--- /dev/null
+/*
+ * (C) Copyright 2004
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ * Sam Song, IEMC. SHU, samsongshu@yahoo.com.cn
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+/*
+ * board/config.h - configuration options, board specific
+ */
+
+/* Yoo. Jonghoon, IPone, yooth@ipone.co.kr
+ * U-BOOT port on RPXlite board
+ */
+
+/*
+ * Sam Song, IEMC. SHU, samsongshu@yahoo.com.cn
+ * U-BOOT port on RPXlite DW version board--RPXlite_DW
+ * June 8 ,2004
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+
+/* #define DEBUG 1 */
+/* #define DEPLOYMENT 1 */
+
+#undef CONFIG_MPC860
+#define CONFIG_MPC823 1 /* This is a MPC823e CPU. */
+#define CONFIG_RPXLITE 1 /* RPXlite DW version board */
+
+#define CONFIG_SYS_TEXT_BASE 0xff000000
+
+#ifdef CONFIG_LCD /* with LCD controller ? */
+#define CONFIG_MPC8XX_LCD
+#define CONFIG_SPLASH_SCREEN /* ... with splashscreen support*/
+#endif
+
+#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */
+#undef CONFIG_8xx_CONS_SMC2
+#undef CONFIG_8xx_CONS_NONE
+#define CONFIG_BAUDRATE 9600 /* console default baudrate = 9600bps */
+
+#ifdef DEBUG
+#define CONFIG_BOOTDELAY -1 /* autoboot disabled */
+#else
+#define CONFIG_BOOTDELAY 6 /* autoboot after 6 seconds */
+
+#ifdef DEPLOYMENT
+#define CONFIG_BOOT_RETRY_TIME -1
+#define CONFIG_AUTOBOOT_KEYED
+#define CONFIG_AUTOBOOT_PROMPT \
+ "autoboot in %d seconds (stop with 'st')...\n", bootdelay
+#define CONFIG_AUTOBOOT_STOP_STR "st"
+#define CONFIG_ZERO_BOOTDELAY_CHECK
+#define CONFIG_RESET_TO_RETRY 1
+#define CONFIG_BOOT_RETRY_MIN 1
+#endif /* DEPLOYMENT */
+#endif /* DEBUG */
+
+/* pre-boot commands */
+#define CONFIG_PREBOOT "setenv stdout serial;setenv stdin serial"
+
+#undef CONFIG_BOOTARGS
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "netdev=eth0\0" \
+ "nfsargs=setenv bootargs console=tty0 console=ttyS0,9600 " \
+ "root=/dev/nfs rw nfsroot=${serverip}:${rootpath}\0" \
+ "ramargs=setenv bootargs console=tty0 root=/dev/ram rw\0" \
+ "addip=setenv bootargs ${bootargs} " \
+ "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
+ ":${hostname}:${netdev}:off panic=1\0" \
+ "flash_nfs=run nfsargs addip;" \
+ "bootm ${kernel_addr}\0" \
+ "flash_self=run ramargs addip;" \
+ "bootm ${kernel_addr} ${ramdisk_addr}\0" \
+ "net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0" \
+ "gatewayip=172.16.115.254\0" \
+ "netmask=255.255.255.0\0" \
+ "kernel_addr=ff040000\0" \
+ "ramdisk_addr=ff200000\0" \
+ "ku=era ${kernel_addr} ff1fffff;cp.b 100000 ${kernel_addr} " \
+ "${filesize};md ${kernel_addr};" \
+ "echo kernel updating finished\0" \
+ "uu=protect off 1:0-4;era 1:0-4;cp.b 100000 ff000000 " \
+ "${filesize};md ff000000;" \
+ "echo u-boot updating finished\0" \
+ "eu=protect off 1:6;era 1:6;reset\0" \
+ "lcd=setenv stdout lcd;setenv stdin lcd\0" \
+ "ser=setenv stdout serial;setenv stdin serial\0" \
+ "verify=no"
+
+#define CONFIG_BOOTCOMMAND "run flash_self"
+
+#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
+#undef CONFIG_SYS_LOADS_BAUD_CHANGE /* don't allow baudrate change */
+#undef CONFIG_WATCHDOG /* watchdog disabled */
+#undef CONFIG_STATUS_LED /* disturbs display. Status LED disabled. */
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_SUBNETMASK
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_BOOTFILESIZE
+
+
+#if 1 /* Enable this stuff could make image enlarge about 25KB. Mask it if you
+ don't want the advanced function */
