--- /dev/null
+/*
+ * Copyright 2009-2010,2012 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/* The P2020COME board is only booted via the Freescale On-Chip ROM */
+#define CONFIG_SYS_RAMBOOT
+#define CONFIG_SYS_EXTRA_ENV_RELOC
+
+#define CONFIG_SYS_TEXT_BASE 0xf8f80000
+#define CONFIG_RESET_VECTOR_ADDRESS 0xf8fffffc
+
+#ifdef CONFIG_SDCARD
+#define CONFIG_RAMBOOT_SDCARD 1
+#endif
+
+#ifdef CONFIG_SPIFLASH
+#define CONFIG_RAMBOOT_SPIFLASH 1
+#endif
+
+#ifndef CONFIG_SYS_MONITOR_BASE
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
+#endif
+
+/* High Level Configuration Options */
+#define CONFIG_BOOKE 1 /* BOOKE */
+#define CONFIG_E500 1 /* BOOKE e500 family */
+#define CONFIG_P2020 1
+#define CONFIG_P2020COME 1
+#define CONFIG_FSL_ELBC 1 /* Enable eLBC Support */
+#define CONFIG_MP
+
+#define CONFIG_PCI 1 /* Enable PCI/PCIE */
+#if defined(CONFIG_PCI)
+#define CONFIG_PCIE1 1 /* PCIE controller 1 (slot 1) */
+#define CONFIG_PCIE2 1 /* PCIE controller 2 (slot 2) */
+#define CONFIG_PCIE3 1 /* PCIE controller 3 (slot 3) */
+
+#define CONFIG_FSL_PCI_INIT 1 /* Use common FSL init code */
+#define CONFIG_PCI_INDIRECT_BRIDGE 1 /* indirect PCI bridge support */
+#define CONFIG_FSL_PCIE_RESET 1 /* need PCIe reset errata */
+#define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */
+#endif /* #if defined(CONFIG_PCI) */
+#define CONFIG_FSL_LAW 1 /* Use common FSL init code */
+#define CONFIG_TSEC_ENET /* tsec ethernet support */
+#define CONFIG_ENV_OVERWRITE
+
+#if defined(CONFIG_PCI)
+#define CONFIG_E1000 1 /* E1000 pci Ethernet card */
+#endif
+
+#ifndef __ASSEMBLY__
+extern unsigned long get_board_ddr_clk(unsigned long dummy);
+extern unsigned long get_board_sys_clk(unsigned long dummy);
+#endif
+
+/*
+ * For P2020COME DDRCLK and SYSCLK are from the same oscillator
+ * For DA phase the SYSCLK is 66MHz
+ * For EA phase the SYSCLK is 100MHz
+ */
+#define CONFIG_DDR_CLK_FREQ get_board_ddr_clk(0)
+#define CONFIG_SYS_CLK_FREQ get_board_sys_clk(0)
+
+#define CONFIG_HWCONFIG
+
+/*
+ * These can be toggled for performance analysis, otherwise use default.
+ */
+#define CONFIG_L2_CACHE /* toggle L2 cache */
+#define CONFIG_BTB /* toggle branch prediction */
+
+#define CONFIG_ADDR_STREAMING /* toggle addr streaming */
+
+#define CONFIG_ENABLE_36BIT_PHYS 1
+
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_ADDR_MAP 1
+#define CONFIG_SYS_NUM_ADDR_MAP 16 /* number of TLB1 entries */
+#endif
+
+#define CONFIG_SYS_MEMTEST_START 0x00000000 /* memtest works on */
+#define CONFIG_SYS_MEMTEST_END 0x1fffffff
+#define CONFIG_PANIC_HANG /* do not reset board on panic */
+
+ /*
+ * Config the L2 Cache as L2 SRAM
+ */
+#define CONFIG_SYS_INIT_L2_ADDR 0xf8f80000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_INIT_L2_ADDR_PHYS 0xff8f80000ull
+#else
+#define CONFIG_SYS_INIT_L2_ADDR_PHYS CONFIG_SYS_INIT_L2_ADDR
+#endif
+#define CONFIG_SYS_L2_SIZE (512 << 10)
+#define CONFIG_SYS_INIT_L2_END (CONFIG_SYS_INIT_L2_ADDR \
+ + CONFIG_SYS_L2_SIZE)
+
+#define CONFIG_SYS_CCSRBAR 0xffe00000
+#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR
+
+/* DDR Setup */
+#define CONFIG_SYS_FSL_DDR3
+#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */
+#define CONFIG_DDR_SPD
+
+#define CONFIG_DDR_ECC
+#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
+#define CONFIG_MEM_INIT_VALUE 0xdeadbeef
+
+#define CONFIG_SYS_SDRAM_SIZE 2048ULL /* DDR size on P2020COME */
+#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000
+#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
+
+#define CONFIG_NUM_DDR_CONTROLLERS 1
+#define CONFIG_DIMM_SLOTS_PER_CTLR 1
