--- /dev/null
+/*
+ * Copyright 2007, 2010-2011 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+/*
+ * mpc8544ds board configuration file
+ *
+ */
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/* High Level Configuration Options */
+#define CONFIG_BOOKE 1 /* BOOKE */
+#define CONFIG_E500 1 /* BOOKE e500 family */
+#define CONFIG_MPC8544 1
+#define CONFIG_MPC8544DS 1
+
+#ifndef CONFIG_SYS_TEXT_BASE
+#define CONFIG_SYS_TEXT_BASE 0xfff80000
+#endif
+
+#define CONFIG_PCI 1 /* Enable PCI/PCIE */
+#define CONFIG_PCI1 1 /* PCI controller 1 */
+#define CONFIG_PCIE1 1 /* PCIE controler 1 (slot 1) */
+#define CONFIG_PCIE2 1 /* PCIE controler 2 (slot 2) */
+#define CONFIG_PCIE3 1 /* PCIE controler 3 (ULI bridge) */
+#define CONFIG_FSL_PCI_INIT 1 /* Use common FSL init code */
+#define CONFIG_PCI_INDIRECT_BRIDGE 1 /* indirect PCI bridge support */
+#define CONFIG_FSL_PCIE_RESET 1 /* need PCIe reset errata */
+#define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */
+
+#define CONFIG_FSL_LAW 1 /* Use common FSL init code */
+#define CONFIG_E1000 1 /* Defind e1000 pci Ethernet card*/
+
+#define CONFIG_TSEC_ENET /* tsec ethernet support */
+#define CONFIG_ENV_OVERWRITE
+#define CONFIG_INTERRUPTS /* enable pci, srio, ddr interrupts */
+
+#ifndef __ASSEMBLY__
+extern unsigned long get_board_sys_clk(unsigned long dummy);
+#endif
+#define CONFIG_SYS_CLK_FREQ get_board_sys_clk(0) /* sysclk for MPC85xx */
+
+/*
+ * These can be toggled for performance analysis, otherwise use default.
+ */
+#define CONFIG_L2_CACHE /* toggle L2 cache */
+#define CONFIG_BTB /* toggle branch predition */
+
+/*
+ * Only possible on E500 Version 2 or newer cores.
+ */
+#define CONFIG_ENABLE_36BIT_PHYS 1
+
+#define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */
+#define CONFIG_SYS_MEMTEST_END 0x00400000
+#define CONFIG_PANIC_HANG /* do not reset board on panic */
+
+#define CONFIG_SYS_CCSRBAR 0xe0000000
+#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR
+
+/* DDR Setup */
+#define CONFIG_SYS_FSL_DDR2
+#undef CONFIG_FSL_DDR_INTERACTIVE
+#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */
+#define CONFIG_DDR_SPD
+
+#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */
+#define CONFIG_MEM_INIT_VALUE 0xDeadBeef
+
+#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000
+#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
+#define CONFIG_VERY_BIG_RAM
+
+#define CONFIG_NUM_DDR_CONTROLLERS 1
+#define CONFIG_DIMM_SLOTS_PER_CTLR 1
+#define CONFIG_CHIP_SELECTS_PER_CTRL 2
+
+/* I2C addresses of SPD EEPROMs */
+#define SPD_EEPROM_ADDRESS 0x51 /* DDR DIMM */
+
+/* Make sure required options are set */
+#ifndef CONFIG_SPD_EEPROM
+#error ("CONFIG_SPD_EEPROM is required")
+#endif
+
+#undef CONFIG_CLOCKS_IN_MHZ
+
+/*
+ * Memory map
+ *
+ * 0x0000_0000 0x7fff_ffff DDR 2G Cacheable
+ *
+ * 0x8000_0000 0xbfff_ffff PCI Express Mem 1G non-cacheable
+ *
+ * 0xc000_0000 0xdfff_ffff PCI 512M non-cacheable
+ *
+ * 0xe000_0000 0xe00f_ffff CCSR 1M non-cacheable
+ * 0xe100_0000 0xe3ff_ffff PCI IO range 4M non-cacheable
+ *
+ * Localbus cacheable
+ *
+ * 0xf000_0000 0xf3ff_ffff SDRAM 64M Cacheable
+ * 0xf401_0000 0xf401_3fff L1 for stack 4K Cacheable TLB0
+ *
+ * Localbus non-cacheable
+ *
+ * 0xf800_0000 0xf80f_ffff NVRAM/CADMUS (*) 1M non-cacheable
+ * 0xff00_0000 0xff7f_ffff FLASH (2nd bank) 8M non-cacheable
+ * 0xff80_0000 0xffff_ffff FLASH (boot bank) 8M non-cacheable
+ *
+ */
+
+/*
+ * Local Bus Definitions
+ */
+#define CONFIG_SYS_BOOT_BLOCK 0xfc000000 /* boot TLB */
+
+#define CONFIG_SYS_FLASH_BASE 0xff800000 /* start of FLASH 8M */
+
+#define CONFIG_SYS_BR0_PRELIM 0xff801001
+#define CONFIG_SYS_BR1_PRELIM 0xfe801001
+
+#define CONFIG_SYS_OR0_PRELIM 0xff806e65
