--- /dev/null
+/*
+ * (C) Copyright 2004
+ * Elmeg Communications Systems GmbH, Juergen Selent (j.selent@elmeg.de)
+ *
+ * Support for the Elmeg VoVPN Gateway Module
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/* define cpu used */
+#define CONFIG_MPC8272 1
+
+/* define busmode: 8260 */
+#undef CONFIG_BUSMODE_60x
+
+#define CONFIG_SYS_TEXT_BASE 0xfff00000
+
+/* system clock rate (CLKIN) - equal to the 60x and local bus speed */
+#ifdef CONFIG_CLKIN_66MHz
+#define CONFIG_8260_CLKIN 66666666 /* in Hz */
+#else
+#define CONFIG_8260_CLKIN 100000000 /* in Hz */
+#endif
+
+/* call board_early_init_f */
+#define CONFIG_BOARD_EARLY_INIT_F 1
+
+/* have misc_init_r() function */
+#define CONFIG_MISC_INIT_R 1
+
+/* have reset_phy_r() function */
+#define CONFIG_RESET_PHY_R 1
+
+/* have special reset function */
+#define CONFIG_HAVE_OWN_RESET 1
+
+/* allow serial and ethaddr to be overwritten */
+#define CONFIG_ENV_OVERWRITE
+
+/* watchdog disabled */
+#undef CONFIG_WATCHDOG
+
+/* include support for bzip2 compressed images */
+#undef CONFIG_BZIP2
+
+/* status led */
+#undef CONFIG_STATUS_LED /* XXX jse */
+
+/* vendor parameter protection */
+#define CONFIG_ENV_OVERWRITE
+
+/*
+ * select serial console configuration
+ *
+ * if either CONFIG_CONS_ON_SMC or CONFIG_CONS_ON_SCC is selected, then
+ * CONFIG_CONS_INDEX must be set to the channel number (1-2 for SMC, 1-4
+ * for SCC).
+ */
+#define CONFIG_CONS_ON_SMC
+#undef CONFIG_CONS_ON_SCC
+#undef CONFIG_CONS_NONE
+#define CONFIG_CONS_INDEX 1
+
+/* serial port default baudrate */
+#define CONFIG_BAUDRATE 115200
+
+/* echo on for serial download */
+#define CONFIG_LOADS_ECHO 1
+
+/* don't allow baudrate change */
+#undef CONFIG_SYS_LOADS_BAUD_CHANGE
+
+/*
+ * select ethernet configuration
+ *
+ * if either CONFIG_ETHER_ON_SCC or CONFIG_ETHER_ON_FCC is selected, then
+ * CONFIG_ETHER_INDEX must be set to the channel number (1-4 for SCC, 1-3
+ * for FCC)
+ *
+ * if CONFIG_ETHER_NONE is defined, then either the ethernet routines must be
+ * defined elsewhere (as for the console), or CONFIG_CMD_NET must be unset.
+ */
+#undef CONFIG_ETHER_ON_SCC
+#define CONFIG_ETHER_ON_FCC
+#undef CONFIG_ETHER_NONE
+
+#ifdef CONFIG_ETHER_ON_FCC
+
+/* which SCC/FCC channel for ethernet */
+#define CONFIG_ETHER_INDEX 1
+
+/* Marvell Switch SMI base addr */
+#define CONFIG_SYS_PHY_ADDR 0x10
+
+/* FCC1 RMII REFCLK is CLK10 */
+#define CONFIG_SYS_CMXFCR_VALUE CMXFCR_TF1CS_CLK10
+#define CONFIG_SYS_CMXFCR_MASK (CMXFCR_FC1|CMXFCR_TF1CS_MSK)
+
+/* BDs and buffers on 60x bus */
+#define CONFIG_SYS_CPMFCR_RAMTYPE 0
+
+/* Local Protect, Full duplex, Flowcontrol, RMII */
+#define CONFIG_SYS_FCC_PSMR (FCC_PSMR_LPB|FCC_PSMR_FDE|\
+ FCC_PSMR_FCE|FCC_PSMR_RMII)
+
+/* bit-bang MII PHY management */
+#define CONFIG_BITBANGMII
+
+#define MDIO_PORT 1 /* Port B */
+
+#define MDIO_DECLARE volatile ioport_t *iop = ioport_addr ( \
+ (immap_t *) CONFIG_SYS_IMMR, MDIO_PORT )
+#define MDC_DECLARE MDIO_DECLARE
+
+#define CONFIG_SYS_MDIO_PIN 0x00002000 /* PB18 */
+#define CONFIG_SYS_MDC_PIN 0x00001000 /* PB19 */
+#define MDIO_ACTIVE (iop->pdir |= CONFIG_SYS_MDIO_PIN)
+#define MDIO_TRISTATE (iop->pdir &= ~CONFIG_SYS_MDIO_PIN)
+#define MDIO_READ ((iop->pdat & CONFIG_SYS_MDIO_PIN) != 0)
+#define MDIO(bit) if(bit) iop->pdat |= CONFIG_SYS_MDIO_PIN; \
+ else iop->pdat &= ~CONFIG_SYS_MDIO_PIN
+#define MDC(bit) if(bit) iop->pdat |= CONFIG_SYS_MDC_PIN; \
+ else iop->pdat &= ~CONFIG_SYS_MDC_PIN
+#define MIIDELAY udelay(1)
+
+#endif
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+
+/*
+ * Command line configuration.
