--- /dev/null
+/*
+ * Copyright (C) 2007 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published
+ * by the Free Software Foundation.
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ */
+#define CONFIG_E300 1 /* E300 family */
+#define CONFIG_QE 1 /* Has QE */
+#define CONFIG_MPC832x 1 /* MPC832x CPU specific */
+
+#define CONFIG_SYS_TEXT_BASE 0xFE000000
+
+#define CONFIG_PCI 1
+
+/*
+ * System Clock Setup
+ */
+#define CONFIG_83XX_CLKIN 66666667 /* in Hz */
+
+#ifndef CONFIG_SYS_CLK_FREQ
+#define CONFIG_SYS_CLK_FREQ CONFIG_83XX_CLKIN
+#endif
+
+/*
+ * Hardware Reset Configuration Word
+ */
+#define CONFIG_SYS_HRCW_LOW (\
+ HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
+ HRCWL_DDR_TO_SCB_CLK_2X1 |\
+ HRCWL_VCO_1X2 |\
+ HRCWL_CSB_TO_CLKIN_2X1 |\
+ HRCWL_CORE_TO_CSB_2_5X1 |\
+ HRCWL_CE_PLL_VCO_DIV_2 |\
+ HRCWL_CE_PLL_DIV_1X1 |\
+ HRCWL_CE_TO_PLL_1X3)
+
+#define CONFIG_SYS_HRCW_HIGH (\
+ HRCWH_PCI_HOST |\
+ HRCWH_PCI1_ARBITER_ENABLE |\
+ HRCWH_CORE_ENABLE |\
+ HRCWH_FROM_0X00000100 |\
+ HRCWH_BOOTSEQ_DISABLE |\
+ HRCWH_SW_WATCHDOG_DISABLE |\
+ HRCWH_ROM_LOC_LOCAL_16BIT |\
+ HRCWH_BIG_ENDIAN |\
+ HRCWH_LALE_NORMAL)
+
+/*
+ * System IO Config
+ */
+#define CONFIG_SYS_SICRL 0x00000000
+
+/*
+ * IMMR new address
+ */
+#define CONFIG_SYS_IMMR 0xE0000000
+
+/*
+ * System performance
+ */
+#define CONFIG_SYS_ACR_PIPE_DEP 3 /* Arbiter pipeline depth (0-3) */
+#define CONFIG_SYS_ACR_RPTCNT 3 /* Arbiter repeat count (0-7) */
+/* (0-1) Optimize transactions between CSB and the SEC and QUICC Engine block */
+#define CONFIG_SYS_SPCR_OPT 1
+
+/*
+ * DDR Setup
+ */
+#define CONFIG_SYS_DDR_BASE 0x00000000 /* DDR is system memory */
+#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE
+#define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE
+
+#undef CONFIG_SPD_EEPROM
+#if defined(CONFIG_SPD_EEPROM)
+/* Determine DDR configuration from I2C interface
+ */
+#define SPD_EEPROM_ADDRESS 0x51 /* DDR SODIMM */
+#else
+/* Manually set up DDR parameters
+ */
+#define CONFIG_SYS_DDR_SIZE 64 /* MB */
+#define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN \
+ | CSCONFIG_ROW_BIT_13 \
+ | CSCONFIG_COL_BIT_9)
+ /* 0x80010101 */
+#define CONFIG_SYS_DDR_TIMING_0 ((0 << TIMING_CFG0_RWT_SHIFT) \
+ | (0 << TIMING_CFG0_WRT_SHIFT) \
+ | (0 << TIMING_CFG0_RRT_SHIFT) \
+ | (0 << TIMING_CFG0_WWT_SHIFT) \
+ | (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) \
+ | (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) \
+ | (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) \
+ | (2 << TIMING_CFG0_MRS_CYC_SHIFT))
+ /* 0x00220802 */
+#define CONFIG_SYS_DDR_TIMING_1 ((2 << TIMING_CFG1_PRETOACT_SHIFT) \
+ | (6 << TIMING_CFG1_ACTTOPRE_SHIFT) \
+ | (2 << TIMING_CFG1_ACTTORW_SHIFT) \
+ | (5 << TIMING_CFG1_CASLAT_SHIFT) \
+ | (3 << TIMING_CFG1_REFREC_SHIFT) \
+ | (2 << TIMING_CFG1_WRREC_SHIFT) \
+ | (2 << TIMING_CFG1_ACTTOACT_SHIFT) \
+ | (2 << TIMING_CFG1_WRTORD_SHIFT))
+ /* 0x26253222 */
+#define CONFIG_SYS_DDR_TIMING_2 ((1 << TIMING_CFG2_ADD_LAT_SHIFT) \
+ | (31 << TIMING_CFG2_CPO_SHIFT) \
+ | (2 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) \
+ | (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) \
+ | (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) \
+ | (3 << TIMING_CFG2_CKE_PLS_SHIFT) \
+ | (7 << TIMING_CFG2_FOUR_ACT_SHIFT))
+ /* 0x1f9048c7 */
+#define CONFIG_SYS_DDR_TIMING_3 0x00000000
+#define CONFIG_SYS_DDR_CLK_CNTL DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05
+ /* 0x02000000 */
+#define CONFIG_SYS_DDR_MODE ((0x4448 << SDRAM_MODE_ESD_SHIFT) \
+ | (0x0232 << SDRAM_MODE_SD_SHIFT))
+ /* 0x44480232 */
+#define CONFIG_SYS_DDR_MODE2 0x8000c000