+#define CONFIG_SYS_OR1_PRELIM 0xff806e65
+
+#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE}
+
+#define CONFIG_SYS_FLASH_QUIET_TEST
+#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */
+#define CONFIG_SYS_MAX_FLASH_SECT 128 /* sectors per device */
+#undef CONFIG_SYS_FLASH_CHECKSUM
+#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
+#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */
+
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
+
+#define CONFIG_FLASH_CFI_DRIVER
+#define CONFIG_SYS_FLASH_CFI
+#define CONFIG_SYS_FLASH_EMPTY_INFO
+
+#define CONFIG_SYS_LBC_NONCACHE_BASE 0xf8000000
+
+#define CONFIG_SYS_BR2_PRELIM 0xf8201001 /* port size 16bit */
+#define CONFIG_SYS_OR2_PRELIM 0xfff06ff7 /* 1MB Compact Flash area*/
+
+#define CONFIG_SYS_BR3_PRELIM 0xf8100801 /* port size 8bit */
+#define CONFIG_SYS_OR3_PRELIM 0xfff06ff7 /* 1MB PIXIS area*/
+
+#define CONFIG_FSL_PIXIS 1 /* use common PIXIS code */
+#define PIXIS_BASE 0xf8100000 /* PIXIS registers */
+#define PIXIS_ID 0x0 /* Board ID at offset 0 */
+#define PIXIS_VER 0x1 /* Board version at offset 1 */
+#define PIXIS_PVER 0x2 /* PIXIS FPGA version at offset 2 */
+#define PIXIS_RST 0x4 /* PIXIS Reset Control register */
+#define PIXIS_AUX 0x6 /* PIXIS Auxiliary register; Scratch
+ * register */
+#define PIXIS_SPD 0x7 /* Register for SYSCLK speed */
+#define PIXIS_VCTL 0x10 /* VELA Control Register */
+#define PIXIS_VCFGEN0 0x12 /* VELA Config Enable 0 */
+#define PIXIS_VCFGEN1 0x13 /* VELA Config Enable 1 */
+#define PIXIS_VBOOT 0x16 /* VELA VBOOT Register */
+#define PIXIS_VBOOT_FMAP 0x80 /* VBOOT - CFG_FLASHMAP */
+#define PIXIS_VBOOT_FBANK 0x40 /* VBOOT - CFG_FLASHBANK */
+#define PIXIS_VSPEED0 0x17 /* VELA VSpeed 0 */
+#define PIXIS_VSPEED1 0x18 /* VELA VSpeed 1 */
+#define PIXIS_VCLKH 0x19 /* VELA VCLKH register */
+#define PIXIS_VCLKL 0x1A /* VELA VCLKL register */
+#define PIXIS_VSPEED2 0x1d /* VELA VSpeed 2 */
+#define CONFIG_SYS_PIXIS_VBOOT_MASK 0x40 /* Reset altbank mask*/
+#define PIXIS_VSPEED2_TSEC1SER 0x2
+#define PIXIS_VSPEED2_TSEC3SER 0x1
+#define PIXIS_VCFGEN1_TSEC1SER 0x20
+#define PIXIS_VCFGEN1_TSEC3SER 0x40
+#define PIXIS_VSPEED2_MASK (PIXIS_VSPEED2_TSEC1SER|PIXIS_VSPEED2_TSEC3SER)
+#define PIXIS_VCFGEN1_MASK (PIXIS_VCFGEN1_TSEC1SER|PIXIS_VCFGEN1_TSEC3SER)
+
+
+#define CONFIG_SYS_INIT_RAM_LOCK 1
+#define CONFIG_SYS_INIT_RAM_ADDR 0xf4010000 /* Initial L1 address */
+#define CONFIG_SYS_INIT_RAM_SIZE 0x00004000 /* Size of used area in RAM */
+
+
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
+
+#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
+#define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserved for malloc */
+
+/* Serial Port - controlled on board with jumper J8
+ * open - index 2
+ * shorted - index 1
+ */
+#define CONFIG_CONS_INDEX 1
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE 1
+#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
+
+#define CONFIG_SYS_BAUDRATE_TABLE \
+ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
+
+#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500)
+#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600)
+
+/* Use the HUSH parser */
+#define CONFIG_SYS_HUSH_PARSER
+
+/* pass open firmware flat tree */
+#define CONFIG_OF_LIBFDT 1
+#define CONFIG_OF_BOARD_SETUP 1
+#define CONFIG_OF_STDOUT_VIA_ALIAS 1
+
+/* I2C */
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_FSL
+#define CONFIG_SYS_FSL_I2C_SPEED 400000
+#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
+#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} }
+#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57
+
+/*
+ * General PCI
+ * Memory space is mapped 1-1, but I/O space must start from 0.