+ */
+
+#define CONFIG_CMD_BDI
+#define CONFIG_CMD_CONSOLE
+#define CONFIG_CMD_ECHO
+#define CONFIG_CMD_FLASH
+#define CONFIG_CMD_IMI
+#define CONFIG_CMD_IMLS
+#define CONFIG_CMD_LOADB
+#define CONFIG_CMD_MEMORY
+#define CONFIG_CMD_MISC
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_RUN
+#define CONFIG_CMD_SAVEENV
+#define CONFIG_CMD_SOURCE
+
+
+/*
+ * boot options & environment
+ */
+#define CONFIG_BOOTDELAY 3
+#define CONFIG_BOOTCOMMAND "run flash_self"
+#undef CONFIG_BOOTARGS
+#define CONFIG_EXTRA_ENV_SETTINGS \
+"clean_nv=erase fff20000 ffffffff\0" \
+"update_boss=tftp 100000 PPC/logic157.bin; protect off fff00000 ffffffff; erase fff00000 ffffffff; cp.b 100000 fff00000 ${filesize}; tftp 100000 PPC/bootmon157.bin; cp.b 100000 fff20000 ${filesize}\0" \
+"update_lx=tftp 100000 ${kernel}; erase ${kernel_addr} ffefffff; cp.b 100000 ${kernel_addr} ${filesize}\0" \
+"update_fs=tftp 100000 ${fs}.${fstype}; erase ff840000 ffdfffff; cp.b 100000 ff840000 ${filesize}\0" \
+"update_ub=tftp 100000 ${uboot}; protect off fff00000 fff1ffff; erase fff00000 fff1ffff; cp.b 100000 fff00000 ${filesize}; protect off ff820000 ff83ffff; erase ff820000 ff83ffff\0" \
+"flashargs=setenv bootargs root=${rootdev} rw rootfstype=${fstype}\0" \
+"nfsargs=setenv bootargs root=/dev/nfs rw nfsroot=${serverip}:${rootpath}\0" \
+"addip=setenv bootargs ${bootargs} ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}:${netdev}:off\0" \
+"addmisc=setenv bootargs ${bootargs} console=${console},${baudrate} ethaddr=${ethaddr} panic=1\0" \
+"net_nfs=tftpboot 400000 ${kernel}; run nfsargs addip addmisc; bootm\0" \
+"net_self=tftpboot 400000 ${kernel}; run flashargs addmisc; bootm\0" \
+"flash_self=run flashargs addmisc; bootm ${kernel_addr}\0" \
+"flash_nfs=run nfsargs addip addmisc; bootm ${kernel_addr}\0" \
+"fstype=cramfs\0" \
+"rootpath=/root_fs\0" \
+"uboot=PPC/u-boot.bin\0" \
+"kernel=PPC/uImage\0" \
+"kernel_addr=ffe00000\0" \
+"fs=PPC/root_fs\0" \
+"console=ttyS0\0" \
+"netdev=eth0\0" \
+"rootdev=31:3\0" \
+"ethaddr=00:09:4f:01:02:03\0" \
+"ipaddr=10.0.0.201\0" \
+"netmask=255.255.255.0\0" \
+"serverip=10.0.0.136\0" \
+"gatewayip=10.0.0.10\0" \
+"hostname=bastard\0" \
+""
+
+
+/*
+ * miscellaneous configurable options
+ */
+
+/* undef to save memory */
+#define CONFIG_SYS_LONGHELP
+
+/* monitor command prompt */
+
+/* console i/o buffer size */
+#if defined(CONFIG_CMD_KGDB)
+#define CONFIG_SYS_CBSIZE 1024
+#else
+#define CONFIG_SYS_CBSIZE 256
+#endif
+
+/* print buffer size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
+
+/* max number of command args */
+#define CONFIG_SYS_MAXARGS 16
+
+/* boot argument buffer size */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
+
+/* memtest works on */
+#define CONFIG_SYS_MEMTEST_START 0x00100000
+/* 1 ... 15 MB in DRAM */
+#define CONFIG_SYS_MEMTEST_END 0x00f00000