+#define CONFIG_SYS_DDR_INTERVAL ((800 << SDRAM_INTERVAL_REFINT_SHIFT) \
+ | (100 << SDRAM_INTERVAL_BSTOPRE_SHIFT))
+ /* 0x03200064 */
+#define CONFIG_SYS_DDR_CS0_BNDS 0x00000003
+#define CONFIG_SYS_DDR_SDRAM_CFG (SDRAM_CFG_SREN \
+ | SDRAM_CFG_SDRAM_TYPE_DDR2 \
+ | SDRAM_CFG_32_BE)
+ /* 0x43080000 */
+#define CONFIG_SYS_DDR_SDRAM_CFG2 0x00401000
+#endif
+
+/*
+ * Memory test
+ */
+#undef CONFIG_SYS_DRAM_TEST /* memory test, takes time */
+#define CONFIG_SYS_MEMTEST_START 0x00030000 /* memtest region */
+#define CONFIG_SYS_MEMTEST_END 0x03f00000
+
+/*
+ * The reserved memory
+ */
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
+
+#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
+#define CONFIG_SYS_RAMBOOT
+#else
+#undef CONFIG_SYS_RAMBOOT
+#endif
+
+/* CONFIG_SYS_MONITOR_LEN must be a multiple of CONFIG_ENV_SECT_SIZE */
+#define CONFIG_SYS_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Mon */
+#define CONFIG_SYS_MALLOC_LEN (256 * 1024) /* Reserved for malloc */
+
+/*
+ * Initial RAM Base Address Setup
+ */
+#define CONFIG_SYS_INIT_RAM_LOCK 1
+#define CONFIG_SYS_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */
+#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in RAM */
+#define CONFIG_SYS_GBL_DATA_OFFSET \
+ (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+
+/*
+ * Local Bus Configuration & Clock Setup
+ */
+#define CONFIG_SYS_LCRR_DBYP LCRR_DBYP
+#define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_2
+#define CONFIG_SYS_LBC_LBCR 0x00000000
+
+/*
+ * FLASH on the Local Bus
+ */
+#define CONFIG_SYS_FLASH_CFI /* use the Common Flash Interface */
+#define CONFIG_FLASH_CFI_DRIVER /* use the CFI driver */
+#define CONFIG_SYS_FLASH_BASE 0xFE000000 /* FLASH base address */
+#define CONFIG_SYS_FLASH_SIZE 16 /* FLASH size is 16M */
+#define CONFIG_SYS_FLASH_PROTECTION 1 /* Use h/w Flash protection. */
+
+ /* Window base at flash base */
+#define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE
+#define CONFIG_SYS_LBLAWAR0_PRELIM (LBLAWAR_EN | LBLAWAR_32MB)
+
+#define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE \
+ | BR_PS_16 /* 16 bit port */ \
+ | BR_MS_GPCM /* MSEL = GPCM */ \
+ | BR_V) /* valid */
+#define CONFIG_SYS_OR0_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \
+ | OR_GPCM_XAM \
+ | OR_GPCM_CSNT \
+ | OR_GPCM_ACS_DIV2 \
+ | OR_GPCM_XACS \
+ | OR_GPCM_SCY_15 \
+ | OR_GPCM_TRLX_SET \
+ | OR_GPCM_EHTR_SET \
+ | OR_GPCM_EAD)
+ /* 0xFE006FF7 */
+
+#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */
+#define CONFIG_SYS_MAX_FLASH_SECT 128 /* sectors per device */
+
+#undef CONFIG_SYS_FLASH_CHECKSUM
+
+/*
+ * Serial Port
+ */
+#define CONFIG_CONS_INDEX 1
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE 1
+#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
+
+#define CONFIG_SYS_BAUDRATE_TABLE \
+ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
+
+#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500)
+#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600)
+
+#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
+#define CONFIG_AUTO_COMPLETE /* add autocompletion support */
+/* Use the HUSH parser */
+#define CONFIG_SYS_HUSH_PARSER
+
+/* pass open firmware flat tree */
+#define CONFIG_OF_LIBFDT 1
+#define CONFIG_OF_BOARD_SETUP 1
+#define CONFIG_OF_STDOUT_VIA_ALIAS 1
+
+/* I2C */
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_FSL
+#define CONFIG_SYS_FSL_I2C_SPEED 400000
+#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
+#define CONFIG_SYS_I2C_NOPROBES { {0, 0x51} }
+
+/*
+ * Config on-board EEPROM
+ */
+#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10
+
+/*
+ * General PCI
+ * Addresses are mapped 1-1.
