--- /dev/null
+/*
+ * (C) Copyright 2000-2010
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ * Klaus Heydeck, Kieback & Peter GmbH & Co KG, heydeck@kieback-peter.de
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+/*
+ * board/config.h - configuration options, board specific
+ * Derived from ../tqm8xx/tqm8xx.c
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+
+#define CONFIG_MPC855 1 /* This is a MPC855 CPU */
+#define CONFIG_KUP4K 1 /* ...on a KUP4K module */
+
+#define CONFIG_SYS_TEXT_BASE 0x40000000
+
+#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */
+#undef CONFIG_8xx_CONS_SMC2
+#undef CONFIG_8xx_CONS_NONE
+#define CONFIG_BAUDRATE 115200 /* console baudrate */
+#define CONFIG_BOOTDELAY 1 /* autoboot after 1 second */
+
+#define CONFIG_BOARD_TYPES 1 /* support board types */
+
+#undef CONFIG_BOOTARGS
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+"slot_a_boot=setenv bootargs root=/dev/sda2 ip=off;" \
+ "run addhw; mw.b 400000 00 80; diskboot 400000 0:1; bootm 400000\0" \
+"slot_b_boot=setenv bootargs root=/dev/sda2 ip=off;" \
+ "run addhw; mw.b 400000 00 80; diskboot 400000 2:1; bootm 400000\0" \
+"nfs_boot=mw.b 400000 00 80; dhcp; run nfsargs addip addhw; bootm 400000\0" \
+"fat_boot=mw.b 400000 00 80; fatload ide 2:1 400000 st.bin; run addhw; \
+ bootm 400000 \0" \
+"panic_boot=echo No Bootdevice !!! reset\0" \
+"nfsargs=setenv bootargs root=/dev/nfs rw nfsroot=${rootpath}\0" \
+"ramargs=setenv bootargs root=/dev/ram rw\0" \
+"addip=setenv bootargs ${bootargs} ip=${ipaddr}::${gatewayip}" \
+ ":${netmask}:${hostname}:${netdev}:off\0" \
+"addhw=setenv bootargs ${bootargs} ${mtdparts} console=${console} ${debug} \
+ hw=${hw} key1=${key1} panic=1 mem=${mem}\0" \
+"console=ttyCPM0,115200\0" \
+"netdev=eth0\0" \
+"contrast=20\0" \
+"silent=1\0" \
+"mtdparts=" MTDPARTS_DEFAULT "\0" \
+"load=tftp 200000 bootloader-4k.bitmap;tftp 100000 bootloader-4k.bin\0" \
+"update=protect off 1:0-9;era 1:0-9;cp.b 100000 40000000 ${filesize};" \
+ "cp.b 200000 40050000 14000\0"
+
+#define CONFIG_BOOTCOMMAND \
+ "run fat_boot;run slot_b_boot;run slot_a_boot;run nfs_boot;run panic_boot"
+
+#define CONFIG_PREBOOT "setenv preboot; saveenv"
+
+#define CONFIG_MISC_INIT_R 1
+#define CONFIG_MISC_INIT_F 1
+
+#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
+#undef CONFIG_SYS_LOADS_BAUD_CHANGE /* don't allow baudrate change */
+
+#define CONFIG_WATCHDOG 1 /* watchdog enabled */
+
+#define CONFIG_STATUS_LED 1 /* Status LED enabled */
+
+#undef CONFIG_CAN_DRIVER /* CAN Driver support disabled */
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_SUBNETMASK
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_BOOTFILESIZE
+
+#define CONFIG_MAC_PARTITION
