--- /dev/null
+/*
+ * (C) Copyright 2003-2006
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * (C) Copyright 2004-2006
+ * Martin Krause, TQ-Systems GmbH, martin.krause@tqs.de
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+
+#define CONFIG_MPC5200 1 /* This is an MPC5200 CPU */
+#define CONFIG_TQM5200 1 /* ... on TQM5200 module */
+#define CONFIG_TB5200 1 /* ... on a TB5200 base board */
+
+/*
+ * Valid values for CONFIG_SYS_TEXT_BASE are:
+ * 0xFC000000 boot low (standard configuration with room for
+ * max 64 MByte Flash ROM)
+ * 0xFFF00000 boot high (for a backup copy of U-Boot)
+ * 0x00100000 boot from RAM (for testing only)
+ */
+#ifndef CONFIG_SYS_TEXT_BASE
+#define CONFIG_SYS_TEXT_BASE 0xFC000000
+#endif
+
+#define CONFIG_SYS_MPC5XXX_CLKIN 33000000 /* ... running at 33.000000MHz */
+
+#define CONFIG_HIGH_BATS 1 /* High BATs supported */
+
+/*
+ * Serial console configuration
+ */
+#define CONFIG_PSC_CONSOLE 1 /* default console is on PSC1 */
+#define CONFIG_PSC_CONSOLE2 6 /* second console is on PSC6 */
+#define CONFIG_BAUDRATE 115200 /* ... at 115200 bps */
+#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 }
+
+/*
+ * Video console
+ */
+#if 1
+#define CONFIG_VIDEO
+#define CONFIG_VIDEO_SM501
+#define CONFIG_VIDEO_SM501_32BPP
+#define CONFIG_CFB_CONSOLE
+#define CONFIG_VIDEO_LOGO
+#define CONFIG_VGA_AS_SINGLE_DEVICE
+#define CONFIG_CONSOLE_EXTRA_INFO
+#define CONFIG_VIDEO_SW_CURSOR
+#define CONFIG_SPLASH_SCREEN
+#define CONFIG_SYS_CONSOLE_IS_IN_ENV
+#endif
+
+/* Partitions */
+#define CONFIG_MAC_PARTITION
+#define CONFIG_DOS_PARTITION
+#define CONFIG_ISO_PARTITION
+
+/* USB */
+#define CONFIG_USB_OHCI
+#define CONFIG_USB_STORAGE
+
+/* POST support */
+#define CONFIG_POST (CONFIG_SYS_POST_MEMORY | \
+ CONFIG_SYS_POST_CPU | \
+ CONFIG_SYS_POST_I2C)
+
+#ifdef CONFIG_POST
+/* preserve space for the post_word at end of on-chip SRAM */
+#define MPC5XXX_SRAM_POST_SIZE MPC5XXX_SRAM_SIZE-4
+#endif
+
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_ASKENV
+#define CONFIG_CMD_DATE
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_ECHO
+#define CONFIG_CMD_EEPROM
+#define CONFIG_CMD_EXT2
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_IDE
+#define CONFIG_CMD_JFFS2
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_NFS
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_REGINFO
+#define CONFIG_CMD_SNTP
+#define CONFIG_CMD_BSP
+#define CONFIG_CMD_USB
+
+#ifdef CONFIG_VIDEO
+#define CONFIG_CMD_BMP
+#endif
+
+#ifdef CONFIG_POST
+#define CONFIG_CMD_DIAG
+#endif
+
+
+#define CONFIG_TIMESTAMP /* display image timestamps */
+
+#if (CONFIG_SYS_TEXT_BASE == 0xFC000000) /* Boot low */
+# define CONFIG_SYS_LOWBOOT 1
+#endif
+
+/*
+ * Autobooting
+ */
+#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
+
+#define CONFIG_PREBOOT "echo;" \
+ "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
+ "echo"
+
+#undef CONFIG_BOOTARGS
+
+#if defined(CONFIG_TQM5200_B)
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "netdev=eth0\0" \
+ "rootpath=/opt/eldk/ppc_6xx\0" \
+ "ramargs=setenv bootargs root=/dev/ram rw\0" \
+ "nfsargs=setenv bootargs root=/dev/nfs rw " \
+ "nfsroot=${serverip}:${rootpath}\0" \
+ "addip=setenv bootargs ${bootargs} " \
+ "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
+ ":${hostname}:${netdev}:off panic=1\0" \
+ "flash_self=run ramargs addip;" \
+ "bootm ${kernel_addr} ${ramdisk_addr}\0" \
+ "flash_nfs=run nfsargs addip;" \
+ "bootm ${kernel_addr}\0" \
+ "net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0" \
+ "bootfile=/tftpboot/tqm5200/uImage\0" \
+ "load=tftp 200000 ${u-boot}\0" \
+ "u-boot=/tftpboot/tqm5200/u-boot.bin\0" \