+#define CONFIG_CHIP_SELECTS_PER_CTRL 2
+
+#define CONFIG_SYS_DDR_ERR_INT_EN 0x0000000d
+#define CONFIG_SYS_DDR_ERR_DIS 0x00000000
+#define CONFIG_SYS_DDR_SBE 0x00ff0000
+
+#define CONFIG_SYS_SPD_BUS_NUM 1
+#define SPD_EEPROM_ADDRESS 0x53
+
+/*
+ * Memory map
+ *
+ * 0x0000_0000 0x7fff_ffff DDR3 2G Cacheable
+ * 0x8000_0000 0x9fff_ffff PCI Express 3 Mem 1G non-cacheable
+ * 0xa000_0000 0xbfff_ffff PCI Express 2 Mem 1G non-cacheable
+ * 0xc000_0000 0xdfff_ffff PCI Express 1 Mem 1G non-cacheable
+ * 0xffc1_0000 0xffc1_ffff PCI Express 3 IO 64K non-cacheable
+ * 0xffc2_0000 0xffc2_ffff PCI Express 2 IO 64K non-cacheable
+ * 0xffc3_0000 0xffc3_ffff PCI Express 1 IO 64K non-cacheable
+ *
+ * 0xffd0_0000 0xffd0_3fff L1 for stack 16K Cacheable TLB0
+ * 0xffe0_0000 0xffef_ffff CCSR 1M non-cacheable
+ */
+
+/*
+ * Local Bus Definitions
+ */
+
+/* There is no NOR Flash on P2020COME */
+#define CONFIG_SYS_NO_FLASH
+
+#define CONFIG_BOARD_EARLY_INIT_R /* call board_early_init_r function */
+#define CONFIG_HWCONFIG
+
+#define CONFIG_SYS_INIT_RAM_LOCK 1
+#define CONFIG_SYS_INIT_RAM_ADDR 0xffd00000 /* stack in RAM */
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR
+/* the assembler doesn't like typecast */
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS \
+ ((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \
+ CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW)
+#else
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS CONFIG_SYS_INIT_RAM_ADDR
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR_PHYS
+#endif
+#define CONFIG_SYS_INIT_RAM_SIZE 0x00004000
+
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE \
+ - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
+
+#define CONFIG_SYS_MONITOR_LEN (256 * 1024)
+#define CONFIG_SYS_MALLOC_LEN (1024 * 1024)
+
+/* Serial Port - controlled on board with jumper J8
+ * open - index 2
+ * shorted - index 1
+ */
+#define CONFIG_CONS_INDEX 1
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE 1
+#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
+
+#define CONFIG_SYS_CONSOLE_IS_IN_ENV /* determine from environment */
+
+#define CONFIG_SYS_BAUDRATE_TABLE \
+ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
+
+#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500)
+#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600)
+
+/* Use the HUSH parser */
+#define CONFIG_SYS_HUSH_PARSER
+
+/*
+ * Pass open firmware flat tree
+ */
+#define CONFIG_OF_LIBFDT 1
+#define CONFIG_OF_BOARD_SETUP 1
+#define CONFIG_OF_STDOUT_VIA_ALIAS 1
+
+/* new uImage format support */
+#define CONFIG_FIT 1
+#define CONFIG_FIT_VERBOSE 1
+
+/* I2C */
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_FSL
+#define CONFIG_SYS_FSL_I2C_SPEED 400000
+#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
+#define CONFIG_SYS_FSL_I2C2_SPEED 400000
+#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100
+#define CONFIG_SYS_I2C_NOPROBES { {0, 0x29} }
+
+/*
+ * I2C2 EEPROM
+ */
+#define CONFIG_ID_EEPROM
+#ifdef CONFIG_ID_EEPROM
+#define CONFIG_SYS_I2C_EEPROM_NXID
+#endif
+#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50
+#define CONFIG_SYS_I2C_EEPROM_ADDR2 0x18
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
+#define CONFIG_SYS_EEPROM_BUS_NUM 0
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */
+
+/*
+ * eSPI - Enhanced SPI
+ */
+#define CONFIG_FSL_ESPI
+#define CONFIG_SPI_FLASH
+#define CONFIG_SPI_FLASH_STMICRO
+#define CONFIG_CMD_SF
+#define CONFIG_SF_DEFAULT_SPEED 10000000
+#define CONFIG_SF_DEFAULT_MODE SPI_MODE_0
+
+/*
+ * General PCI
+ * Memory space is mapped 1-1, but I/O space must start from 0.