+
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_ASKENV
+#define CONFIG_CMD_JFFS2
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_REGINFO
+#define CONFIG_CMD_DHCP
+
+#ifdef CONFIG_SPLASH_SCREEN
+#define CONFIG_CMD_BMP
+#endif
+
+
+/* test-only */
+#define CONFIG_SYS_JFFS2_FIRST_BANK 0 /* use for JFFS2 */
+#define CONFIG_SYS_JFFS2_NUM_BANKS 1 /* ! second bank contains U-Boot */
+
+#define CONFIG_NETCONSOLE
+
+#endif /* 1 */
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#define CONFIG_SYS_PROMPT "u-boot>" /* Monitor Command Prompt */
+
+#if defined(CONFIG_CMD_KGDB)
+#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
+#else
+#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
+#endif
+
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
+
+#define CONFIG_SYS_MEMTEST_START 0x0040000 /* memtest works on */
+#define CONFIG_SYS_MEMTEST_END 0x00C0000 /* 4 ... 12 MB in DRAM */
+#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
+
+/*
+ * Low Level Configuration Settings
+ * (address mappings, register initial values, etc.)
+ * You should know what you are doing if you make changes here.
+ */
+/*-----------------------------------------------------------------------
+ * Internal Memory Mapped Register
+ */
+#define CONFIG_SYS_IMMR 0xFA200000
+
+/*-----------------------------------------------------------------------
+ * Definitions for initial stack pointer and data area (in DPRAM)
+ */
+#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR
+#define CONFIG_SYS_INIT_RAM_SIZE 0x2F00 /* Size of used area in DPRAM */
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
+
+/*-----------------------------------------------------------------------
+ * Start addresses for the final memory configuration
+ * (Set up by the startup code)
+ * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
+ */
+#define CONFIG_SYS_SDRAM_BASE 0x00000000
+#define CONFIG_SYS_FLASH_BASE 0xFF000000
+
+#if defined(DEBUG) || defined(CONFIG_CMD_IDE)
+#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
+#else
+#define CONFIG_SYS_MONITOR_LEN (128 << 10) /* Reserve 128 kB for Monitor */
+#endif
+
+#define CONFIG_SYS_MONITOR_BASE 0xFF000000
+#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+
+/*-----------------------------------------------------------------------
+ * FLASH organization
+ */
+#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
+#define CONFIG_SYS_MAX_FLASH_SECT 71 /* max number of sectors on one chip */
+#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
+
+#ifdef CONFIG_ENV_IS_IN_NVRAM
+#define CONFIG_ENV_ADDR 0xFA000100
+#define CONFIG_ENV_SIZE 0x1000
+#else
+#define CONFIG_ENV_IS_IN_FLASH
+#define CONFIG_ENV_OFFSET 0x30000 /* Offset of Environment Sector */
+#define CONFIG_ENV_SIZE 0x8000 /* Total Size of Environment Sector */
+#endif /* CONFIG_ENV_IS_IN_NVRAM */
+
+#define CONFIG_SYS_RESET_ADDRESS ((ulong)((((immap_t *)CONFIG_SYS_IMMR)->im_clkrst.res)))
+
+/*-----------------------------------------------------------------------
+ * Cache Configuration
+ */
+#define CONFIG_SYS_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */
+#if defined(CONFIG_CMD_KGDB)
+#define CONFIG_SYS_CACHELINE_SHIFT 4 /* log base 2 of the above value */
+#endif
+
+/*-----------------------------------------------------------------------
+ * SYPCR - System Protection Control 32-bit 12-35
+ * SYPCR can only be written once after reset!
