--- /dev/null
+/*
+ * (C) Copyright 2001
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+/*
+ * board/config.h - configuration options, board specific
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/***********************************************************
+ * High Level Configuration Options
+ * (easy to change)
+ ***********************************************************/
+#define CONFIG_405GP 1 /* This is a PPC405 CPU */
+#define CONFIG_PIP405 1 /* ...on a PIP405 board */
+
+#define CONFIG_SYS_TEXT_BASE 0xFFF80000
+
+/***********************************************************
+ * Clock
+ ***********************************************************/
+#define CONFIG_SYS_CLK_FREQ 33000000 /* external frequency to pll */
+
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_IDE
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_PCI
+#define CONFIG_CMD_CACHE
+#define CONFIG_CMD_IRQ
+#define CONFIG_CMD_EEPROM
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_REGINFO
+#define CONFIG_CMD_FDC
+#define CONFIG_CMD_SCSI
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_DATE
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_USB
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_SDRAM
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_SAVES
+#define CONFIG_CMD_BSP
+
+#define CONFIG_SYS_HUSH_PARSER
+/**************************************************************
+ * I2C Stuff:
+ * the PIP405 is equiped with an Atmel 24C128/256 EEPROM at address
+ * 0x53.
+ * Caution: on the same bus is the SPD (Serial Presens Detect
+ * EEPROM of the SDRAM
+ * The Atmel EEPROM uses 16Bit addressing.
+ ***************************************************************/
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_PPC4XX
+#define CONFIG_SYS_I2C_PPC4XX_CH0
+#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 50000
+#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F
+
+#define CONFIG_SYS_I2C_EEPROM_ADDR 0x53
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
+#define CONFIG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */
+#define CONFIG_ENV_OFFSET 0x000 /* environment starts at the beginning of the EEPROM */
+#define CONFIG_ENV_SIZE 0x800 /* 2 kBytes may be used for env vars */
+
+#undef CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6 /* The Atmel 24C128/256 has */
+ /* 64 byte page write mode using*/
+ /* last 6 bits of the address */
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */
+
+
+/***************************************************************
+ * Definitions for Serial Presence Detect EEPROM address
+ * (to get SDRAM settings)
+ ***************************************************************/
+#define SPD_EEPROM_ADDRESS 0x50
+
+#define CONFIG_BOARD_EARLY_INIT_F
+#define CONFIG_BOARD_EARLY_INIT_R
+
+/**************************************************************
+ * Environment definitions
+ **************************************************************/
+#define CONFIG_BAUDRATE 9600 /* STD Baudrate */
+
+
+#define CONFIG_BOOTDELAY 5
+/* autoboot (do NOT change this set environment variable "bootdelay" to -1 instead) */
+/* #define CONFIG_BOOT_RETRY_TIME -10 /XXX* feature is available but not enabled */
+#define CONFIG_ZERO_BOOTDELAY_CHECK /* check console even if bootdelay = 0 */
+
+
+#define CONFIG_BOOTCOMMAND "diskboot 400000 0:1; bootm" /* autoboot command */
+#define CONFIG_BOOTARGS "console=ttyS0,9600 root=/dev/hda5" /* boot arguments */
+
+#define CONFIG_IPADDR 10.0.0.100
+#define CONFIG_SERVERIP 10.0.0.1
+#define CONFIG_PREBOOT
+/***************************************************************
+ * defines if the console is stored in the environment
+ ***************************************************************/
+#define CONFIG_SYS_CONSOLE_IS_IN_ENV /* stdin, stdout and stderr are in evironment */
+/***************************************************************
+ * defines if an overwrite_console function exists
+ *************************************************************/
+#define CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE
+#define CONFIG_SYS_CONSOLE_INFO_QUIET
+/***************************************************************
+ * defines if the overwrite_console should be stored in the
+ * environment
+ **************************************************************/
+#undef CONFIG_SYS_CONSOLE_ENV_OVERWRITE
+
+/**************************************************************
+ * loads config
+ *************************************************************/
+#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
+#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
+
+#define CONFIG_MISC_INIT_R