+ */
+#if defined(CONFIG_PCI)
+
+/* controller 3, Slot 3, tgtid 3, Base address 8000 */
+#define CONFIG_SYS_PCIE3_MEM_VIRT 0x80000000
+#define CONFIG_SYS_PCIE3_MEM_BUS 0x80000000
+#define CONFIG_SYS_PCIE3_MEM_PHYS 0x80000000
+#define CONFIG_SYS_PCIE3_MEM_SIZE 0x20000000 /* 512M */
+#define CONFIG_SYS_PCIE3_IO_VIRT 0xffc10000
+#define CONFIG_SYS_PCIE3_IO_BUS 0x00000000
+#define CONFIG_SYS_PCIE3_IO_PHYS 0xffc10000
+#define CONFIG_SYS_PCIE3_IO_SIZE 0x00010000 /* 64k */
+
+/* controller 2, Slot 2, tgtid 2, Base address 9000 */
+#define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000
+#define CONFIG_SYS_PCIE2_MEM_BUS 0xa0000000
+#define CONFIG_SYS_PCIE2_MEM_PHYS 0xa0000000
+#define CONFIG_SYS_PCIE2_MEM_SIZE 0x20000000 /* 512M */
+#define CONFIG_SYS_PCIE2_IO_VIRT 0xffc20000
+#define CONFIG_SYS_PCIE2_IO_BUS 0x00000000
+#define CONFIG_SYS_PCIE2_IO_PHYS 0xffc20000
+#define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */
+
+/* controller 1, Slot 1, tgtid 1, Base address a000 */
+#define CONFIG_SYS_PCIE1_MEM_VIRT 0xc0000000
+#define CONFIG_SYS_PCIE1_MEM_BUS 0xc0000000
+#define CONFIG_SYS_PCIE1_MEM_PHYS 0xc0000000
+#define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */
+#define CONFIG_SYS_PCIE1_IO_VIRT 0xffc30000
+#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000
+#define CONFIG_SYS_PCIE1_IO_PHYS 0xffc30000
+#define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */
+
+#define CONFIG_PCI_PNP /* do pci plug-and-play */
+
+#undef CONFIG_EEPRO100
+#undef CONFIG_TULIP
+#undef CONFIG_RTL8139
+
+#ifdef CONFIG_RTL8139
+/* This macro is used by RTL8139 but not defined in PPC architecture */
+#define KSEG1ADDR(x) (x)
+#define _IO_BASE 0x00000000
+#endif
+
+#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
+#define CONFIG_DOS_PARTITION
+
+#endif /* CONFIG_PCI */
+
+#if defined(CONFIG_TSEC_ENET)
+#define CONFIG_MII 1 /* MII PHY management */
+#define CONFIG_MII_DEFAULT_TSEC 1 /* Allow unregistered phys */
+#define CONFIG_TSEC1 1
+#define CONFIG_TSEC1_NAME "eTSEC1"
+#define CONFIG_TSEC2 1
+#define CONFIG_TSEC2_NAME "eTSEC2"
+#define CONFIG_TSEC3 1
+#define CONFIG_TSEC3_NAME "eTSEC3"
+
+#define TSEC1_PHY_ADDR 0
+#define TSEC2_PHY_ADDR 2
+#define TSEC3_PHY_ADDR 1
+
+#undef CONFIG_VSC7385_ENET
+
+#define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
+#define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
+#define TSEC3_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
+
+#define TSEC1_PHYIDX 0
+#define TSEC2_PHYIDX 0
+#define TSEC3_PHYIDX 0
+
+#define CONFIG_ETHPRIME "eTSEC1"
+
+#define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */
+
+#endif /* CONFIG_TSEC_ENET */
+
+/*
+ * Environment
+ */
+#if defined(CONFIG_RAMBOOT_SDCARD)
+ #define CONFIG_ENV_IS_IN_MMC 1
+ #define CONFIG_FSL_FIXED_MMC_LOCATION
+ #define CONFIG_ENV_SIZE 0x2000
+ #define CONFIG_SYS_MMC_ENV_DEV 0
+#elif defined(CONFIG_RAMBOOT_SPIFLASH)
+ #define CONFIG_ENV_IS_IN_SPI_FLASH
+ #define CONFIG_ENV_SPI_BUS 0
+ #define CONFIG_ENV_SPI_CS 0
+ #define CONFIG_ENV_SPI_MAX_HZ 10000000
+ #define CONFIG_ENV_SPI_MODE 0
