--- /dev/null
+/*
+ * U-boot - Configuration file for BF533 STAMP board
+ */
+
+#ifndef __CONFIG_BF533_STAMP_H__
+#define __CONFIG_BF533_STAMP_H__
+
+#include <asm/config-pre.h>
+
+
+/*
+ * Processor Settings
+ */
+#define CONFIG_BFIN_CPU bf533-0.3
+#define CONFIG_BFIN_BOOT_MODE BFIN_BOOT_BYPASS
+
+/*
+ * Clock Settings
+ * CCLK = (CLKIN * VCO_MULT) / CCLK_DIV
+ * SCLK = (CLKIN * VCO_MULT) / SCLK_DIV
+ */
+/* CONFIG_CLKIN_HZ is any value in Hz */
+#define CONFIG_CLKIN_HZ 11059200
+/* CLKIN_HALF controls the DF bit in PLL_CTL 0 = CLKIN */
+/* 1 = CLKIN / 2 */
+#define CONFIG_CLKIN_HALF 0
+/* PLL_BYPASS controls the BYPASS bit in PLL_CTL 0 = do not bypass */
+/* 1 = bypass PLL */
+#define CONFIG_PLL_BYPASS 0
+/* VCO_MULT controls the MSEL (multiplier) bits in PLL_CTL */
+/* Values can range from 0-63 (where 0 means 64) */
+#define CONFIG_VCO_MULT 45
+/* CCLK_DIV controls the core clock divider */
+/* Values can be 1, 2, 4, or 8 ONLY */
+#define CONFIG_CCLK_DIV 1
+/* SCLK_DIV controls the system clock divider */
+/* Values can range from 1-15 */
+#define CONFIG_SCLK_DIV 6 /* note: 1.2 boards can go faster */
+
+/*
+ * Memory Settings
+ */
+#define CONFIG_MEM_ADD_WDTH 11
+#define CONFIG_MEM_SIZE 128
+
+#define CONFIG_EBIU_SDRRC_VAL 0x268
+#define CONFIG_EBIU_SDGCTL_VAL 0x911109
+
+#define CONFIG_EBIU_AMGCTL_VAL 0xFF
+#define CONFIG_EBIU_AMBCTL0_VAL 0xBBC3BBC3
+#define CONFIG_EBIU_AMBCTL1_VAL 0x99B39983
+
+#define CONFIG_SYS_MONITOR_LEN (256 * 1024)
+#define CONFIG_SYS_MALLOC_LEN (384 * 1024)
+
+
+/*
+ * Network Settings
+ */
+#define ADI_CMDS_NETWORK 1
+#define CONFIG_SMC91111 1
+#define CONFIG_SMC91111_BASE 0x20300300
+#define SMC91111_EEPROM_INIT() \
+ do { \
+ bfin_write_FIO_DIR(bfin_read_FIO_DIR() | PF1 | PF0); \
+ bfin_write_FIO_FLAG_C(PF1); \
+ bfin_write_FIO_FLAG_S(PF0); \
+ SSYNC(); \
+ } while (0)
+#define CONFIG_HOSTNAME bf533-stamp
+/* Uncomment next line to use fixed MAC address */
+/* #define CONFIG_ETHADDR 02:80:ad:20:31:b8 */
+
+
+/* I2C */
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_SOFT /* I2C bit-banged */
+#define CONFIG_SYS_I2C_SOFT_SPEED 50000
+#define CONFIG_SYS_I2C_SOFT_SLAVE 0
+/*
+ * Software (bit-bang) I2C driver configuration
+ */
+#define CONFIG_SOFT_I2C_GPIO_SCL GPIO_PF3
+#define CONFIG_SOFT_I2C_GPIO_SDA GPIO_PF2
+
+/*
+ * Flash Settings
+ */
+#define CONFIG_FLASH_CFI_DRIVER
+#define CONFIG_SYS_FLASH_BASE 0x20000000
+#define CONFIG_SYS_FLASH_CFI
+#define CONFIG_SYS_FLASH_CFI_AMD_RESET
+#define CONFIG_SYS_MAX_FLASH_BANKS 1
+#define CONFIG_SYS_MAX_FLASH_SECT 67
+
+/*
+ * SPI Settings
+ */
+#define CONFIG_BFIN_SPI
+#define CONFIG_ENV_SPI_MAX_HZ 30000000
+#define CONFIG_SF_DEFAULT_SPEED 30000000
+#define CONFIG_SPI_FLASH
+#define CONFIG_SPI_FLASH_ALL
+
+
+/*
+ * Env Storage Settings
+ */
+#if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_SPI_MASTER)
+#define CONFIG_ENV_IS_IN_SPI_FLASH
+#define CONFIG_ENV_OFFSET 0x10000
+#define CONFIG_ENV_SIZE 0x2000
+#define CONFIG_ENV_SECT_SIZE 0x10000
+#else
+#define CONFIG_ENV_IS_IN_FLASH
+#define CONFIG_ENV_OFFSET 0x4000
+#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + CONFIG_ENV_OFFSET)
+#define CONFIG_ENV_SIZE 0x2000
+#define CONFIG_ENV_SECT_SIZE 0x2000
+#endif
+#if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_BYPASS)
+#define ENV_IS_EMBEDDED
+#else
+#define CONFIG_ENV_IS_EMBEDDED_IN_LDR
+#endif
+#ifdef ENV_IS_EMBEDDED
+/* WARNING - the following is hand-optimized to fit within
+ * the sector before the environment sector. If it throws
+ * an error during compilation remove an object here to get
+ * it linked after the configuration sector.
