--- /dev/null
+/*
+ * (C) Copyright 2001-2005
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+/*
+ * board/config.h - configuration options, board specific
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#undef CONFIG_SYS_RAMBOOT
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+
+#define CONFIG_PM828 1 /* ...on a PM828 module */
+#define CONFIG_CPM2 1 /* Has a CPM2 */
+
+#ifndef CONFIG_SYS_TEXT_BASE
+#define CONFIG_SYS_TEXT_BASE 0x40000000 /* Standard: boot 64-bit flash */
+#endif
+
+#undef CONFIG_DB_CR826_J30x_ON /* J30x jumpers on D.B. carrier */
+
+#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
+
+#define CONFIG_PREBOOT "echo;echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;echo"
+
+#undef CONFIG_BOOTARGS
+#define CONFIG_BOOTCOMMAND \
+ "bootp;" \
+ "setenv bootargs root=/dev/nfs rw nfsroot=${serverip}:${rootpath} " \
+ "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off;" \
+ "bootm"
+
+/* enable I2C and select the hardware/software driver */
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_SOFT /* I2C bit-banged */
+#define CONFIG_SYS_I2C_SOFT_SPEED 50000
+#define CONFIG_SYS_I2C_SOFT_SLAVE 0xFE
+/*
+ * Software (bit-bang) I2C driver configuration
+ */
+#define I2C_PORT 3 /* Port A=0, B=1, C=2, D=3 */
+#define I2C_ACTIVE (iop->pdir |= 0x00010000)
+#define I2C_TRISTATE (iop->pdir &= ~0x00010000)
+#define I2C_READ ((iop->pdat & 0x00010000) != 0)
+#define I2C_SDA(bit) if(bit) iop->pdat |= 0x00010000; \
+ else iop->pdat &= ~0x00010000
+#define I2C_SCL(bit) if(bit) iop->pdat |= 0x00020000; \
+ else iop->pdat &= ~0x00020000
+#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */
+
+
+#define CONFIG_RTC_PCF8563
+#define CONFIG_SYS_I2C_RTC_ADDR 0x51
+
+/*
+ * select serial console configuration
+ *
+ * if either CONFIG_CONS_ON_SMC or CONFIG_CONS_ON_SCC is selected, then
+ * CONFIG_CONS_INDEX must be set to the channel number (1-2 for SMC, 1-4
+ * for SCC).
+ *
+ * if CONFIG_CONS_NONE is defined, then the serial console routines must
+ * defined elsewhere (for example, on the cogent platform, there are serial
+ * ports on the motherboard which are used for the serial console - see
+ * cogent/cma101/serial.[ch]).
+ */
+#define CONFIG_CONS_ON_SMC /* define if console on SMC */
+#undef CONFIG_CONS_ON_SCC /* define if console on SCC */
+#undef CONFIG_CONS_NONE /* define if console on something else*/
+#define CONFIG_CONS_INDEX 2 /* which serial channel for console */
+
+/*
+ * select ethernet configuration
+ *
+ * if CONFIG_ETHER_ON_SCC is selected, then
+ * - CONFIG_ETHER_INDEX must be set to the channel number (1-4)
+ *
+ * if CONFIG_ETHER_ON_FCC is selected, then
+ * - one or more CONFIG_ETHER_ON_FCCx (x=1,2,3) must also be selected
+ *
+ * if CONFIG_ETHER_NONE is defined, then either the ethernet routines must be
+ * defined elsewhere (as for the console), or CONFIG_CMD_NET must be unset.