+ */
+#define CONFIG_SYS_PCIE_VIRT 0x80000000 /* 1G PCIE TLB */
+#define CONFIG_SYS_PCIE_PHYS 0x80000000 /* 1G PCIE TLB */
+#define CONFIG_SYS_PCI_VIRT 0xc0000000 /* 512M PCI TLB */
+#define CONFIG_SYS_PCI_PHYS 0xc0000000 /* 512M PCI TLB */
+
+#define CONFIG_SYS_PCI1_MEM_VIRT 0xc0000000
+#define CONFIG_SYS_PCI1_MEM_BUS 0xc0000000
+#define CONFIG_SYS_PCI1_MEM_PHYS 0xc0000000
+#define CONFIG_SYS_PCI1_MEM_SIZE 0x20000000 /* 512M */
+#define CONFIG_SYS_PCI1_IO_VIRT 0xe1000000
+#define CONFIG_SYS_PCI1_IO_BUS 0x00000000
+#define CONFIG_SYS_PCI1_IO_PHYS 0xe1000000
+#define CONFIG_SYS_PCI1_IO_SIZE 0x00010000 /* 64k */
+
+/* controller 2, Slot 1, tgtid 1, Base address 9000 */
+#define CONFIG_SYS_PCIE2_NAME "Slot 1"
+#define CONFIG_SYS_PCIE2_MEM_VIRT 0x80000000
+#define CONFIG_SYS_PCIE2_MEM_BUS 0x80000000
+#define CONFIG_SYS_PCIE2_MEM_PHYS 0x80000000
+#define CONFIG_SYS_PCIE2_MEM_SIZE 0x20000000 /* 512M */
+#define CONFIG_SYS_PCIE2_IO_VIRT 0xe1010000
+#define CONFIG_SYS_PCIE2_IO_BUS 0x00000000
+#define CONFIG_SYS_PCIE2_IO_PHYS 0xe1010000
+#define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */
+
+/* controller 1, Slot 2,tgtid 2, Base address a000 */
+#define CONFIG_SYS_PCIE1_NAME "Slot 2"
+#define CONFIG_SYS_PCIE1_MEM_VIRT 0xa0000000
+#define CONFIG_SYS_PCIE1_MEM_BUS 0xa0000000
+#define CONFIG_SYS_PCIE1_MEM_PHYS 0xa0000000
+#define CONFIG_SYS_PCIE1_MEM_SIZE 0x10000000 /* 256M */
+#define CONFIG_SYS_PCIE1_IO_VIRT 0xe1020000
+#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000
+#define CONFIG_SYS_PCIE1_IO_PHYS 0xe1020000
+#define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */
+
+/* controller 3, direct to uli, tgtid 3, Base address b000 */
+#define CONFIG_SYS_PCIE3_NAME "ULI"
+#define CONFIG_SYS_PCIE3_MEM_VIRT 0xb0000000
+#define CONFIG_SYS_PCIE3_MEM_BUS 0xb0000000
+#define CONFIG_SYS_PCIE3_MEM_PHYS 0xb0000000
+#define CONFIG_SYS_PCIE3_MEM_SIZE 0x00100000 /* 1M */
+#define CONFIG_SYS_PCIE3_IO_VIRT 0xb0100000 /* reuse mem LAW */
+#define CONFIG_SYS_PCIE3_IO_BUS 0x00000000
+#define CONFIG_SYS_PCIE3_IO_PHYS 0xb0100000 /* reuse mem LAW */
+#define CONFIG_SYS_PCIE3_IO_SIZE 0x00100000 /* 1M */
+#define CONFIG_SYS_PCIE3_MEM_VIRT2 0xb0200000
+#define CONFIG_SYS_PCIE3_MEM_BUS2 0xb0200000
+#define CONFIG_SYS_PCIE3_MEM_PHYS2 0xb0200000
+#define CONFIG_SYS_PCIE3_MEM_SIZE2 0x00200000 /* 1M */
+
+#if defined(CONFIG_PCI)
+
+/*PCIE video card used*/
+#define VIDEO_IO_OFFSET CONFIG_SYS_PCIE2_IO_VIRT
+
+/*PCI video card used*/
+/*#define VIDEO_IO_OFFSET CONFIG_SYS_PCI1_IO_VIRT*/
+
+/* video */
+#define CONFIG_VIDEO
+
+#if defined(CONFIG_VIDEO)
+#define CONFIG_BIOSEMU
+#define CONFIG_CFB_CONSOLE
+#define CONFIG_VIDEO_SW_CURSOR
+#define CONFIG_VGA_AS_SINGLE_DEVICE
+#define CONFIG_ATI_RADEON_FB
+#define CONFIG_VIDEO_LOGO
+/*#define CONFIG_CONSOLE_CURSOR*/
