Add qemu 2.4.0

[kvmfornfv.git] / qemu / roms / u-boot / include / configs / afeb9260.h

diff --git a/qemu/roms/u-boot/include/configs/afeb9260.h b/qemu/roms/u-boot/include/configs/afeb9260.h
new file mode 100644 (file)
index 0000000..14bac15
--- /dev/null
+++ b/qemu/roms/u-boot/include/configs/afeb9260.h
@@ -0,0 +1,157 @@
+/*
+ * (C) Copyright 2008 Sergey Lapin <slapin@ossfans.org>
+ *
+ * Configuation settings for the AFEB9260 board.
+ * Based on configuration for AT91SAM9260-EK
+ *
+ * SPDX-License-Identifier:    GPL-2.0+
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+#define CONFIG_AT91SAM9260             /* Atmel AT91SAM9260 SoC*/
+#include <asm/arch/hardware.h>
+
+#define CONFIG_SYS_TEXT_BASE           0x21f00000
+
+/* ARM asynchronous clock */
+#define CONFIG_SYS_AT91_MAIN_CLOCK             18429952        /* from 18.432 MHz crystal */
+#define CONFIG_SYS_AT91_SLOW_CLOCK             32768
+
+#define CONFIG_BOARD_EARLY_INIT_F
+#define CONFIG_DISPLAY_CPUINFO
+
+#define CONFIG_AFEB9260                        /* AFEB9260 Board       */
+#define CONFIG_ARCH_CPU_INIT
+
+#define CONFIG_CMDLINE_TAG     1       /* enable passing of ATAGs      */
+#define CONFIG_SETUP_MEMORY_TAGS 1
+#define CONFIG_INITRD_TAG      1
+
+#define CONFIG_SKIP_LOWLEVEL_INIT
+
+/*
+ * Hardware drivers
+ */
+#define CONFIG_ATMEL_LEGACY
+#define CONFIG_AT91_GPIO
+#define CONFIG_AT91_PULLUP     1
+
+#define CONFIG_ATMEL_USART
+#define CONFIG_USART_BASE      ATMEL_BASE_DBGU
+#define CONFIG_USART_ID                ATMEL_ID_SYS
+#define CONFIG_USART3          /* USART 3 is DBGU */
+
+#define CONFIG_BOOTDELAY       3
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE      1
+#define CONFIG_BOOTP_BOOTPATH          1
+#define CONFIG_BOOTP_GATEWAY           1
+#define CONFIG_BOOTP_HOSTNAME          1
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+#undef CONFIG_CMD_BDI
+#undef CONFIG_CMD_FPGA
+#undef CONFIG_CMD_IMI
+#undef CONFIG_CMD_IMLS
+#undef CONFIG_CMD_LOADS
+#undef CONFIG_CMD_SOURCE
+
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_DHCP
+
+#define CONFIG_CMD_NAND
+#define CONFIG_CMD_USB
+
+/* SDRAM */
+#define CONFIG_NR_DRAM_BANKS           1
+#define CONFIG_SYS_SDRAM_BASE          ATMEL_BASE_CS1
+#define CONFIG_SYS_SDRAM_SIZE          0x04000000      /* 64 megs */
+
+/* DataFlash */
+#define CONFIG_ATMEL_DATAFLASH_SPI
+#define CONFIG_HAS_DATAFLASH
+#define CONFIG_SYS_SPI_WRITE_TOUT              (5 * CONFIG_SYS_HZ)
+#define CONFIG_SYS_MAX_DATAFLASH_BANKS         2
+#define CONFIG_SYS_DATAFLASH_LOGIC_ADDR_CS0    0xC0000000      /* CS0 */
+#define CONFIG_SYS_DATAFLASH_LOGIC_ADDR_CS1    0xD0000000      /* CS1 */
+#define AT91_SPI_CLK                   15000000
+#define DATAFLASH_TCSS                 (0x1a << 16)