+/* full featured memtest */
+#define CONFIG_SYS_ALT_MEMTEST
+
+/* default load address */
+#define CONFIG_SYS_LOAD_ADDR 0x00100000
+
+/* decrementer freq: 1 ms ticks */
+
+/* configure flash */
+#define CONFIG_SYS_FLASH_BASE 0xff800000
+#define CONFIG_SYS_MAX_FLASH_BANKS 1
+#define CONFIG_SYS_MAX_FLASH_SECT 64
+#define CONFIG_SYS_FLASH_SIZE 8
+#undef CONFIG_SYS_FLASH_16BIT
+#define CONFIG_SYS_FLASH_ERASE_TOUT 240000
+#define CONFIG_SYS_FLASH_WRITE_TOUT 500
+#define CONFIG_SYS_FLASH_LOCK_TOUT 500
+#define CONFIG_SYS_FLASH_UNLOCK_TOUT 10000
+#define CONFIG_SYS_FLASH_PROTECTION
+
+/* monitor in flash */
+#define CONFIG_SYS_MONITOR_OFFSET 0x00700000
+
+/* environment in flash */
+#define CONFIG_ENV_IS_IN_FLASH 1
+#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x00020000)
+#define CONFIG_ENV_SIZE 0x00020000
+#define CONFIG_ENV_SECT_SIZE 0x00020000
+
+/*
+ * Initial memory map for linux
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_SYS_BOOTMAPSZ (8 << 20)
+
+/* hard reset configuration words */
+#ifdef CONFIG_CLKIN_66MHz
+#define CONFIG_SYS_HRCW_MASTER 0x04643050
+#else
+#error NO HRCW FOR 100MHZ SPECIFIED !!!
+#endif
+#define CONFIG_SYS_HRCW_SLAVE1 0x00000000
+#define CONFIG_SYS_HRCW_SLAVE2 0x00000000
+#define CONFIG_SYS_HRCW_SLAVE3 0x00000000
+#define CONFIG_SYS_HRCW_SLAVE4 0x00000000
+#define CONFIG_SYS_HRCW_SLAVE5 0x00000000
+#define CONFIG_SYS_HRCW_SLAVE6 0x00000000
+#define CONFIG_SYS_HRCW_SLAVE7 0x00000000
+
+/* internal memory mapped register */
+#define CONFIG_SYS_IMMR 0xF0000000
+
+/* definitions for initial stack pointer and data area (in DPRAM) */
+#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR
+#define CONFIG_SYS_INIT_RAM_SIZE 0x2000
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
+
+/*
+ * Start addresses for the final memory configuration
+ * (Set up by the startup code)
+ * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
+ */
+#define CONFIG_SYS_SDRAM_BASE 0x00000000
+#define CONFIG_SYS_SDRAM_SIZE (32*1024*1024)
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
+#define CONFIG_SYS_MONITOR_FLASH (CONFIG_SYS_FLASH_BASE + CONFIG_SYS_MONITOR_OFFSET)
+#define CONFIG_SYS_MONITOR_LEN 0x00020000
+#define CONFIG_SYS_MALLOC_LEN 0x00020000
+
+/* cache configuration */
+#define CONFIG_SYS_CACHELINE_SIZE 32 /* for MPC8260 */
+#if defined(CONFIG_CMD_KGDB)
+#define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of above */
+#endif
+
+/*
+ * HIDx - Hardware Implementation-dependent Registers
+ *-----------------------------------------------------------------------
+ * HID0 also contains cache control - initially enable both caches and
+ * invalidate contents, then the final state leaves only the instruction
+ * cache enabled. Note that Power-On and Hard reset invalidate the caches,
+ * but Soft reset does not.
+ *
+ * HID1 has only read-only information - nothing to set.