+ "update=protect off FC000000 FC07FFFF;" \
+ "erase FC000000 FC07FFFF;" \
+ "cp.b 200000 FC000000 ${filesize};" \
+ "protect on FC000000 FC07FFFF\0" \
+ ""
+#else
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "netdev=eth0\0" \
+ "rootpath=/opt/eldk/ppc_6xx\0" \
+ "ramargs=setenv bootargs root=/dev/ram rw\0" \
+ "nfsargs=setenv bootargs root=/dev/nfs rw " \
+ "nfsroot=${serverip}:${rootpath}\0" \
+ "addip=setenv bootargs ${bootargs} " \
+ "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
+ ":${hostname}:${netdev}:off panic=1\0" \
+ "flash_self=run ramargs addip;" \
+ "bootm ${kernel_addr} ${ramdisk_addr}\0" \
+ "flash_nfs=run nfsargs addip;" \
+ "bootm ${kernel_addr}\0" \
+ "net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0" \
+ "bootfile=/tftpboot/tqm5200/uImage\0" \
+ "load=tftp 200000 $(u-boot)\0" \
+ "u-boot=/tftpboot/tqm5200/u-boot.bin\0" \
+ "update=protect off FC000000 FC05FFFF;" \
+ "erase FC000000 FC05FFFF;" \
+ "cp.b 200000 FC000000 ${filesize};" \
+ "protect on FC000000 FC05FFFF\0" \
+ ""
+#endif /* CONFIG_TQM5200_B */
+
+#define CONFIG_BOOTCOMMAND "run net_nfs"
+
+/*
+ * IPB Bus clocking configuration.
+ */
+#define CONFIG_SYS_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */
+
+#if defined(CONFIG_SYS_IPBCLK_EQUALS_XLBCLK)
+/*
+ * PCI Bus clocking configuration
+ *
+ * Actually a PCI Clock of 66 MHz is only set (in cpu_init.c) if
+ * CONFIG_SYS_IPBCLK_EQUALS_XLBCLK is defined. This is because a PCI Clock
+ * of 66 MHz yet hasn't been tested with a IPB Bus Clock of 66 MHz.
+ */
+#define CONFIG_SYS_PCICLK_EQUALS_IPBCLK_DIV2 /* define for 66MHz speed */
+#endif
+
+/*
+ * I2C configuration
+ */
+#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
+#define CONFIG_SYS_I2C_MODULE 2 /* Select I2C module #2 */
+
+/*
+ * I2C clock frequency
+ *
+ * Please notice, that the resulting clock frequency could differ from the
+ * configured value. This is because the I2C clock is derived from system
+ * clock over a frequency divider with only a few divider values. U-boot
+ * calculates the best approximation for CONFIG_SYS_I2C_SPEED. However the calculated
+ * approximation allways lies below the configured value, never above.
+ */
+#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */
+#define CONFIG_SYS_I2C_SLAVE 0x7F
+
+/*
+ * EEPROM configuration for onboard EEPROM M24C32 (M24C64 should work
+ * also). For other EEPROMs configuration should be verified. On Mini-FAP the
+ * EEPROM (24C64) is on the same I2C address (but on other I2C bus), so the
+ * same configuration could be used.
+ */
+#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* 1010000x */
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5 /* =32 Bytes per write */
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 20
+
+/* List of I2C addresses to be verified by POST */
+#undef CONFIG_SYS_POST_I2C_ADDRS
+#define CONFIG_SYS_POST_I2C_ADDRS {CONFIG_SYS_I2C_EEPROM_ADDR, \
+ CONFIG_SYS_I2C_RTC_ADDR, \
+ CONFIG_SYS_I2C_SLAVE}
+
+/*
+ * Flash configuration
+ */
+#define CONFIG_SYS_FLASH_BASE CONFIG_SYS_TEXT_BASE /* 0xFC000000 */
+
+/* use CFI flash driver */
+#define CONFIG_SYS_FLASH_CFI 1 /* Flash is CFI conformant */
+#define CONFIG_FLASH_CFI_DRIVER 1 /* Use the common driver */
+#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_BOOTCS_START }
+#define CONFIG_SYS_FLASH_EMPTY_INFO
+#define CONFIG_SYS_FLASH_SIZE 0x04000000 /* 64 MByte */
+#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max num of sects on one chip */
+#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1
+
+#if !defined(CONFIG_SYS_LOWBOOT)
+#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x00760000 + 0x00800000)