+ *-----------------------------------------------------------------------
+ * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
+ */
+#if defined(CONFIG_WATCHDOG)
+#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
+ SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP)
+#else
+#define CONFIG_SYS_SYPCR (SYPCR_SWTC | 0x00000600 | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
+#endif /* We can get SYPCR: 0xFFFF0689. */
+
+/*-----------------------------------------------------------------------
+ * SIUMCR - SIU Module Configuration 32-bit 12-30
+ *-----------------------------------------------------------------------
+ * PCMCIA config., multi-function pin tri-state
+ */
+#define CONFIG_SYS_SIUMCR (SIUMCR_MLRC10) /* SIUMCR:0x00000800 */
+
+/*---------------------------------------------------------------------
+ * TBSCR - Time Base Status and Control 16-bit 12-16
+ *---------------------------------------------------------------------
+ * Clear Reference Interrupt Status, Timebase freezing enabled
+ */
+#define CONFIG_SYS_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF | TBSCR_TBE)
+/* TBSCR: 0x00C3 [SAM] */
+
+/*-----------------------------------------------------------------------
+ * RTCSC - Real-Time Clock Status and Control Register 16-bit 12-18
+ *-----------------------------------------------------------------------
+ * [RTC enabled but not stopped on FRZ]
+ */
+#define CONFIG_SYS_RTCSC (RTCSC_SEC | RTCSC_ALR | RTCSC_RTE) /* RTCSC:0x00C1 */
+
+/*-----------------------------------------------------------------------
+ * PISCR - Periodic Interrupt Status and Control 16-bit 12-23
+ *-----------------------------------------------------------------------
+ * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
+ * [Periodic timer enabled,Periodic timer interrupt disable. ]
+ */
+#define CONFIG_SYS_PISCR (PISCR_PS | PISCR_PITF | PISCR_PTE) /* PISCR:0x0083 */
+
+/*-----------------------------------------------------------------------
+ * PLPRCR - PLL, Low-Power, and Reset Control Register 32-bit 5-7
+ *-----------------------------------------------------------------------
+ * Reset PLL lock status sticky bit, timer expired status bit and timer
+ * interrupt status bit
+ */
+/* up to 64 MHz we use a 1:2 clock */
+#if defined(RPXlite_64MHz)
+#define CONFIG_SYS_PLPRCR ( (7 << PLPRCR_MF_SHIFT) | PLPRCR_TEXPS ) /*PLPRCR: 0x00700000. */
+#else
+#define CONFIG_SYS_PLPRCR ( (5 << PLPRCR_MF_SHIFT) | PLPRCR_TEXPS )
+#endif
+
+/*-----------------------------------------------------------------------
+ * SCCR - System Clock and reset Control Register 5-3
+ *-----------------------------------------------------------------------
+ * Set clock output, timebase and RTC source and divider,
+ * power management and some other internal clocks
+ */
+#define SCCR_MASK SCCR_EBDF00
