--- /dev/null
+/*
+ * (C) Copyright 2006-2008
+ * Stefan Roese, DENX Software Engineering, sr@denx.de.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*-----------------------------------------------------------------------
+ * High Level Configuration Options
+ *----------------------------------------------------------------------*/
+#define CONFIG_ALPR 1 /* Board is ebony */
+#define CONFIG_440GX 1 /* Specifc GX support */
+#define CONFIG_440 1 /* ... PPC440 family */
+#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */
+#define CONFIG_LAST_STAGE_INIT 1 /* call last_stage_init() */
+
+#define CONFIG_SYS_TEXT_BASE 0xFFFC0000
+
+#define CONFIG_SYS_CLK_FREQ 33333333 /* external freq to pll */
+#define CONFIG_4xx_DCACHE /* Enable i- and d-cache */
+
+/*-----------------------------------------------------------------------
+ * Base addresses -- Note these are effective addresses where the
+ * actual resources get mapped (not physical addresses)
+ *----------------------------------------------------------------------*/
+#define CONFIG_SYS_SDRAM_BASE 0x00000000 /* _must_ be 0 */
+#define CONFIG_SYS_FLASH_BASE 0xffe00000 /* start of FLASH */
+#define CONFIG_SYS_MONITOR_BASE 0xfffc0000 /* start of monitor */
+#define CONFIG_SYS_PCI_MEMBASE 0x80000000 /* mapped pci memory */
+#define CONFIG_SYS_PCI_MEMSIZE 0x40000000 /* size of mapped pci memory */
+#define CONFIG_SYS_ISRAM_BASE 0xc0000000 /* internal SRAM */
+#define CONFIG_SYS_PCI_BASE 0xd0000000 /* internal PCI regs */
+#define CONFIG_SYS_PCI_MEMBASE1 CONFIG_SYS_PCI_MEMBASE + 0x10000000
+#define CONFIG_SYS_PCI_MEMBASE2 CONFIG_SYS_PCI_MEMBASE1 + 0x10000000
+#define CONFIG_SYS_PCI_MEMBASE3 CONFIG_SYS_PCI_MEMBASE2 + 0x10000000
+
+
+#define CONFIG_SYS_FPGA_BASE (CONFIG_SYS_PERIPHERAL_BASE + 0x08300000)
+#define CONFIG_SYS_NVRAM_BASE_ADDR (CONFIG_SYS_PERIPHERAL_BASE + 0x08000000)
+
+/*-----------------------------------------------------------------------
+ * Initial RAM & stack pointer (placed in internal SRAM)
+ *----------------------------------------------------------------------*/
+#define CONFIG_SYS_TEMP_STACK_OCM 1
+#define CONFIG_SYS_OCM_DATA_ADDR CONFIG_SYS_ISRAM_BASE
+#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_ISRAM_BASE /* Initial RAM address */
+#define CONFIG_SYS_INIT_RAM_SIZE 0x2000 /* Size of used area in RAM */
+
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET (CONFIG_SYS_GBL_DATA_OFFSET - 0x4)
+
+#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
+#define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc*/
+
+/*-----------------------------------------------------------------------
+ * Serial Port
+ *----------------------------------------------------------------------*/
+#define CONFIG_CONS_INDEX 2 /* Use UART1 */
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE 1
+#define CONFIG_SYS_NS16550_CLK get_serial_clock()
+
+#undef CONFIG_SYS_EXT_SERIAL_CLOCK
+#define CONFIG_BAUDRATE 115200
+
+#define CONFIG_SYS_BAUDRATE_TABLE \
+ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
+
+/*-----------------------------------------------------------------------
+ * FLASH related
+ *----------------------------------------------------------------------*/
+#define CONFIG_SYS_FLASH_CFI 1 /* The flash is CFI compatible */
+#define CONFIG_FLASH_CFI_DRIVER 1 /* Use common CFI driver */
+#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
+#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max number of sectors on one chip */