+ */
+#define CONFIG_SYS_PCI1_MEM_BASE 0x80000000
+#define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BASE
+#define CONFIG_SYS_PCI1_MEM_SIZE 0x10000000 /* 256M */
+#define CONFIG_SYS_PCI1_MMIO_BASE 0x90000000
+#define CONFIG_SYS_PCI1_MMIO_PHYS CONFIG_SYS_PCI1_MMIO_BASE
+#define CONFIG_SYS_PCI1_MMIO_SIZE 0x10000000 /* 256M */
+#define CONFIG_SYS_PCI1_IO_BASE 0xd0000000
+#define CONFIG_SYS_PCI1_IO_PHYS CONFIG_SYS_PCI1_IO_BASE
+#define CONFIG_SYS_PCI1_IO_SIZE 0x04000000 /* 64M */
+
+#ifdef CONFIG_PCI
+#define CONFIG_PCI_INDIRECT_BRIDGE
+#define CONFIG_PCI_SKIP_HOST_BRIDGE
+#define CONFIG_PCI_PNP /* do pci plug-and-play */
+
+#undef CONFIG_EEPRO100
+#undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
+#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */
+
+#endif /* CONFIG_PCI */
+
+/*
+ * QE UEC ethernet configuration
+ */
+#define CONFIG_UEC_ETH
+#define CONFIG_ETHPRIME "UEC0"
+
+#define CONFIG_UEC_ETH1 /* ETH3 */
+
+#ifdef CONFIG_UEC_ETH1
+#define CONFIG_SYS_UEC1_UCC_NUM 2 /* UCC3 */
+#define CONFIG_SYS_UEC1_RX_CLK QE_CLK9
+#define CONFIG_SYS_UEC1_TX_CLK QE_CLK10
+#define CONFIG_SYS_UEC1_ETH_TYPE FAST_ETH
+#define CONFIG_SYS_UEC1_PHY_ADDR 4
+#define CONFIG_SYS_UEC1_INTERFACE_TYPE PHY_INTERFACE_MODE_MII
+#define CONFIG_SYS_UEC1_INTERFACE_SPEED 100
+#endif
+
+#define CONFIG_UEC_ETH2 /* ETH4 */
+
+#ifdef CONFIG_UEC_ETH2
+#define CONFIG_SYS_UEC2_UCC_NUM 1 /* UCC2 */
+#define CONFIG_SYS_UEC2_RX_CLK QE_CLK16
+#define CONFIG_SYS_UEC2_TX_CLK QE_CLK3
+#define CONFIG_SYS_UEC2_ETH_TYPE FAST_ETH
+#define CONFIG_SYS_UEC2_PHY_ADDR 0
+#define CONFIG_SYS_UEC2_INTERFACE_TYPE PHY_INTERFACE_MODE_MII
+#define CONFIG_SYS_UEC2_INTERFACE_SPEED 100
+#endif
+
+/*
+ * Environment
+ */
+#ifndef CONFIG_SYS_RAMBOOT
+ #define CONFIG_ENV_IS_IN_FLASH 1
+ #define CONFIG_ENV_ADDR \
+ (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
+ #define CONFIG_ENV_SECT_SIZE 0x20000
+ #define CONFIG_ENV_SIZE 0x2000
+#else
+ #define CONFIG_SYS_NO_FLASH 1 /* Flash is not usable now */
+ #define CONFIG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */
+ #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000)
+ #define CONFIG_ENV_SIZE 0x2000
+#endif
+
+#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
+#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_EEPROM
+#define CONFIG_CMD_ASKENV
+
+#if defined(CONFIG_PCI)
+ #define CONFIG_CMD_PCI
+#endif
+#if defined(CONFIG_SYS_RAMBOOT)
+ #undef CONFIG_CMD_SAVEENV
+ #undef CONFIG_CMD_LOADS
+#endif
+
+#undef CONFIG_WATCHDOG /* watchdog disabled */
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
+
+#if (CONFIG_CMD_KGDB)
+ #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
+#else
+ #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
+#endif
+
+ /* Print Buffer Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+ /* Boot Argument Buffer Size */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 256 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+ /* Initial Memory map for Linux */