+#else /* CONFIG_SYS_LOWBOOT */
+#if defined(CONFIG_TQM5200_B)
+#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x00080000)
+#else
+#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x00060000)
+#endif /* CONFIG_TQM5200_B */
+#endif /* CONFIG_SYS_LOWBOOT */
+#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of flash banks
+ (= chip selects) */
+
+/* Dynamic MTD partition support */
+#define CONFIG_CMD_MTDPARTS
+#define CONFIG_MTD_DEVICE /* needed for mtdparts commands */
+#define CONFIG_FLASH_CFI_MTD
+#define MTDIDS_DEFAULT "nor0=TQM5200-0"
+#if defined(CONFIG_TQM5200_B)
+#define MTDPARTS_DEFAULT "mtdparts=TQM5200-0:768k(firmware)," \
+ "1280k(kernel)," \
+ "2m(initrd)," \
+ "4m(small-fs)," \
+ "16m(big-fs)," \
+ "8m(misc)"
+#else
+#define MTDPARTS_DEFAULT "mtdparts=TQM5200-0:640k(firmware)," \
+ "1408k(kernel)," \
+ "2m(initrd)," \
+ "4m(small-fs)," \
+ "16m(big-fs)," \
+ "8m(misc)"
+#endif /* CONFIG_TQM5200_B */
+
+/*
+ * Environment settings
+ */
+#define CONFIG_ENV_IS_IN_FLASH 1
+#define CONFIG_ENV_SIZE 0x10000
+#if defined(CONFIG_TQM5200_B)
+#define CONFIG_ENV_SECT_SIZE 0x40000
+#else
+#define CONFIG_ENV_SECT_SIZE 0x20000
+#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
+#endif /* CONFIG_TQM5200_B */
+
+/*
+ * Memory map
+ */
+#define CONFIG_SYS_MBAR 0xF0000000
+#define CONFIG_SYS_SDRAM_BASE 0x00000000
+#define CONFIG_SYS_DEFAULT_MBAR 0x80000000
+
+/* Use ON-Chip SRAM until RAM will be available */
+#define CONFIG_SYS_INIT_RAM_ADDR MPC5XXX_SRAM
+#ifdef CONFIG_POST
+/* preserve space for the post_word at end of on-chip SRAM */
+#define CONFIG_SYS_INIT_RAM_SIZE MPC5XXX_SRAM_POST_SIZE
+#else
+#define CONFIG_SYS_INIT_RAM_SIZE MPC5XXX_SRAM_SIZE
+#endif
+
+
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
+
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
+#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
+# define CONFIG_SYS_RAMBOOT 1
+#endif
+
+#if defined(CONFIG_TQM5200_B)
+#define CONFIG_SYS_MONITOR_LEN (512 << 10) /* Reserve 512 kB for Monitor */
+#else
+#define CONFIG_SYS_MONITOR_LEN (384 << 10) /* Reserve 384 kB for Monitor */
+#endif /* CONFIG_TQM5200_B */
+#define CONFIG_SYS_MALLOC_LEN (1024 << 10) /* Reserve 1024 kB for malloc() */
+#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+
+/*
+ * Ethernet configuration
+ */
+#define CONFIG_MPC5xxx_FEC 1
+#define CONFIG_MPC5xxx_FEC_MII100
+/*
+ * Define CONFIG_MPC5xxx_FEC_MII10 to force FEC at 10Mb
+ */
+/* #define CONFIG_MPC5xxx_FEC_MII10 */
+#define CONFIG_PHY_ADDR 0x00
+
+/*
+ * GPIO configuration
+ *
+ * use pin gpio_wkup_6 as second SDRAM chip select (mem_cs1):
+ * Bit 0 (mask: 0x80000000): 1
+ * use ALT CAN position: Bits 2-3 (mask: 0x30000000):
+ * 00 -> No Alternatives, CAN1/2 on PSC2 according to PSC2 setting.
+ * 01 -> CAN1 on I2C1, CAN2 on Tmr0/1.
+ * Use for REV200 STK52XX boards. Do not use with REV100 modules
+ * (because, there I2C1 is used as I2C bus)
+ * use PSC1 as UART: Bits 28-31 (mask: 0x00000007): 0100
+ * use PSC2 as CAN: Bits 25:27 (mask: 0x00000030)
+ * 000 -> All PSC2 pins are GIOPs
+ * 001 -> CAN1/2 on PSC2 pins
+ * Use for REV100 STK52xx boards
+ * use PSC3: Bits 20:23 (mask: 0x00000300):
+ * 0001 -> USB2
+ * 0000 -> GPIO
+ * use PSC6:
+ * on STK52xx:
+ * use as UART. Pins PSC6_0 to PSC6_3 are used.
+ * Bits 9:11 (mask: 0x00700000):
+ * 101 -> PSC6 : Extended POST test is not available
+ * on MINI-FAP and TQM5200_IB:
+ * use PSC6_0 to PSC6_3 as GPIO: Bits 9:11 (mask: 0x00700000):
+ * 000 -> PSC6 could not be used as UART, CODEC or IrDA
+ * GPIO on PSC6_3 is used in post_hotkeys_pressed() to enable extended POST
+ * tests.
