--- /dev/null
+/*
+ * (C) Copyright 2001-2004
+ * Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ */
+
+#define CONFIG_405GP 1 /* This is a PPC405 CPU */
+#define CONFIG_PMC405 1 /* ...on a PMC405 board */
+
+#define CONFIG_SYS_TEXT_BASE 0xFFF80000
+
+#define CONFIG_BOARD_EARLY_INIT_F 1 /* call board_early_init_f() */
+#define CONFIG_MISC_INIT_R 1 /* call misc_init_r() */
+
+#define CONFIG_SYS_CLK_FREQ 33330000 /* external frequency to pll */
+
+#define CONFIG_BAUDRATE 9600
+#define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */
+
+/* Only interrupt boot if space is pressed. */
+#define CONFIG_AUTOBOOT_KEYED 1
+#define CONFIG_AUTOBOOT_PROMPT \
+ "Press SPACE to abort autoboot in %d seconds\n", bootdelay
+#undef CONFIG_AUTOBOOT_DELAY_STR
+#define CONFIG_AUTOBOOT_STOP_STR " "
+
+#undef CONFIG_BOOTARGS
+#undef CONFIG_BOOTCOMMAND
+
+#define CONFIG_PREBOOT /* enable preboot variable */
+
+#define CFG_BOOTM_LEN 0x1000000 /* support booting of huge images */
+
+#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
+#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
+
+#undef CONFIG_HAS_ETH1
+
+#define CONFIG_PPC4xx_EMAC
+#define CONFIG_MII 1 /* MII PHY management */
+#define CONFIG_PHY_ADDR 0 /* PHY address */
+#define CONFIG_LXT971_NO_SLEEP 1 /* disable sleep mode in LXT971 */
+#define CONFIG_RESET_PHY_R 1 /* use reset_phy() */
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_BSP
+#define CONFIG_CMD_PCI
+#define CONFIG_CMD_IRQ
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_DATE
+#define CONFIG_CMD_JFFS2
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_UNIVERSE
+#define CONFIG_CMD_EEPROM
+
+#define CONFIG_MAC_PARTITION
+#define CONFIG_DOS_PARTITION
+
+#undef CONFIG_WATCHDOG /* watchdog disabled */
+
+#define CONFIG_RTC_MC146818 /* DS1685 is MC146818 compatible */
+#define CONFIG_SYS_RTC_REG_BASE_ADDR 0xF0000500 /* RTC Base Address */
+
+#define CONFIG_SDRAM_BANK0 1 /* init onboard SDRAM bank 0 */
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+
+#undef CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */
+
+#if defined(CONFIG_CMD_KGDB)
+#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
+#else
+#define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */
+#endif
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Sz */
+
+#define CONFIG_SYS_DEVICE_NULLDEV 1 /* include nulldev device */
+
+#define CONFIG_SYS_CONSOLE_INFO_QUIET 1 /* don't print console info */
+
+#define CONFIG_AUTO_COMPLETE 1 /* add autocompletion support */
+
+#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */
+#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
+
+#define CONFIG_CONS_INDEX 1 /* Use UART0 */
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE 1
+#define CONFIG_SYS_NS16550_CLK get_serial_clock()
+
+#undef CONFIG_SYS_EXT_SERIAL_CLOCK /* no external serial clock */
+#define CONFIG_SYS_BASE_BAUD 806400
+
+/* The following table includes the supported baudrates */
+#define CONFIG_SYS_BAUDRATE_TABLE \
+ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
+
+#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
+#define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_into (bd_t) */
+
+#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
+#define CONFIG_LOOPW 1 /* enable loopw command */
+
+#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
+
+#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
+
