--- /dev/null
+/*
+ * Configuation settings for the Motorola MC5275EVB board.
+ *
+ * By Arthur Shipkowski <art@videon-central.com>
+ * Copyright (C) 2005 Videon Central, Inc.
+ *
+ * Based off of M5272C3 board code by Josef Baumgartner
+ * <josef.baumgartner@telex.de>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+/*
+ * board/config.h - configuration options, board specific
+ */
+
+#ifndef _M5275EVB_H
+#define _M5275EVB_H
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+#define CONFIG_MCF52x2 /* define processor family */
+#define CONFIG_M5275 /* define processor type */
+#define CONFIG_M5275EVB /* define board type */
+
+#define CONFIG_MCFTMR
+
+#define CONFIG_MCFUART
+#define CONFIG_SYS_UART_PORT (0)
+#define CONFIG_BAUDRATE 115200
+
+/* Configuration for environment
+ * Environment is embedded in u-boot in the second sector of the flash
+ */
+#ifndef CONFIG_MONITOR_IS_IN_RAM
+#define CONFIG_ENV_OFFSET 0x4000
+#define CONFIG_ENV_SECT_SIZE 0x2000
+#define CONFIG_ENV_IS_IN_FLASH 1
+#else
+#define CONFIG_ENV_ADDR 0xffe04000
+#define CONFIG_ENV_SECT_SIZE 0x2000
+#define CONFIG_ENV_IS_IN_FLASH 1
+#endif
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+/* Available command configuration */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_CACHE
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_FLASH
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_MEMORY
+#define CONFIG_CMD_DHCP
+
+#undef CONFIG_CMD_LOADS
+#undef CONFIG_CMD_LOADB
+
+#define CONFIG_MCFFEC
+#ifdef CONFIG_MCFFEC
+#define CONFIG_MII 1
+#define CONFIG_MII_INIT 1
+#define CONFIG_SYS_DISCOVER_PHY
+#define CONFIG_SYS_RX_ETH_BUFFER 8
+#define CONFIG_SYS_FAULT_ECHO_LINK_DOWN
+#define CONFIG_SYS_FEC0_PINMUX 0
+#define CONFIG_SYS_FEC0_MIIBASE CONFIG_SYS_FEC0_IOBASE
+#define CONFIG_SYS_FEC1_PINMUX 0
+#define CONFIG_SYS_FEC1_MIIBASE CONFIG_SYS_FEC1_IOBASE
+#define MCFFEC_TOUT_LOOP 50000
+#define CONFIG_HAS_ETH1
+/* If CONFIG_SYS_DISCOVER_PHY is not defined - hardcoded */
+#ifndef CONFIG_SYS_DISCOVER_PHY
+#define FECDUPLEX FULL
+#define FECSPEED _100BASET
+#else
+#ifndef CONFIG_SYS_FAULT_ECHO_LINK_DOWN
+#define CONFIG_SYS_FAULT_ECHO_LINK_DOWN
+#endif
+#endif
+#endif
+
+/* I2C */
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_FSL
+#define CONFIG_SYS_FSL_I2C_SPEED 80000
+#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C_OFFSET 0x00000300
+#define CONFIG_SYS_IMMR CONFIG_SYS_MBAR
+#define CONFIG_SYS_I2C_PINMUX_REG (gpio_reg->par_feci2c)
+#define CONFIG_SYS_I2C_PINMUX_CLR (0xFFF0)
+#define CONFIG_SYS_I2C_PINMUX_SET (0x000F)
+
+#define CONFIG_SYS_PROMPT "-> "
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+
+#if (CONFIG_CMD_KGDB)
+# define CONFIG_SYS_CBSIZE 1024
+#else
+# define CONFIG_SYS_CBSIZE 256
+#endif
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
+#define CONFIG_SYS_MAXARGS 16
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
+
+#define CONFIG_SYS_LOAD_ADDR 0x800000
+
+#define CONFIG_BOOTDELAY 5
+#define CONFIG_BOOTCOMMAND "bootm ffe40000"
+#define CONFIG_SYS_MEMTEST_START 0x400
+#define CONFIG_SYS_MEMTEST_END 0x380000
+
+#ifdef CONFIG_MCFFEC
+# define CONFIG_NET_RETRY_COUNT 5
+# define CONFIG_OVERWRITE_ETHADDR_ONCE
+#endif /* FEC_ENET */
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "netdev=eth0\0" \
+ "loadaddr=10000\0" \
+ "uboot=u-boot.bin\0" \
+ "load=tftp ${loadaddr} ${uboot}\0" \
+ "upd=run load; run prog\0" \
+ "prog=prot off ffe00000 ffe3ffff;" \
+ "era ffe00000 ffe3ffff;" \
+ "cp.b ${loadaddr} ffe00000 ${filesize};"\
+ "save\0" \
+ ""
+
+#define CONFIG_SYS_CLK 150000000
+
+/*
+ * Low Level Configuration Settings
+ * (address mappings, register initial values, etc.)