+ #define CONFIG_ENV_OFFSET 0x100000 /* 1MB */
+ #define CONFIG_ENV_SECT_SIZE 0x10000
+ #define CONFIG_ENV_SIZE 0x2000
+#endif
+
+#define CONFIG_LOADS_ECHO 1
+#define CONFIG_SYS_LOADS_BAUD_CHANGE 1
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_IRQ
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_SETEXPR
+#define CONFIG_CMD_REGINFO
+
+#if defined(CONFIG_PCI)
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_PCI
+#endif
+
+#undef CONFIG_WATCHDOG /* watchdog disabled */
+
+#define CONFIG_MMC 1
+
+#ifdef CONFIG_MMC
+#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */
+#define CONFIG_CMD_MMC
+#define CONFIG_DOS_PARTITION
+#define CONFIG_FSL_ESDHC
+#define CONFIG_GENERIC_MMC
+#define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR
+#define CONFIG_SYS_FSL_ESDHC_BROKEN_TIMEOUT
+#endif /* CONFIG_MMC */
+
+#define CONFIG_HAS_FSL_DR_USB
+#ifdef CONFIG_HAS_FSL_DR_USB
+#define CONFIG_USB_EHCI
+
+#ifdef CONFIG_USB_EHCI
+#define CONFIG_CMD_USB
+#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
+#define CONFIG_USB_EHCI_FSL
+#define CONFIG_USB_STORAGE
+#endif
+#endif
+
+#if defined(CONFIG_MMC) || defined(CONFIG_USB_EHCI)
+#define CONFIG_CMD_EXT2
+#define CONFIG_CMD_FAT
+#define CONFIG_DOS_PARTITION
+#endif
+
+/* Misc Extra Settings */
+#define CONFIG_CMD_DHCP 1
+
+#define CONFIG_CMD_DATE 1
+#define CONFIG_RTC_M41T62 1
+#define CONFIG_SYS_RTC_BUS_NUM 1
+#define CONFIG_SYS_I2C_RTC_ADDR 0x68
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#define CONFIG_CMDLINE_EDITING /* Command-line editing */
+#define CONFIG_AUTO_COMPLETE 1 /* add autocompletion support */
+#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
+#if defined(CONFIG_CMD_KGDB)
+#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
+#else
+#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
+#endif
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
+ /* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE/* Boot Argument Buffer Size */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 64 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_SYS_BOOTMAPSZ (64 << 20)
+#define CONFIG_SYS_BOOTM_LEN (64 << 20)
+
+#if defined(CONFIG_CMD_KGDB)
+#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
+#endif
+
+/*
+ * Environment Configuration
+ */
+
+/* The mac addresses for all ethernet interface */
+#if defined(CONFIG_TSEC_ENET)
+#define CONFIG_HAS_ETH0
+#define CONFIG_HAS_ETH1
+#define CONFIG_HAS_ETH2
+#define CONFIG_HAS_ETH3
+#endif
+
+#define CONFIG_HOSTNAME unknown
+#define CONFIG_ROOTPATH "/opt/nfsroot"
+#define CONFIG_BOOTFILE "uImage"
+#define CONFIG_UBOOTPATH u-boot.bin
+
+/* default location for tftp and bootm */
+#define CONFIG_LOADADDR 1000000
+
+#define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */
+#undef CONFIG_BOOTARGS /* the boot command will set bootargs */
+
+#define CONFIG_BAUDRATE 115200
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "hwconfig=fsl_ddr:ecc=on\0" \
+ "bootcmd=run sdboot\0" \
+ "sdboot=setenv bootargs root=/dev/mmcblk0p2 rw " \
+ "rootdelay=$rootdelaysecond console=$consoledev,$baudrate "\