+#define CONFIG_SYS_RX_ETH_BUFFER 16
+
+/*
+ * PCI stuff
+ */
+#define PCI_HOST_ADAPTER 0 /* configure as pci adapter */
+#define PCI_HOST_FORCE 1 /* configure as pci host */
+#define PCI_HOST_AUTO 2 /* detected via arbiter enable */
+
+#define CONFIG_PCI /* include pci support */
+#define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */
+#define CONFIG_PCI_HOST PCI_HOST_AUTO /* select pci host function */
+#define CONFIG_PCI_PNP /* do pci plug-and-play */
+ /* resource configuration */
+
+#define CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */
+
+#define CONFIG_PCI_CONFIG_HOST_BRIDGE 1 /* don't skip host bridge config */
+
+#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x12FE /* PCI Vendor ID: esd gmbh */
+#define CONFIG_SYS_PCI_SUBSYS_DEVICEID_NONMONARCH 0x0408 /* PCI Device ID */
+#define CONFIG_SYS_PCI_SUBSYS_DEVICEID_MONARCH 0x0409 /* PCI Device ID */
+#define CONFIG_SYS_PCI_SUBSYS_DEVICEID pmc405_pci_subsys_deviceid()
+
+#define CONFIG_SYS_PCI_CLASSCODE 0x0b20 /* Processor/PPC */
+
+#define CONFIG_SYS_PCI_PTM1LA (bd->bi_memstart) /* point to sdram */
+#define CONFIG_SYS_PCI_PTM1MS (~(bd->bi_memsize - 1) | 1) /* memsize, enable */
+#define CONFIG_SYS_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */
+#define CONFIG_SYS_PCI_PTM2LA 0xef000000 /* point to internal regs */
+#define CONFIG_SYS_PCI_PTM2MS 0xff000001 /* 16MB, enable */
+#define CONFIG_SYS_PCI_PTM2PCI 0x00000000 /* Host: use this pci address */
+
+#define CONFIG_PCI_4xx_PTM_OVERWRITE 1 /* overwrite PTMx settings by env */
+
+/*
+ * Start addresses for the final memory configuration
+ * (Set up by the startup code)
+ * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
+ */
+#define CONFIG_SYS_SDRAM_BASE 0x00000000
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
+#define CONFIG_SYS_MONITOR_LEN (~(CONFIG_SYS_TEXT_BASE) + 1)
+#define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* 128 kB for malloc() */
+
+#define CONFIG_PRAM 0 /* use pram variable to overwrite */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+
+/*
+ * FLASH organization
+ */
+#define CONFIG_SYS_FLASH_BASE 0xFE000000
+#define CONFIG_SYS_FLASH_INCREMENT 0x01000000
+
+#define CONFIG_SYS_FLASH_CFI 1 /* Flash is CFI conformant */
+#define CONFIG_FLASH_CFI_DRIVER 1 /* Use the common driver */
+#define CONFIG_SYS_FLASH_PROTECTION 1 /* don't use hardware protection */
+#define CONFIG_SYS_FLASH_AUTOPROTECT_LIST {{0xfff80000, 0x80000}}
+#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (faster) */
+#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max num of flash banks */
+#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE, \
+ CONFIG_SYS_FLASH_BASE + CONFIG_SYS_FLASH_INCREMENT}
+#define CONFIG_SYS_MAX_FLASH_SECT 128 /* max num of sects on one chip */
+#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on fli */
+
+/*
+ * Environment Variable setup
+ */
+#define CONFIG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */
+
+/* environment starts at the beginning of the EEPROM */
+#define CONFIG_ENV_OFFSET 0x000
+#define CONFIG_ENV_SIZE 0x800 /* 2048 bytes may be used for env vars */
+
+#define CONFIG_SYS_NVRAM_BASE_ADDR 0xF0000500 /* NVRAM base address */
+#define CONFIG_SYS_NVRAM_SIZE 242 /* NVRAM size */
+
+/*
+ * I2C EEPROM (CAT24WC16) for environment
+ */
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_PPC4XX
+#define CONFIG_SYS_I2C_PPC4XX_CH0