+ * You should know what you are doing if you make changes here.
+ */
+
+#define CONFIG_SYS_MBAR 0x40000000
+
+/*-----------------------------------------------------------------------
+ * Definitions for initial stack pointer and data area (in DPRAM)
+ */
+#define CONFIG_SYS_INIT_RAM_ADDR 0x20000000
+#define CONFIG_SYS_INIT_RAM_SIZE 0x10000 /* Size of used area in internal SRAM */
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
+
+/*-----------------------------------------------------------------------
+ * Start addresses for the final memory configuration
+ * (Set up by the startup code)
+ * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
+ */
+#define CONFIG_SYS_SDRAM_BASE 0x00000000
+#define CONFIG_SYS_SDRAM_SIZE 16 /* SDRAM size in MB */
+#define CONFIG_SYS_FLASH_BASE CONFIG_SYS_CS0_BASE
+
+#ifdef CONFIG_MONITOR_IS_IN_RAM
+#define CONFIG_SYS_MONITOR_BASE 0x20000
+#else
+#define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_FLASH_BASE + 0x400)
+#endif
+
+#define CONFIG_SYS_MONITOR_LEN 0x20000
+#define CONFIG_SYS_MALLOC_LEN (256 << 10)
+#define CONFIG_SYS_BOOTPARAMS_LEN 64*1024
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization ??
+ */
+#define CONFIG_SYS_BOOTMAPSZ (CONFIG_SYS_SDRAM_BASE + (CONFIG_SYS_SDRAM_SIZE << 20))
+#define CONFIG_SYS_BOOTM_LEN (CONFIG_SYS_SDRAM_SIZE << 20)
+
+/*-----------------------------------------------------------------------
+ * FLASH organization
+ */
+#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
+#define CONFIG_SYS_MAX_FLASH_SECT 11 /* max number of sectors on one chip */
+#define CONFIG_SYS_FLASH_ERASE_TOUT 1000
+
+#define CONFIG_SYS_FLASH_CFI 1
+#define CONFIG_FLASH_CFI_DRIVER 1
+#define CONFIG_SYS_FLASH_SIZE 0x200000
+
+/*-----------------------------------------------------------------------
+ * Cache Configuration
+ */
+#define CONFIG_SYS_CACHELINE_SIZE 16
+
+#define ICACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \
+ CONFIG_SYS_INIT_RAM_SIZE - 8)
+#define DCACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \
+ CONFIG_SYS_INIT_RAM_SIZE - 4)
+#define CONFIG_SYS_ICACHE_INV (CF_CACR_CINV | CF_CACR_INVI)
+#define CONFIG_SYS_CACHE_ACR0 (CONFIG_SYS_SDRAM_BASE | \
+ CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) | \
+ CF_ACR_EN | CF_ACR_SM_ALL)
+#define CONFIG_SYS_CACHE_ICACR (CF_CACR_CENB | CF_CACR_CINV | \
+ CF_CACR_DISD | CF_CACR_INVI | \
+ CF_CACR_CEIB | CF_CACR_DCM | \
+ CF_CACR_EUSP)
+
+/*-----------------------------------------------------------------------
+ * Memory bank definitions
+ */
+#define CONFIG_SYS_CS0_BASE 0xffe00000
+#define CONFIG_SYS_CS0_CTRL 0x00001980
+#define CONFIG_SYS_CS0_MASK 0x001F0001
+
+#define CONFIG_SYS_CS1_BASE 0x30000000
+#define CONFIG_SYS_CS1_CTRL 0x00001900
+#define CONFIG_SYS_CS1_MASK 0x00070001
+
+/*-----------------------------------------------------------------------
+ * Port configuration
+ */
+#define CONFIG_SYS_FECI2C 0x0FA0
+
+#endif /* _M5275EVB_H */
Code Review / kvmfornfv.git / blobdiff