+#define CONFIG_SYS_ISA_IO_BASE_ADDRESS VIDEO_IO_OFFSET
+#endif
+
+#define CONFIG_PCI_PNP /* do pci plug-and-play */
+
+#undef CONFIG_EEPRO100
+#undef CONFIG_TULIP
+#define CONFIG_RTL8139
+
+#ifndef CONFIG_PCI_PNP
+ #define PCI_ENET0_IOADDR CONFIG_SYS_PCI1_IO_BUS
+ #define PCI_ENET0_MEMADDR CONFIG_SYS_PCI1_IO_BUS
+ #define PCI_IDSEL_NUMBER 0x11 /* IDSEL = AD11 */
+#endif
+
+#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
+#define CONFIG_DOS_PARTITION
+#define CONFIG_SCSI_AHCI
+
+#ifdef CONFIG_SCSI_AHCI
+#define CONFIG_LIBATA
+#define CONFIG_SATA_ULI5288
+#define CONFIG_SYS_SCSI_MAX_SCSI_ID 4
+#define CONFIG_SYS_SCSI_MAX_LUN 1
+#define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * CONFIG_SYS_SCSI_MAX_LUN)
+#define CONFIG_SYS_SCSI_MAXDEVICE CONFIG_SYS_SCSI_MAX_DEVICE
+#endif /* SCSCI */
+
+#endif /* CONFIG_PCI */
+
+
+#if defined(CONFIG_TSEC_ENET)
+
+#define CONFIG_MII 1 /* MII PHY management */
+#define CONFIG_MII_DEFAULT_TSEC 1 /* Allow unregistered phys */
+#define CONFIG_TSEC1 1
+#define CONFIG_TSEC1_NAME "eTSEC1"
+#define CONFIG_TSEC3 1
+#define CONFIG_TSEC3_NAME "eTSEC3"
+
+#define CONFIG_PIXIS_SGMII_CMD
+#define CONFIG_FSL_SGMII_RISER 1
+#define SGMII_RISER_PHY_OFFSET 0x1c
+
+#define TSEC1_PHY_ADDR 0
+#define TSEC3_PHY_ADDR 1
+
+#define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
+#define TSEC3_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
+
+#define TSEC1_PHYIDX 0
+#define TSEC3_PHYIDX 0
+
+#define CONFIG_ETHPRIME "eTSEC1"
+
+#define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */
+#endif /* CONFIG_TSEC_ENET */
+
+/*
+ * Environment
+ */
+#define CONFIG_ENV_IS_IN_FLASH 1
+#if CONFIG_SYS_MONITOR_BASE > 0xfff80000
+#define CONFIG_ENV_ADDR 0xfff80000
+#else
+#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + 0x70000)
+#endif
+#define CONFIG_ENV_SIZE 0x2000
+#define CONFIG_ENV_SECT_SIZE 0x10000 /* 64K (one sector) */
+
+#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
+#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_IRQ
+#define CONFIG_CMD_SETEXPR
+#define CONFIG_CMD_REGINFO
+
+#if defined(CONFIG_PCI)
+ #define CONFIG_CMD_PCI
+ #define CONFIG_CMD_NET
+ #define CONFIG_CMD_SCSI
+ #define CONFIG_CMD_EXT2
+#endif
+
+/*
+ * USB
+ */
+#define CONFIG_USB_EHCI
+
+#ifdef CONFIG_USB_EHCI
+#define CONFIG_CMD_USB
+#define CONFIG_USB_EHCI_PCI
+#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
+#define CONFIG_USB_STORAGE
+#define CONFIG_PCI_EHCI_DEVICE 0
+#endif
+
+#undef CONFIG_WATCHDOG /* watchdog disabled */
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#define CONFIG_CMDLINE_EDITING /* Command-line editing */
+#define CONFIG_AUTO_COMPLETE /* add autocompletion support */
+#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
+#if defined(CONFIG_CMD_KGDB)
+#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
