOOT_ADDR_R_NAND_SPL) \
+ " 0 3000;nandrbl uboot\0" \
+ "writeuboot=nandrbl uboot;" \
+ "nand erase " __stringify(CONFIG_SYS_NAND_U_BOOT_OFFS) " "\
+ __stringify(CONFIG_SYS_NAND_U_BOOT_ERA_SIZE) \
+ ";nand write " __stringify(DVN4XX_UBOOT_ADDR_R_UBOOT) \
+ " " __stringify(CONFIG_SYS_NAND_U_BOOT_OFFS) " " \
+ __stringify(CONFIG_SYS_NAND_U_BOOT_SIZE) "\0" \
+ "update=run load writenand_spl writeuboot\0" \
+ "bootcmd=run net_nfs\0" \
+ "rootpath=/opt/eldk-arm/arm\0" \
+ "mtdids=" MTDIDS_DEFAULT "\0" \
+ "mtdparts=" MTDPARTS_DEFAULT "\0" \
+ "netdev=eth0\0" \
+ "addmtd=setenv bootargs ${bootargs} ${mtdparts}\0" \
+ "addmisc=setenv bootargs ${bootargs} app_reset=${app_reset}\0" \
+ "addcon=setenv bootargs ${bootargs} console=ttyS0," \
+ "${baudrate}n8\0" \
+ "addip=setenv bootargs ${bootargs} " \
+ "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
+ ":${hostname}:${netdev}:off eth=${ethaddr} panic=1\0" \
+ "rootpath=/opt/eldk-arm/arm\0" \
+ "nfsargs=setenv bootargs root=/dev/nfs rw " \
+ "nfsroot=${serverip}:${rootpath}\0" \
+ "bootfile=" __stringify(CONFIG_HOSTNAME) "/uImage \0" \
+ "kernel_addr_r=80600000\0" \
+ "load_kernel=tftp ${kernel_addr_r} ${bootfile}\0" \
+ "ubi_load_kernel=ubi part ubi 2048;ubifsmount ubi:${img_volume};" \
+ "ubifsload ${kernel_addr_r} boot/uImage\0" \
+ "fit_addr_r=" __stringify(CONFIG_BOARD_IMG_ADDR_R) "\0" \
+ "img_addr_r=" __stringify(CONFIG_BOARD_IMG_ADDR_R) "\0" \
+ "img_file=" __stringify(CONFIG_HOSTNAME) "/ait.itb\0" \
+ "header_addr=20000\0" \
+ "img_writeheader=nandrbl rbl;" \
+ "nand erase ${header_addr} ${pagesz};" \
+ "nand write ${img_addr_r} ${header_addr} ${pagesz};" \
+ "nandrbl uboot\0" \
+ "img_writespl=nandrbl rbl;nand erase 0 3000;" \
+ "nand write ${img_addr_r} 0 3000;nandrbl uboot\0" \
+ "img_writeuboot=nandrbl uboot;" \
+ "nand erase " __stringify(CONFIG_SYS_NAND_U_BOOT_OFFS) " "\
+ __stringify(CONFIG_SYS_NAND_U_BOOT_ERA_SIZE) \
+ ";nand write ${img_addr_r} " \
+ __stringify(CONFIG_SYS_NAND_U_BOOT_OFFS) " " \
+ __stringify(CONFIG_SYS_NAND_U_BOOT_SIZE) "\0" \
+ "img_writedfenv=ubi part ubi 2048;" \
+ "ubi write ${img_addr_r} default ${filesize}\0" \
+ "img_volume=rootfs1\0" \
+ "img_writeramdisk=ubi part ubi 2048;" \
+ "ubi write ${img_addr_r} ${img_volume} ${filesize}\0" \
+ "load_img=tftp ${fit_addr_r} ${img_file}\0" \
+ "net_nfs=run load_kernel; " \
+ "run nfsargs addip addcon addmtd addmisc;" \
+ "bootm ${kernel_addr_r}\0" \
+ "ubi_ubi=run ubi_load_kernel; " \
+ "run ubiargs addip addcon addmtd addmisc;" \
+ "bootm ${kernel_addr_r}\0" \
+ "ubiargs=setenv bootargs ubi.mtd=4,2048" \
+ " root=ubi0:${img_volume} rw rootfstype=ubifs\0" \
+ "app_reset=no\0" \
+ "dvn_app_vers=void\0" \
+ "dvn_boot_vers=void\0" \
+ "savenewvers=run savetmpparms restoreparms; saveenv;" \
+ "run restoretmpparms\0" \
+ "savetmpparms=setenv y_ipaddr ${ipaddr};" \
+ "setenv y_netmask ${netmask};" \
+ "setenv y_serverip ${serverip};" \
+ "setenv y_gatewayip ${gatewayip}\0" \
+ "saveparms=setenv x_ipaddr ${ipaddr};" \
+ "setenv x_netmask ${netmask};" \
+ "setenv x_serverip ${serverip};" \
+ "setenv x_gatewayip ${gatewayip}\0" \
+ "restoreparms=setenv ipaddr ${x_ipaddr};" \
+ "setenv netmask ${x_netmask};" \
+ "setenv serverip ${x_serverip};" \
+ "setenv gatewayip ${x_gatewayip}\0" \
+ "restoretmpparms=setenv ipaddr ${y_ipaddr};" \
+ "setenv netmask ${y_netmask};" \
+ "setenv serverip ${y_serverip};" \
+ "setenv gatewayip ${y_gatewayip}\0" \
+ "\0"
+
+/* USB Configuration */
+#define CONFIG_USB_DAVINCI
+#define CONFIG_MUSB_HCD
+#define CONFIG_DV_USBPHY_CTL (USBPHY_SESNDEN | USBPHY_VBDTCTEN | \
+ USBPHY_PHY24MHZ)
+
+#define CONFIG_CMD_USB /* include support for usb cmd */
+#define CONFIG_USB_STORAGE /* MSC class support */
+#define CONFIG_CMD_STORAGE /* inclue support for usb-storage cmd */
+#define CONFIG_CMD_FAT /* inclue support for FAT/storage */
+#define CONFIG_DOS_PARTITION /* inclue support for FAT/storage */
+
+#undef DAVINCI_DM365EVM
+#define PINMUX4_USBDRVBUS_BITCLEAR 0x3000
+#define PINMUX4_USBDRVBUS_BITSET 0x2000
+
+#endif /* __CONFIG_H */
Code Review / kvmfornfv.git / blobdiff