+ */
+#undef CONFIG_ETHER_NONE /* define if ether on something else */
+
+#undef CONFIG_ETHER_ON_SCC /* define if ether on SCC */
+#define CONFIG_ETHER_INDEX 1 /* which SCC channel for ethernet */
+
+#define CONFIG_ETHER_ON_FCC /* define if ether on FCC */
+/*
+ * - Rx-CLK is CLK11
+ * - Tx-CLK is CLK10
+ */
+#define CONFIG_ETHER_ON_FCC1
+# define CONFIG_SYS_CMXFCR_MASK1 (CMXFCR_FC1|CMXFCR_RF1CS_MSK|CMXFCR_TF1CS_MSK)
+#ifndef CONFIG_DB_CR826_J30x_ON
+# define CONFIG_SYS_CMXFCR_VALUE1 (CMXFCR_RF1CS_CLK11|CMXFCR_TF1CS_CLK10)
+#else
+# define CONFIG_SYS_CMXFCR_VALUE1 (CMXFCR_RF1CS_CLK11|CMXFCR_TF1CS_CLK12)
+#endif
+/*
+ * - Rx-CLK is CLK15
+ * - Tx-CLK is CLK14
+ */
+#define CONFIG_ETHER_ON_FCC2
+# define CONFIG_SYS_CMXFCR_MASK2 (CMXFCR_FC2|CMXFCR_RF2CS_MSK|CMXFCR_TF2CS_MSK)
+# define CONFIG_SYS_CMXFCR_VALUE2 (CMXFCR_RF2CS_CLK13|CMXFCR_TF2CS_CLK14)
+/*
+ * - RAM for BD/Buffers is on the 60x Bus (see 28-13)
+ * - Enable Full Duplex in FSMR
+ */
+# define CONFIG_SYS_CPMFCR_RAMTYPE 0
+# define CONFIG_SYS_FCC_PSMR (FCC_PSMR_FDE|FCC_PSMR_LPB)
+
+/* system clock rate (CLKIN) - equal to the 60x and local bus speed */
+#define CONFIG_8260_CLKIN 100000000 /* in Hz */
+
+#if defined(CONFIG_CONS_NONE) || defined(CONFIG_CONS_USE_EXTC)
+#define CONFIG_BAUDRATE 230400
+#else
+#define CONFIG_BAUDRATE 9600
+#endif
+
+#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
+#undef CONFIG_SYS_LOADS_BAUD_CHANGE /* don't allow baudrate change */
+
+#undef CONFIG_WATCHDOG /* watchdog disabled */
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_SUBNETMASK
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_BOOTFILESIZE
+
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_BEDBUG
+#define CONFIG_CMD_DATE
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_EEPROM
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_NFS
+#define CONFIG_CMD_SNTP
+
+#ifdef CONFIG_PCI
+#define CONFIG_PCI_INDIRECT_BRIDGE
+#define CONFIG_CMD_PCI
+#endif
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#if defined(CONFIG_CMD_KGDB)
+#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
+#else
+#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
+#endif
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
+
+#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */
+#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
+
+#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
+
+#define CONFIG_SYS_RESET_ADDRESS 0xFDFFFFFC /* "bad" address */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+
+/*-----------------------------------------------------------------------
+ * Flash and Boot ROM mapping
+ */
+
+#define CONFIG_SYS_BOOTROM_BASE 0xFF800000
+#define CONFIG_SYS_BOOTROM_SIZE 0x00080000
+#define CONFIG_SYS_FLASH0_BASE 0x40000000
+#define CONFIG_SYS_FLASH0_SIZE 0x02000000
+#define CONFIG_SYS_DOC_BASE 0xFF800000
+#define CONFIG_SYS_DOC_SIZE 0x00100000
+
+
+/* Flash bank size (for preliminary settings)
+ */
+#define CONFIG_SYS_FLASH_SIZE CONFIG_SYS_FLASH0_SIZE
+
+/*-----------------------------------------------------------------------
+ * FLASH organization
+ */
+#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of memory banks */
+#define CONFIG_SYS_MAX_FLASH_SECT 135 /* max num of sects on one chip */
+
+#define CONFIG_SYS_FLASH_ERASE_TOUT 240000 /* Flash Erase Timeout (in ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (in ms) */
+
+#if 0
+/* Start port with environment in flash; switch to EEPROM later */
+#define CONFIG_ENV_IS_IN_FLASH 1
+#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE+0x40000)
+#define CONFIG_ENV_SIZE 0x40000
+#define CONFIG_ENV_SECT_SIZE 0x40000
+#else
+/* Final version: environment in EEPROM */
+#define CONFIG_ENV_IS_IN_EEPROM 1
+#define CONFIG_SYS_I2C_EEPROM_ADDR 0x58
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */
+#define CONFIG_ENV_OFFSET 512
+#define CONFIG_ENV_SIZE (2048 - 512)
+#endif
+
+/*-----------------------------------------------------------------------
+ * Hard Reset Configuration Words
+ *
+ * if you change bits in the HRCW, you must also change the CONFIG_SYS_*
+ * defines for the various registers affected by the HRCW e.g. changing
+ * HRCW_DPPCxx requires you to also change CONFIG_SYS_SIUMCR.