+#define CONFIG_DOS_PARTITION
+
+/*
+ * enable I2C and select the hardware/software driver
+ */
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_SOFT /* I2C bit-banged */
+#define CONFIG_SYS_I2C_SOFT_SPEED 93000 /* 93 kHz is supposed to work */
+#define CONFIG_SYS_I2C_SOFT_SLAVE 0xFE
+
+/*
+ * Software (bit-bang) I2C driver configuration
+ */
+#define PB_SCL 0x00000020 /* PB 26 */
+#define PB_SDA 0x00000010 /* PB 27 */
+
+#define I2C_INIT (immr->im_cpm.cp_pbdir |= PB_SCL)
+#define I2C_ACTIVE (immr->im_cpm.cp_pbdir |= PB_SDA)
+#define I2C_TRISTATE (immr->im_cpm.cp_pbdir &= ~PB_SDA)
+#define I2C_READ ((immr->im_cpm.cp_pbdat & PB_SDA) != 0)
+#define I2C_SDA(bit) if(bit) immr->im_cpm.cp_pbdat |= PB_SDA; \
+ else immr->im_cpm.cp_pbdat &= ~PB_SDA
+#define I2C_SCL(bit) if(bit) immr->im_cpm.cp_pbdat |= PB_SCL; \
+ else immr->im_cpm.cp_pbdat &= ~PB_SCL
+#define I2C_DELAY udelay(2) /* 1/4 I2C clock duration */
+
+/*-----------------------------------------------------------------------
+ * I2C Configuration
+ */
+
+#define CONFIG_SYS_I2C_PICIO_ADDR 0x21 /* PCF8574 IO Expander */
+#define CONFIG_SYS_I2C_RTC_ADDR 0x51 /* PCF8563 RTC */
+
+/* List of I2C addresses to be verified by POST */
+
+#define CONFIG_SYS_POST_I2C_ADDRS {CONFIG_SYS_I2C_PICIO_ADDR, \
+ CONFIG_SYS_I2C_RTC_ADDR, \
+ }
+
+#define CONFIG_RTC_PCF8563 /* use Philips PCF8563 RTC */
+
+#define CONFIG_SYS_DISCOVER_PHY
+#define CONFIG_MII
+
+/* Define to allow the user to overwrite serial and ethaddr */
+#define CONFIG_ENV_OVERWRITE
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_DATE
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_IDE
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_NFS
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_SNTP
+
+#ifdef CONFIG_POST
+ #define CONFIG_CMD_DIAG
+#endif
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#if defined(CONFIG_CMD_KGDB)
+#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
+#else
+#define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */
+#endif
+/* Print Buffer Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
+
+#define CONFIG_SYS_MEMTEST_START 0x000400000 /* memtest works on */
+#define CONFIG_SYS_MEMTEST_END 0x005C00000 /* 4 ... 92 MB in DRAM */
+#define CONFIG_SYS_ALT_MEMTEST 1
+#define CONFIG_SYS_MEMTEST_SCRATCH 0x90000200 /* using latch as scratch register */
+
+#define CONFIG_SYS_LOAD_ADDR 0x400000 /* default load address */
+
+#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 115200 }
+
+#define CONFIG_SYS_CONSOLE_INFO_QUIET 1
+
+/*
+ * Low Level Configuration Settings
+ * (address mappings, register initial values, etc.)
+ * You should know what you are doing if you make changes here.