+ */
+#define CONFIG_SYS_GPS_PORT_CONFIG 0x81500114
+
+/*
+ * RTC configuration
+ */
+#define CONFIG_RTC_M41T11 1
+#define CONFIG_SYS_I2C_RTC_ADDR 0x68
+#define CONFIG_SYS_M41T11_BASE_YEAR 1900 /* because Linux uses the same base
+ year */
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
+#if defined(CONFIG_CMD_KGDB)
+#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
+#else
+#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
+#endif
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
+
+#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */
+#if defined(CONFIG_CMD_KGDB)
+# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */
+#endif
+
+/* Enable an alternate, more extensive memory test */
+#define CONFIG_SYS_ALT_MEMTEST
+
+#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */
+#define CONFIG_SYS_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */
+
+#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
+
+/*
+ * Enable loopw command.
+ */
+#define CONFIG_LOOPW
+
+/*
+ * Various low-level settings
+ */
+#define CONFIG_SYS_HID0_INIT HID0_ICE | HID0_ICFI
+#define CONFIG_SYS_HID0_FINAL HID0_ICE
+
+#define CONFIG_SYS_BOOTCS_START CONFIG_SYS_FLASH_BASE
+#define CONFIG_SYS_BOOTCS_SIZE CONFIG_SYS_FLASH_SIZE
+#ifdef CONFIG_SYS_PCICLK_EQUALS_IPBCLK_DIV2
+#define CONFIG_SYS_BOOTCS_CFG 0x0008DF30 /* for pci_clk = 66 MHz */
+#else
+#define CONFIG_SYS_BOOTCS_CFG 0x0004DF30 /* for pci_clk = 33 MHz */
+#endif
+#define CONFIG_SYS_CS0_START CONFIG_SYS_FLASH_BASE
+#define CONFIG_SYS_CS0_SIZE CONFIG_SYS_FLASH_SIZE
+
+#define CONFIG_LAST_STAGE_INIT
+
+/*
+ * SRAM - Do not map below 2 GB in address space, because this area is used
+ * for SDRAM autosizing.
+ */
+#define CONFIG_SYS_CS2_START 0xE5000000
+#define CONFIG_SYS_CS2_SIZE 0x100000 /* 1 MByte */
+#define CONFIG_SYS_CS2_CFG 0x0004D930
+
+/*
+ * Grafic controller - Do not map below 2 GB in address space, because this
+ * area is used for SDRAM autosizing.
+ */
+#define SM501_FB_BASE 0xE0000000
+#define CONFIG_SYS_CS1_START (SM501_FB_BASE)
+#define CONFIG_SYS_CS1_SIZE 0x4000000 /* 64 MByte */
+#define CONFIG_SYS_CS1_CFG 0x8F48FF70
+#define SM501_MMIO_BASE CONFIG_SYS_CS1_START + 0x03E00000
+
+#define CONFIG_SYS_CS_BURST 0x00000000
+#define CONFIG_SYS_CS_DEADCYCLE 0x33333311 /* 1 dead cycle for flash and SM501 */
+
+#define CONFIG_SYS_RESET_ADDRESS 0xff000000
+
+/*-----------------------------------------------------------------------
+ * USB stuff
+ *-----------------------------------------------------------------------
+ */
+#define CONFIG_USB_CLOCK 0x0001BBBB
+#define CONFIG_USB_CONFIG 0x00001000
+
+/*-----------------------------------------------------------------------
+ * IDE/ATA stuff Supports IDE harddisk
+ *-----------------------------------------------------------------------
+ */
+
+#undef CONFIG_IDE_8xx_PCCARD /* Use IDE with PC Card Adapter */
+
+#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */
+#undef CONFIG_IDE_LED /* LED for ide not supported */
+
+#define CONFIG_IDE_RESET /* reset for ide supported */
+#define CONFIG_IDE_PREINIT
+
+#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */
+#define CONFIG_SYS_IDE_MAXDEVICE 2 /* max. 2 drives per IDE bus */
+
+#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000
+
+#define CONFIG_SYS_ATA_BASE_ADDR MPC5XXX_ATA
+
+/* Offset for data I/O */
+#define CONFIG_SYS_ATA_DATA_OFFSET (0x0060)
+
+/* Offset for normal register accesses */
+#define CONFIG_SYS_ATA_REG_OFFSET (CONFIG_SYS_ATA_DATA_OFFSET)
+
+/* Offset for alternate registers */
+#define CONFIG_SYS_ATA_ALT_OFFSET (0x005C)
+
+/* Interval between registers */
+#define CONFIG_SYS_ATA_STRIDE 4
+
+#endif /* __CONFIG_H */
Code Review / kvmfornfv.git / blobdiff