+#define CONFIG_SYS_BOOTMAPSZ (256 << 20)
+
+/*
+ * Core HID Setup
+ */
+#define CONFIG_SYS_HID0_INIT 0x000000000
+#define CONFIG_SYS_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK | \
+ HID0_ENABLE_INSTRUCTION_CACHE)
+#define CONFIG_SYS_HID2 HID2_HBE
+
+/*
+ * MMU Setup
+ */
+#define CONFIG_HIGH_BATS 1 /* High BATs supported */
+
+/* DDR: cache cacheable */
+#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE \
+ | BATL_PP_RW \
+ | BATL_MEMCOHERENCE)
+#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE \
+ | BATU_BL_256M \
+ | BATU_VS \
+ | BATU_VP)
+#define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L
+#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U
+
+/* IMMRBAR & PCI IO: cache-inhibit and guarded */
+#define CONFIG_SYS_IBAT1L (CONFIG_SYS_IMMR \
+ | BATL_PP_RW \
+ | BATL_CACHEINHIBIT \
+ | BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_IBAT1U (CONFIG_SYS_IMMR \
+ | BATU_BL_4M \
+ | BATU_VS \
+ | BATU_VP)
+#define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L
+#define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U
+
+/* FLASH: icache cacheable, but dcache-inhibit and guarded */
+#define CONFIG_SYS_IBAT2L (CONFIG_SYS_FLASH_BASE \
+ | BATL_PP_RW \
+ | BATL_MEMCOHERENCE)
+#define CONFIG_SYS_IBAT2U (CONFIG_SYS_FLASH_BASE \
+ | BATU_BL_32M \
+ | BATU_VS \
+ | BATU_VP)
+#define CONFIG_SYS_DBAT2L (CONFIG_SYS_FLASH_BASE \
+ | BATL_PP_RW \
+ | BATL_CACHEINHIBIT \
+ | BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U
+
+#define CONFIG_SYS_IBAT3L (0)
+#define CONFIG_SYS_IBAT3U (0)
+#define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L
+#define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U
+
+/* Stack in dcache: cacheable, no memory coherence */
+#define CONFIG_SYS_IBAT4L (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_RW)
+#define CONFIG_SYS_IBAT4U (CONFIG_SYS_INIT_RAM_ADDR \
+ | BATU_BL_128K \
+ | BATU_VS \
+ | BATU_VP)
+#define CONFIG_SYS_DBAT4L CONFIG_SYS_IBAT4L
+#define CONFIG_SYS_DBAT4U CONFIG_SYS_IBAT4U
+
+#ifdef CONFIG_PCI
+/* PCI MEM space: cacheable */
+#define CONFIG_SYS_IBAT5L (CONFIG_SYS_PCI1_MEM_PHYS \
+ | BATL_PP_RW \
+ | BATL_MEMCOHERENCE)
+#define CONFIG_SYS_IBAT5U (CONFIG_SYS_PCI1_MEM_PHYS \
+ | BATU_BL_256M \
+ | BATU_VS \
+ | BATU_VP)
+#define CONFIG_SYS_DBAT5L CONFIG_SYS_IBAT5L
+#define CONFIG_SYS_DBAT5U CONFIG_SYS_IBAT5U
+/* PCI MMIO space: cache-inhibit and guarded */
+#define CONFIG_SYS_IBAT6L (CONFIG_SYS_PCI1_MMIO_PHYS \
+ | BATL_PP_RW \
+ | BATL_CACHEINHIBIT \
+ | BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_IBAT6U (CONFIG_SYS_PCI1_MMIO_PHYS \
+ | BATU_BL_256M \
+ | BATU_VS \
+ | BATU_VP)
+#define CONFIG_SYS_DBAT6L CONFIG_SYS_IBAT6L
+#define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U
+#else
+#define CONFIG_SYS_IBAT5L (0)
+#define CONFIG_SYS_IBAT5U (0)