+ */
+/*-----------------------------------------------------------------------
+ * Internal Memory Mapped Register
+ */
+#define CONFIG_SYS_IMMR 0xFFF00000
+
+/*-----------------------------------------------------------------------
+ * Definitions for initial stack pointer and data area (in DPRAM)
+ */
+#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR
+#define CONFIG_SYS_INIT_RAM_SIZE 0x2F00 /* Size of used area in DPRAM */
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
+
+/*-----------------------------------------------------------------------
+ * Start addresses for the final memory configuration
+ * (Set up by the startup code)
+ * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
+ */
+#define CONFIG_SYS_SDRAM_BASE 0x00000000
+#define CONFIG_SYS_FLASH_BASE 0x40000000
+#define CONFIG_SYS_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
+#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+
+/*-----------------------------------------------------------------------
+ * FLASH organization
+ */
+#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
+#define CONFIG_SYS_MAX_FLASH_SECT 19 /* max number of sectors on one chip */
+
+#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
+
+#define CONFIG_ENV_IS_IN_FLASH 1
+#define CONFIG_ENV_OFFSET 0x40000 /* Offset of Environment Sector */
+#define CONFIG_ENV_SIZE 0x1000 /* Total Size of Environment Sector */
+#define CONFIG_ENV_SECT_SIZE 0x10000
+
+/*-----------------------------------------------------------------------
+ * Dynamic MTD partition support
+ */
+#define MTDPARTS_DEFAULT "mtdparts=40000000.flash:256k(u-boot)," \
+ "64k(env)," \
+ "128k(splash)," \
+ "512k(etc)," \
+ "64k(hw-info)"
+
+/*-----------------------------------------------------------------------
+ * Hardware Information Block
+ */
+#define CONFIG_SYS_HWINFO_OFFSET 0x000F0000 /* offset of HW Info block */
+#define CONFIG_SYS_HWINFO_SIZE 0x00000100 /* size of HW Info block */
+#define CONFIG_SYS_HWINFO_MAGIC 0x4B26500D /* 'K&P<CR>' */
+
+/*-----------------------------------------------------------------------
+ * Cache Configuration
+ */
+#define CONFIG_SYS_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */
+#if defined(CONFIG_CMD_KGDB)
+#define CONFIG_SYS_CACHELINE_SHIFT 4 /* log base 2 of the above value */
+#endif
+
+/*-----------------------------------------------------------------------
+ * SYPCR - System Protection Control 11-9
+ * SYPCR can only be written once after reset!
+ *-----------------------------------------------------------------------
+ * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
+ */
+#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
+
+/*-----------------------------------------------------------------------
+ * SIUMCR - SIU Module Configuration 11-6
+ *-----------------------------------------------------------------------
+ * PCMCIA config., multi-function pin tri-state
+ */
+#define CONFIG_SYS_SIUMCR (SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC00)
+
+/*-----------------------------------------------------------------------
+ * TBSCR - Time Base Status and Control 11-26
+ *-----------------------------------------------------------------------
+ * Clear Reference Interrupt Status, Timebase freezing enabled
+ */
+#define CONFIG_SYS_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF)
+
+/*-----------------------------------------------------------------------
+ * RTCSC - Real-Time Clock Status and Control Register 11-27
+ *-----------------------------------------------------------------------
+ */
+#define CONFIG_SYS_RTCSC (RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE)
+
+/*-----------------------------------------------------------------------
+ * PISCR - Periodic Interrupt Status and Control 11-31
+ *-----------------------------------------------------------------------
+ * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
+ */
+#define CONFIG_SYS_PISCR (PISCR_PS | PISCR_PITF)
+
+/*-----------------------------------------------------------------------
+ * PLPRCR - PLL, Low-Power, and Reset Control Register 15-30
+ *-----------------------------------------------------------------------
+ * Reset PLL lock status sticky bit, timer expired status bit and timer
+ * interrupt status bit
+ *
+ * If this is a 80 MHz CPU, set PLL multiplication factor to 5 (5*16=80)!
