--- /dev/null
+/*
+ * Configuation settings for the Freescale MCF5329 FireEngine board.
+ *
+ * Copyright (C) 2004-2007 Freescale Semiconductor, Inc.
+ * TsiChung Liew (Tsi-Chung.Liew@freescale.com)
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+/*
+ * board/config.h - configuration options, board specific
+ */
+
+#ifndef _M5235EVB_H
+#define _M5235EVB_H
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+#define CONFIG_MCF523x /* define processor family */
+#define CONFIG_M5235 /* define processor type */
+
+#define CONFIG_MCFUART
+#define CONFIG_SYS_UART_PORT (0)
+#define CONFIG_BAUDRATE 115200
+
+#undef CONFIG_WATCHDOG
+#define CONFIG_WATCHDOG_TIMEOUT 5000 /* timeout in milliseconds, max timeout is 6.71sec */
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+/* Command line configuration */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_BOOTD
+#define CONFIG_CMD_CACHE
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_FLASH
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_MEMORY
+#define CONFIG_CMD_MISC
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_PCI
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_REGINFO
+
+#undef CONFIG_CMD_LOADB
+#undef CONFIG_CMD_LOADS
+
+#define CONFIG_MCFFEC
+#ifdef CONFIG_MCFFEC
+# define CONFIG_MII 1
+# define CONFIG_MII_INIT 1
+# define CONFIG_SYS_DISCOVER_PHY
+# define CONFIG_SYS_RX_ETH_BUFFER 8
+# define CONFIG_SYS_FAULT_ECHO_LINK_DOWN
+
+# define CONFIG_SYS_FEC0_PINMUX 0
+# define CONFIG_SYS_FEC0_MIIBASE CONFIG_SYS_FEC0_IOBASE
+# define MCFFEC_TOUT_LOOP 50000
+/* If CONFIG_SYS_DISCOVER_PHY is not defined - hardcoded */
+# ifndef CONFIG_SYS_DISCOVER_PHY
+# define FECDUPLEX FULL
+# define FECSPEED _100BASET
+# else
+# ifndef CONFIG_SYS_FAULT_ECHO_LINK_DOWN
+# define CONFIG_SYS_FAULT_ECHO_LINK_DOWN
+# endif
+# endif /* CONFIG_SYS_DISCOVER_PHY */
+#endif
+
+/* Timer */
+#define CONFIG_MCFTMR
+#undef CONFIG_MCFPIT
+
+/* I2C */
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_i2C_FSL
+#define CONFIG_SYS_FSL_I2C_SPEED 80000
+#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C_OFFSET 0x00000300
+#define CONFIG_SYS_IMMR CONFIG_SYS_MBAR
+#define CONFIG_SYS_I2C_PINMUX_REG (gpio->par_qspi)
+#define CONFIG_SYS_I2C_PINMUX_CLR ~(GPIO_PAR_FECI2C_SCL_MASK | GPIO_PAR_FECI2C_SDA_MASK)
+#define CONFIG_SYS_I2C_PINMUX_SET (GPIO_PAR_FECI2C_SCL_I2CSCL | GPIO_PAR_FECI2C_SDA_I2CSDA)
+
+/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
+#define CONFIG_BOOTDELAY 1 /* autoboot after 5 seconds */
+#define CONFIG_BOOTFILE "u-boot.bin"
+#ifdef CONFIG_MCFFEC
+# define CONFIG_ETHADDR 00:e0:0c:bc:e5:60
+# define CONFIG_IPADDR 192.162.1.2
+# define CONFIG_NETMASK 255.255.255.0
+# define CONFIG_SERVERIP 192.162.1.1
+# define CONFIG_GATEWAYIP 192.162.1.1
+# define CONFIG_OVERWRITE_ETHADDR_ONCE
+#endif /* FEC_ENET */
+
+#define CONFIG_HOSTNAME M5235EVB
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "netdev=eth0\0" \
+ "loadaddr=10000\0" \
+ "u-boot=u-boot.bin\0" \
+ "load=tftp ${loadaddr) ${u-boot}\0" \
+ "upd=run load; run prog\0" \
+ "prog=prot off ffe00000 ffe3ffff;" \
+ "era ffe00000 ffe3ffff;" \
+ "cp.b ${loadaddr} ffe00000 ${filesize};"\
+ "save\0" \
+ ""
+
+#define CONFIG_PRAM 512 /* 512 KB */
+#define CONFIG_SYS_PROMPT "-> "
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+
+#if defined(CONFIG_KGDB)
+# define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
+#else
+# define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
+#endif
+
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
+#define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_SDRAM_BASE+0x20000)
+
+#define CONFIG_SYS_CLK 75000000
+#define CONFIG_SYS_CPU_CLK CONFIG_SYS_CLK * 2
+
+#define CONFIG_SYS_MBAR 0x40000000
+
+/*
+ * Low Level Configuration Settings
+ * (address mappings, register initial values, etc.)
