--- /dev/null
+/*
+ * (C) Copyright 2003
+ * Denis Peter d.peter@mpl.ch
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+/*
+ * File: PATI.h
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ */
+
+#define CONFIG_MPC555 1 /* This is an MPC555 CPU */
+#define CONFIG_PATI 1 /* ...On a PATI board */
+
+#define CONFIG_SYS_TEXT_BASE 0xFFF00000
+
+/* Serial Console Configuration */
+#define CONFIG_5xx_CONS_SCI1
+#undef CONFIG_5xx_CONS_SCI2
+
+#define CONFIG_BAUDRATE 9600
+
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+
+/*
+ * Command line configuration.
+ */
+#define CONFIG_CMD_MEMORY
+#define CONFIG_CMD_LOADB
+#define CONFIG_CMD_REGINFO
+#define CONFIG_CMD_FLASH
+#define CONFIG_CMD_LOADS
+#define CONFIG_CMD_SAVEENV
+#define CONFIG_CMD_REGINFO
+#define CONFIG_CMD_BDI
+#define CONFIG_CMD_CONSOLE
+#define CONFIG_CMD_RUN
+#define CONFIG_CMD_BSP
+#define CONFIG_CMD_IMI
+#define CONFIG_CMD_EEPROM
+#define CONFIG_CMD_IRQ
+#define CONFIG_CMD_MISC
+
+
+#if 0
+#define CONFIG_BOOTDELAY -1 /* autoboot disabled */
+#else
+#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
+#endif
+#define CONFIG_BOOTCOMMAND "" /* autoboot command */
+
+#define CONFIG_BOOTARGS "" /* */
+
+#define CONFIG_WATCHDOG /* turn on platform specific watchdog */
+
+/*#define CONFIG_STATUS_LED 1 */ /* Enable status led */
+
+#define CONFIG_LOADS_ECHO 1 /* Echo on for serial download */
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CONFIG_SYS_CONSOLE_IS_IN_ENV /* stdin, stdout and stderr are in evironment */
+#define CONFIG_PREBOOT
+
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#define CONFIG_SYS_PROMPT "pati=> " /* Monitor Command Prompt */
+#if defined(CONFIG_CMD_KGDB)
+#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
+#else
+#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
+#endif
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
+
+#define CONFIG_SYS_MEMTEST_START 0x00010000 /* memtest works on */
+#define CONFIG_SYS_MEMTEST_END 0x00A00000 /* 10 MB in SRAM */
+
+#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
+
+#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 1250000 }
+
+
+/***********************************************************************
+ * Last Stage Init
+ ***********************************************************************/
+#define CONFIG_LAST_STAGE_INIT
+
+/*
+ * Low Level Configuration Settings
+ */
+
+/*
+ * Internal Memory Mapped (This is not the IMMR content)
+ */
+#define CONFIG_SYS_IMMR 0x01C00000 /* Physical start adress of internal memory map */
+
+/*
+ * Definitions for initial stack pointer and data area
+ */
+#define CONFIG_SYS_INIT_RAM_ADDR (CONFIG_SYS_IMMR + 0x003f9800) /* Physical start adress of internal MPC555 writable RAM */
+#define CONFIG_SYS_INIT_RAM_SIZE (CONFIG_SYS_IMMR + 0x003fffff) /* Physical end adress of internal MPC555 used RAM area */
+#define CONFIG_SYS_GBL_DATA_OFFSET ((CONFIG_SYS_INIT_RAM_SIZE - CONFIG_SYS_INIT_RAM_ADDR) - GENERATED_GBL_DATA_SIZE) /* Offset from the beginning of ram */
+#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_IMMR + 0x03fa000) /* Physical start adress of inital stack */
+/*
+ * Start addresses for the final memory configuration
+ * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
+ */
+#define CONFIG_SYS_SDRAM_BASE 0x00000000 /* Monitor won't change memory map */
+#define CONFIG_SYS_FLASH_BASE 0xffC00000 /* External flash */
+#define PCI_BASE 0x03000000 /* PCI Base (CS2) */
+#define PCI_CONFIG_BASE 0x04000000 /* PCI & PLD (CS3) */
+#define PLD_CONFIG_BASE 0x04001000 /* PLD (CS3) */
+
+#define CONFIG_SYS_MONITOR_BASE 0xFFF00000
+/* CONFIG_SYS_FLASH_BASE */ /* CONFIG_SYS_TEXT_BASE is defined in the board config.mk file. */
+ /* This adress is given to the linker with -Ttext to */
+ /* locate the text section at this adress. */
+#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 192 kB for Monitor */
+#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
+
+#define CONFIG_SYS_RESET_ADDRESS (PLD_CONFIG_BASE + 0x10) /* Adress which causes reset */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+
+
+/*-----------------------------------------------------------------------
+ * FLASH organization
+ *-----------------------------------------------------------------------
+ *
+ */
+
+#define CONFIG_SYS_FLASH_PROTECTION
+#define CONFIG_SYS_FLASH_EMPTY_INFO
+
+#define CONFIG_SYS_FLASH_CFI
+#define CONFIG_FLASH_CFI_DRIVER
+
+#define CONFIG_FLASH_SHOW_PROGRESS 45
+
+#define CONFIG_SYS_MAX_FLASH_BANKS 1
+#define CONFIG_SYS_MAX_FLASH_SECT 128
+
+#define CONFIG_ENV_IS_IN_EEPROM
+#ifdef CONFIG_ENV_IS_IN_EEPROM
+#define CONFIG_ENV_OFFSET 0
+#define CONFIG_ENV_SIZE 2048
+#endif
+
+#undef CONFIG_ENV_IS_IN_FLASH
+#ifdef CONFIG_ENV_IS_IN_FLASH
+#define CONFIG_ENV_SIZE 0x00002000 /* Set whole sector as env */
+#define CONFIG_ENV_OFFSET ((0 - CONFIG_SYS_FLASH_BASE) - CONFIG_ENV_SIZE) /* Environment starts at this adress */
+#endif
+
+
+#define CONFIG_SPI 1
+#define CONFIG_SYS_SPI_CS_USED 0x09 /* CS0 and CS3 are used */
+#define CONFIG_SYS_SPI_CS_BASE 0x08 /* CS3 is active low */
+#define CONFIG_SYS_SPI_CS_ACT 0x00 /* CS3 is active low */
+/*-----------------------------------------------------------------------
+ * SYPCR - System Protection Control
+ * SYPCR can only be written once after reset!