+ */
+#if defined(CONFIG_BOOT_ROM)
+#define CONFIG_SYS_HRCW_MASTER (HRCW_BPS01 | HRCW_CIP | HRCW_ISB100 | HRCW_BMS)
+#else
+#define CONFIG_SYS_HRCW_MASTER (HRCW_CIP | HRCW_ISB100 | HRCW_BMS)
+#endif
+
+/* no slaves so just fill with zeros */
+#define CONFIG_SYS_HRCW_SLAVE1 0
+#define CONFIG_SYS_HRCW_SLAVE2 0
+#define CONFIG_SYS_HRCW_SLAVE3 0
+#define CONFIG_SYS_HRCW_SLAVE4 0
+#define CONFIG_SYS_HRCW_SLAVE5 0
+#define CONFIG_SYS_HRCW_SLAVE6 0
+#define CONFIG_SYS_HRCW_SLAVE7 0
+
+/*-----------------------------------------------------------------------
+ * Internal Memory Mapped Register
+ */
+#define CONFIG_SYS_IMMR 0xF0000000
+
+/*-----------------------------------------------------------------------
+ * Definitions for initial stack pointer and data area (in DPRAM)
+ */
+#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR
+#define CONFIG_SYS_INIT_RAM_SIZE 0x4000 /* Size of used area in DPRAM */
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
+
+/*-----------------------------------------------------------------------
+ * Start addresses for the final memory configuration
+ * (Set up by the startup code)
+ * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
+ *
+ * 60x SDRAM is mapped at CONFIG_SYS_SDRAM_BASE, local SDRAM
+ * is mapped at SDRAM_BASE2_PRELIM.
+ */
+#define CONFIG_SYS_SDRAM_BASE 0x00000000
+#define CONFIG_SYS_FLASH_BASE CONFIG_SYS_FLASH0_BASE
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
+#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
+#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc()*/
+
+#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
+# define CONFIG_SYS_RAMBOOT
+#endif
+
+#ifdef CONFIG_PCI
+#define CONFIG_PCI_PNP
+#define CONFIG_EEPRO100
+#define CONFIG_SYS_RX_ETH_BUFFER 8 /* use 8 rx buffer on eepro100 */
+#endif
+
+/*-----------------------------------------------------------------------
+ * Cache Configuration
+ */
+#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC8260 CPU */
+#if defined(CONFIG_CMD_KGDB)
+# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */
+#endif
+
+/*-----------------------------------------------------------------------
+ * HIDx - Hardware Implementation-dependent Registers 2-11
+ *-----------------------------------------------------------------------
+ * HID0 also contains cache control - initially enable both caches and
+ * invalidate contents, then the final state leaves only the instruction
+ * cache enabled. Note that Power-On and Hard reset invalidate the caches,
+ * but Soft reset does not.
+ *
+ * HID1 has only read-only information - nothing to set.
+ */
+#define CONFIG_SYS_HID0_INIT (HID0_ICE|HID0_DCE|HID0_ICFI|HID0_DCI|\
+ HID0_IFEM|HID0_ABE)
+#define CONFIG_SYS_HID0_FINAL (HID0_ICE|HID0_IFEM|HID0_ABE)
+#define CONFIG_SYS_HID2 0
+
+/*-----------------------------------------------------------------------
+ * RMR - Reset Mode Register 5-5
+ *-----------------------------------------------------------------------
+ * turn on Checkstop Reset Enable
+ */
+#define CONFIG_SYS_RMR RMR_CSRE
+
+/*-----------------------------------------------------------------------
+ * BCR - Bus Configuration 4-25
+ *-----------------------------------------------------------------------
+ */
+
+#define BCR_APD01 0x10000000
+#define CONFIG_SYS_BCR (BCR_APD01|BCR_ETM|BCR_LETM) /* 8260 mode */
+
+/*-----------------------------------------------------------------------
+ * SIUMCR - SIU Module Configuration 4-31
+ *-----------------------------------------------------------------------
+ */
+#if 0
+#define CONFIG_SYS_SIUMCR (SIUMCR_DPPC00|SIUMCR_APPC10|SIUMCR_CS10PC01)
+#else
+#define CONFIG_SYS_SIUMCR (SIUMCR_DPPC10|SIUMCR_APPC10)
+#endif
+
+
+/*-----------------------------------------------------------------------
+ * SYPCR - System Protection Control 4-35
+ * SYPCR can only be written once after reset!