+ */
+# define LDS_BOARD_TEXT \
+ arch/blackfin/lib/built-in.o (.text*); \
+ arch/blackfin/cpu/built-in.o (.text*); \
+ . = DEFINED(env_offset) ? env_offset : .; \
+ common/env_embedded.o (.text*);
+#endif
+
+
+/*
+ * I2C Settings
+ */
+#define CONFIG_SYS_I2C_SOFT
+#ifdef CONFIG_SYS_I2C_SOFT
+#define CONFIG_SYS_I2C
+#define CONFIG_SOFT_I2C_GPIO_SCL GPIO_PF3
+#define CONFIG_SOFT_I2C_GPIO_SDA GPIO_PF2
+#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */
+#define CONFIG_SYS_I2C_SOFT_SPEED 50000
+#define CONFIG_SYS_I2C_SOFT_SLAVE 0
+#endif
+
+/*
+ * Compact Flash / IDE / ATA Settings
+ */
+
+/* Enabled below option for CF support */
+/* #define CONFIG_STAMP_CF */
+#if defined(CONFIG_STAMP_CF)
+#define CONFIG_MISC_INIT_R
+#define CONFIG_DOS_PARTITION 1
+#undef CONFIG_IDE_8xx_DIRECT /* no pcmcia interface required */
+#undef CONFIG_IDE_LED /* no led for ide supported */
+#undef CONFIG_IDE_RESET /* no reset for ide supported */
+
+#define CONFIG_SYS_IDE_MAXBUS 1
+#define CONFIG_SYS_IDE_MAXDEVICE (CONFIG_SYS_IDE_MAXBUS * 1)
+
+#define CONFIG_SYS_ATA_BASE_ADDR 0x20200000
+#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000
+
+#define CONFIG_SYS_ATA_DATA_OFFSET 0x0020 /* data I/O */
+#define CONFIG_SYS_ATA_REG_OFFSET 0x0020 /* normal register accesses */
+#define CONFIG_SYS_ATA_ALT_OFFSET 0x0007 /* alternate registers */
+
+#define CONFIG_SYS_ATA_STRIDE 2
+
+#undef CONFIG_EBIU_AMBCTL1_VAL
+#define CONFIG_EBIU_AMBCTL1_VAL 0x99B3ffc2
+#endif
+
+
+/*
+ * Misc Settings
+ */
+#define CONFIG_RTC_BFIN
+#define CONFIG_UART_CONSOLE 0
+#define CONFIG_CC_OPTIMIZE_LIBS_FOR_SPEED
+
+/* FLASH/ETHERNET uses the same async bank */
+#define SHARED_RESOURCES 1
+
+/* define to enable boot progress via leds */
+/* #define CONFIG_SHOW_BOOT_PROGRESS */
+
+/* define to enable run status via led */
+/* #define CONFIG_STATUS_LED */
+#ifdef CONFIG_STATUS_LED
+#define CONFIG_GPIO_LED
+#define CONFIG_BOARD_SPECIFIC_LED
+/* use LED0 to indicate booting/alive */
+#define STATUS_LED_BOOT 0
+#define STATUS_LED_BIT GPIO_PF2
+#define STATUS_LED_STATE STATUS_LED_ON
+#define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 4)
+/* use LED1 to indicate crash */
+#define STATUS_LED_CRASH 1
+#define STATUS_LED_BIT1 GPIO_PF3
+#define STATUS_LED_STATE1 STATUS_LED_ON
+#define STATUS_LED_PERIOD1 (CONFIG_SYS_HZ / 2)
+/* #define STATUS_LED_BIT2 GPIO_PF4 */
+#endif
+
+/* define to enable splash screen support */
+/* #define CONFIG_VIDEO */
+
+
+/*
+ * Pull in common ADI header for remaining command/environment setup
+ */
+#include <configs/bfin_adi_common.h>
+
+#endif
Code Review / kvmfornfv.git / blobdiff