+#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */
+#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
+#define CONFIG_SYS_FLASH_QUIET_TEST 1 /* don't warn upon unknown flash */
+
+#define CONFIG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */
+
+#define CONFIG_ENV_SECT_SIZE 0x10000 /* size of one complete sector */
+#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE-CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */
+
+/* Address and size of Redundant Environment Sector */
+#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR-CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
+
+/*-----------------------------------------------------------------------
+ * DDR SDRAM
+ *----------------------------------------------------------------------*/
+#undef CONFIG_SPD_EEPROM /* Don't use SPD EEPROM for setup */
+#define CONFIG_SDRAM_BANK0 1 /* init onboard DDR SDRAM bank 0 */
+#undef CONFIG_SDRAM_ECC /* enable ECC support */
+#define CONFIG_SYS_SDRAM_TABLE { \
+ {(256 << 20), 13, 0x000C4001}, /* 256MB mode 3, 13x10(4)*/ \
+ {(64 << 20), 12, 0x00082001}} /* 64MB mode 2, 12x9(4) */
+
+/*-----------------------------------------------------------------------
+ * I2C
+ *----------------------------------------------------------------------*/
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_PPC4XX
+#define CONFIG_SYS_I2C_PPC4XX_CH0
+#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 100000
+#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F
+#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} } /* Don't probe these addrs */
+
+/*-----------------------------------------------------------------------
+ * I2C EEPROM (PCF8594C)
+ *----------------------------------------------------------------------*/
+#define CONFIG_SYS_I2C_EEPROM_ADDR 0x54 /* EEPROM PCF8594C */
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */
+/* mask of address bits that overflow into the "EEPROM chip address" */
+#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW 0x07
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 /* The Philips PCF8594C has */
+ /* 8 byte page write mode using */
+ /* last 3 bits of the address */
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 40 /* and takes up to 40 msec */
+
+#define CONFIG_PREBOOT "echo;" \
+ "echo Type \"run kernelx\" to boot the system;" \
+ "echo"
+
+#undef CONFIG_BOOTARGS
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "netdev=eth3\0" \
+ "hostname=alpr\0" \
+ "fdt_file=alpr/alpr.dtb\0" \
+ "fdt_addr=400000\0" \
+ "nfsargs=setenv bootargs root=/dev/nfs rw " \
+ "nfsroot=${serverip}:${rootpath} ${init}\0" \
+ "ramargs=setenv bootargs root=/dev/ram rw\0" \
+ "addip=setenv bootargs ${bootargs} " \
+ "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
+ ":${hostname}:${netdev}:off panic=1\0" \
+ "addtty=setenv bootargs ${bootargs} console=ttyS1,${baudrate} " \
+ "mem=193M\0" \
+ "flash_nfs=run nfsargs addip addtty;" \
+ "bootm ${kernel_addr}\0" \
+ "flash_self=run ramargs addip addtty;" \
+ "bootm ${kernel_addr} ${ramdisk_addr}\0" \
+ "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \
+ "bootm\0" \
+ "net_nfs_fdt=tftp 200000 ${bootfile};" \
+ "tftp ${fdt_addr} ${fdt_file};" \
+ "run nfsargs addip addtty;" \
+ "bootm 200000 - ${fdt_addr}\0" \
+ "rootpath=/opt/projects/alpr/nfs_root\0" \
+ "bootfile=/alpr/uImage\0" \
+ "kernel_addr=fff00000\0" \
+ "ramdisk_addr=fff10000\0" \
+ "load=tftp 100000 /alpr/u-boot/u-boot.bin\0" \