+ * You should know what you are doing if you make changes here.
+ */
+/*-----------------------------------------------------------------------
+ * Definitions for initial stack pointer and data area (in DPRAM)
+ */
+#define CONFIG_SYS_INIT_RAM_ADDR 0x20000000
+#define CONFIG_SYS_INIT_RAM_SIZE 0x10000 /* Size of used area in internal SRAM */
+#define CONFIG_SYS_INIT_RAM_CTRL 0x21
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE - 0x10)
+#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
+
+/*-----------------------------------------------------------------------
+ * Start addresses for the final memory configuration
+ * (Set up by the startup code)
+ * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
+ */
+#define CONFIG_SYS_SDRAM_BASE 0x00000000
+#define CONFIG_SYS_SDRAM_SIZE 16 /* SDRAM size in MB */
+
+#define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE + 0x400
+#define CONFIG_SYS_MEMTEST_END ((CONFIG_SYS_SDRAM_SIZE - 3) << 20)
+
+#define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_FLASH_BASE + 0x400)
+#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
+
+#define CONFIG_SYS_BOOTPARAMS_LEN 64*1024
+#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization ??
+ */
+/* Initial Memory map for Linux */
+#define CONFIG_SYS_BOOTMAPSZ (CONFIG_SYS_SDRAM_BASE + (CONFIG_SYS_SDRAM_SIZE << 20))
+#define CONFIG_SYS_BOOTM_LEN (CONFIG_SYS_SDRAM_SIZE << 20)
+
+/*-----------------------------------------------------------------------
+ * FLASH organization
+ */
+#define CONFIG_SYS_FLASH_CFI
+#ifdef CONFIG_SYS_FLASH_CFI
+# define CONFIG_FLASH_CFI_DRIVER 1
+# define CONFIG_SYS_FLASH_SIZE 0x800000 /* Max size that the board might have */
+#ifdef NORFLASH_PS32BIT
+# define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_32BIT
+#else
+# define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT
+#endif
+# define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
+# define CONFIG_SYS_MAX_FLASH_SECT 137 /* max number of sectors on one chip */
+# define CONFIG_SYS_FLASH_PROTECTION /* "Real" (hardware) sectors protection */
+#endif
+
+#define CONFIG_SYS_FLASH_BASE (CONFIG_SYS_CS0_BASE)
+
+/* Configuration for environment
+ * Environment is embedded in u-boot in the second sector of the flash
+ */
+#define CONFIG_ENV_IS_IN_FLASH 1
+#ifdef NORFLASH_PS32BIT
+# define CONFIG_ENV_OFFSET (0x8000)
+# define CONFIG_ENV_SIZE 0x4000
+# define CONFIG_ENV_SECT_SIZE 0x4000
+#else
+# define CONFIG_ENV_OFFSET (0x4000)
+# define CONFIG_ENV_SIZE 0x2000
+# define CONFIG_ENV_SECT_SIZE 0x2000
+#endif
+
+/*-----------------------------------------------------------------------
+ * Cache Configuration
+ */
+#define CONFIG_SYS_CACHELINE_SIZE 16
+
+#define ICACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \
+ CONFIG_SYS_INIT_RAM_SIZE - 8)
+#define DCACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \
+ CONFIG_SYS_INIT_RAM_SIZE - 4)
+#define CONFIG_SYS_ICACHE_INV (CF_CACR_CINV)
+#define CONFIG_SYS_CACHE_ACR0 (CONFIG_SYS_SDRAM_BASE | \
+ CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) | \
+ CF_ACR_EN | CF_ACR_SM_ALL)
+#define CONFIG_SYS_CACHE_ICACR (CF_CACR_CENB | CF_CACR_DISD | \
+ CF_CACR_CEIB | CF_CACR_DCM | \
+ CF_CACR_EUSP)
+
+/*-----------------------------------------------------------------------
+ * Chipselect bank definitions
+ */
+/*
+ * CS0 - NOR Flash 1, 2, 4, or 8MB
+ * CS1 - Available
+ * CS2 - Available
+ * CS3 - Available
+ * CS4 - Available
+ * CS5 - Available
+ * CS6 - Available
+ * CS7 - Available
+ */
+#ifdef NORFLASH_PS32BIT
+# define CONFIG_SYS_CS0_BASE 0xFFC00000
+# define CONFIG_SYS_CS0_MASK 0x003f0001
+# define CONFIG_SYS_CS0_CTRL 0x00001D00
+#else
+# define CONFIG_SYS_CS0_BASE 0xFFE00000
+# define CONFIG_SYS_CS0_MASK 0x001f0001
+# define CONFIG_SYS_CS0_CTRL 0x00001D80
+#endif
+
+#endif /* _M5329EVB_H */
Code Review / kvmfornfv.git / blobdiff