+ *-----------------------------------------------------------------------
+ * SW Watchdog freeze
+ */
+#undef CONFIG_WATCHDOG
+#if defined(CONFIG_WATCHDOG)
+#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
+ SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP)
+#else
+#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
+ SYPCR_SWP)
+#endif /* CONFIG_WATCHDOG */
+
+/*-----------------------------------------------------------------------
+ * TBSCR - Time Base Status and Control
+ *-----------------------------------------------------------------------
+ * Clear Reference Interrupt Status, Timebase freezing enabled
+ */
+#define CONFIG_SYS_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF)
+
+/*-----------------------------------------------------------------------
+ * PISCR - Periodic Interrupt Status and Control
+ *-----------------------------------------------------------------------
+ * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
+ */
+#define CONFIG_SYS_PISCR (PISCR_PS | PISCR_PITF)
+
+/*-----------------------------------------------------------------------
+ * SCCR - System Clock and reset Control Register
+ *-----------------------------------------------------------------------
+ * Set clock output, timebase and RTC source and divider,
+ * power management and some other internal clocks
+ */
+#define SCCR_MASK SCCR_EBDF00
+#define CONFIG_SYS_SCCR (SCCR_TBS | SCCR_RTDIV | SCCR_RTSEL | \
+ SCCR_COM01 | SCCR_DFNL000 | SCCR_DFNH000)
+
+/*-----------------------------------------------------------------------
+ * SIUMCR - SIU Module Configuration
+ *-----------------------------------------------------------------------
+ * Data show cycle
+ */
+#define CONFIG_SYS_SIUMCR (SIUMCR_DBGC00 | SIUMCR_EARB | SIUMCR_GPC01 | SIUMCR_MLRC11) /* Disable data show cycle */
+
+/*-----------------------------------------------------------------------
+ * PLPRCR - PLL, Low-Power, and Reset Control Register
+ *-----------------------------------------------------------------------
+ * Set all bits to 40 Mhz
+ *
+ */
+#define CONFIG_SYS_OSC_CLK ((uint)4000000) /* Oscillator clock is 4MHz */
+
+
+#define CONFIG_SYS_PLPRCR (PLPRCR_MF_9 | PLPRCR_DIVF_0)
+
+/*-----------------------------------------------------------------------
+ * UMCR - UIMB Module Configuration Register
+ *-----------------------------------------------------------------------
+ *
+ */
+#define CONFIG_SYS_UMCR (UMCR_FSPEED) /* IMB clock same as U-bus */
+
+/*-----------------------------------------------------------------------
+ * ICTRL - I-Bus Support Control Register
+ */
+#define CONFIG_SYS_ICTRL (ICTRL_ISCT_SER_7) /* Take out of serialized mode */
+
+/*-----------------------------------------------------------------------
+ * USIU - Memory Controller Register
+ *-----------------------------------------------------------------------
+ */
+#define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE | BR_V | BR_BI | BR_PS_16 | BR_SETA)
+#define CONFIG_SYS_OR0_PRELIM (0xffc00000) /* SCY is not used if external TA is set */
+/* SDRAM */
+#define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_SDRAM_BASE | BR_V | BR_BI | BR_PS_32 | BR_SETA)
+#define CONFIG_SYS_OR1_PRELIM (OR_ADDR_MK_FF) /* SCY is not used if external TA is set */
+/* PCI */
+#define CONFIG_SYS_BR2_PRELIM (PCI_BASE | BR_V | BR_PS_32 | BR_SETA)
+#define CONFIG_SYS_OR2_PRELIM (OR_ADDR_MK_FF)
+/* config registers: */
+#define CONFIG_SYS_BR3_PRELIM (PCI_CONFIG_BASE | BR_V | BR_BI | BR_PS_32 | BR_SETA)
+#define CONFIG_SYS_OR3_PRELIM (0xffff0000)
+
+#define FLASH_BASE0_PRELIM CONFIG_SYS_FLASH_BASE /* We don't realign the flash */
+
+/*-----------------------------------------------------------------------
+ * DER - Timer Decrementer
+ *-----------------------------------------------------------------------
+ * Initialise to zero
+ */
+#define CONFIG_SYS_DER 0x00000000
+
+#define VERSION_TAG "released"
+#define CONFIG_ISO_STRING "MEV-10084-001"
+
+#define CONFIG_IDENT_STRING "\n(c) 2003 by MPL AG Switzerland, " CONFIG_ISO_STRING " " VERSION_TAG
+
+#endif /* __CONFIG_H */
Code Review / kvmfornfv.git / blobdiff