+ "update=protect off fffc0000 ffffffff;era fffc0000 ffffffff;" \
+ "cp.b 100000 fffc0000 40000;" \
+ "setenv filesize;saveenv\0" \
+ "upd=run load update\0" \
+ "ethprime=ppc_4xx_eth3\0" \
+ "ethact=ppc_4xx_eth3\0" \
+ "autoload=no\0" \
+ "ipconfig=dhcp;setenv serverip 11.0.0.152\0" \
+ "load_fpga=fpga load 0 ffe00000 10dd9a\0" \
+ "mtdargs=setenv bootargs root=/dev/mtdblock6 rw " \
+ "rootfstype=jffs2 init=/sbin/init\0" \
+ "kernel1_mtd=nand read 200000 0 200000;run mtdargs addip addtty"\
+ ";bootm 200000\0" \
+ "kernel2_mtd=nand read 200000 200000 200000;run mtdargs addip " \
+ "addtty;bootm 200000\0" \
+ "kernel1=setenv actkernel 'kernel1';run load_fpga " \
+ "kernel1_mtd\0" \
+ "kernel2=setenv actkernel 'kernel2';run load_fpga " \
+ "kernel2_mtd\0" \
+ ""
+
+#define CONFIG_BOOTCOMMAND "run kernel2"
+
+#define CONFIG_BOOTDELAY 2 /* autoboot after 5 seconds */
+
+#define CONFIG_BAUDRATE 115200
+
+#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
+#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
+
+#define CONFIG_PPC4xx_EMAC
+#define CONFIG_MII 1 /* MII PHY management */
+#define CONFIG_PHY_ADDR 0x02 /* dummy setting, no EMAC0 used */
+#define CONFIG_PHY1_ADDR 0x03 /* dummy setting, no EMAC1 used */
+#define CONFIG_PHY2_ADDR 0x01 /* PHY address for EMAC2 */
+#define CONFIG_PHY3_ADDR 0x02 /* PHY address for EMAC3 */
+#define CONFIG_HAS_ETH0
+#define CONFIG_HAS_ETH1
+#define CONFIG_HAS_ETH2
+#define CONFIG_HAS_ETH3
+#define CONFIG_PHY_RESET 1 /* reset phy upon startup */
+#define CONFIG_M88E1111_PHY 1 /* needed for PHY specific setup*/
+#define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */
+#define CONFIG_SYS_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */
+
+#define CONFIG_NETCONSOLE /* include NetConsole support */
+
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_EEPROM
+#define CONFIG_CMD_FPGA
+#define CONFIG_CMD_I2C
+#undef CONFIG_CMD_LOADB
+#undef CONFIG_CMD_LOADS
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_NAND
+#define CONFIG_CMD_NET
+#undef CONFIG_CMD_NFS
+#define CONFIG_CMD_PCI
+
+#undef CONFIG_WATCHDOG /* watchdog disabled */
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#if defined(CONFIG_CMD_KGDB)
+#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
+#else
+#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
+#endif
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
+
+#define CONFIG_SYS_ALT_MEMTEST 1 /* Enable more extensive memtest*/
+#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */
+#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
+
+#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
+#define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_into (bd_t) */
+
+#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
+#define CONFIG_LOOPW 1 /* enable loopw command */
+#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */
+#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
+#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
+
+#define CONFIG_SYS_4xx_RESET_TYPE 0x2 /* use chip reset on this board */
+
+/*-----------------------------------------------------------------------
+ * PCI stuff
+ *-----------------------------------------------------------------------
+ */
+/* General PCI */
+#define CONFIG_PCI /* include pci support */
+#define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */
+#define CONFIG_PCI_PNP /* do pci plug-and-play */
+#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
