Add qemu 2.4.0

[kvmfornfv.git] / qemu / roms / u-boot / include / configs / bcm28155_ap.h

diff --git a/qemu/roms/u-boot/include/configs/bcm28155_ap.h b/qemu/roms/u-boot/include/configs/bcm28155_ap.h
new file mode 100644 (file)
index 0000000..e93b855
--- /dev/null
+++ b/qemu/roms/u-boot/include/configs/bcm28155_ap.h
@@ -0,0 +1,140 @@
+/*
+ * Copyright 2013 Broadcom Corporation.
+ *
+ * SPDX-License-Identifier:      GPL-2.0+
+ */
+
+#ifndef __BCM28155_AP_H
+#define __BCM28155_AP_H
+
+#include <linux/sizes.h>
+#include <asm/arch/sysmap.h>
+
+/* Architecture, CPU, chip, mach, etc */
+#define CONFIG_ARMV7
+#define CONFIG_KONA
+#define CONFIG_SKIP_LOWLEVEL_INIT
+
+/*
+ * Memory configuration
+ */
+#define CONFIG_SYS_TEXT_BASE           0xae000000
+
+#define CONFIG_SYS_SDRAM_BASE          0x80000000
+#define CONFIG_SYS_SDRAM_SIZE          0x80000000
+#define CONFIG_NR_DRAM_BANKS           1
+
+#define CONFIG_SYS_MALLOC_LEN          SZ_4M   /* see armv7/start.S. */
+#define CONFIG_STACKSIZE               SZ_256K
+
+/* GPIO Driver */
+#define CONFIG_KONA_GPIO
+
+/* MMC/SD Driver */
+#define CONFIG_SDHCI
+#define CONFIG_MMC_SDMA
+#define CONFIG_KONA_SDHCI
+#define CONFIG_MMC
+#define CONFIG_GENERIC_MMC
+
+#define CONFIG_SYS_SDIO_BASE0 SDIO1_BASE_ADDR
+#define CONFIG_SYS_SDIO_BASE1 SDIO2_BASE_ADDR
+#define CONFIG_SYS_SDIO_BASE2 SDIO3_BASE_ADDR
+#define CONFIG_SYS_SDIO_BASE3 SDIO4_BASE_ADDR
+#define CONFIG_SYS_SDIO0_MAX_CLK 48000000
+#define CONFIG_SYS_SDIO1_MAX_CLK 48000000
+#define CONFIG_SYS_SDIO2_MAX_CLK 48000000
+#define CONFIG_SYS_SDIO3_MAX_CLK 48000000
+#define CONFIG_SYS_SDIO0 "sdio1"
+#define CONFIG_SYS_SDIO1 "sdio2"
+#define CONFIG_SYS_SDIO2 "sdio3"
+#define CONFIG_SYS_SDIO3 "sdio4"
+
+/* I2C Driver */
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_KONA
+#define CONFIG_SYS_SPD_BUS_NUM 3       /* Start with PMU bus */
+#define CONFIG_SYS_MAX_I2C_BUS 4
+#define CONFIG_SYS_I2C_BASE0   BSC1_BASE_ADDR
+#define CONFIG_SYS_I2C_BASE1   BSC2_BASE_ADDR
+#define CONFIG_SYS_I2C_BASE2   BSC3_BASE_ADDR
+#define CONFIG_SYS_I2C_BASE3   PMU_BSC_BASE_ADDR
+
+/* Timer Driver */
+#define CONFIG_SYS_TIMER_RATE          32000
+#define CONFIG_SYS_TIMER_COUNTER       (TIMER_BASE_ADDR + 4) /* STCLO offset */
+
+/* Init functions */
+#define CONFIG_MISC_INIT_R     /* board's misc_init_r function */
+
+/* Some commands use this as the default load address */
+#define CONFIG_SYS_LOAD_ADDR           CONFIG_SYS_SDRAM_BASE
+
+/* No mtest functions as recommended */
+#undef CONFIG_CMD_MEMORY
+
+/*
+ * This is the initial SP which is used only briefly for relocating the u-boot
+ * image to the top of SDRAM. After relocation u-boot moves the stack to the
+ * proper place.
+ */
+#define CONFIG_SYS_INIT_SP_ADDR                CONFIG_SYS_TEXT_BASE
+
+/* Serial Info */
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+/* Post pad 3 bytes after each reg addr */
+#define CONFIG_SYS_NS16550_REG_SIZE    (-4)
+#define CONFIG_SYS_NS16550_CLK         13000000
+#define CONFIG_CONS_INDEX              1
+#define CONFIG_SYS_NS16550_COM1                0x3e000000
+
+#define CONFIG_BAUDRATE                        115200
+
+#define CONFIG_ENV_SIZE                        0x10000
+#define CONFIG_ENV_IS_NOWHERE
+
+#define CONFIG_SYS_NO_FLASH    /* Not using NAND/NOR unmanaged flash */
+
+/* console configuration */
+#define CONFIG_SYS_CBSIZE              1024    /* Console buffer size */
+#define CONFIG_SYS_PBSIZE              (CONFIG_SYS_CBSIZE + \
+                       sizeof(CONFIG_SYS_PROMPT) + 16) /* Printbuffer size */
+#define CONFIG_SYS_MAXARGS             64
+#define CONFIG_SYS_BARGSIZE            CONFIG_SYS_CBSIZE
+
+/*
+ * One partition type must be defined for part.c
+ * This is necessary for the fatls command to work on an SD card
+ * for example.
+ */
+#define CONFIG_DOS_PARTITION
+
+/* version string, parser, etc */
+#define CONFIG_VERSION_VARIABLE
+#define CONFIG_AUTO_COMPLETE
+#define CONFIG_SYS_HUSH_PARSER
+#define CONFIG_CMDLINE_EDITING
+#define CONFIG_SYS_LONGHELP
+
+#define CONFIG_CRC32_VERIFY
+#define CONFIG_MX_CYCLIC
+
+/* Initial upstream - boot to cmd prompt only */
+#define CONFIG_BOOTCOMMAND             ""
+
+/* Commands */
+#include <config_cmd_default.h>
+#define CONFIG_CMD_ASKENV
+#define CONFIG_CMD_CACHE
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_GPIO
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_MMC
+#define CONFIG_CMD_BOOTZ
+#define CONFIG_FAT_WRITE
+
+#undef CONFIG_CMD_NET
+#undef CONFIG_CMD_NFS
+
+#endif /* __BCM28155_AP_H */