+ *-----------------------------------------------------------------------
+ * Watchdog & Bus Monitor Timer max, 60x Bus Monitor enable
+ */
+#if defined(CONFIG_WATCHDOG)
+#define CONFIG_SYS_SYPCR (SYPCR_SWTC|SYPCR_BMT|SYPCR_PBME|SYPCR_LBME|\
+ SYPCR_SWRI|SYPCR_SWP|SYPCR_SWE)
+#else
+#define CONFIG_SYS_SYPCR (SYPCR_SWTC|SYPCR_BMT|SYPCR_PBME|SYPCR_LBME|\
+ SYPCR_SWRI|SYPCR_SWP)
+#endif /* CONFIG_WATCHDOG */
+
+/*-----------------------------------------------------------------------
+ * TMCNTSC - Time Counter Status and Control 4-40
+ *-----------------------------------------------------------------------
+ * Clear once per Second and Alarm Interrupt Status, Set 32KHz timersclk,
+ * and enable Time Counter
+ */
+#define CONFIG_SYS_TMCNTSC (TMCNTSC_SEC|TMCNTSC_ALR|TMCNTSC_TCF|TMCNTSC_TCE)
+
+/*-----------------------------------------------------------------------
+ * PISCR - Periodic Interrupt Status and Control 4-42
+ *-----------------------------------------------------------------------
+ * Clear Periodic Interrupt Status, Set 32KHz timersclk, and enable
+ * Periodic timer
+ */
+#define CONFIG_SYS_PISCR (PISCR_PS|PISCR_PTF|PISCR_PTE)
+
+/*-----------------------------------------------------------------------
+ * SCCR - System Clock Control 9-8
+ *-----------------------------------------------------------------------
+ */
+#define CONFIG_SYS_SCCR (SCCR_DFBRG00)
+
+/*-----------------------------------------------------------------------
+ * RCCR - RISC Controller Configuration 13-7
+ *-----------------------------------------------------------------------
+ */
+#define CONFIG_SYS_RCCR 0
+
+/*
+ * Init Memory Controller:
+ *
+ * Bank Bus Machine PortSz Device
+ * ---- --- ------- ------ ------
+ * 0 60x GPCM 64 bit FLASH
+ * 1 60x SDRAM 64 bit SDRAM
+ *
+ */
+
+ /* Initialize SDRAM on local bus
+ */
+#define CONFIG_SYS_INIT_LOCAL_SDRAM
+
+
+/* Minimum mask to separate preliminary
+ * address ranges for CS[0:2]
+ */
+#define CONFIG_SYS_MIN_AM_MASK 0xC0000000
+
+/*
+ * we use the same values for 32 MB and 128 MB SDRAM
+ * refresh rate = 7.68 uS (100 MHz Bus Clock)
+ */
+#define CONFIG_SYS_MPTPR 0x2000
+#define CONFIG_SYS_PSRT 0x16
+
+#define CONFIG_SYS_MRS_OFFS 0x00000000
+
+
+#if defined(CONFIG_BOOT_ROM)
+/*
+ * Bank 0 - Boot ROM (8 bit wide)
+ */
+#define CONFIG_SYS_BR0_PRELIM ((CONFIG_SYS_BOOTROM_BASE & BRx_BA_MSK)|\