+/***********************************************************
+ * Miscellaneous configurable options
+ **********************************************************/
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#if defined(CONFIG_CMD_KGDB)
+#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
+#else
+#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
+#endif
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
+
+#define CONFIG_SYS_MEMTEST_START 0x0100000 /* memtest works on */
+#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 1 ... 12 MB in DRAM */
+
+#define CONFIG_CONS_INDEX 1 /* Use UART0 */
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE 1
+#define CONFIG_SYS_NS16550_CLK get_serial_clock()
+
+#undef CONFIG_SYS_EXT_SERIAL_CLOCK /* no external serial clock used */
+#define CONFIG_SYS_BASE_BAUD 691200
+
+/* The following table includes the supported baudrates */
+#define CONFIG_SYS_BAUDRATE_TABLE \
+ { 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, \
+ 57600, 115200, 230400, 460800, 921600 }
+
+#define CONFIG_SYS_LOAD_ADDR 0x400000 /* default load address */
+#define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_into (bd_t) */
+
+/*-----------------------------------------------------------------------
+ * PCI stuff
+ *-----------------------------------------------------------------------
+ */
+#define PCI_HOST_ADAPTER 0 /* configure ar pci adapter */
+#define PCI_HOST_FORCE 1 /* configure as pci host */
+#define PCI_HOST_AUTO 2 /* detected via arbiter enable */
+
+#define CONFIG_PCI /* include pci support */
+#define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */
+#define CONFIG_PCI_HOST PCI_HOST_FORCE /* configure as pci-host */
+#define CONFIG_PCI_PNP /* pci plug-and-play */
+ /* resource configuration */
+#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x0000 /* PCI Vendor ID: to-do!!! */
+#define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0x0000 /* PCI Device ID: to-do!!! */
+#define CONFIG_SYS_PCI_PTM1LA 0x00000000 /* point to sdram */
+#define CONFIG_SYS_PCI_PTM1MS 0x80000001 /* 2GB, enable hard-wired to 1 */
+#define CONFIG_SYS_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */
+#define CONFIG_SYS_PCI_PTM2LA 0x00000000 /* disabled */
+#define CONFIG_SYS_PCI_PTM2MS 0x00000000 /* disabled */
+#define CONFIG_SYS_PCI_PTM2PCI 0x00000000 /* Host: use this pci address */
+
+/*-----------------------------------------------------------------------
+ * Start addresses for the final memory configuration
+ * (Set up by the startup code)
+ * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
+ */
+#define CONFIG_SYS_SDRAM_BASE 0x00000000
+#define CONFIG_SYS_FLASH_BASE 0xFFF80000
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
+#define CONFIG_SYS_MONITOR_LEN (512 * 1024) /* Reserve 512 kB for Monitor */
+#define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserve 1024 kB for malloc() */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+/*-----------------------------------------------------------------------
+ * FLASH organization
+ */
+#define CONFIG_SYS_UPDATE_FLASH_SIZE
+#define CONFIG_SYS_FLASH_PROTECTION
+#define CONFIG_SYS_FLASH_EMPTY_INFO
+
+#define CONFIG_SYS_FLASH_CFI
+#define CONFIG_FLASH_CFI_DRIVER
+
+#define CONFIG_FLASH_SHOW_PROGRESS 45
+
+#define CONFIG_SYS_MAX_FLASH_BANKS 1
+#define CONFIG_SYS_MAX_FLASH_SECT 256
+
+/*
+ * Init Memory Controller:
+ */
+#define FLASH_MAX_SIZE 0x00800000 /* 8MByte max */
+#define FLASH_BASE_PRELIM 0xFF800000 /* open the flash CS */
+/* Size: 0=1MB, 1=2MB, 2=4MB, 3=8MB, 4=16MB, 5=32MB, 6=64MB, 7=128MB */
+#define FLASH_SIZE_PRELIM 3 /* maximal flash FLASH size bank #0 */
+
+#define CONFIG_BOARD_EARLY_INIT_F
+
+/* Configuration Port location */
+#define CONFIG_PORT_ADDR 0xF4000000
+#define MULTI_PURPOSE_SOCKET_ADDR 0xF8000000
+
+
+/*-----------------------------------------------------------------------
+ * Definitions for initial stack pointer and data area (in On Chip SRAM)
+ */
+#define CONFIG_SYS_TEMP_STACK_OCM 1
+#define CONFIG_SYS_OCM_DATA_ADDR 0xF0000000
+#define CONFIG_SYS_OCM_DATA_SIZE 0x1000
+#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_DATA_ADDR /* inside of On Chip SRAM */
+#define CONFIG_SYS_INIT_RAM_SIZE CONFIG_SYS_OCM_DATA_SIZE /* Size of On Chip SRAM */
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
+
+/***********************************************************************
+ * External peripheral base address
+ ***********************************************************************/
+#define CONFIG_SYS_ISA_IO_BASE_ADDRESS 0xE8000000
+
+/***********************************************************************
+ * Last Stage Init