+#define CONFIG_SYS_PCI_TARGBASE 0x80000000 /* PCIaddr mapped to CONFIG_SYS_PCI_MEMBASE */
+#define CONFIG_PCI_BOOTDELAY 1 /* enable pci bootdelay variable*/
+
+/* Board-specific PCI */
+#define CONFIG_SYS_PCI_TARGET_INIT /* let board init pci target */
+#define CONFIG_SYS_PCI_MASTER_INIT
+
+#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x10e8 /* AMCC */
+#define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0xcafe /* Whatever */
+
+/*-----------------------------------------------------------------------
+ * FPGA stuff
+ *-----------------------------------------------------------------------*/
+#define CONFIG_FPGA
+#define CONFIG_FPGA_ALTERA
+#define CONFIG_FPGA_CYCLON2
+#define CONFIG_SYS_FPGA_CHECK_CTRLC
+#define CONFIG_SYS_FPGA_PROG_FEEDBACK
+#define CONFIG_FPGA_COUNT 1 /* Ich habe 2 ... aber in
+ Reihe geschaltet -> sollte gehen,
+ aufpassen mit Datasize ist jetzt
+ halt doppelt so gross ... Seite 306
+ ist das mit den multiple Device in PS
+ Mode erklaert ...*/
+
+/* FPGA program pin configuration */
+#define CONFIG_SYS_GPIO_CLK 18 /* FPGA clk pin (cpu output) */
+#define CONFIG_SYS_GPIO_DATA 19 /* FPGA data pin (cpu output) */
+#define CONFIG_SYS_GPIO_STATUS 20 /* FPGA status pin (cpu input) */
+#define CONFIG_SYS_GPIO_CONFIG 21 /* FPGA CONFIG pin (cpu output) */
+#define CONFIG_SYS_GPIO_CON_DON 22 /* FPGA CONFIG_DONE pin (cpu input) */
+
+#define CONFIG_SYS_GPIO_SEL_DPR 14 /* cpu output */
+#define CONFIG_SYS_GPIO_SEL_AVR 15 /* cpu output */
+#define CONFIG_SYS_GPIO_PROG_EN 23 /* cpu output */
+
+/*-----------------------------------------------------------------------
+ * Definitions for GPIO setup
+ *-----------------------------------------------------------------------*/
+#define CONFIG_SYS_GPIO_SHUTDOWN (0x80000000 >> 6)
+#define CONFIG_SYS_GPIO_SSD_EMPTY (0x80000000 >> 9)
+#define CONFIG_SYS_GPIO_EREADY (0x80000000 >> 26)
+#define CONFIG_SYS_GPIO_REV0 (0x80000000 >> 14)
+#define CONFIG_SYS_GPIO_REV1 (0x80000000 >> 15)
+
+/*-----------------------------------------------------------------------
+ * NAND-FLASH stuff
+ *-----------------------------------------------------------------------*/
+#define CONFIG_SYS_MAX_NAND_DEVICE 4
+#define CONFIG_SYS_NAND_BASE 0xF0000000 /* NAND FLASH Base Address */
+#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE + 0, CONFIG_SYS_NAND_BASE + 2, \
+ CONFIG_SYS_NAND_BASE + 4, CONFIG_SYS_NAND_BASE + 6 }
+#define CONFIG_SYS_NAND_QUIET_TEST 1 /* don't warn upon unknown NAND flash */
+#define CONFIG_SYS_NAND_MAX_OOBFREE 2
+#define CONFIG_SYS_NAND_MAX_ECCPOS 56
+
+/*-----------------------------------------------------------------------
+ * External Bus Controller (EBC) Setup
+ *----------------------------------------------------------------------*/
+#define CONFIG_SYS_FLASH CONFIG_SYS_FLASH_BASE
+
+/* Memory Bank 0 (Flash Bank 0, NOR-FLASH) initialization */
+#define CONFIG_SYS_EBC_PB0AP 0x92015480
+#define CONFIG_SYS_EBC_PB0CR (CONFIG_SYS_FLASH | 0x3A000) /* BS=2MB,BU=R/W,BW=16bit */
+
+/* Memory Bank 1 (NAND-FLASH) initialization */
+#define CONFIG_SYS_EBC_PB1AP 0x01840380 /* TWT=3 */
+#define CONFIG_SYS_EBC_PB1CR (CONFIG_SYS_NAND_BASE | 0x18000) /* BS=1MB,BU=R/W,BW=8bit */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+
+#if defined(CONFIG_CMD_KGDB)
+#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
+#endif
+
+/* pass open firmware flat tree */
+#define CONFIG_OF_LIBFDT 1
+#define CONFIG_OF_BOARD_SETUP 1
+
+#endif /* __CONFIG_H */
Code Review / kvmfornfv.git / blobdiff