+#else
+#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
+#endif
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 64 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial Memory map for Linux*/
+#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
+
+#if defined(CONFIG_CMD_KGDB)
+#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
+#endif
+
+/*
+ * Environment Configuration
+ */
+
+/* The mac addresses for all ethernet interface */
+#if defined(CONFIG_TSEC_ENET)
+#define CONFIG_HAS_ETH0
+#define CONFIG_ETHADDR 00:E0:0C:02:00:FD
+#define CONFIG_HAS_ETH1
+#define CONFIG_ETH1ADDR 00:E0:0C:02:01:FD
+#endif
+
+#define CONFIG_IPADDR 192.168.1.251
+
+#define CONFIG_HOSTNAME 8544ds_unknown
+#define CONFIG_ROOTPATH "/nfs/mpc85xx"
+#define CONFIG_BOOTFILE "8544ds/uImage.uboot"
+#define CONFIG_UBOOTPATH 8544ds/u-boot.bin /* TFTP server */
+
+#define CONFIG_SERVERIP 192.168.1.1
+#define CONFIG_GATEWAYIP 192.168.1.1
+#define CONFIG_NETMASK 255.255.0.0
+
+#define CONFIG_LOADADDR 1000000 /*default location for tftp and bootm*/
+
+#define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */
+#undef CONFIG_BOOTARGS /* the boot command will set bootargs*/
+
+#define CONFIG_BAUDRATE 115200
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+"netdev=eth0\0" \
+"uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \
+"tftpflash=tftpboot $loadaddr $uboot; " \
+ "protect off " __stringify(CONFIG_SYS_TEXT_BASE) \
+ " +$filesize; " \
+ "erase " __stringify(CONFIG_SYS_TEXT_BASE) \
+ " +$filesize; " \
+ "cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE) \
+ " $filesize; " \
+ "protect on " __stringify(CONFIG_SYS_TEXT_BASE) \
+ " +$filesize; " \
+ "cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE) \
+ " $filesize\0" \
+"consoledev=ttyS0\0" \
+"ramdiskaddr=2000000\0" \
+"ramdiskfile=8544ds/ramdisk.uboot\0" \
+"fdtaddr=c00000\0" \
+"fdtfile=8544ds/mpc8544ds.dtb\0" \
+"bdev=sda3\0"
+
+#define CONFIG_NFSBOOTCOMMAND \
+ "setenv bootargs root=/dev/nfs rw " \
+ "nfsroot=$serverip:$rootpath " \
+ "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
+ "console=$consoledev,$baudrate $othbootargs;" \
+ "tftp $loadaddr $bootfile;" \
+ "tftp $fdtaddr $fdtfile;" \
+ "bootm $loadaddr - $fdtaddr"
+
+#define CONFIG_RAMBOOTCOMMAND \
+ "setenv bootargs root=/dev/ram rw " \
+ "console=$consoledev,$baudrate $othbootargs;" \
+ "tftp $ramdiskaddr $ramdiskfile;" \
+ "tftp $loadaddr $bootfile;" \
+ "tftp $fdtaddr $fdtfile;" \
+ "bootm $loadaddr $ramdiskaddr $fdtaddr"
+
+#define CONFIG_BOOTCOMMAND \
+ "setenv bootargs root=/dev/$bdev rw " \
+ "console=$consoledev,$baudrate $othbootargs;" \
+ "tftp $loadaddr $bootfile;" \
+ "tftp $fdtaddr $fdtfile;" \
+ "bootm $loadaddr - $fdtaddr"
+
+#endif /* __CONFIG_H */
Code Review / kvmfornfv.git / blobdiff