+ BRx_PS_8 |\
+ BRx_MS_GPCM_P |\
+ BRx_V)
+
+#define CONFIG_SYS_OR0_PRELIM (P2SZ_TO_AM(CONFIG_SYS_BOOTROM_SIZE) |\
+ ORxG_CSNT |\
+ ORxG_ACS_DIV1 |\
+ ORxG_SCY_5_CLK |\
+ ORxG_EHTR |\
+ ORxG_TRLX)
+
+/*
+ * Bank 1 - Flash (64 bit wide)
+ */
+#define CONFIG_SYS_BR1_PRELIM ((CONFIG_SYS_FLASH_BASE & BRx_BA_MSK) |\
+ BRx_PS_64 |\
+ BRx_MS_GPCM_P |\
+ BRx_V)
+
+#define CONFIG_SYS_OR1_PRELIM (P2SZ_TO_AM(CONFIG_SYS_FLASH_SIZE) |\
+ ORxG_CSNT |\
+ ORxG_ACS_DIV1 |\
+ ORxG_SCY_5_CLK |\
+ ORxG_EHTR |\
+ ORxG_TRLX)
+
+#else /* ! CONFIG_BOOT_ROM */
+
+/*
+ * Bank 0 - Flash (64 bit wide)
+ */
+#define CONFIG_SYS_BR0_PRELIM ((CONFIG_SYS_FLASH_BASE & BRx_BA_MSK) |\
+ BRx_PS_64 |\
+ BRx_MS_GPCM_P |\
+ BRx_V)
+
+#define CONFIG_SYS_OR0_PRELIM (P2SZ_TO_AM(CONFIG_SYS_FLASH_SIZE) |\
+ ORxG_CSNT |\
+ ORxG_ACS_DIV1 |\
+ ORxG_SCY_5_CLK |\
+ ORxG_EHTR |\
+ ORxG_TRLX)
+
+/*
+ * Bank 1 - Disk-On-Chip
+ */
+#define CONFIG_SYS_BR1_PRELIM ((CONFIG_SYS_DOC_BASE & BRx_BA_MSK) |\
+ BRx_PS_8 |\
+ BRx_MS_GPCM_P |\
+ BRx_V)
+
+#define CONFIG_SYS_OR1_PRELIM (P2SZ_TO_AM(CONFIG_SYS_DOC_SIZE) |\
+ ORxG_CSNT |\
+ ORxG_ACS_DIV1 |\
+ ORxG_SCY_5_CLK |\
+ ORxG_EHTR |\
+ ORxG_TRLX)
+
+#endif /* CONFIG_BOOT_ROM */
+
+/* Bank 2 - SDRAM
+ */
+
+#ifndef CONFIG_SYS_RAMBOOT
+#define CONFIG_SYS_BR2_PRELIM ((CONFIG_SYS_SDRAM_BASE & BRx_BA_MSK) |\
+ BRx_PS_64 |\
+ BRx_MS_SDRAM_P |\
+ BRx_V)
+
+ /* SDRAM initialization values for 8-column chips
+ */
+#define CONFIG_SYS_OR2_8COL (CONFIG_SYS_MIN_AM_MASK |\
+ ORxS_BPD_4 |\
+ ORxS_ROWST_PBI0_A9 |\
+ ORxS_NUMR_12)
+
+#define CONFIG_SYS_PSDMR_8COL (PSDMR_SDAM_A13_IS_A5 |\
+ PSDMR_BSMA_A14_A16 |\
+ PSDMR_SDA10_PBI0_A10 |\
+ PSDMR_RFRC_7_CLK |\
+ PSDMR_PRETOACT_2W |\
+ PSDMR_ACTTORW_2W |\
+ PSDMR_LDOTOPRE_1C |\
+ PSDMR_WRC_1C |\
+ PSDMR_CL_2)
+
+ /* SDRAM initialization values for 9-column chips
+ */
+#define CONFIG_SYS_OR2_9COL (CONFIG_SYS_MIN_AM_MASK |\
+ ORxS_BPD_4 |\
+ ORxS_ROWST_PBI0_A7 |\
+ ORxS_NUMR_13)
+
+#define CONFIG_SYS_PSDMR_9COL (PSDMR_SDAM_A14_IS_A5 |\
+ PSDMR_BSMA_A13_A15 |\
+ PSDMR_SDA10_PBI0_A9 |\
+ PSDMR_RFRC_7_CLK |\
+ PSDMR_PRETOACT_2W |\
+ PSDMR_ACTTORW_2W |\
+ PSDMR_LDOTOPRE_1C |\
+ PSDMR_WRC_1C |\
+ PSDMR_CL_2)
+
+#define CONFIG_SYS_OR2_PRELIM CONFIG_SYS_OR2_9COL
+#define CONFIG_SYS_PSDMR CONFIG_SYS_PSDMR_9COL
+
+#endif /* CONFIG_SYS_RAMBOOT */
+
+#endif /* __CONFIG_H */
Code Review / kvmfornfv.git / blobdiff