+ */
+#define CONFIG_SYS_HID0_INIT (HID0_ICE|HID0_DCE|\
+ HID0_ICFI|HID0_DCI|HID0_IFEM|HID0_ABE)
+#define CONFIG_SYS_HID0_FINAL (HID0_IFEM|HID0_ABE)
+#define CONFIG_SYS_HID2 0
+
+/* RMR - reset mode register - turn on checkstop reset enable */
+#define CONFIG_SYS_RMR RMR_CSRE
+
+/* BCR - bus configuration */
+#define CONFIG_SYS_BCR 0x00000000
+
+/* SIUMCR - siu module configuration */
+#define CONFIG_SYS_SIUMCR 0x4905c000
+
+/* SYPCR - system protection control */
+#if defined(CONFIG_WATCHDOG)
+#define CONFIG_SYS_SYPCR 0xffffff87
+#else
+#define CONFIG_SYS_SYPCR 0xffffff83
+#endif
+
+/* TMCNTSC - time counter status and control */
+/* clear interrupts XXX jse */
+/*#define CONFIG_SYS_TMCNTSC (TMCNTSC_SEC|TMCNTSC_ALR) */
+#define CONFIG_SYS_TMCNTSC (TMCNTSC_SEC|TMCNTSC_ALR|\
+ TMCNTSC_TCF|TMCNTSC_TCE)
+
+/* PISCR - periodic interrupt status and control */
+/* clear interrupts XXX jse */
+/*#define CONFIG_SYS_PISCR (PISCR_PS) */
+#define CONFIG_SYS_PISCR (PISCR_PS|PISCR_PTF|PISCR_PTE)
+
+/* SCCR - system clock control */
+#define CONFIG_SYS_SCCR 0x000001a9
+
+/* RCCR - risc controller configuration */
+#define CONFIG_SYS_RCCR 0
+
+/*
+ * MEMORY MAP
+ * ----------
+ * CS0 - FLASH 8MB/8Bit base=0xff800000 (boot: 0xfe000000, 8x mirrored)
+ * CS1 - SDRAM 32MB/64Bit base=0x00000000
+ * CS2 - DSP/SL1 1MB/16Bit base=0xf0100000
+ * CS3 - DSP/SL2 1MB/16Bit base=0xf0200000
+ * CS4 - DSP/SL3 1MB/16Bit base=0xf0300000
+ * CS5 - DSP/SL4 1MB/16Bit base=0xf0400000
+ * CS7 - DPRAM 1KB/8Bit base=0xf0500000, size=32KB (32x mirrored)
+ * x - IMMR 384KB base=0xf0000000
+ */
+/* XXX jse 100MHz TODO */
+#define CONFIG_SYS_BR0_PRELIM 0xff800801
+#define CONFIG_SYS_OR0_PRELIM 0xff801e44
+#define CONFIG_SYS_BR1_PRELIM 0x00000041
+#define CONFIG_SYS_OR1_PRELIM 0xfe002ec0
+#if 1
+#define CONFIG_SYS_BR2_PRELIM 0xf0101001
+#define CONFIG_SYS_OR2_PRELIM 0xfff00ef4
+#define CONFIG_SYS_BR3_PRELIM 0xf0201001
+#define CONFIG_SYS_OR3_PRELIM 0xfff00ef4
+#define CONFIG_SYS_BR4_PRELIM 0xf0301001
+#define CONFIG_SYS_OR4_PRELIM 0xfff00ef4
+#define CONFIG_SYS_BR5_PRELIM 0xf0401001
+#define CONFIG_SYS_OR5_PRELIM 0xfff00ef4
+#else
+#define CONFIG_SYS_BR2_PRELIM 0xf0101081
+#define CONFIG_SYS_OR2_PRELIM 0xfff00104
+#define CONFIG_SYS_BR3_PRELIM 0xf0201081
+#define CONFIG_SYS_OR3_PRELIM 0xfff00104
+#define CONFIG_SYS_BR4_PRELIM 0xf0301081
+#define CONFIG_SYS_OR4_PRELIM 0xfff00104
+#define CONFIG_SYS_BR5_PRELIM 0xf0401081
+#define CONFIG_SYS_OR5_PRELIM 0xfff00104
+#endif
+#define CONFIG_SYS_BR7_PRELIM 0xf0500881
+#define CONFIG_SYS_OR7_PRELIM 0xffff8104
+#define CONFIG_SYS_MPTPR 0x2700
+#define CONFIG_SYS_PSDMR 0x822a2452 /* optimal */
+/*#define CONFIG_SYS_PSDMR 0x822a48a3 */ /* relaxed */
+#define CONFIG_SYS_PSRT 0x1a
+
+/* "bad" address */
+#define CONFIG_SYS_RESET_ADDRESS 0x40000000
+
+#endif /* __CONFIG_H */
Code Review / kvmfornfv.git / blobdiff