+#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 100000
+#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F
+
+#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* EEPROM CAT24W16 */
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */
+/* mask of address bits that overflow into the "EEPROM chip address" */
+#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW 0x07
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4 /* The Catalyst CAT24W16 has */
+ /* 16 byte page write mode using*/
+ /* last 4 bits of the address */
+
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */
+
+/*
+ * External Bus Controller (EBC) Setup
+ */
+#define FLASH0_BA 0xFF000000 /* FLASH 0 Base Address */
+#define FLASH1_BA 0xFE000000 /* FLASH 1 Base Address */
+#define CAN_BA 0xF0000000 /* CAN Base Addres */
+#define RTC_BA 0xF0000500 /* RTC Base Address */
+#define NVRAM_BA 0xF0200000 /* NVRAM Base Address */
+
+/* Memory Bank 0 (Flash Bank 0) initialization */
+#define CONFIG_SYS_EBC_PB0AP 0x92015480
+/* BAS=0xFF0,BS=16MB,BU=R/W,BW=16bit */
+#define CONFIG_SYS_EBC_PB0CR (FLASH0_BA | 0x9A000)
+
+/* Memory Bank 1 (Flash Bank 1) initialization */
+#define CONFIG_SYS_EBC_PB1AP 0x92015480
+/* BAS=0xFE0,BS=16MB,BU=R/W,BW=16bit*/
+#define CONFIG_SYS_EBC_PB1CR (FLASH1_BA | 0x9A000)
+
+/* Memory Bank 2 (CAN0, 1, RTC) initialization */
+/* TWT=5,TH=2,CSN=0,OEN=0,WBN=0,WBF=0 */
+#define CONFIG_SYS_EBC_PB2AP 0x03000440
+/* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit */
+#define CONFIG_SYS_EBC_PB2CR (CAN_BA | 0x18000)
+
+/* Memory Bank 3 -> unused */
+
+/* Memory Bank 4 (NVRAM) initialization */
+/* TWT=5,TH=2,CSN=0,OEN=0,WBN=0,WBF=0 */
+#define CONFIG_SYS_EBC_PB4AP 0x03000440
+/* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit */
+#define CONFIG_SYS_EBC_PB4CR (NVRAM_BA | 0x18000)
+
+/*
+ * FPGA stuff
+ */
+/* FPGA program pin configuration */
+#define CONFIG_SYS_FPGA_PRG 0x04000000 /* JTAG TMS pin (output) */
+#define CONFIG_SYS_FPGA_CLK 0x02000000 /* JTAG TCK pin (output) */
+#define CONFIG_SYS_FPGA_DATA 0x01000000 /* JTAG TDO pin (output) */
+#define CONFIG_SYS_FPGA_INIT 0x00010000 /* unused (ppc input) */
+#define CONFIG_SYS_FPGA_DONE 0x00008000 /* JTAG TDI pin (input) */
+
+/* pass Ethernet MAC to VxWorks */
+#define CONFIG_SYS_VXWORKS_MAC_PTR 0x00000000
+
+/*
+ * GPIOs
+ */
+#define CONFIG_SYS_VPEN (0x80000000 >> 3) /* GPIO3 */
+#define CONFIG_SYS_NONMONARCH (0x80000000 >> 14) /* GPIO14 */
+#define CONFIG_SYS_XEREADY (0x80000000 >> 15) /* GPIO15 */
+#define CONFIG_SYS_INTA_FAKE (0x80000000 >> 19) /* GPIO19 */
+#define CONFIG_SYS_SELF_RST (0x80000000 >> 21) /* GPIO21 */
+#define CONFIG_SYS_REV1_2 (0x80000000 >> 23) /* GPIO23 */
+
+/*
+ * Definitions for initial stack pointer and data area (in data cache)
+ */
+
+/* use on chip memory (OCM) for temperary stack until sdram is tested */
+#define CONFIG_SYS_TEMP_STACK_OCM 1
+
+/* On Chip Memory location */
+#define CONFIG_SYS_OCM_DATA_ADDR 0xF8000000
+#define CONFIG_SYS_OCM_DATA_SIZE 0x1000
+
+/* inside of SDRAM */
+#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_DATA_ADDR
+
+/* End of used area in RAM */
+#define CONFIG_SYS_INIT_RAM_SIZE CONFIG_SYS_OCM_DATA_SIZE
+
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \
+ GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
+
+#define CONFIG_OF_LIBFDT
+#define CONFIG_OF_BOARD_SETUP
+
+#endif /* __CONFIG_H */
Code Review / kvmfornfv.git / blobdiff