+#define DATAFLASH_TCHS                 (0x1 << 24)
+
+/* NAND flash */
+#ifdef CONFIG_CMD_NAND
+#define CONFIG_NAND_ATMEL
+#define CONFIG_SYS_MAX_NAND_DEVICE             1
+#define CONFIG_SYS_NAND_BASE                   ATMEL_BASE_CS3
+#define CONFIG_SYS_NAND_DBW_8
+/* our ALE is AD21 */
+#define CONFIG_SYS_NAND_MASK_ALE               (1 << 21)
+/* our CLE is AD22 */
+#define CONFIG_SYS_NAND_MASK_CLE               (1 << 22)
+#define CONFIG_SYS_NAND_ENABLE_PIN             AT91_PIN_PC14
+#define CONFIG_SYS_NAND_READY_PIN              AT91_PIN_PC13
+
+#endif
+
+/* NOR flash - no real flash on this board */
+#define CONFIG_SYS_NO_FLASH
+
+/* Ethernet */
+#define CONFIG_MACB
+#define CONFIG_RESET_PHY_R
+#define CONFIG_AT91_WANTS_COMMON_PHY
+#define CONFIG_NET_RETRY_COUNT         20
+
+/* USB */
+#define CONFIG_USB_ATMEL
+#define CONFIG_USB_ATMEL_CLK_SEL_PLLB
+#define CONFIG_USB_OHCI_NEW
+#define CONFIG_DOS_PARTITION
+#define CONFIG_SYS_USB_OHCI_CPU_INIT
+#define CONFIG_SYS_USB_OHCI_REGS_BASE          0x00500000      /* AT91SAM9260_UHP_BASE */
+#define CONFIG_SYS_USB_OHCI_SLOT_NAME          "at91sam9260"
+#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS     1
+#define CONFIG_USB_STORAGE
+
+#define CONFIG_SYS_LOAD_ADDR                   0x21000000      /* load address */
+
+#define CONFIG_SYS_MEMTEST_START               CONFIG_SYS_SDRAM_BASE
+#define CONFIG_SYS_MEMTEST_END                 0x21e00000
+
+#define CONFIG_SYS_USE_DATAFLASH_CS1
+#define CONFIG_SYS_INIT_SP_ADDR                (ATMEL_BASE_SRAM1 + 0x1000 -\
+                                       GENERATED_GBL_DATA_SIZE)
+
+/* bootstrap + u-boot + env + linux in dataflash on CS1 */
+#define CONFIG_ENV_IS_IN_DATAFLASH
+#define CONFIG_SYS_MONITOR_BASE        (CONFIG_SYS_DATAFLASH_LOGIC_ADDR_CS1 + 0x8400)
+#define CONFIG_ENV_OFFSET              0x4200
+#define CONFIG_ENV_ADDR                (CONFIG_SYS_DATAFLASH_LOGIC_ADDR_CS1 + CONFIG_ENV_OFFSET)
+#define CONFIG_ENV_SIZE                0x4200
+#define CONFIG_BOOTCOMMAND     "nand read 0x21000000 0xa0000 0x200000; bootm"
+#define CONFIG_BOOTARGS                "console=ttyS0,115200 "                 \
+                               "root=/dev/mtdblock2 "                  \
+                               "rw rootfstype=jffs2 panic=20"
+
+#define CONFIG_BAUDRATE                115200
+
+#define CONFIG_SYS_PROMPT              "U-Boot> "
+#define CONFIG_SYS_CBSIZE              256
+#define CONFIG_SYS_MAXARGS             16
+#define CONFIG_SYS_PBSIZE              (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
+#define CONFIG_SYS_LONGHELP
+#define CONFIG_CMDLINE_EDITING
+
+/*
+ * Size of malloc() pool
+ */
+#define CONFIG_SYS_MALLOC_LEN          ROUND(3 * CONFIG_ENV_SIZE + 128*1024, 0x1000)
+
+#endif