+ ***********************************************************************/
+#define CONFIG_LAST_STAGE_INIT
+/************************************************************
+ * Ethernet Stuff
+ ***********************************************************/
+#define CONFIG_PPC4xx_EMAC
+#define CONFIG_MII 1 /* MII PHY management */
+#define CONFIG_PHY_ADDR 1 /* PHY address */
+/************************************************************
+ * RTC
+ ***********************************************************/
+#define CONFIG_RTC_MC146818
+#undef CONFIG_WATCHDOG /* watchdog disabled */
+
+/************************************************************
+ * IDE/ATA stuff
+ ************************************************************/
+#define CONFIG_SYS_IDE_MAXBUS 2 /* max. 2 IDE busses */
+#define CONFIG_SYS_IDE_MAXDEVICE (CONFIG_SYS_IDE_MAXBUS*2) /* max. 2 drives per IDE bus */
+
+#define CONFIG_SYS_ATA_BASE_ADDR CONFIG_SYS_ISA_IO_BASE_ADDRESS /* base address */
+#define CONFIG_SYS_ATA_IDE0_OFFSET 0x01F0 /* ide0 offste */
+#define CONFIG_SYS_ATA_IDE1_OFFSET 0x0170 /* ide1 offset */
+#define CONFIG_SYS_ATA_DATA_OFFSET 0 /* data reg offset */
+#define CONFIG_SYS_ATA_REG_OFFSET 0 /* reg offset */
+#define CONFIG_SYS_ATA_ALT_OFFSET 0x200 /* alternate register offset */
+
+#undef CONFIG_IDE_8xx_DIRECT /* no pcmcia interface required */
+#undef CONFIG_IDE_LED /* no led for ide supported */
+#define CONFIG_IDE_RESET /* reset for ide supported... */
+#define CONFIG_IDE_RESET_ROUTINE /* with a special reset function */
+#define CONFIG_SUPPORT_VFAT
+
+/************************************************************
+ * ATAPI support (experimental)
+ ************************************************************/
+#define CONFIG_ATAPI /* enable ATAPI Support */
+
+/************************************************************
+ * SCSI support (experimental) only SYM53C8xx supported
+ ************************************************************/
+#define CONFIG_SCSI_SYM53C8XX
+#define CONFIG_SYS_SCSI_MAX_LUN 8 /* number of supported LUNs */
+#define CONFIG_SYS_SCSI_MAX_SCSI_ID 7 /* maximum SCSI ID (0..6) */
+#define CONFIG_SYS_SCSI_MAX_DEVICE CONFIG_SYS_SCSI_MAX_SCSI_ID * CONFIG_SYS_SCSI_MAX_LUN /* maximum Target devices */
+#define CONFIG_SYS_SCSI_SPIN_UP_TIME 2
+
+/************************************************************
+ * Disk-On-Chip configuration
+ ************************************************************/
+#define CONFIG_SYS_MAX_DOC_DEVICE 1 /* Max number of DOC devices */
+#define CONFIG_SYS_DOC_SHORT_TIMEOUT
+#define CONFIG_SYS_DOC_SUPPORT_2000
+#define CONFIG_SYS_DOC_SUPPORT_MILLENNIUM
+
+/************************************************************
+ * DISK Partition support
+ ************************************************************/
+#define CONFIG_DOS_PARTITION
+#define CONFIG_MAC_PARTITION
+#define CONFIG_ISO_PARTITION /* Experimental */
+
+/************************************************************
+ * Keyboard support
+ ************************************************************/
+#define CONFIG_ISA_KEYBOARD
+
+/************************************************************
+ * Video support
+ ************************************************************/
+#define CONFIG_VIDEO /*To enable video controller support */
+#define CONFIG_VIDEO_CT69000
+#define CONFIG_CFB_CONSOLE
+#define CONFIG_VIDEO_LOGO
+#define CONFIG_CONSOLE_EXTRA_INFO
+#define CONFIG_VGA_AS_SINGLE_DEVICE
+#define CONFIG_VIDEO_SW_CURSOR
+#define CONFIG_VIDEO_ONBOARD /* Video controller is on-board */
+
+/************************************************************
+ * USB support
+ ************************************************************/
+#define CONFIG_USB_UHCI
+#define CONFIG_USB_KEYBOARD
+#define CONFIG_USB_STORAGE
+
+/* Enable needed helper functions */
+#define CONFIG_SYS_STDIO_DEREGISTER /* needs stdio_deregister */
+
+/************************************************************
+ * Debug support
+ ************************************************************/
+#if defined(CONFIG_CMD_KGDB)
+#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
+#endif
+
+/************************************************************
+ * support BZIP2 compression
+ ************************************************************/
+#define CONFIG_BZIP2 1
+
+/************************************************************
+ * Ident
+ ************************************************************/
+#define VERSION_TAG "released"
+#define CONFIG_ISO_STRING "MEV-10066-001"
+#define CONFIG_IDENT_STRING "\n(c) 2002 by MPL AG Switzerland, " CONFIG_ISO_STRING " " VERSION_TAG
+
+
+#endif /* __CONFIG_H */
Code Review / kvmfornfv.git / blobdiff