+ */
+#define CONFIG_SYS_PLPRCR ( (5-1)<<PLPRCR_MF_SHIFT | PLPRCR_TEXPS | PLPRCR_TMIST )
+
+/*-----------------------------------------------------------------------
+ * SCCR - System Clock and reset Control Register 15-27
+ *-----------------------------------------------------------------------
+ * Set clock output, timebase and RTC source and divider,
+ * power management and some other internal clocks
+ */
+#define SCCR_MASK SCCR_EBDF00
+#define CONFIG_SYS_SCCR (SCCR_TBS | SCCR_EBDF01 | \
+ SCCR_COM00 | SCCR_DFSYNC00 | SCCR_DFBRG00 | \
+ SCCR_DFNL000 | SCCR_DFNH000 | SCCR_DFLCD000 | \
+ SCCR_DFALCD00)
+
+/*-----------------------------------------------------------------------
+ * PCMCIA stuff
+ *-----------------------------------------------------------------------
+ *
+ */
+
+/* KUP4K use both slots, SLOT_A as "primary". */
+#define CONFIG_PCMCIA_SLOT_A 1
+
+#define CONFIG_SYS_PCMCIA_MEM_ADDR (0xE0000000)
+#define CONFIG_SYS_PCMCIA_MEM_SIZE ( 64 << 20 )
+#define CONFIG_SYS_PCMCIA_DMA_ADDR (0xE4000000)
+#define CONFIG_SYS_PCMCIA_DMA_SIZE ( 64 << 20 )
+#define CONFIG_SYS_PCMCIA_ATTRB_ADDR (0xE8000000)
+#define CONFIG_SYS_PCMCIA_ATTRB_SIZE ( 64 << 20 )
+#define CONFIG_SYS_PCMCIA_IO_ADDR (0xEC000000)
+#define CONFIG_SYS_PCMCIA_IO_SIZE ( 64 << 20 )
+
+#define PCMCIA_SOCKETS_NO 2
+#define PCMCIA_MEM_WIN_NO 8
+/*-----------------------------------------------------------------------
+ * IDE/ATA stuff (Supports IDE harddisk on PCMCIA Adapter)
+ *-----------------------------------------------------------------------
+ */
+
+#define CONFIG_IDE_PREINIT 1 /* Use preinit IDE hook */
+#define CONFIG_IDE_8xx_PCCARD 1 /* Use IDE with PC Card Adapter */
+
+#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */
+#define CONFIG_IDE_LED 1 /* LED for ide supported */
+#undef CONFIG_IDE_RESET /* reset for ide not supported */
+
+#define CONFIG_SYS_IDE_MAXBUS 2
+#define CONFIG_SYS_IDE_MAXDEVICE 4
+
+#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000
+
+#define CONFIG_SYS_ATA_IDE1_OFFSET (4 * CONFIG_SYS_PCMCIA_MEM_SIZE)
+
+#define CONFIG_SYS_ATA_BASE_ADDR CONFIG_SYS_PCMCIA_MEM_ADDR
+
+/* Offset for data I/O */
+#define CONFIG_SYS_ATA_DATA_OFFSET (CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
+
+/* Offset for normal register accesses */
+#define CONFIG_SYS_ATA_REG_OFFSET (2 * CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
+
+/* Offset for alternate registers */
+#define CONFIG_SYS_ATA_ALT_OFFSET 0x0100
+
+/*-----------------------------------------------------------------------
+ *
+ *-----------------------------------------------------------------------
+ *
+ */
+#define CONFIG_SYS_DER 0
+
+/*
+ * Init Memory Controller:
+ *
+ * BR0/1 and OR0/1 (FLASH)
+ */
+#define FLASH_BASE0_PRELIM 0x40000000 /* FLASH bank #0 */
+
+/* used to re-map FLASH both when starting from SRAM or FLASH:
+ * restrict access enough to keep SRAM working (if any)
+ * but not too much to meddle with FLASH accesses
+ */
+#define CONFIG_SYS_REMAP_OR_AM 0x80000000 /* OR addr mask */
+#define CONFIG_SYS_PRELIM_OR_AM 0xE0000000 /* OR addr mask */
+
+/*
+ * FLASH timing:
+ */
+#define CONFIG_SYS_OR_TIMING_FLASH (OR_ACS_DIV2 | OR_CSNT_SAM | \
+ OR_SCY_5_CLK | OR_EHTR | OR_BI)
+
+#define CONFIG_SYS_OR0_REMAP \
+ (CONFIG_SYS_REMAP_OR_AM | CONFIG_SYS_OR_TIMING_FLASH)
+#define CONFIG_SYS_OR0_PRELIM \
+ (CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_FLASH)
+#define CONFIG_SYS_BR0_PRELIM \
+ ((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_PS_16 | BR_V )
+
+
+/* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care) */
+#define CONFIG_SYS_OR_TIMING_SDRAM 0x00000A00
+
+/*
+ * Memory Periodic Timer Prescaler
+ *
+ * The Divider for PTA (refresh timer) configuration is based on an
+ * example SDRAM configuration (64 MBit, one bank). The adjustment to
+ * the number of chip selects (NCS) and the actually needed refresh
+ * rate is done by setting MPTPR.