+/* Up to 48MHz system clock, we use 1:1 SYSTEM/BUS ratio */
+#if defined(RPXlite_64MHz)
+#define CONFIG_SYS_SCCR ( SCCR_TBS | SCCR_EBDF01 ) /* %%%SCCR:0x02020000 */
+#else
+#define CONFIG_SYS_SCCR ( SCCR_TBS | SCCR_EBDF00 ) /* %%%SCCR:0x02000000 */
+#endif
+
+/*-----------------------------------------------------------------------
+ * PCMCIA stuff
+ *-----------------------------------------------------------------------
+ */
+#define CONFIG_SYS_PCMCIA_MEM_ADDR (0xE0000000)
+#define CONFIG_SYS_PCMCIA_MEM_SIZE ( 64 << 20 )
+#define CONFIG_SYS_PCMCIA_DMA_ADDR (0xE4000000)
+#define CONFIG_SYS_PCMCIA_DMA_SIZE ( 64 << 20 )
+#define CONFIG_SYS_PCMCIA_ATTRB_ADDR (0xE8000000)
+#define CONFIG_SYS_PCMCIA_ATTRB_SIZE ( 64 << 20 )
+#define CONFIG_SYS_PCMCIA_IO_ADDR (0xEC000000)
+#define CONFIG_SYS_PCMCIA_IO_SIZE ( 64 << 20 )
+
+/*-----------------------------------------------------------------------
+ * IDE/ATA stuff (Supports IDE harddisk on PCMCIA Adapter)
+ *-----------------------------------------------------------------------
+ */
+#define CONFIG_IDE_PREINIT 1 /* Use preinit IDE hook */
+#define CONFIG_IDE_8xx_PCCARD 1 /* Use IDE with PC Card Adapter */
+
+#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */
+#undef CONFIG_IDE_LED /* LED for ide not supported */
+#undef CONFIG_IDE_RESET /* reset for ide not supported */
+
+#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */
+#define CONFIG_SYS_IDE_MAXDEVICE 1 /* max. 1 drive per IDE bus */
+
+#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000
+#define CONFIG_SYS_ATA_BASE_ADDR CONFIG_SYS_PCMCIA_MEM_ADDR
+
+/* Offset for data I/O */
+#define CONFIG_SYS_ATA_DATA_OFFSET (CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
+
+/* Offset for normal register accesses */
+#define CONFIG_SYS_ATA_REG_OFFSET (2 * CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
+
+/* Offset for alternate registers */
+#define CONFIG_SYS_ATA_ALT_OFFSET 0x0100
+
+#define CONFIG_SYS_DER 0
+
+/*
+ * Init Memory Controller:
+ *
+ * BR0 and OR0 (FLASH)
+ */
+#define FLASH_BASE_PRELIM 0xFC000000 /* FLASH base */
+#define CONFIG_SYS_PRELIM_OR_AM 0xFC000000 /* OR addr mask */
+
+/* FLASH timing: ACS = 0, TRLX = 0, CSNT = 0, SCY = 8, ETHR = 0, BIH = 1 */
+#define CONFIG_SYS_OR_TIMING_FLASH (OR_SCY_8_CLK | OR_BI)
+#define CONFIG_SYS_OR0_PRELIM (CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_FLASH)
+#define CONFIG_SYS_BR0_PRELIM ((FLASH_BASE_PRELIM & BR_BA_MSK) | BR_V)
+
+/*
+ * BR1 and OR1 (SDRAM)
+ *
+ */
+#define SDRAM_BASE_PRELIM 0x00000000 /* SDRAM base */
+#define SDRAM_MAX_SIZE 0x08000000 /* max 128 MB in system */
+
+/* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care) */
+#define CONFIG_SYS_OR_TIMING_SDRAM 0x00000E00
+#define CONFIG_SYS_OR_AM_SDRAM (-(SDRAM_MAX_SIZE & OR_AM_MSK))
+#define CONFIG_SYS_OR1_PRELIM ( CONFIG_SYS_OR_AM_SDRAM | CONFIG_SYS_OR_TIMING_SDRAM )