+ "$othbootargs; mmcinfo; " \
+ "ext2load mmc 0:2 $loadaddr /boot/$bootfile; " \
+ "ext2load mmc 0:2 $fdtaddr /boot/$fdtfile; " \
+ "bootm $loadaddr - $fdtaddr\0" \
+ "sdfatboot=setenv bootargs root=/dev/ram rw " \
+ "rootdelay=$rootdelaysecond console=$consoledev,$baudrate "\
+ "$othbootargs; mmcinfo; " \
+ "fatload mmc 0:1 $loadaddr $bootfile; " \
+ "fatload mmc 0:1 $fdtaddr $fdtfile; " \
+ "fatload mmc 0:1 $ramdiskaddr $ramdiskfile; " \
+ "bootm $loadaddr $ramdiskaddr $fdtaddr\0" \
+ "usbboot=setenv bootargs root=/dev/sda1 rw " \
+ "rootdelay=$rootdelaysecond console=$consoledev,$baudrate "\
+ "$othbootargs; " \
+ "usb start; " \
+ "ext2load usb 0:1 $loadaddr /boot/$bootfile; " \
+ "ext2load usb 0:1 $fdtaddr /boot/$fdtfile; " \
+ "bootm $loadaddr - $fdtaddr\0" \
+ "usbfatboot=setenv bootargs root=/dev/ram rw " \
+ "console=$consoledev,$baudrate $othbootargs; " \
+ "usb start; " \
+ "fatload usb 0:2 $loadaddr $bootfile; " \
+ "fatload usb 0:2 $fdtaddr $fdtfile; " \
+ "fatload usb 0:2 $ramdiskaddr $ramdiskfile; " \
+ "bootm $loadaddr $ramdiskaddr $fdtaddr\0" \
+ "usbext2boot=setenv bootargs root=/dev/ram rw " \
+ "console=$consoledev,$baudrate $othbootargs; " \
+ "usb start; " \
+ "ext2load usb 0:4 $loadaddr $bootfile; " \
+ "ext2load usb 0:4 $fdtaddr $fdtfile; " \
+ "ext2load usb 0:4 $ramdiskaddr $ramdiskfile; " \
+ "bootm $loadaddr $ramdiskaddr $fdtaddr\0" \
+ "upgradespi=sf probe 0; " \
+ "setenv startaddr 0; " \
+ "setenv erasesize a0000; " \
+ "tftp 1000000 $tftppath/$uboot_spi; " \
+ "sf erase $startaddr $erasesize; " \
+ "sf write 1000000 $startaddr $filesize; " \
+ "sf erase 100000 120000\0" \
+ "clearspienv=sf probe 0;sf erase 100000 20000\0" \
+ "othbootargs=ramdisk_size=700000 cache-sram-size=0x10000\0" \
+ "netdev=eth0\0" \
+ "rootdelaysecond=15\0" \
+ "uboot_nor=u-boot-nor.bin\0" \
+ "uboot_spi=u-boot-p2020.spi\0" \
+ "uboot_sd=u-boot-p2020.bin\0" \
+ "consoledev=ttyS0\0" \
+ "ramdiskaddr=2000000\0" \
+ "ramdiskfile=rootfs-dev.ext2.img\0" \
+ "fdtaddr=c00000\0" \
+ "fdtfile=uImage-2.6.32-p2020.dtb\0" \
+ "tftppath=p2020\0"
+
+#define CONFIG_HDBOOT \
+ "setenv bootargs root=/dev/$bdev rw rootdelay=30 " \
+ "console=$consoledev,$baudrate $othbootargs;" \
+ "usb start;" \
+ "ext2load usb 0:1 $loadaddr /boot/$bootfile;" \
+ "ext2load usb 0:1 $fdtaddr /boot/$fdtfile;" \
+ "bootm $loadaddr - $fdtaddr"
+
+#define CONFIG_NFSBOOTCOMMAND \
+ "setenv bootargs root=/dev/nfs rw " \
+ "nfsroot=$serverip:$rootpath " \
+ "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off "\
+ "console=$consoledev,$baudrate $othbootargs;" \
+ "tftp $loadaddr $tftppath/$bootfile;" \
+ "tftp $fdtaddr $tftppath/$fdtfile;" \
+ "bootm $loadaddr - $fdtaddr"
+
+
+#define CONFIG_RAMBOOTCOMMAND \
+ "setenv bootargs root=/dev/ram rw " \
+ "console=$consoledev,$baudrate $othbootargs;" \
+ "tftp $ramdiskaddr $tftppath/$ramdiskfile;" \
+ "tftp $loadaddr $tftppath/$bootfile;" \
+ "tftp $fdtaddr $tftppath/$fdtfile;" \
+ "bootm $loadaddr $ramdiskaddr $fdtaddr"
+
+#define CONFIG_BOOTCOMMAND CONFIG_HDBOOT
+
+#endif /* __CONFIG_H */
Code Review / kvmfornfv.git / blobdiff