+ *
+ * PTA is calculated from
+ * PTA = (gclk * Trefresh) / ((2 ^ (2 * DFBRG)) * PTP * NCS)
+ *
+ * gclk CPU clock (not bus clock!)
+ * Trefresh Refresh cycle * 4 (four word bursts used)
+ *
+ * 4096 Rows from SDRAM example configuration
+ * 1000 factor s -> ms
+ * 32 PTP (pre-divider from MPTPR) from SDRAM example configuration
+ * 4 Number of refresh cycles per period
+ * 64 Refresh cycle in ms per number of rows
+ * --------------------------------------------
+ * Divider = 4096 * 32 * 1000 / (4 * 64) = 512000
+ *
+ * 50 MHz => 50.000.000 / Divider = 98
+ * 66 Mhz => 66.000.000 / Divider = 129
+ * 80 Mhz => 80.000.000 / Divider = 156
+ */
+#if defined(CONFIG_80MHz)
+#define CONFIG_SYS_MAMR_PTA 156
+#elif defined(CONFIG_66MHz)
+#define CONFIG_SYS_MAMR_PTA 129
+#else /* 50 MHz */
+#define CONFIG_SYS_MAMR_PTA 98
+#endif /*CONFIG_??MHz */
+
+/*
+ * For 16 MBit, refresh rates could be 31.3 us
+ * (= 64 ms / 2K = 125 / quad bursts).
+ * For a simpler initialization, 15.6 us is used instead.
+ *
+ * #define CONFIG_SYS_MPTPR_2BK_2K MPTPR_PTP_DIV32 for 2 banks
+ * #define CONFIG_SYS_MPTPR_1BK_2K MPTPR_PTP_DIV64 for 1 bank
+ */
+#define CONFIG_SYS_MPTPR 0x400
+
+/*
+ * MAMR settings for SDRAM
+ */
+
+/* 8 column SDRAM */
+#define CONFIG_SYS_MAMR_8COL 0x68802114
+/* 9 column SDRAM */
+#define CONFIG_SYS_MAMR_9COL 0x68904114
+
+/*
+ * Chip Selects
+ */
+#define CONFIG_SYS_OR0
+#define CONFIG_SYS_BR0
+
+#define CONFIG_SYS_OR1_8COL 0xFF000A00
+#define CONFIG_SYS_BR1_8COL 0x00000081
+#define CONFIG_SYS_OR2_8COL 0xFE000A00
+#define CONFIG_SYS_BR2_8COL 0x01000081
+#define CONFIG_SYS_OR3_8COL 0xFC000A00
+#define CONFIG_SYS_BR3_8COL 0x02000081
+
+#define CONFIG_SYS_OR1_9COL 0xFE000A00
+#define CONFIG_SYS_BR1_9COL 0x00000081
+#define CONFIG_SYS_OR2_9COL 0xFE000A00
+#define CONFIG_SYS_BR2_9COL 0x02000081
+#define CONFIG_SYS_OR3_9COL 0xFE000A00
+#define CONFIG_SYS_BR3_9COL 0x04000081
+
+#define CONFIG_SYS_OR4 0xFFFF8926
+#define CONFIG_SYS_BR4 0x90000401
+
+#define CONFIG_SYS_OR5 0xFFC007F0 /* EPSON: 4 MB 17 WS or externel TA */
+#define CONFIG_SYS_BR5 0x80080801 /* Start at 0x80080000 */
+
+#define LATCH_ADDR 0x90000200
+
+#define CONFIG_AUTOBOOT_KEYED /* use key strings to stop autoboot */
+#define CONFIG_AUTOBOOT_STOP_STR "."
+#define CONFIG_SILENT_CONSOLE 1
+#define CONFIG_SYS_DEVICE_NULLDEV 1 /* enble null device */
+#define CONFIG_VERSION_VARIABLE 1
+
+/* pass open firmware flat tree */
+#define CONFIG_OF_LIBFDT 1
+#define CONFIG_OF_BOARD_SETUP 1
+
+#endif /* __CONFIG_H */
Code Review / kvmfornfv.git / blobdiff