+#define CONFIG_SYS_BR1_PRELIM ((SDRAM_BASE_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
+
+/* RPXlite mem setting */
+#define CONFIG_SYS_BR3_PRELIM 0xFA400001 /* BCSR */
+#define CONFIG_SYS_OR3_PRELIM 0xFF7F8900
+#define CONFIG_SYS_BR4_PRELIM 0xFA000401 /* NVRAM&SRAM */
+#define CONFIG_SYS_OR4_PRELIM 0xFFFE0040
+
+/*
+ * Memory Periodic Timer Prescaler
+ */
+/* periodic timer for refresh */
+#if defined(RPXlite_64MHz)
+#define CONFIG_SYS_MAMR_PTA 32
+#else
+#define CONFIG_SYS_MAMR_PTA 20
+#endif
+
+/*
+ * Refresh clock Prescalar
+ */
+#define CONFIG_SYS_MPTPR MPTPR_PTP_DIV2
+
+/*
+ * MAMR settings for SDRAM
+ */
+
+/* 9 column SDRAM */
+#define CONFIG_SYS_MAMR_9COL ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \
+ MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10)
+/* CONFIG_SYS_MAMR_9COL:0x20904000 @ 64MHz */
+
+/*%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%% */
+/* Configuration variable added by yooth. */
+/*%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%% */
+/*
+ * BCSRx
+ *
+ * Board Status and Control Registers
+ *
+ */
+#define BCSR0 0xFA400000
+#define BCSR1 0xFA400001
+#define BCSR2 0xFA400002
+#define BCSR3 0xFA400003
+
+#define BCSR0_ENMONXCVR 0x01 /* Monitor XVCR Control */
+#define BCSR0_ENNVRAM 0x02 /* CS4# Control */
+#define BCSR0_LED5 0x04 /* LED5 control 0='on' 1='off' */
+#define BCSR0_LED4 0x08 /* LED4 control 0='on' 1='off' */
+#define BCSR0_FULLDPLX 0x10 /* Ethernet XCVR Control */
+#define BCSR0_COLTEST 0x20
+#define BCSR0_ETHLPBK 0x40
+#define BCSR0_ETHEN 0x80
+
+#define BCSR1_PCVCTL7 0x01 /* PC Slot B Control */
+#define BCSR1_PCVCTL6 0x02
+#define BCSR1_PCVCTL5 0x04
+#define BCSR1_PCVCTL4 0x08
+#define BCSR1_IPB5SEL 0x10
+
+#define BCSR1_SMC1CTS 0x40 /* Added by SAM. */
+#define BCSR1_SMC1TRS 0x80 /* Added by SAM. */
+
+#define BCSR2_ENRTCIRQ 0x01 /* Added by SAM. */
+#define BCSR2_ENBRG1 0x04 /* Added by SAM. */
+
+#define BCSR2_ENPA5HDR 0x08 /* USB Control */
+#define BCSR2_ENUSBCLK 0x10
+#define BCSR2_USBPWREN 0x20
+#define BCSR2_USBSPD 0x40
+#define BCSR2_USBSUSP 0x80
+
+#define BCSR3_BWKAPWR 0x01 /* Changed by SAM. Backup battery situation */
+#define BCSR3_IRQRTC 0x02 /* Changed by SAM. NVRAM Battery */
+#define BCSR3_RDY_BSY 0x04 /* Changed by SAM. Flash Operation */
+#define BCSR3_MPLX_LIN 0x08 /* Changed by SAM. Linear or Multiplexed address Mode */
+
+#define BCSR3_D27 0x10 /* Dip Switch settings */
+#define BCSR3_D26 0x20
+#define BCSR3_D25 0x40
+#define BCSR3_D24 0x80
+
+/*
+ * Environment setting
+ */
+#define CONFIG_ETHADDR 00:10:EC:00:37:5B
+#define CONFIG_IPADDR 172.16.115.7
+#define CONFIG_SERVERIP 172.16.115.6
+#define CONFIG_ROOTPATH "/workspace/myfilesystem/target/"
+#define CONFIG_BOOTFILE "uImage.rpxusb"
+#define CONFIG_HOSTNAME LITE_H1_DW
+
+#endif /* __CONFIG_H */
Code Review / kvmfornfv.git / blobdiff