+#define CONFIG_SYS_IBAT6L (0)
+#define CONFIG_SYS_IBAT6U (0)
+#define CONFIG_SYS_DBAT5L CONFIG_SYS_IBAT5L
+#define CONFIG_SYS_DBAT5U CONFIG_SYS_IBAT5U
+#define CONFIG_SYS_DBAT6L CONFIG_SYS_IBAT6L
+#define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U
+#endif
+
+/* Nothing in BAT7 */
+#define CONFIG_SYS_IBAT7L (0)
+#define CONFIG_SYS_IBAT7U (0)
+#define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L
+#define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U
+
+#if (CONFIG_CMD_KGDB)
+#define CONFIG_KGDB_BAUDRATE 230400 /* speed of kgdb serial port */
+#endif
+
+/*
+ * Environment Configuration
+ */
+#define CONFIG_ENV_OVERWRITE
+
+#define CONFIG_HAS_ETH0 /* add support for "ethaddr" */
+#define CONFIG_HAS_ETH1 /* add support for "eth1addr" */
+
+/* use mac_read_from_eeprom() to read ethaddr from I2C EEPROM
+ * (see CONFIG_SYS_I2C_EEPROM) */
+ /* MAC address offset in I2C EEPROM */
+#define CONFIG_SYS_I2C_MAC_OFFSET 0x7f00
+
+#define CONFIG_NETDEV "eth1"
+
+#define CONFIG_HOSTNAME mpc8323erdb
+#define CONFIG_ROOTPATH "/nfsroot"
+#define CONFIG_BOOTFILE "uImage"
+ /* U-Boot image on TFTP server */
+#define CONFIG_UBOOTPATH "u-boot.bin"
+#define CONFIG_FDTFILE "mpc832x_rdb.dtb"
+#define CONFIG_RAMDISKFILE "rootfs.ext2.gz.uboot"
+
+ /* default location for tftp and bootm */
+#define CONFIG_LOADADDR 800000
+#define CONFIG_BOOTDELAY 6 /* -1 disables auto-boot */
+#define CONFIG_BAUDRATE 115200
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "netdev=" CONFIG_NETDEV "\0" \
+ "uboot=" CONFIG_UBOOTPATH "\0" \
+ "tftpflash=tftp $loadaddr $uboot;" \
+ "protect off " __stringify(CONFIG_SYS_TEXT_BASE) \
+ " +$filesize; " \
+ "erase " __stringify(CONFIG_SYS_TEXT_BASE) \
+ " +$filesize; " \
+ "cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE) \
+ " $filesize; " \
+ "protect on " __stringify(CONFIG_SYS_TEXT_BASE) \
+ " +$filesize; " \
+ "cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE) \
+ " $filesize\0" \
+ "fdtaddr=780000\0" \
+ "fdtfile=" CONFIG_FDTFILE "\0" \
+ "ramdiskaddr=1000000\0" \
+ "ramdiskfile=" CONFIG_RAMDISKFILE "\0" \
+ "console=ttyS0\0" \
+ "setbootargs=setenv bootargs " \
+ "root=$rootdev rw console=$console,$baudrate $othbootargs\0"\
+ "setipargs=setenv bootargs nfsroot=$serverip:$rootpath " \
+ "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:"\
+ "$netdev:off "\
+ "root=$rootdev rw console=$console,$baudrate $othbootargs\0"
+
+#define CONFIG_NFSBOOTCOMMAND \
+ "setenv rootdev /dev/nfs;" \
+ "run setbootargs;" \
+ "run setipargs;" \
+ "tftp $loadaddr $bootfile;" \
+ "tftp $fdtaddr $fdtfile;" \
+ "bootm $loadaddr - $fdtaddr"
+
+#define CONFIG_RAMBOOTCOMMAND \
+ "setenv rootdev /dev/ram;" \
+ "run setbootargs;" \
+ "tftp $ramdiskaddr $ramdiskfile;" \
+ "tftp $loadaddr $bootfile;" \
+ "tftp $fdtaddr $fdtfile;" \
+ "bootm $loadaddr $ramdiskaddr $fdtaddr"
+
+#endif /* __CONFIG_H */
Code Review / kvmfornfv.git / blobdiff